Filters
total: 3143
filtered: 1283
displaying 1000 best results Help
Search results for: CYCLIC CARBONATES
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Synthesis and structural characterization of new cyclic siloxane with functionalized organic substituents
PublicationOcta(2-pyridyloxy)cyclotetrasiloxane was isolated as the product of the reaction between silicon disulfide and 2-hydroxypyridine. The new compound has been characterised by single crystal X-ray analysis, revealing a planar eight-membered ring with functionalized organic substituents on the silicon atoms.
-
Analysis of the cyclic load-unload-reload tests of VALMEX aged fabric
PublicationThe paper presents mechanical response of the VALMEX fabric during the cyclic loading-unloading and re-loading experiments. Two types of the aged material used for nearly 20 years as the roofing of the Forest Opera in Sopot (Poland) have been tested. The results have been separately obtained for the warp and fill di-rections. The comparative analysis has revealed that the material aged in service is more durable in the fill di-rection,...
-
Utilization of Gaseous Carbon Dioxide and Industrial Ca-rich Waste for Calcium Carbonate Precipitation: A Review
PublicationTechnologies for the management of various types of waste and the production of useful products from them are currently widely studied. Both carbon dioxide and calcium-rich waste from various production processes are problematic wastes that can be used to produce calcium carbonate. Therefore, the purpose of this paper is to provide an overview about the state of the development of processes that use these two wastes...
-
Influence of the particle size of carbonate-siliceous rock on the efficiency of phosphorous removal from domestic wastewater
PublicationtThe aim of the study was to determine the influence of the particle size of carbonate–silica rock (opoka)used in rock filters on the efficiency of phosphorus removal from domestic wastewater. The investigationswere carried out in a laboratory using a model consisting of three vertical flow filters with carbonate–silicarock of different particle sizes (G1= 1–2 mm; G2= 2–5 mm; G3= 5–10 mm). The tested rock was subjectedto decarbonising...
-
Effect of some organic solvent - water mixtures composion on precipitated calcium carbonate in carbonation process
PublicationPrecipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0 to 20 % (vol.). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution...
-
CO2 EMISSION TO THE ATMOSPHERE FROM CARBONATE WATERS: THE STUDY CASE OF THE LUBLIN UPLAND AND ROZTOCZE REGIONS
PublicationThe concentration of carbon dioxide dissolved in water (CO2(aq)) was measured in consecutive phases of the hydrological cycle. Its potentially possible degassing from groundwaters to the atmosphere was also assessed. The research was conducted in the area of occurrence of carbonate rocks of the Lublin Upland and Roztocze (SE Poland). The results of the measurements of CO2(aq) concentration varied as follows (min-max/mean): precipitation...
-
Effect of nanosilica on characteristics of carbonizates of phenol-formaldehyde resin – Fe(acac)3
Publication -
A Convenient Way to Methylated 2-Imidazolines. Syntheses of Fluorene and Triazine Cyclic Diamidines
PublicationOne N-methyl- and 4-substituted 2-imidazolines are described. Fluorene bisimidazolines were obtained in good yield (64-92%), starting from 2,7-dicyanofluorene and ammonium sulfide. In a two-step procedure the crude bisthioamide was reacted with excess diaminoalkane-ethanol (1:1 mixt.) in an oil bath. This new procedure is superior over std. methods. For the sake of comparison, a new triazine bisimidazoline (I) was prepd. by...
-
Cyclic Dipeptides as Building Units of Nano- and Microdevices: Synthesis, Properties, and Structural Studies
Publication -
Safe Operation of Underground Mining Vehicles Based on Cyclic Fatigue Monitoring of Powertrains
Publication -
Conformational studies of cyclic enkephalin analogues withL- orD-proline in position 3
Publication -
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Solid electrolyte gas sensors based on cyclic voltammetry with one active electrode
PublicationW artykule przedstawiono wyniki badań elektrokatalitycznego czujnika gazów toksycznych z jedną elektrodą aktywną.
-
Semi- incremental construction of minimal cyclic finite state automata usingcontinuation classes.
PublicationMinimalne automaty skończone są często wybierane do przedstawiania słowników morfologicznych języka naturalnego. Wśród ich zalet znajdują się duża szybkość rozpoznawania i małe wymagania pamięciowe. Tłumaczenie opisów morfologicznych opartych o klasy kontynuacji na minimalne, cykliczne automaty skończone jest tradycyjnie dokonywane w kilku fazach, zawierających tworzenie automatu niedeterministycznego z przejściami etykietowanymi...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
PublicationThe present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-4V lattice structures. In the study, diamond structures of titanium alloy produced by the additive laser powder bed fusion (LPBF) method with different degrees of relative density were used. Realistic geometric models of the studied mesostructures were generated using computed microtomography, taking into account the imperfections of the...
