Search
Filters
total: 1186
filtered: 972
Search results for: CALLULAR CONCRETE
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
A constitutive law for concrete with smooth transition from continuous into discontinuous cracks’ description
PublicationPaper presents a constitutive model for concrete that combines a continuous and discontinuous crack’s description to simulate the concrete under tensile dominated loads. In a continuum regime, two different constitutive laws were used. First, a plasticity model with the Rankine failure criterion and an associated flow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. Both model alternatives...
-
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension.
PublicationW artykule przedstawiono wyniki numerycznej obliczenia rozstawu rys w pręcie żelbetowym poddanemu rozciąganiu. Obliczenia wykonano przy zastosowaniu sprężysto-plastycznego modelu rozszerzonego o długość charakterystyczna mikrostruktury przy pomocy teorii nielokalnej.
-
Effect of aggregate structure on fracture process in concrete using 2D lattice model
PublicationArtykuł przedstawia symulacje rys w betonie przy zastosowaniu nowego modelu siatkowego. Zbadano wpływ rozkładu i wielkości kruszywa oraz wpływ strefy kontaktu na nośność i propagacje rys. Obliczenia były dwuwymiarowe.
-
FE-analysis of failure behaviour of reinforced concrete columns under eccentric compression
PublicationArtykuł omawia obliczanie słupów żelbetowych poddanych ściskaniu mimośrodowemu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu MES i sprężysto-plastycznego prawa konstytutywnego rozszerzonego o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Modelling of size effects in concrete using elasto-plascity with non-local softening
PublicationArtykuł przedstawia numeryczne symulacje MES efektów skali w materiałach kruchych takich jak beton , wykonane w warunkach płaskiego stanu odkształceń. Materiał był modelowany w ramach sprężysto-plastyczności z izotropowym wzmocnieniem i osłabieniem. W obszarze ściskania przyjęto liniowe kryterium Druckera-Pragera z niestowarzyszonym prawem płynięcia a w obszarze rozciągania liniowe kryterium Rankina ze stowarzyszonym prawem płynięcia....
-
DEM modelling of concrete fracture based on its structure micro-CT images
PublicationW rozdziale książki zawarto numeryczne wyniki mezoskopowe dotyczące postępującego pękania betonu na poziomie kruszywa. Do badania procesu pękania belki betonowej z karbem w trzech (3D) i dwóch (2D) wymiarach zastosowano metodę elementów dyskretnych (DEM). Niejednorodność betonu uwzględniono stosując czterofazowy opis: kruszywo, zaprawa, makropustki i międzyfazowe strefy przejściowe. W obliczeniach DEM na podstawie zdjęć rentgenowskich...
-
Discrete modeling of micro-structure evolution during concrete fracture using DEM
PublicationW artykule pokazano wyniki dyskretne DEM dla betonu poddanego ściskaniu i rozciąganiu jednoosiowemu. Wyniki siła-przemieszczenie i zarysowania porównano z doświadczeniami. Szczególną uwagę zwrócono na zjawiska mikrostrukturalne podczas zarysowania na poziomie kruszywa.
