Filters
total: 2620
filtered: 2017
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: TUNEABLE LASER
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublicationIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Deterministic and statistical size effect during shearing of granular layer within a micro-polar hypoplasticity
PublicationArtykuł omawia deterministyczny i statystyczny efekt skali w materiałach granulowanych podczas ścinania cienkiej warstwy piasku między dwoma bardzo szorstkimi ścianami. Obliczenia wykonano metodą elementów skończonych na bazie mikropolarnego prawa hipoplastycznego. Przyjęto różne metody redukujące ilość realizacji pól losowych dla początkowego wskaźnika porowatości..
-
Improving osteoblasts cells proliferation via femtosecond laser surface modification of 3D-printed poly-ε-caprolactone scaffolds for bone tissue engineering applications
Publication -
SU-FF-T-192: Complete 3D QA for Rapid Arc Using BANG Polymer Gel and OCTOPUS-IQ Fast Laser CT Scanner
Publication -
High-Throughput Matrix-Assisted Laser Desorption Ionization-Time of Flight Mass Spectrometry as an Alternative Approach to Monitoring Drug Resistance of Hepatitis B Virus
Publication -
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry - How to apply optical technologies in the diagnosis of reinforced concrete elements?
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Mechanical Properties and Residual Stress Measurements of Grade IV Titanium and Ti-6Al-4V and Ti-13Nb-13Zr Titanium Alloys after Laser Treatment
PublicationNowadays, surface engineering focuses on research into materials for medical applications. Titanium and its alloys are prominent, especially Ti-6Al-4V and Ti-13Nb-13Zr. Samples made of pure grade IV titanium and the titanium alloys Ti-6Al-4V and Ti-13Nb-13Zr were modified via laser treatment with laser beam frequency f = 25 Hz and laser beam power P = 1000 W during a laser pulse with duration t = 1 ms. Subsequently, to analyze...
-
Określenie szybkości korozji stopu AlSi13Mg1CuNi nadtopionego laserowo w warunkach kriogenicznych = Corrosion rate determination of AlSi13Mg1CuNi alloy laser remelted at cryogenic conditions
PublicationW pracy przedstawiono wyniki badania szybkości korozji stopu AlSi13Mg1CuNi nadtopionego laserowo w warunkach kriogenicznych. Stop eksponowano w 0,01 M roztworze kwasu siarkowego H2SO4
-
Interferometric Sensor of Wavelength Detuning Using a Liquid Crystalline Polymer Waveplate
PublicationOperation of a polarization interferometer for measurement of the wavelength changes of a tunable semiconductor laser was investigated. A lambda/8 waveplate made from liquid crystalline polymer is placed in one of interferometers’ arms in order to generate two output signals in quadrature. Wavelength was measured with resolution of 2 pm in the wavelength range 628–635 nm. Drift of the interferometer, measured in the period of 500...
-
Modeling of light propagation in canine gingiva
PublicationThis study is a preliminary evaluation of the effectivenes of laser-based surgery of maxillary and mandibular bone in dogs. Current methods of gingivial surgery in dogs require the use of general anaesthesia.1, 2 The proposed methods of laser surgery can be performed on conscious dogs, which substantially reduces the associated risks. Two choices of lasers, Nd:YAG and a 930 nm semiconductor lasers were evaluated. The former is...
-
Structural and dynamic properties of water within the solvation layer around various conformations of the glycine-based polypeptide
PublicationSeveral conformations of the solvated glycine-based polypeptides were investigated using molecular dynamics simulations. Some properties of water in the neighbouring space around these molecules were investigated. It was found, that water forms a well-defined layer - the first solvation shell - around the peptide molecule, and thickness of this layer is independent of the peptide structure, and it equals to approximately 0.28 nm....
-
SAXS examination of the water evaporation process from silica materials coated with a polysaccharide–polyimine copolymer layer
Publication -
RPC communication layer and introduction to data protection for embedded PC based control and data acquisition module
Publication -
The influence of the spatial distribution of leads and ice floes on the atmospheric boundary layer over fragmented sea ice
Publication -
Long-term changes in the Leucobryo-Pinetum community: interactions between the tree-stand, understorey and moss layer
Publication -
Development of an Oxide Layer on Al 6061 Using Plasma Arc Electrolytic Oxidation in Silicate-Based Electrolyte
Publication -
Short-term changes in thickness and temperature of the active layer in summer in the Kaffiøyra region, NW Spitsbergen, Svalbard
Publication -
New possibilities of the passive layer cracking dynamics detection using a new Dynamic Electrochemical Impedance Spectroscopy.
