Filters
total: 1029
filtered: 899
-
Catalog
Chosen catalog filters
Search results for: TURBINE 18K370
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublicationThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Assessment of damage causes of a 17 m long wind turbine blade model
PublicationThe subject matter is to verify the stiffness of the steel supporting structure and assess the causes of cracks in the 17 m long wind turbine blade model
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublicationThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Application of spatial neural simulators of turbine blade rows to fluid flow diagnostics
PublicationThis chapter presents the results of neural modelling of fluid flow in steam turbine row. In modelling working conditions of the flow channel varied, thus the aim of the work was to reconstruct the reference state - distributions of velocity, pressure, and losses in flow channel - with high accuracy for fluid flow diagnostics.
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublicationPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Numbers, Please: Power- and Voltage-Related Indices in Control of a Turbine-Generator Set
PublicationThis paper discusses the proper selection and interpretation of aggregated control performance indices values mirroring the quality of electrical energy generation by a turbine-generator set cooperating with a power system. Typically, a set of basic/classical and individual indices is used in energy engineering to ensure the mirroring feature and is related to voltage, frequency and active or reactive power deviations from their...
-
Influence of the steam within seals and glands of the turbine on its rotor motion stability.
PublicationPrzedstawiono metodę obliczania charakterystyk dynamicznych wpływu parowych uszczelnień turbin na ich dynamikę i stateczność ruchu wirników. Zarysowano model ''masowy'' uszczelnienia. Podano przykłady zastosowań.
-
Aerodynamic excitations generated in turbine shroud clearance determined bymeans of neural networks
PublicationSiły aerodynamiczne generowane w uszczelnieniach turbinowych z reguły opisywane są modelem liniowym. Przy dużych drganiach wirnika sposób ten daje niezbyt dokładne wyniki. Zaproponowano wykorzystanie sieci neuronowych do określania sił ciśnieniowych powstających w uszczelnieniu. Wyniki porównano z badaniami eksperymentalnymi.
-
Identification of inertia, damping and stiffness parameters for low pressure steam turbine framework.
PublicationW pracy przedstawiono metodę identyfikacji masy tłumienia i sztywności kadłuba części niskoprężnej turbiny parowej 200MW.
-
Unsteady aerodynamic forces acting on the rotor blades in the turbine stagewith steam extraction.
PublicationPrzeprowadzono analizę niestacjonarnych wymuszeń działających na łopatki wirnikowe w stopniu z upustem turbiny 13UC100. Niestacjonarne siły zostały wyznaczone dla 4 punktów pracy upustu. Wskazano na możliwą przyczynę zaistniałego zniszczenia łopatek wirnikowych turbiny.
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublicationThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Steam turbine as the main ship propulsion. More than a hundred years at sea.
PublicationPrzedstawiono rys historyczny rozwoju okrętowych turbin parowych. Omówiono główne rozwiązania konstrukcyjne podstawowych elementów parowych siłowni turbinowych i współczesne tendencje i perspektywy rozwoju tego napędu.
-
Propozycja modyfikacji struktury regulatorów turbin parowych
PublicationReferat podejmuje tematykę wpływu struktury regulatora turbiny na proces obrony i odbudowy systemu elektroenergetycznego. Wskazując niedoskonałości obecnie stosowanych regulatorów zaproponowano autorską strukturę regulatora turbiny parowej. Nowy regulator wykorzystuje zalety stosowanych obecnie regulatorów mocy z korektą od częstotliwości, pozwalając jednocześnie na efektywniejsze sterowanie turbinami w stanach awaryjnych, przy...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
Nonlinear Cointegration Approach for Condition Monitoring of Wind Turbines
Publication -
Obliczenia rozpływu powietrza chłodzącego w turbinie gazowej
PublicationOptymalizacja spełnia ważną funkcję, pozwala nam zminimalizować straty poniesione poprzez zastosowanie chłodzenia. Głównym celem artykułu była optymalizacja rozpływu powietrza chłodzą-cego tak aby zminimalizować straty mocy spowodowane podziałem strumienia powietrza, takie dobranie upustów w sprężarce aby moc w turbinie była jak największa, a moc sprężarki jak najmniejsza. W artykule zawarto model obliczeń, przedstawiono podstawowy...
-
Steam turbines governors in power system restoration process
PublicationThe paper discusses problems related to electric power system restoration process. The turbine controller operating mode influence in small subsystem is analyzed. There are considered abilities, advantages and drawbacks of the controller's two operating modes: power control and speed (frequen-cy) control, to rebuild electric power system from a single generating unit to a few parallel running generators.
