Filters
total: 1710
filtered: 1398
displaying 1000 best results Help
Search results for: RESIDUAL REMOVAL
-
The efficiency of biological nutrients removal in WWTP`s "Wschód" in Gdańsk (Poland)
PublicationRozbudowana w latach 1997-99 oczyszczalnia ścieków Wschód w Gdańsku zapewnia wysokoefektywne oczyszczanie ścieków odprowadzanych do wód Zatoki Gdańskiej Morza Bałtyckiego. Zrealizowany układ technologiczny biologicznego oczyszczania ścieków o przepustowości 180 tys. m3 na dobę jest złożony z sześciu reaktorów MUCT, z których każdy współpracuje z dwoma osadnikami wtórnymi. W artykule podsumowano okres pierwszych trzech lat eksploatacji...
-
Magnetic superhydrophobic melamine sponges for crude oil removal from water
PublicationThis paper proposes the preparation of a new sorbent material based on melamine sponges (MS) with superhydrophobic, superoleophilic, and magnetic properties. This study involved impregnating the surface of commercially available MS with eco-friendly deep eutectic solvents (DES) and Fe3O4 nanoparticles. The DES selection was based on the screening of 105 eutectic mixtures using COSMO-RS modeling. Other parameters affecting the efficiency...
-
Chromium (III) removal by perennial emerging macrophytes in floating treatment wetlands
PublicationFloating treatment wetlands (FTWs) are a sustainable solution to treat polluted water, but their role in chromium (Cr(III)) removal under neutral pH conditions remains poorly understood. This study evaluated the potential of FTWs planted with two perennial emergent macrophytes, Phragmites australis and Iris pseudacorus, to remove Cr(III) and nutrients (N and PO4-P) from water containing 7.5 mg/L TN, 1.8 mg/L PO4-P, and Cr(III)...
-
Advanced oxidation processes for the removal of mono and polycyclic aromatic hydrocarbons – A review
PublicationAromatic hydrocarbons (AHs) are toxic environmental contaminants presented in most of the environmental matrices. Advanced oxidation processes (AOPs) for the removal of AHs in the account of complete mineralization from various environmental matrices have been reviewed in this paper. An in-depth discussion on various AOPs for mono (BTEX) and polyaromatic hydrocarbons (PAHs) and their derivatives is presented. Most of the AOPs were...
-
Combined partial denitrification/anammox process for nitrogen removal in wastewater treatment
PublicationRecently, the combined partial denitrification and anammox (PD/anammox) has received special attention as a viable alternative for N removal using organic matter present in municipal wastewater. In comparison with conventional nitrification-denitrification, PD/anammox provides enormous opportunities to achieve sustainable wastewater treatment due to the lack of dissolved oxygen (DO) demand, a smaller amount of organic carbon (C)...
-
Organic matter removal efficiency in treatment wetlands simulation by COD fractions
PublicationThe objective of this paper was to investigate the organic fraction (colloidal, particulate, and dissolved) in sewage treatment in treatment wetland. Performance of TWs was simulated well with a simple first order model k – C* based on monitoring data. In this investigation background or residual concentration (C*) was assumed to be equal concentration of input influent organic matter in particulate (CODp). Calculated reaction...
-
Treatment strategies for comorbid conditions lower residual risk in patients with treated hypertension: FOURIER and other randomized outcome trials
Publication -
Analysis by the Residual Method for Estimate Market Value of Land on the Areas with Mining Exploitation in Subsoil under Future New Building
Publication -
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublicationWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Determination of metronidazole residues in water, sediment and fish tissue samples
Publication -
Sample preparation techniques for determination of pesticide residues in food samples
PublicationPesticides are very important in increasing the efficiency and quality of agricultural production. They are applied in many spheres of life, not only in agriculture, and their applications are expanding. Despite their numerous merits, pesticides are some of the most toxic substances contaminating our environment and have a negative impact on the human health. Properties of pesticides such as stability, ability to bioaccumulation...