PublicationNowa metoda Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej opracowana w Katedrze Elektrochemii, Korozji i Inżynierii Materiałowej Politechniki Gdańskiej daje możliwości określania charakterystyki impedancyjnej w dziedzinie czasu podczas procesu pękania ochronnej warstwy pasywnej. Fakt ten jest związany z procedurą analizującą wspomnianej techniki, która umożliwia selektywną analizę czasowo-częstotliwościową uzyskanych...
-
Sampling-based novel heterogeneous multi-layer stacking ensemble method for telecom customer churn prediction
PublicationIn recent times, customer churn has become one of the most significant issues in business-oriented sectors with telecommunication being no exception. Maintaining current customers is particularly valuable due to the high degree of rivalry among telecommunication companies and the costs of acquiring new ones. The early prediction of churned customers may help telecommunication companies to identify the causes of churn and design...
-
Design and multi-objective optimization of combinational digital circuits using evolutionaty algorithm with multi-layer chromosomes
PublicationW artykule przedstawiono zastosowanie algorytmów ewolucyjnych z wielowarstwowymi chromosomami do projektowania i optymalizacji wielokryterialnej kombinatorycznych układów cyfrowych. Kryteriami optymalizacji były: liczba bramek, liczba tranzystorów w układzie i czas propagacji sygnałów. Proponowaną metodą zaprojektowano i optymalizowano cztery układy wzięte z literatury. Uzyskane rezultaty porównano z wynikami otrzymanymi innymi...
-
Impact of European vaccination policies on seasonal influenza vaccination coverage rates: An update seven years later
Publication -
Structural and Dynamic Properties of Water within the Solvation Layer around Various Conformations of the Glycine-based Polypeptide
PublicationSeveral conformations of the solvated glycine-based polypeptides were investigated using molecular dynamics simulations. Some properties of water in the neighboring space around these molecules were investigated. It was found that water forms a well-defined layer—the first solvation shell—around the peptide molecule, and thickness of this layer is independent of the peptide structure and is equal to approximately 0.28 nm. Within...
-
Pumping effect measured by PIV method in multi-layer spike electrode EHD device for air cleaning
PublicationDust particles can be harmful for human health when inhaled. Especially dangerous are submicron dust particles, which can contain traces of toxic elements and can easily penetrate into human respiratory system. Thus, new devices for air cleaning are needed. In this work the flow velocity field patterns measured by Particle Image Velocimetry (PIV) method in an electrohydrodynamic (EHD) device for air cleaning are presented. The...
-
Common methods for the chiral determination of amphetamine and related compounds I. Gas, liquid and thin-layer chromatography
PublicationThis article reviews the most common, useful methods for the chiral determination of amphetamine (AM) and AM-deriveddesigner drugs in different of matrix, including blood, hair, urine, medicaments or standard solutions, taking into considerationarticles published in the past 15 years. We consider chromatographic methods (e.g., gas, liquid, high-performance liquid, and thinlayer). We describe several types of chiral derivatization...
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublicationWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
Low-cost performance-driven modelling of compact microwave components with two-layer surrogates and gradient kriging
PublicationUtilization of electromagnetic (EM) simulation tools has become indispensable for reliable evaluation of microwave components. As the cost of an individual analysis may already be considerable, the computational overhead associated with EM-driven tasks that require massive simulations (e.g., optimization) may turn prohibitive. One of mitigation methods is the employment of equivalent network models. Yet, they are incapable of accounting...
-
Density functional LCAO calculations of vibrational modes and phonon density of states in the strained single-layer phosphorene
PublicationThe paper presents an investigation of phosphorene under axial strain on the phonon density of states and vibrational modes. The studies were performed by means of density functional theory (DFT) within the linear combination of atomic orbitals (LCAO). The strained models were constructed using optimised supercell techniques. The vibrational mode spectra were estimated for strains applied for both the zigzag and armchair directions...