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublicationThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Evaluation of suitability for 3D printing of high performance concretes
Publication -
The Effect of Aggregate Shape on the Properties of Concretes with Silica Fume
Publication -
Porosimetric, Thermal and Strength Tests of Aerated and Nonaerated Concretes
Publication -
Modification of Lightweight Aggregate Concretes with Silica Nanoparticles—A Review
Publication -
Real-time proliferation of porcine cumulus cells is related to the protein levels and cellular distribution of Cdk4 and Cx43
Publication -
Nonsteroidal anti-inflammatory drugs modulate cellular glycosaminoglycan synthesis by affecting EGFR and PI3K signaling pathways
Publication -
The Impact of Intraspecies Variability on Growth Rate and Cellular Metabolic Activity of Bacteria Exposed to Rotating Magnetic Field
Publication -
Emerging Role of Adenylate Kinase 4 as a Metabolic Player Regulating Cellular Hypoxic Responses in Pulmonary Cells
Publication -
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublicationThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
Human Wharton’s Jelly—Cellular Specificity, Stemness Potency, Animal Models, and Current Application in Human Clinical Trials
Publication -
Analysis of expression of genes responsible for regulation of cellular proliferation and migration – microarray approach based on porcine oocyte model
Publication -
Morphological and cellular alternations of HepG2 cells overexpressing CYP3A4 after treatment with antitumor imidazoacridinone derivative C-1311
PublicationW pracy badano odpowiedź biologiczną komórek nowotworu wątroby HepG2 z nadekspresją izoenzymu CYP3A4 pod wpływem pochodnej imidazoakrydonu C-1311. Wyniki porównywano z odpowiedzią komórek HepG2 z tzw. wektorem zerowym.Izoeznym CYP3A4 jest jednym z izoenzymów cytochromu P450 odpowiedzialnych za przemiany metaboliczne pochodnej C-1311. Wykazano, że pochodna C-1311 indukuje w obu liniach komórkowych blok w fazie G2/M cyklu komórkowego,...
-
The cellular response of human hepatoma cells with different expression of CYP3A4 isoenzyme to treatment with triazoloacridinone derivative C-1305
PublicationCelem badań było określenie w jaki sposób ekspresja enzymów odpowiedzialnych za metabolizm pochodnej triazoloakrydonu C-1305 wpływa na odpowiedź komórek ludzkiego raka wątroby HepG2 i Hep3A4. W komórkach HepG2 triazoloakrydon C-1305 indukuje proces starzenia, podczas gdy w przypadku linii Hep3A4, komórki ulegają apoptozie oraz nekrozie.
-
Diclofenac Degradation—Enzymes, Genetic Background and Cellular Alterations Triggered in Diclofenac-Metabolizing Strain Pseudomonas moorei KB4
Publication -
The Effects of Cellular Membrane Damage on the Long-Term Storage and Adhesion of Probiotic Bacteria in Caco-2 Cell Line
Publication -
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublicationThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublicationThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublicationThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Effect of slag coal ash and foamed glass on the mechanical properties of two-stage concrete
PublicationTwo-stage concrete (TSC) is known by various names such as colcrete, Polcrete, preplaced aggregate concrete and prepacked concrete. It is different from traditional concrete in two fundamental ways, namely method of construction and mix proportion. Two-stage concrete (TSC) is defined as firstly, coarse aggregates are placed into the formwork and grout is applied to fill in the between coarse aggregate particles voids. Secondly,...
-
The role of tricalcium aluminate and gypsum dehydration level in cement for effective air entrainment of concrete
Publication -
Mechanical properties and interfacial transition zone microstructure of concrete with waste basalt powder addition
Publication -
Gypsum dehydration in cement and its impact on air-void structure in air-entrained concrete
Publication -
The Effect of Texturing of the Surface of Concrete Substrate on the Pull-Off Strength of Epoxy Resin Coating
Publication -
Behaviour of asphalt concrete in cyclic and static compression creep test with and without lateral confinement
PublicationArtykuł przedstawia wpływ metodyki badań na określanie parametrów betonu asfaltowego. Wykazano, że badania pełzania bez skrępowania bocznego w większym stopniu uwypuklają wpływ asfaltu na parametry badanego betonu asfaltowego natomiast w badaniach ze skrępowaniem bocznym, zarówno rola asfaltu jak i szkieletu mineralnego jest uwzględniana przy ocenie parametrów betonu asfaltowego. Ponadto wykazano, że lepszymi miarami do oceny betonu...