-
Copper binding by the cystatin C fragment. The role of histidine residues
Publication -
Study of the effect of residues of pharmaceuticals on the environment on the example of bioassay Microtox®
PublicationResidues of pharmaceuticals present in the aqueous environment can be found in a mixture of different substances wherein drugs not remain inert with respect to each other. In such mixtures a phenomenon of synergism or antagonism may occur, which can contribute to increase or decrease the overall toxicity of the mixture of drugs. Pharmaceuticals namely: diclofenac (sodium salt), oxyteracycline hydrochloride, fluoxetine hydrochloride,...
-
High-speed fpga pipelined binary-to-residue converter
Publicationw pracy przedstawiono architekturę przepływowego konwertera z systemu z uzupełnieniem do 2 z systemu binarnego. zastosowano segmentację słowa wejściowego ze wstępną inwersją dla liczb ujemnych. reszty liczb reprezentowanych przez poszczególne segmenty są obliczane poprzez odczyt z pamięci adresowanej binarną reprezentacją segmentu. otrzymane reszty sumowane są w wielooperandowym sumatorze modulo z korekcją reszty dla liczb ujemnych.pracę...
-
Implementation of discrete convolution using polynomial residue representation
PublicationConvolution is one of the main algorithms performed in the digital signal processing. The algorithm is similar to polynomial multiplication and very intensive computationally. This paper presents a new convolution algorithm based on the Polynomial Residue Number System (PRNS). The use of the PRNS allows to decompose the computation problem and thereby reduce the number of multiplications. The algorithm has been implemented in Xilinx...
-
improved noniterative residue division for small number ranges
Publicationw pracy zaprezentowano multiplikatywny algorytm dzielenia w systemie resztowym i projekt 12-bitowego dzielnika dla modułów 5-bitowych. w algorytmie zastosowano obliczanie przybliżonej odwrotności dzielnika i mnozenie przez dzielną. binarna reprezentacja dzielnika jest dekomponowana na dwa segmenty 6-bitowe, co umożliwia obliczenie w środowisku fpga poprzez odwzorowanie realizowane jako odczyt pamięci. w pracy podano udoskonalony...
-
Implementation of discrete convolution using polynomial residue representation
Publication -
Residue-to-two's complement converter based on core function
PublicationW artykule przedstawiono układową realizację konwertera z systemu resztowego do systemu binarnego bazującego na funkcji jądra. Zastosowanie funkcji jądra powoduje zmniejszenie wymagań sprzętowych przy realizacji konwertera. W publikacji omówiono problem dektekcji znaku oraz realizacje ukłądową konwertera w środowisku FPGA.
-
FPGA realization of the high-speed binary-to-residue converter
Publicationprzedstawiono architekturę i realizację w technologii fpga konwertera z systemu binarnego do systemu resztowego. algorytm konwertera oparty jest na podziale słowa wejściowego na segmenty 4-bitowe i następnie obliczeniu reszty liczby reprezentowanej przez dany segment, sumowaniu binarnym przy zastosowaniu csa i redukcji modulo w układzie dwuoperandowego sumatora modulo.
-
Effective residue-to-binary converter with the Chinese Remainder Theorem
PublicationKonwersja liczb z systemu resztowego do systemu binarnego jest podstawową operacją we wszystkich układach cyfrowego przetwarzania sygnałów, które wykorzystują system resztowy. W niniejszej pracy zaproponowano nową metodę konwersji opartą o chińskie twierdzenie o resztach dla modułów 5- i 6-bitowych. Specyficzną cechą nowej metody jest sposób obliczania tzw. współczynnika nadmiaru w formule chińskiego twierdzenia o resztach, co...
-
Complex multiplier based on the polynomial residue number system
PublicationPrzedstawiono próbę zaprojektowania mnożnika zespolonego 4x4 opartego na algorytmie Skavantzosa i Stouraitisa. W algorytmie stosuje siękodowanie liczb n-bitowych jako wielomianów stopnia 7 w pierścieniu wielomianów modulo (x^8-1) z n/4-bitowymi współczynnikami. Mnożenie zespolone jest wykonywane jako 8-punktowy splot cykliczny. Podanoopóżnienie i złożoność sprzętową jak również porównanie ze standardowym.rozwiązaniem.
