Search
Filters
total: 54
Search results for: QUASI-TWIN RESONANT FREQUENCIES
-
Determination of the minimal critical rotational speeds of the circular saw blades with the quasi-twin resonant frequencies
PublicationTo determine the minimal critical rotational speeds of the circular saw blades is the fundamental aspect of obtaining the range of the rotational operating speeds, by which the circular saw blade can work with required stability. While for the circular saw blades with full-homogeneous bodies the determination of such rotational speeds is the relatively low level of difficulty function, whereas for circular saw blades with more...
-
Comparison of the impact test and the harmonic test in measurements of natural resonant frequencies of circular saw blades
PublicationIn this paper results of measurements of natural resonant frequencies of circular saw blades with the impact test and the harmonic test are presented. Comparison of these two methods revealed that during testing of circular saw blades, in which bodies the open and closed notches (cuts) for cleaning of knives are present, with the harmonic test method it has been observed appearing of quasi-twin resonant frequencies, whereas the...
-
The effect of circular saw blade clamping diameter on its resonant frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with the...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
Non-isolated resonant quasi-Z-source network DC–DC converter
PublicationA novel non-isolated resonant quasi-impedance (quasi-Z)-source network DC–DC converter is proposed. The resonant impedance source network is derived from the quasi-Z-source network by including the autotransformer-based resonant cell instead of the second inductor of the quasi-Z-network. The leakage inductance of the autotransformer and two resonant capacitors connected in series with the autotransformer windings constitute a high-frequency...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublicationUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
-
Quasi-resonant DC-link voltage inverter with enhanced zero-voltage switching control
PublicationA new topology modification of the parallel quasi-resonant circuit for a dc-link voltage inverter enables regulation of the zero voltage dc-link subperiods and the dc-link voltage gradient settings. The proposed circuit is based on four MOSFET switches with free-wheeling diodes for controlled quasi-resonant recharging between L-C tank in order to assure inverter zero voltage switching (ZVS) conditions. Design optimization of the...
-
Accurate modeling of quasi-resonant inverter fed IM drive
PublicationIn this paper wide-band modeling methodology of a parallel quasi-resonant dc link inverter (PQRDCLI) fed induction machine (IM) is presented. The modeling objective is early-design stage prediction of conductive electromagnetic interference (EMI) emissions of the considered converter fed IM drive system. Operation principles of the selected topology of PQRDCLI feeding IM drive are given. Modeling of the converter drive system is...
-
A predictive estimation based control strategy for a quasi-resonant dc-link inverter
PublicationIn this paper the predictive estimation based control strategy for a quasi-resonant dc link inverter (PQRDCLI) is developed. Instead of direct measurement of dc link input inverter current – its estimation with one step prediction is applied. The PQRDCLI fed induction motor, controlled with a predictive current estimation stabilized inverter output voltage slopes independently of load. Moreover, reduction of overvoltage spikes...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublicationThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Resonant Frequencies in the Open Microstrip Structures Placed on Curved Surfaces
PublicationThe paper presents the research on open microstrip structures placed on curved surfaces such as cylindrical, elliptical or spherical. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields into suitable function series. Utilizing the continuity conditions the boundary problem is formulated which is solved with the use of method of moments. The investigated structures find application...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Modeling of a Quasi-Resonant DC Link Inverter Dedicated to Common-Mode Voltage and Ground Current Reduction
PublicationIn this paper, the modeling methodology of the AC drive system with a Parallel Quasi-Resonant DC Link Inverter (PQRDCLI) is described. A presented modeling approach is an attractive tool used for the effective evaluation of a common-mode (CM) voltage and grounds current reduction methods. Designed models of inverter, induction machine (IM), and cable are simple, thus the methods for parameter extraction are not complicated. Verification...
-
Modeling of free vibrations and resonant frequencies of simply-supported submerged horizontal plate
PublicationA theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases...
-
Efficient calculation of the resonant frequencies of a SIW resonator with FDFD-based macromodel algorithm
PublicationW pracy przedstawiono efektywną metodę do analizy struktur ze integrowanym podłożem (SIW). W celu szybkiego obliczenia częstotliwości rezonansowych używany jest algorytm FDFD z zaimplementowanymi makromodelami.
-
Quasi-resonant dc-link inverter with a reduced number of active elements
PublicationW artykule przedstawiono nową topologię równoległego quasi-rezonansowego obwodu pośredniczącego falownika napięcia. Opisano sekwencje miękkiej komutacji falownika w dwukierunkowym trybie pracy falowniczej i prostowniczej. Analiza układu została zweryfikowana badaniami symulacyjnymi i eksperymentalnymi. Przedstawiona topologia odznacza się prostą strukturą oraz małą ilością elementów aktywnych. Dzięki zastosowaniu krzepkiej strategii...