-
The accretion of the new ice layer on the surface of hexagonal ice crystal and the influence of the local electric field on this process
PublicationThe process of creation of a new layer of ice on the basal plane and on the prism plane of a hexagonal ice crystal is analyzed. It is demonstrated that the ordering of water molecules in the already existing crystal affects the freezing. On the basal plane, when the orientations of water molecules in the ice block are random, the arrangement of the new layer in a cubic manner is observed more frequently — approximately 1.7 times...
-
Determination of the refractive index and wavelength‐dependent optical properties of few‐layer CrCl3 within the Fresnel formalism
PublicationBased on previous reports on the optical microscopy contrast of mechanically exfoliated few layer CrCl3 transferred on 285 nmand 270 nmSiO2 on Si(100), we focus on the experimental determination of an effective mean complex refractive index via a fitting analysis based on the Fresnel equations formalism. Accordingly, the layer and wavelength-dependent absorbance and reflectance are calculated. Layer and wavelength-dependent optical...
-
Extreme weather layer method for implementation of nature-based solutions for climate adaptation: Case study Słupsk
PublicationOne of the most severe climate risks that is expected to affect all regions is related to stormwater. Climate models, constructed based on long-term trends, show that extreme weather events such as storms, cloudbursts and a large rise in sea level will be significant in the coming decades. Moreover, even the frequency and intensity of “normal” rainfall events, such as microbursts, are expected to be remarkably higher than today...
-
Tuning Electrochemical Performance by Microstructural Optimization of the Nanocrystalline Functional Oxygen Electrode Layer for Solid Oxide Cells
PublicationFurther development of solid oxide fuel cell (SOFC) oxygen electrodes can be achieved through improvements in oxygen electrode design by microstructure miniaturisation alongside nanomaterials implementation. In this work, improved electrochemical performance of an La0.6Sr0.4Co0.2Fe0.8O3-d (LSCF) cathode was achieved by the controlled modification of the La0.6Sr0.4CoO3-d (LSC) nanocrystalline interlayer introduced between a porous...
-
Optimization of the Hardware Layer for IoT Systems using a Trust Region Method with Adaptive Forward Finite Differences
PublicationTrust-region (TR) algorithms represent a popular class of local optimization methods. Owing to straightforward setup and low computational cost, TR routines based on linear models determined using forward finite differences (FD) are often utilized for performance tuning of microwave and antenna components incorporated within the Internet of Things systems. Despite usefulness for design of complex structures, performance of TR methods...
-
Cross-layer integration of network mechanisms for increasing efficiency of multimedia session support in IEEE 802.11s environment
PublicationWith an IEEE 802.11 wireless networks operating in Point-to-Multipoint mode being the most popular WLAN access technology employed today, it can be expected that a Wireless Mesh Network (WMN) based on the technology can provide significant advantages for such network systems. The IEEE 802.11s standard amendment provides the comprehensive set of mechanisms required to implement and deploy a WMN utilizing this widely popular technology....
-
Broadband Compact Single-Layer Magic-T Junction with Separation of DC Signals between All Ports
PublicationA novel structure for a four-port microstrip magic-T junction is presented. The device is composed of microstrip and slotline circuits etched onto two sides of a dielectric substrate. The device is extremely compact and occupies an area more than three times smaller than similar structures recently reported in the literature. The novelty of the device lies in the use of microstrip/slotline transitions for both input ports: summation...
-
Study of the Layer-Type BST Thin Film with X-ray Diffraction and X-ray Photoelectron Spectroscopy
PublicationIn the present paper, results of X-ray photoelectron studies of electroceramic thin films of barium strontium titanate, Ba1xSrxTiO3 (BST), composition deposited on stainless-steel substrates are presented. The thin films were prepared by the sol-gel method. A spin-coating deposition of BST layers with different chemical compositions was utilized so the layer-type structure of (0-2) connectivity was formed. After the deposition,...
-
Stalowe panele sandwicz - nowe możliwości wynikające z zastosowania spawania laserowego = All steel sandwich panels - new possibilities introduced by laser welding techniques
PublicationW artykule przedstawiono podstawowe dane na temat stalowych paneli typu sandwicz i technik ich wykonywania. Złącze takie charakteryzuje się specyficznymi własnościami, zdecydowanie odmiennymi od klasycznego połączenia spoiną pachwinową, którego cechy wytrzymałościowe i technologiczne są już dobrze opanowane. W podsumowaniu wykazano, że modelowanie jego geometrii musi być prowadzone na znacznie większym poziomie szczegółowości ze...