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublicationThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublicationThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Stopień z upustem - analiza stacjonarna turbiny 13K215
PublicationW pracy przedstawiono analizę przepływu w obszarze stopnia turbiny parowej z upustem 13K215 przed modernizacją. Zaproponowano model umożliwiający taką analizę. W wyniku analizy uzyskano dystrybucje ciśnienia w kierunku obwodowym, co pozwala na określenie sił działających na łopatki wirnikowe, pracujacych w obszarze nierównomierności generowanych przez upust.
-
Hydrodynamic journal bearing - ''Y'' particularly for steam turbines.
PublicationW artykule przedstawiono koncepcję i zasadę działania nowego, ślizgoweo łożyska poprzecznego typu ''Y''. Przedstawiono wady i zalety nowego rozwiązania. Porównano charakterystyki dynamiczne i statyczne klasycznego łożyska cytrynowego (soczewkowego) z nowym łożyskiem ''Y''.Podano przykładowe wdrożenia i ich efekty.
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publication -
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublicationResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Spectral Finite Element Method for Propagation of Elastic Waves in Wind Turbine Blades for SHM
PublicationW pracy przedstawiono model łopaty turbiny wiatrowej zbudowany z wykorzystaniem spektralnych elementów skończonych. Omówiono wyniki symulacji propagacji fal sprężystych i ich interakcji z uszkodzeniami w formie pęknięcia i delaminacji.
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
Changing the Ship Propulsion System Performances Induced by Variation in Reaction Degree of Turbocharger Turbine
PublicationArtykuł przedstawia szczegółowy model matematyczny układu napędu statku obejmującego: wolnoobrotowy silnik spalinowy okrętowy, śruba okrętowa oraz regulator prędkości kątowej. Model ten, następnie jest wykorzystany do badania symulacyjnego zachowania układu zarówno w stanach ustalonych jak i nieustalonych. Model jest zweryfikowany z wynikami eksperymentalnymi. Przedstawienie oryginalnej metody oceny wrażliwości układu względem...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Wind resource assessment and energy yield prediction for the small wind turbine on the Szubieniczne Hill
PublicationThe goal of this study is to preliminary assess the wind resources on the Szubieniczne Hill in order to predict the annual energy production for planned small wind turbine. The analyzed site is located close to the Gdańsk University of Technology campus, in complex urban environment additionally surrendered by forested hills. The assessment is based on Computational Fluid Dynamics simulations which allow to evaluate the wind energy potential...
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublicationCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublicationThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Some problems of self-excited vibrations of turbine rotors. Part I: The theoretical method
PublicationPrzedstawiono teoretyczną metodę określania uszczelnienia nadbandażowego lub dławicy zupełnej, które odgrywa największą rolę w generowaniu samowzbudnych drgań typu aerodynamicznego wirników turbinowych. Drgania harmoniczne układu wirnika turbiny opisane są macierzowym równaniem, a wymuszenia aerodynamiczne określane metodą współczynników wpływu.
-
Research into flows in turbine blade seals. Part III: Numerical calculations versus experiment
PublicationPrzedstawiono wyniki badań doświadczalnych przepływów w uszczelnieniu nadbandażowym stopnia turbinowego, przeprowadzonych na powietrznej turbinie modelowej. Rezultaty te porównano z wynikami badań numerycznych z zastosowaniem programu Fluent.
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublicationThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublicationOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Complementary studies of residual stress distribution of repaired power plant steam turbine casing
PublicationRozkład i poziom naprężeń własnych w korpusach turbin badano za pomocą efektu Barkhausena oraz metodą nawiercania otworów. Badano również twardość. Korpusy były reperowane metodą zaspawania. Wykazano, iż zastosowana technologia nie wprowadza naprężeń o poziomie zagrażającym dalszej ekploatacji korpusu.
-
Analiza sposobów chłodzenia układów łopatkowych turbin gazowych
PublicationReferat stanowi analizę najczęściej spotykanych sposobów chłodzenia układów łopatkowych w turbinach gazowych. W artykule przedstawiono schematy ilustrujące sposób chłodzenia a tak że przepływ strumienia słodzącego w układzie łopatkowym. Uwagę poświęcono głównie układom bez wymuszenia czyli konwekcyjnym.