-
High-speed binary-to-residue converter with improved architecture.
PublicationPrzedstawiono ulepszoną architekturę szybkiego konwertera liczb z systemu binarnego do systemu resztowego dla liczb ze znakiem w kodzie U2. Algorytm konwertera oparty jest o segmentację słowa wejsciowego nasegmenty 4-bitowe. Reszty liczb reprezentowanych przez segmenty sąobliczane poprzez odwzorowanie. Wielooperandowe sumowanie modulo jest realizowane przy użyciu drzewa Wallace'a z segmentacją wektorów wyjściowych oraz finalnego...
-
Computation of the convolution with use of the polynomial residue number system.
PublicationPrzedstawiono użycie wielomianowych systemów resztowych do obliczania splotu w cyfrowych układach dużej skali integracji VLSI.
-
Chromogenic azomacrocycles with imidazole residue: Structure vs. properties
PublicationNew diazo macrocycles linked by hydrocarbon chain bearing imidazole or 4-methylimidazole residue have been synthetized with satisfactory yield (24–55%). The structure of macrocycles was confirmed by X-ray analysis and spectroscopic methods (1H NMR, MS, FTIR). Metal cation complexation studies were carried out in acetonitrile and acetonitrile-water system. It was found that azomacrocyles form triple-decker complexes with lead(II)....
-
Advanced oxidation processes for recalcitrant compounds removal comparison with biofiltration by Corbicula fluminea
Publication -
Removal efficiency of phenol by ozonation process with calcium peroxide from aqueous solutions
Publication -
Impact of enhanced pretreatment on biological nutrient removal in municipal wastewater treatment plants
PublicationThe aim of this study was to determine the effect of enhanced primary treatment on: increasing primary sludge production for increased biogas production; reducing the organic load on downstream biological treatment processes and thereby reducing energy consumption for aeration; denitrification and enhanced biological phosphorus removal (EBPR) rates in the activated sludge system. For this purpose, three commercial organic polymers...
-
Influence of composition of raw wastewater on removal of nitrogen compounds in multistage treatment wetlands
PublicationInfluence of composition of raw wastewater on the efficiency of organic matter and nitrogen removal in multistage treatment wetlands has been examined. Commonly used indicators, like COD/BOD5 and BOD5/TN ratio, determining wastewater susceptibility to biodegradation in conventional treatment technologies were assessed. It was confirmed that multistage treatment wetland may be used for treatment of wastewater with high loads of...
-
Removal of hydrophobic organic pollutants from soil by surfactants and biosurfactants solution flushing
PublicationPrzedstawiono wyniki solubilizacji dwóch związków hydrofobowych - tetrachloroetylenu i dodekanu oraz dwóch bazowych olejów mineralnych - SAE 30/95 i PAO6 w wodnych roztworach syntetycznych związków powierzchniowo czynnych oraz biosurfaktantów. Zaobserwowano liniowy wzrost solubilizacji wraz ze wzrostem stężenia surfaktantu.Przedstawiono także wyniki wymywania oleju PAO6 ze sztucznie zaolejonego piasku (w kolumnie) z pomocą roztworów...
-
The solubilization of hydrocarbon mixtures as one of the mechanisms of hydrophobic pollutants removal from soil
PublicationBadano solubilizację mieszanin węglowodorów alifatycznych (dekanu, dodekanu, tetradekanu, heksadekanu) i aromatycznych (toluenu, o-xylenu) w roztworach micelarnych surfaktantów niejonowych - oksyetylenowanego alkoholu (Rokanol NL6) i alkilopoliglukozydów (Triton BG10, AG 6210). Najwyższą efektywność solubilizacji uzyskano dla Rokanolu NL6. Efektywność solubilizacji mieszaniny zależała od rozpuszczalności poszczególnych jej składników...