-
Automated Analysis of Images from Confocal Laser Scanning Microscopy Applied to Observation of Calcium Channel Subunits in Nerve Cell Model Line Subjected Electroporation and Calcium
Publication -
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublicationA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Morfologia warstw na bazie kobaltu napawanych plazmowo z zastosowaniem różnych technologii procesu.Morphology of the kobalt base laser produced by PTA method using the different technology.
PublicationPrzeanalizowano wpływ różnych parametrów napawania laserowego na morfologię i twardość warstwy otrzymanej z jednego proszku na bazie kobaltu. Stwierdzono różnice zarówno w budowie jak i twardości wytworzonych warstw.
-
3D modelling of beach topography changes caused by the tombolo phenomenon using terrestrial laser scanning (TLS) and unmanned aerial vehicle (UAV) photogrammetry on the example of the city of Sopot
Publication -
Physical and Mechanical Evaluation of Silicone-Based Double-Layer Adhesive Patch Intended for Keloids and Scar Treatment Therapy
PublicationGrowing interest in silicone elastomers for pharmaceutical purposes is due to both theirbeneficial material effect for scar treatment and their potential as drug carriers. Regarding their morphological structure, silicone polymers possess unique properties, which enable a wide range of applicability possibilities. The present study focused on developing a double-layer adhesive silicone film (DLASil) by evaluating its physical...
-
Nondestructive Methodology for Identification of Local Discontinuities in Aluminide Layer-Coated MAR 247 during Its Fatigue Performance
Publication -
Mn3O4 encapsulated in hollow carbon spheres coated by graphene layer for enhanced magnetization and lithium-ion batteries performance
Publication -
A novel stiffener skeleton strategy in catalytic carbonization system with enhanced carbon layer structure and improved fire retardancy
Publication -
Elastic multi-layer resilient IP-over-Flexgrid networking: Detailed cost analysis with bandwidth-variable transponders
Publication -
Integrated Processing: Quality Assurance Procedure of the Surface Layer of Machine Parts during the Manufacturing Step "Diamond Smoothing"
Publication -
Theoretical analysis of heat transfer between a liquid layer formed by an impinginf gas liquid jet AND a solid surface
PublicationHeat transfer phenomenon between a horizontal solid surface and a liquid layer created on a surface by an axisymmetrical liquid gas impinging jet has been analysed. The analytical treatment of the phenomenon is devoted to the area whose diameter is lower than the diameter of the hydraulic jump. W pracy przedstawiono teoretyczną analizę wymiany ciepła pomiędzy warstwą cieczy a stałą powierzchnią po której przepływa.
-
Modelling and experimental investigation of the phenomenon of brekdown of the liquid layer formed by an impinging two-phase air-water jet
PublicationW pracy przedstawiono analizę teoretyczną i badania eksperymentalne badania zjawiska rozrywania warstwy cieczy powstałej z uderzającej strugi
-
Comparative electrochemical analysis of the passive layer cracking process on aluminum alloys performed by means of DC and AC techniques
PublicationZbadano proces pękania warstwy pasywnej na stopach aluminium AA1050, AA5052, AA5056, oraz AA7005 w warunkach zmiennych naprężeń rozciągających i polaryzacji anodowej z wykorzystaniem techniki stałoprądowej, DEIS oraz emisji akustycznej (AE), jako metody porównawczej. Przeprowadzone badania pokazały przewagę techniki DEIS oraz emisji akustycznej nad klasyczną techniką stałoprądową. Wyznaczono dokładny moment pęknięcia warstwy pasywnej...
-
Experimental validation of the theoretical analysis of heat transfer between a liquid layer formed by an impinging jet and a solid surface
PublicationPrzedstawiono wyniki badań eksperymentalnych wymiany ciepła między poziomą powierzchnią a przepływająca po niej warstwa cieczy utworzoną z napływającej strugi gazowo-cieczowej. Wyniki badań eksperymentalnych porównano z modelem teoretycznym zjawiska.