-
A non-quasi-static small-signal model of the four-terminal MOSFET for radio and microwave frequencies.
PublicationW pracy zaprezentowano nowy małosygnałowy model tranzystora MOS, w którymuwzględnia się efekt nasycenia prędkości nośników. Model jest spójny fizycznie i może być stosowany w analizie dowolnej konfiguracji włączenia tranzystora.
-
A non-quasi-static-signal MOSFET model for radio and microware frequencies including spreading gate resistances and capacitaces.
PublicationZaprezentowano nowy, spójny fizycznie nie-quasi-statyczny model małosygnałowy tranzystora MOS słuszny od 0 Hz aż do częstotliwości mikrofalowych. Scharakteryzowano właściwości nowego czterokońcówkowego modelu. Model został zweryfikowany eksperymentalnie aż do częstotliwości 27 GHz.
-
Mode vibrations of plates – experimental analysis
PublicationIn this paper results of the square MDF plate and circular saw blades examination with the use of the harmonic method to static identification of resonant frequencies and shapes of mode vibrations are presented. Obtained results reveled that for circular saws with large holes in a saw blade appeared two resonant frequencies for the same nodal number.
-
WARUNKI REZONANSOWE W WĘŹLE Z KOMPENSATOREM SVC
PublicationInstalowanie kompensatorów statycznych w sieciach rozdzielczych i przesyłowych służy poprawie profili napięciowych. Kompensatory jako źródła mocy biernej zwiększają stabilność napięciową systemu. Pozwalają także na szybszą odbudowę systemu w przypadku awarii napięciowej. W artykule zaprezentowano wpływ struktury i wysterowania układu SVC na zmianę impedancji w układzie zasilania. Ma to bezpośredni wpływ na częstotliwości, przy...
-
Diagnostics of high-voltage varistor quality using resonant ultrasound spectroscopy
PublicationResonant spectroscopy is an effective nondestructive testing method focused on defects detection in tested objects. Resonance spectrum contains an information about the mechanical properties and particularly about the structural homogeneity of the whole object. A swept frequency method has been used to measure the selected resonant frequencies range. The system for measurement of resonant ultrasound spectroscopy of high-voltage...
-
Examples of AFM applications in liquid environment
Open Research DataImportant advantage of atomic force microscopy (also tunneling microscopy) is the ability to work in different environments (vacuum, controlled atmosphere, liquid environment). The last one, open interesting possibilities, such as imaging of delicate biological materials in their natural state. The use of electrochemical mode allows for the modification...
-
Wykorzystanie metody Neldera-Meada do identyfikacji wartości parametrów niequasi-statycznego modelu małosygnałowego tranzystora MOS
PublicationW artykule zaprezentowano wyniki zastosowania metody sympleksu Neldera-Meada do ekstrakcji wartości parametrów niequasi-stycznego modelu małosygnałowego tranzystora MOS. Przedstawiono równoważny elektryczny schemat zastępczy i model matematyczny nowego modelu małosygnałowego MOSFETa dla częstotliwości mikrofalowych. Opisano zaimplementowany algorytm i otrzymane rezultaty badań.
-
Measurements of electrically small antenna radiation patterns in non-anechoic environments using TGM
Open Research DataThe dataset contains raw and processed measurements of radiation pattern characteristics performed in non-anechoic regime for four antenna structures: a spline-parameterized Vivaldi structure, a compact spline-based monopole, super-ultrawideband antenna, and a quasi-Yagi component. The responses have been obtained at the selected frequencies of interest...
-
Comparison of natural frequencies of a circular saw blade obtained empirically and with FEM
PublicationThe knowledge of the natural frequencies’ values of circular saw blades is necessary to determine the minimal critical rotational speed in which they can work with required stability. Moreover, testing the circular saw blades with more complicated shapes, e.g. which have additional holes inside blades for cleaning knifes or additional indirect teeth in gullets, reveals some kind of problematic properties of these saw blades. The...
-
Compact Substrate-Integrated Hexagonal Cavity-Backed Self-Hexaplexing Antenna for Sub-6 GHz Applications
PublicationA self-multiplexing SIW antenna based on hexagonal SIW cavity is proposed. The self-hexaplexing antenna consists of different sizes of resonating elements, which provide the hexaband operations. The antenna resonates at 5 GHz, 5.17 GHz, 5.32 GHz, 5.53 GHz, 5.62 GHz, and 5.72 GHz by employing different slot lengths between the resonating elements. The proposed antenna provides the individual tunable characteristics of the operating...