-
Removal of organic compounds from water by solvent sublation. Criteria for solvent selection.
PublicationProces flotoekstrakcji zastosowano do usuwania z wody następujących związków organicznych: tetrachlorku węgla, chloroformu, 1,3,5-trimetylobenzenu (mezytylenu), fenolu i 2,4,5-trichlorofenolu. Jako odbierające fazy organiczne użyto: olej mineralny, 1-dekanol, 1-oktanol, octan amylu, dodekan i tetradekan. Mechanizmem decydującym o usuwaniu lotnych związków organicznych (VOC) było odparowanie do wnętrza pęcherzyków gazu, podczas...
-
A sumanene-containing magnetic nanoadsorbent for the removal of caesium salts from aqueous solutions
Publication -
The effectiveness of organic matter removal in unit processes of the technological groundwater treatment system
Publication -
Removal of metal particles from carbon nanotubes using conventional and microwave methods
Publication -
An activation-free route to porous magnetic carbon adsorbents for the removal of phenolic compounds
Publication -
The role of particulate and colloidal substrate in biological nutrient removal activated sludge systems
PublicationThe authors investigated COD fractionation according to the physical state (soluble/colloidal/particulate) in four wastewater treatment plants (WWTPs) in northern Poland. It was found that particulate and colloidal organic compounds constituted up to 70% of total COD. On the other hand, according to literature data, municipal wastewater contains readily and slowly biodegradable substrates in the amount of approximately 10-30% and...
-
Assessment of metal removal in a surface flow constructed wetland treating landfill leachate
PublicationThe study concerns heavy metal retention and transformation processes in a free water surface constructed wetland treating landfill leachate in a temperate climate. The total effectiveness of heavy metals removal in the analyzed CW was evaluated basing on heavy metals inflow and outflow concentrations. The concentrations of eight heavy metals (Fe, Mn, Zn, Pb, Ni, Cu, Cr, Cd) in landfill leachate (LL) and sediments were measured....
-
Impact of influent wastewater quality on nitrogen removal rates in multistage treatment wetlands
PublicationNitrogen removal in treatment wetlands is influenced by many factors, and the presence of electron donors (biodegradable organic matter) and electron acceptors (nitrate ions) is the main limiting one; for obtaining these conditions, multistage treatment wetlands (MTWs) are required, where an extensive nitrification can be obtained in the first stages under aerobic conditions leaving then to the following anoxic/anaerobic stages...
-
Oil removal from polluted soil by washing with surfactants solutions in dynamic conditions
PublicationFor washing of the oil from polluted soil surfactants solutions were applied. In a research a nonionic synthetic surfactant - polyoxyethylene ether of synthetic fatty alcohol (Rokanol NL6), rhamnolipid biosurfactant JBR 425 (Jeneil Biosurfactant Co. LLC) and their mixtures were used. Results of oil removal from peat soil and sand with mixtures of surfactants solutions at concentration 0,5 g/dm...
-
Removal efficiency of phenol by ozonation process with calcium peroxide from aqueous solutions
PublicationPhenol has been introduced as a priority pollutant by the US Environmental Protection Agency. Advanced oxidation processes (AOPs) are one of the most efcient methods for removal of non-degradable organic pollutants in aqueous solutions. The removal efciencies of phenol and COD under optimal conditions pH=3, phenol concentration=5 mg/L, CaO2 concentration=0.025 mg/L, temperature 25 °C, 1 g/min ozonation rate and contact time=90...
-
Functionalized nanodiamonds as a perspective green carbo-catalyst for removal of emerging organic pollutants
PublicationRapid industrial and urban development jointly with rising global population strongly affect the large-scale issues with drinking, groundwater, and surface water pollution. Concerns are not limited to environmental issues but also human health impact becoming serious global aspect. Organic pollution becomes a primarily serious hazard, therefore, the novel sophisticated approaches to treat them are thoroughly investigated. Among...