-
Automatic strength assessment of the virtually modelled concrete interfaces based on shadow-light images
Publication -
Effect of Nano-SiO2 on the Microstructure and Mechanical Properties of Concrete under High Temperature Conditions
Publication -
Insight into the microstructural and durability characteristics of 3D printed concrete: Cast versus printed specimens
PublicationThis study presents the comparison of microstructural and durability characteristics of 3D printed concrete (3DPC) depending on its production method (printing or casting). Printed samples with different numbers of layers, as well as a cast specimen with an identical mix composition, were produced and compared, with their microstructural pore and solid characteristics quantitatively and qualitatively investigated. For this purpose,...
-
Evaluation of effectiveness of hydrated lime additive in protecting asphalt concrete against water and frost
PublicationArtykuł przedstawia wyniki badań laboratoryjnych odporności betonu asfaltowego z dodatkiem wapna hydratyzowanego na działanie wody i mrozu. Niszczące oddziaływanie wody i mrozu oceniano przez zestawienie wytrzymałości na pośrednie rozciąganie i modułu sztywnosci sprężystej przed i po laboratoryjnej symulacji działania wody i mrozu zmodyfikowaną metodą Lottmana. Działanie 2 środków adhezyjnych (wapna hydratyzowanego i aminu tłuszczowego)...
-
Machine-learning methods for estimating compressive strength of high-performance alkali-activated concrete
PublicationHigh-performance alkali-activated concrete (HP-AAC) is acknowledged as a cementless and environmentally friendly material. It has recently received a substantial amount of interest not only due to the potential it has for being used instead of ordinary concrete but also owing to the concerns associated with climate change, sustainability, reduction of CO2 emissions, and energy consumption. The characteristics and amounts of the...
-
The effect of aggregate characteristics on the fracture behaviour of fine-grained concrete under tensile loading
PublicationArtykuł przedstawia analizę wpływu kruszywa na zjawisko pękania drobnoziarnistego betonu podczas quasi-statycznego trzypunktowego zginania. Beton został opisany jako stochastyczny i niejednorodny materiał trzyfazowy. Dwuwymiarowe obliczenia numeryczne dla betonowych belek z nacięciem wykonano metodą elementów skończonych stosując izotropowy materiałowy model z degradacją sztywności rozszerzony o długość charakterystyczną mikrostruktury...
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublicationEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublicationThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
Seismic probabilistic assessment of steel and reinforced concrete structures including earthquake-induced pounding
PublicationRecent earthquakes demonstrate that prioritizing the retrofitting of buildings should be of the utmost importance for enhancing the seismic resilience and structural integrity of urban structures. To have a realistic results of the pounding effects in modeling process of retrofitting buildings, the present research provides seismic Probability Factors (PFs), which can be used for estimating collision effects without engaging in...
-
Discrete element method modelling of elastic wave propagation in a meso-scale model of concrete
PublicationThis paper deals with the accurate modelling of ultrasonic wave propagation in concrete at the mesoscopic level. This was achieved through the development of a discrete element method (DEM) model capable of simulating elastic wave signals comparable to those measured experimentally. The main objective of the work was to propose a novel methodology for constructing a meso-scale model of concrete dedicated to the analysis of elastic...
-
Three dimensional simulations of FRC beams and panels with explicit definition of fibres-concrete interaction
PublicationHigh performance concrete (HPC) is a quite novel material which has been rapidly developed in the last few decades. It exhibits superior mechanical properties and durability comparing to normal concrete. HPC can achieve also superior tensile performance if strong fibres (steel or carbon) are implemented in the matrix. Thus, there exist the unabated interest in studying how the addition of different types of fibres modifies the...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Fracture simulations in concrete beam under bending using a mesoscopic model with cohesive elements
PublicationThe main aim of this paper was to investigate a complex fracture process in a concrete beam subjected to 3-point bending test by means of the 2D meso-scale FEM with 4-node cohesive elements embedded in the initial mesh of 3-node solid elements. The material heterogeneity was taken into account by considering 3 different phases (aggregate, cement matrix, ITZs) on the basis of randomly generated internal structure of concrete and...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublicationContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...