-
Effect of selected ammonia escape inhibitors on carbon dioxide capture and utilization via calcium carbonate precipitation
PublicationCarbon dioxide was used to precipitate CaCO3 with CaCl2 solution in the presence of NH3 as a CO2 absorption promoter. Compounds that were previously indicated as inhibitors of ammonia escape during CO2 absorption were also added to the reaction mixture. Inorganic salts, i.e. ZnCl2, CuCl2, CoCl2, and organic substances, i.e. glycerol, ethylene glycol and triethanolamine were tested inhibitors in this work. A model post-distillation...
-
The influence of ammonia and selcted amines on the characteristics of calcium carbonate precipitated from calcium chloride solutions via carbonation
PublicationThe precipitation of calcium carbonate was carried out by passing a gasous mixture of carbon dioxide and air into a calcium chloride solution. The selected compounds enhancing carbon dioxide absorption were used as additives which promote the formation of carbonate ions in the solution. The additives were ammonia, monoethanolamine, triethylamine and triethanolamine. The resulting calcium carbonate particles varied in polymorphic...
-
Synthesis, Pharmacological Evaluation, and Computational Studies of Cyclic Opioid Peptidomimetics Containing β3-Lysine
Publication -
Pharmacological Profile and Molecular Modeling of Cyclic Opioid Analogues Incorporating Various Phenylalanine Derivatives
Publication -
Behaviour of asphalt concrete in cyclic and static compression creep test with and without lateral confinement
PublicationArtykuł przedstawia wpływ metodyki badań na określanie parametrów betonu asfaltowego. Wykazano, że badania pełzania bez skrępowania bocznego w większym stopniu uwypuklają wpływ asfaltu na parametry badanego betonu asfaltowego natomiast w badaniach ze skrępowaniem bocznym, zarówno rola asfaltu jak i szkieletu mineralnego jest uwzględniana przy ocenie parametrów betonu asfaltowego. Ponadto wykazano, że lepszymi miarami do oceny betonu...
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
Application a laboratory stand for multi-symptoms tests for high cyclic fatigue of constructional material
PublicationThis paper describes a need of diagnostics present ship plants according to current technical state. In order to reach competent physical quantity describing fatigue of materials by congregated energy. This paper describes using some diagnostics methods (acoustic emission AE, vibration, thermovision, deformation) in order to definition fatigue state of construction material. The author tries to find correlation between measured...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublicationIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.
-
Cyclic analysis of thermal impedance of a passive layer of aluminium in a neutral borate buffer solution
PublicationW pracy przedstawiono wyniki badań warstwy pasywnej tworzącej się na stopie 1050 A w warunkach zmieniającej się temperatury. Zmiany realizowano w sposób cykliczny zwiększając a następnie zmniejszając temperaturę. W czasie zmian temperatury prowadzono badania metodę dynamicznej elektrochemicznej spektroskopii impedancyjnej. Stwierdzono największe zmiany parametrów elektrycznego schematu zastępczego w czasie pierwszego cyklu zmian....
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublicationThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublicationeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublicationThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublicationA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
Geometry of cycling track
PublicationThe paper describes the problems related to shaping of the geometry of the cycling track. The method of selection of the angle at the track curve is presented. Issues related to the selection of the appropriate transition curve and the superelevation section along the transition curve are presented. Reference to the recommendations presented in the literature and scientific papers has been made. Special attention...
-
Development and Validation of a Gas Chromatography Method for the Trace Level Determination of Allylamine in Sevelamer Hydrochloride and Sevelamer Carbonate Drug Substances
Publication -
Condition Monitoring of Horizontal Sieving Screens—A Case Study of Inertial Vibrator Bearing Failure in Calcium Carbonate Production Plant
Publication -
Mixed mechanical-metrological approach to quantify the fractographic damage in mechanical components subjected to cyclic loading
Publication -
Synthesis, biological activity and conformational analysis of head-to-tail cyclic analogues of LL37 and histatin 5
Publication -
Crystal structures of eight- and ten-membered cyclic bisanisylphosphonothioyl disulfanes and comparison with their P-ferrocenyl analogues
PublicationTwo new crystal structures of eight- and ten-membered cyclic bisanisylphosphonothioyl disulfanes, namely 2,5-bis(4-methoxyphenyl)-1,6,3,4,25,55- dioxadithiadiphosphocane-2,5-dithione, C16H18O4P2S4, and 2,5-bis(4-methoxyphenyl)-1,6,3,4,25,55-dioxadithiadiphosphecane-2,5-dithione, C18H22O4P2S4, have been determined and compared to structures of the ferrocenyl analogues. The eight-membered rings have similar conformations (TBC) but...
-
Electrochemical behaviour of Cr coating in acidic sulphate solution studied by cyclic polarization and impedance spectroscopy
PublicationOdporność korozyjną powłok chromowych w 0.01 M H2SO4 zbadano metodami woltamperometrii cyklicznej i spektroskopii impedancyjnej. Stwierdzono, że właściwości ochronne powłoki chromowej w kontakcie z powietrzem wzrastają dzięki tworzeniu się warstwy tlenkowej zapełniającej defekty w powłoce. W trakcie polaryzacji anodowej następuje częściowe roztwarzanie tej warstwy i penetracja agresywnego środowiska do podłoża (stali), co powoduje...