-
Recent Advancements in Cyclodextrin-Based Adsorbents for the Removal of Hazardous Pollutants from Waters
PublicationWater is an essential substance for the survival on Earth of all living organisms. However, population growth has disturbed the natural phenomenon of living, due to industrial growth to meet ever expanding demands, and, hence, an exponential increase in environmental pollution has been reported in the last few decades. Moreover, water pollution has drawn major attention for its adverse effects on human health and the ecosystem....
-
Modelization of Nutrient Removal Processes at a Large WWTP Using a Modified ASM2d Model
PublicationThe biodegradation of particulate substrates starts by a hydrolytic stage. Hydrolysis is a slow reaction and usually becomes the rate limiting step of the organic substrates biodegradation. The objective of this work was to evaluate a novel hydrolysis concept based on a modification of the activated sludge model (ASM2d) and to compare it with the original ASM2d model. The hydrolysis concept was developed in order to accurately...
-
A Simplified Method of Trend Removal to Determine Noise Observed During a Supercapacitor’s Discharging
PublicationIn this paper, new method of trend removal is proposed. This is a simplified method based on Empirical Mode Decomposition (EMD). The method was applied for voltage time series observed during supercapacitor discharging process. It assured the determination of an additive noise component after subtracting the identified trend component. We analyzed voltage time series observed between the terminals of the supercapacitor when discharged...
-
Use of pyridinium and pyrrolidinium ionic liquids for removal of toluene from gas streams
PublicationSeparation of toluene from a toluene/N2 gas mixture using supported liquid membranes based on a series of pyridinium (1-butylpyridinium- bis(trifluoromethylsulfonyl)imide - [C4Py][Tf2N], 1-hexylpyridinium trifluoromethanesulfone [C6Py][Tf2N]) and pyrrolidinium (1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide - [C4Pyrr][Tf2N], 1-hexyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide - [C6Pyrr][Tf2N], 1-butyl-1-methylpyrrolidinium...
-
Kinetics of pollutants removal in vertical and horizontal flow constructed wetlands in temperate climate
PublicationThis paper reports a comparative study on kinetics of organic matter expressed as BOD5 and nitrogen removal in constructed wetlands operated in Poland. Analyzed data were collected at eight wetland systems, composed of subsurface flow beds: horizontal flow (HF) and vertical flow (VF), in different number and sequences. The analysis involved particularly mass removal rates (MRR) and first-order removal rate coefficients of BOD5...
-
Effectiveness of pollutants removal in hybrid constructed wetlands – different configurations case study
PublicationIn recent years, an increase in interest in hybrid constructed wetland systems (HCWs) has been observed. The aim of the paper is to compare different HCW configurations in terms of mass removal rates and efficiency of pollutants removal. Analysed data have been collected at multistage constructed wetlands in Poland, which are composed by at least two beds: horizontal subsurface flow (SSHF) and vertical subsurface flow (SSVF). The...
-
Influence of COD-fractions on removal effectiveness and accumulation of organic matter in constructed wetlands
PublicationW pracy wykazano, że efektywność usuwania substancji organicznej doprowadzanej w ściekach bytowo-gospodarczych do złóż hydrofitowych zależy od rodzaju frakcji substancji organicznej oraz ich stężeń. Na podstawie analizy poszczególnych frakcji ChZT (rozpuszczonych związków organicznych biologicznie łatwo- i nierozkładalnych oraz zawiesin organicznych biologicznie wolno- i nierozkładalnych) wykazano, że na akumulację substancji organicznej...
-
Dependence between quality and removal effectiveness of organic matter in hybrid constructed wetlands
PublicationW procesie oczyszczania ścieków w Vertical Flow Constructed Wetland (VF-CW) jednym z czynników jest dopływ tlenu. Niewystarczający dopływ tlenu do złoża może być przyczyną braku efektywności usuwania zanieczyszczeń, a więc wskazywać na niewłaściwą eksploatację obiektu.Obiekty badań stanowiły złoża pionowe stanowiące jeden z elementów biologicznego oczyszczania dwóch hybrydowych systemów hydrofitowych zlokalizowanych w Wieszynie...