-
Multi-transformer primary-side regulated flyback converter for supplying isolated IGBT and MOSFET drivers
PublicationThis paper presents primary-side voltage regulated multi-transformer quasi-resonant flyback converter (MTFC) for supplying isolated power switch drivers. The proposed topology offers distinct advantages over frequently used flyback converter possessing one high frequency transformer with isolated multiple outputs. Particularly, when a large number of separate dc supply units is required, then MTFC enables improved regular distribution...
-
A CMRC-based compact rat-race coupler with harmonic suppression
PublicationIn this paper, an eective miniaturization technique exploiting compact microstrip resonant cells has been discussed and experimentally validated on the basis of a 3-dB microstrip rat-race coupler. The application of the method proposed has resulted in 91 % circuit area reduction in comparison to a conventional rat-race coupler. Experimental results show good agreement with theoretical characteristics, as well as an additional eect,...
-
Ultrasonic spectroscopy of silicon single crystal
PublicationSpecimens of Si single crystals with different crystal orientation [100] and [110] were studied by the electro-ultrasonic spectroscopy (EUS) and Resonant Ultrasonic Spectroscopy (RUS). A silicon single crystal is an anisotropic crystal, so its properties are different in different directions in the material relative to the crystal orientation. EUS is based on interaction of two signals: electric AC signal and ultrasonic signal,...
-
Hybrid piezoelectric motor based on electroactive lubrication principle
PublicationA novel conception of hybrid piezoelectric motor is presented in this paper. Proposed conception required synchronised work of quasi-static and resonant piezoelectric actuators that results in a rotary movement. The motor's working principle is explained and the main characteristics are described. Studied topology is compared to the existing piezoelectric motors with regards to its field of applications. The assembling process...
-
Generalized adaptive notch filters with frequency debiasing for tracking of polynomial phase systems
PublicationGeneralized adaptive notch filters are used for identification/tracking of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. For general patterns of frequency variation the generalized adaptive notch filtering algorithms yield biased frequency estimates. We show that when system frequencies change slowly in a smooth way, the estimation bias can...
-
Substrate Integrated Waveguide-Based Frequency-Tunable Self-Octaplexing Antenna
PublicationThis communication presents the first-ever substrate integrated waveguide (SIW)-based frequency-tunable self-octaplexing antenna (SOA) for wireless communication. The structure is arranged by implementing eight distinct patches with planar 50-ohm feedlines at the top of the SIW cavity, which realize eight distinct resonant frequencies. Independent tuning of each resonant frequency is achieved by incorporating appropriately allocated...
-
A Substrate Integrated Waveguide (SIW) Bandpass Filter in A Box Configuration With Frequency-Dependent Coupling
PublicationThis letter presents the design of a microwave bandpass filter with frequency-dependent coupling implemented in substrate integrated waveguide (SIW) technology. The proposed filter implements a four-pole generalized Chebyshev filtering function with two transmission zeros. Resonators are arranged in an extended box configuration with dispersive coupling on a main signal path, which produces an extra zero in comparison to classical...
-
Adaptive estimation of the transformer stray capacitances for DC–DC converter modelling
PublicationNew low cost and accurate estimation method of transformer stray capacitances for wide band DC–DC converter modelling and design is proposed. The Wiener filter (WF) method is applied to estimate the transformer impedance – referred to the selected transformer winding configurations. Laboratory tests are used to adapt the filter, that is to find optimal impedance which minimises mean square error between measured, noise perturbed...
-
On the Nonlinea Distortions of Sound and its Coupling with Other Modes in a Gasesous Plasma with Finite Electric Conductivity in a Magnetic Field
PublicationNonlinear phenomena of the planar and quasi-planar magnetoacoustic waves are considered. We focus on deriving of equations which govern nonlinear excitation of the non-wave motions by the intense sound in initially static gaseous plasma. The plasma is treated as an ideal gas with finite electrical conductivity permeated by a magnetic field orthogonal to the trajectories of gas particles. This introduces dispersion of a flow. Magnetoacoustic...
-
Efficient Fabry-Perot Open Resonator Analysis by the use of a Scattering Matrix Method
PublicationIn this paper a comparative study of the computational efficiency of two modeling methods applied to the analysis of the plano- and double-concave Fabry-Perot open resonators is presented. In both numerical approaches, a scattering matrix method was applied, which allows splitting the analysis of the resonator into several sections, including the one with a spherical mirror, which requires the largest computing resources. Two modeling...
-
Ionospheric scintillations computation using real-time GPS observations
PublicationThe following paper presents the results of quasi-real-time determination of the values of phase scintillations indices at the period of ionospheric disturbances that occurred as a consequence of the Sun flares observed on March 7 and 9, 2012. Double-frequency observations with 1-second measurement interval from the EPN (EUREF Permanent Network) network sites located at high latitudes were used for the analysis. To determine the phase...