-
ANALIZA PARAMETRÓW PRZEPŁYWOWYCH PRZEZ STOPNIE TURBIN PAROWYCH
PublicationTurbina w obiegach cieplnych pracuje w zmienionych warunkach. Dodatkowo zmianie ulegają strumienie mas czynnika roboczego z powodu chłodzenia (w turbinach gazowych) lub poboru pary do układu regeneracji ciepła (w turbinach parowych). Te dopływy i pobory również zależą od obciążenia turbozespołu. Stąd w obliczeniach numerycznych wieńców wirnikowych dla wyznaczenia stanów referencyjnych, podobnie jak dla turbin gazowych, trzeba uwzględnić...
-
Rynek turbin i silników gazowych na świecie.
PublicationW artykule przedstawiono światowe tendencje w zakresie instalacji turbin i silników gazowych oraz omówiono najważniejsze czynniki związane z szerszym wykorzystaniem gazu ziemnego w energetyce. Zwrócono uwagę na wzrost zainteresowania układami skojarzonymi oraz energią odnawialną.
-
SYSTEM RADIOLOKALIZACYJNY OPARTY NA FARMIE TURBIN WIATROWYCH
PublicationW referacie zaproponowano wykorzystanie farmy turbin wiatrowych do budowy systemu radiolokalizacyjnego dla obiektów latających (samolotów). Zaproponowane rozwiązanie umożliwia oszacowanie położenia obiektu w przestrzeni, zwłaszcza w ruchu, za pomocą sygnałów lokalizacyjnych nadawanych asynchronicznie z wież turbin wiatrowych. Przedstawiono matematyczną analizę metody oraz wyniki badań symulacyjnych efektywności pracy rozwiązania...
-
Turning ability of hydrofoil crafts
PublicationPrzedstawiono metodę pozwalającą wyznaczać średnicę taktyczną, kąt przechyłu i kąt dryfu oraz siłę poprzeczną na sterze podczas ustalonej cyrkulacji wodolotu. W tym celu opracowano układ równań opisujących ruch wodolotu w płaszczyźnie poziomej. Współczynniki równań są wyznaczane na podstawie głównych parametrów geometrycznych jednostki oraz płatów. Przeprowadzono także szereg obliczeń dla różnych konfiguracji płatów oraz zespołu...
-
Analysis of operations of combined STIG installation
PublicationSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
Cointegration Modelling for Health and Condition Monitoring of Wind Turbines - An Overview
Publication -
Operational Condition Monitoring of Wind Turbines Using Cointegration Method
Publication -
Design and numerical study of turbines operating with MDM as working fluid
Publication -
Wzrost sprawności turbiny gazowej przez zastosowanie idei Szewalskiego
PublicationW artykule przedstawiono wpływ zastosowania upustu na sprawność turbiny gazowej. Upust w turbinie zrealizowano według idei prof. Roberta Szewalskiego, która polega na zastosowaniu upustu międzystopniowego w turbinie gazowej do podgrzewu powietrza zasilającego komorę spalania. Dzięki przeprowadzonej modyfikacji osiąga się wzrost sprawności obiegu oraz spadek zużycia paliwa. Analiza numeryczna obiegu cieplnego przed i po modernizacji...
-
Turbiny wiatrowe o pionowej osi obrotu - wirnik Savoniusa
PublicationReferat stanowi krótki przegląd turbin wiatrowych o osi pionowej, ze szczególnym uwzględnieniem wirnika Savoniosa. Głównym celem artykułu jest poznanie różnych wariantów, w jakich występuje wirnika Savoniosa oraz znalezienie najsprawniejszego typu. Z licznych możliwości modyfikacji owego wirnika jako pierwsza została zaprezentowana opcja ze zmiennymi końcówkami turbiny. Przepływ przez szczelinę międzyłopatkową będzie wybrany jako...
-
Wyznaczenie maksymalnej sprawności obiegu zeroemisyjnej turbiny gazowo-parowej
PublicationW pracy omówiono koncepcję zeroemisyjnej turbiny gazowo-parowej z zastosowaniem oksyspalania
-
Optymalizacja rozpływu strumienia powietrza chłodzącego w turbinie gazowej
PublicationOptymalizacja spełnia ważną funkcję, pozwala nam zminimalizować straty poniesione poprzez zastosowanie chłodzenia. W wystąpieniu wykazano słuszność i celowość chłodzenia turbiny gazowej. Głównym celem prezentacji wyników było optymalizowanie rozpływu powietrza chłodzącego tak aby zminimalizować straty mocy spowodowane podziałem strumienia powietrza, takie dobranie upustów w sprężarce aby moc w turbinie była jak największa, a moc...