-
COMMENTS ON EXISTING ANALYTICAL SOLUTIONS TO THE WAVE-INDUCED CYCLIC RESPONSE OF A POROUS SEABED OF INFINITE THICKNESS
PublicationThis paper deals with the wave-induced cyclic response of a porous seabed (by means of oscillating parameters: pore-fluid pressure, soil displacement components, effective normal stress and shear stress components) due to a surface sinusoidal water-wave propagating over a seabed of infinite thickness. The main existing analytical solutions to the governing problem are critically discussed, pointing out their meaningful errors and...
-
Importance of sign conventions on analytical solutions to the wave-induced cyclic response of a poro-elastic seabed
PublicationThis paper discusses the influence of different sign conventions for strains and stresses, i.e. the solid mechanics sign convention and the soil mechanics sign convention, on the form of governing partial differential equations (the static equilibrium equations and the continuity equation) used to describe the wave-induced cyclic response of a poro-elastic seabed due to propagation of a sinusoidal surface water-wave. Some selected...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Modeling of a cyclic plane strain compression-extension test in granular bodies within a polar hypoplasticity
PublicationW artykule przedstawiono wyniki numerycznej analizy wpływu cyklicznego ściskania-rozciągania na lokalizację odkształceń stycznych w materiałach granulowanych. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. Analizę przeprowadzono dla piasku zagęszczonego i luźnego dla różnych amplitud obciążenia.
-
Cyclic Behavior of Masonry Shear Walls Retrofitted with Engineered Cementitious Composite and Pseudoelastic Shape Memory Alloy
PublicationThe behavior of masonry shear walls reinforced with pseudoelastic Ni–Ti shape memory alloy (SMA) strips and engineered cementitious composite (ECC) sheets is the main focus of this paper. The walls were subjected to quasi-static cyclic in-plane loads and evaluated by using Abaqus. Eight cases of strengthening of masonry walls were investigated. Three masonry walls were strengthened with different thicknesses of ECC sheets using...
-
Reversible Data Hiding in Encrypted DICOM Images Using Cyclic Binary Golay (23, 12) Code
PublicationIn this paper, a novel reversible data hiding method for encrypted images (RDHEI) is proposed. An efficient coding scheme based on cyclic binary Golay (23, 12) code is designed to embed additional data into the least significant bits (LSBs) of the encrypted image. The most significant bits (MSBs) are used to ensure the reversibility of the embedding process. The proposed scheme is lossless, and based on the receiver’s privileges,...
-
99mTc-Galacto-RGD2: A Novel 99mTc-Labeled Cyclic RGD Peptide Dimer Useful for Tumor Imaging
PublicationThis study sought to evaluate [99mTc(HYNIC-Galacto-RGD2)-(tricine)(TPPTS)] (99mTc-Galacto-RGD2: HYNIC = 6-hydrazinonicotinyl; Galacto-RGD2 = Glu[cyclo[Arg-Gly-Asp-D-Phe-Lys(SAA-PEG2-(1,2,3-triazole)-1-yl-4-ethylamide)]]2 (SAA = 7-amino-L-glycero-L-galacto-2,6-anhydro-7-eoxyheptanamide, and PEG2 = 3,6-dioxaoctanoic acid); and TPPTS = trisodium triphenylphosphine-3,3',3''-trisulfonate) as a new radiotracer for tumor imaging. Galacto-RGD2...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublicationIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
FE-modeling of shear resistance degradation in granular materials during cyclic shearing under CNS condition
PublicationW artykule przedstawiono wyniki numerycznej analizy degradacji wytrzymałości na ścinanie w materiałach granulowanych podczas cyklicznego ścinania z warunkiem stałej sztywności normalnej. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego modelu hipoplastycznego.
-
Application of enhanced elasto-plastic damage models to concrete under quasi-static and dynamic cyclic loading
PublicationArtykuł omawia wyniki symulacji zachowania sie elementów betonowych poddanych zginaniu w czasie cyklicznego obciążenia. Do symulacji zastosowano 3 połączone modele sprężysto-plastyczne z degradacją sztywności i z nielokalnym osłabieniem. Wyniki symulacji porównano bezpośrednio z doświadczeniami.
-
Hat problem on odd cycles
PublicationThe topic is the hat problem in which each of n players is randomly fitted with a blue or red hat. Then everybody can try to guess simultaneously his own hat color by looking at the hat colors of the other players. The team wins if at least one player guesses his hat color correctly, and no one guesses his hat color wrong; otherwise the team loses. The aim is to maximize the probability of a win. In this version every player can...
-
Methods of Cyclist Training in Europe
PublicationThe following study aims to address the issue of cyclist training methodologies. Recent European bicycle accident statistics reveal a troubling upward trend. A potential solution to mitigate such incidents involves providing cyclists with comprehensive training encompassing traffic regulations and interactions with fellow road users. We conducted a comparative analysis of the cycling education approaches and cyclist training systems...