-
Efficient analysis of structures with rotatable elements using model order reduction
PublicationThis paper presents a novel full-wave technique which allows for a fast 3D finite element analysis of waveguide structures containing rotatable tuning elements of arbitrary shapes. Rotation of these elements changes the resonant frequencies of the structure, which can be used in the tuning process to obtain the S-characteristics desired for the device. For fast commutations of the response as the tuning elements are rotated, the...
-
A GPU Solver for Sparse Generalized Eigenvalue Problems with Symmetric Complex-Valued Matrices Obtained Using Higher-Order FEM
PublicationThe paper discusses a fast implementation of the stabilized locally optimal block preconditioned conjugate gradient (sLOBPCG) method, using a hierarchical multilevel preconditioner to solve nonHermitian sparse generalized eigenvalue problems with large symmetric complex-valued matrices obtained using the higher-order finite-element method (FEM), applied to the analysis of a microwave resonator. The resonant frequencies of the low-order...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Inverse Modeling and Optimization of CSRR-based Microwave Sensors for Industrial Applications
PublicationDesign optimization of multivariable resonators is a challenging topic in the area of microwave sensors for industrial applications. This paper proposes a novel methodology for rapid re-design and parameter tuning of complementary split-ring resonators (CSRRs). Our approach involves inverse surrogate models established using pre-optimized resonator data as well as analytical correction techniques to enable rapid adjustment of geometry...
-
PREDICTION OF SHIP MOTIONS IN IRREGULAR WAVES BASED ON RESPONSE AMPLITUDE OPERATORS EVALUATED EXPERIMENTALLY IN NOISE WAVES
PublicationThe most common methods for predicting ship roll motions in a specified sea state are direct measurements of motions in a representative irregular wave realisation (time domain) or calculations of motions from response amplitude operators (RAOs) in the frequency domain. The result of the first method is valid only for the tested sea state, whilst the second method is more flexible but less accurate. RAO-based predictions are calculated...
-
Efficient model order reduction for FEM analysis of waveguide structures and resonators
PublicationAn efficient model order reduction method for three-dimensional Finite Element Method (FEM) analysis of waveguide structures is proposed. The method is based on the Efficient Modal Order Reduction (ENOR) algorithm for creating macro-elements in cascaded subdomains. The resulting macro-elements are represented by very compact submatrices, leading to significant reduction of the overall number of unknowns. The efficiency of the model...
-
Designing a High-sensitivity Microscale Triple-band Biosensor based on Terahertz MTMs to provide a perfect absorber for Non-Melanoma Skin Cancer diagnostic
PublicationNon-melanoma skin cancer (NMSC) is among the most prevalent forms of cancer originating in the top layer of the skin, with basal cell carcinoma (BCC) and squamous cell carcinoma (SCC) being its primary categories. While both types are highly treatable, the success of treatment hinges on early diagnosis. Early-stage NMSC detection can be achieved through clinical examination, typically involving visual inspection. An alternative,...
-
Novel Complementary Resonator for Dielectric Characterization of Substrates Based on Permittivity and Thickness
PublicationThis paper presents a novel complementary resonator featuring high sensitivity, low fabrication cost, and improved performance. The proposed structure consists of a complementary concentric square and circular ring resonator (CCSCRR) with multiple splits to enhance the inductance of the resonator. The proposed CCSCRR is coupled to a microstrip transmission line with an impedance of fifty ohms to create a high-sensitivity sensor....
-
Low-Cost and Precise Automated Re-Design of Antenna Structures Using Interleaved Geometry Scaling and Gradient-Based Optimization
PublicationDesign of contemporary antennas is an intricate endeavor involving multiple stages, among others, tuning of geometry parameters. In particular, re-designing antennas to different operating frequencies, makes parametric optimization imperative to ensure the best achievable system performance. If the center frequency at the current design is distant from the target one, local tuning methods generally fail, whereas global algorithms...
-
Self-optimizing generalized adaptive notch filters - comparison of three optimization strategies
PublicationThe paper provides comparison of three different approaches to on-line tuning of generalized adaptive notch filters (GANFs) the algorithms used for identification/tracking of quasi-periodically varying dynamic systems. Tuning is needed to adjust adaptation gains, which control tracking performance of ANF algorithms, to the unknown and/or time time-varying rate of system nonstationarity. Two out ofthree compared approaches are classical...
-
Kriging metamodels and design re‐utilization for fast parameter tuning of antenna structures
PublicationThe paper addresses the problem of computationally efficient electromagnetic (EM)‐driven design closure of antenna structures. The foundations of the presented approach are fast kriging interpolation metamodels, utilized for two purposes: (a) producing a good starting point for further parameter tuning, and (b) yielding a reasonable Jacobian matrix estimate to jump‐start the optimization procedure. The models are rendered using...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublicationThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...