Filters
total: 3724
filtered: 2940
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: hydrophobic coating
-
Developing electrochemical measurements in order to assess anti-corrosive coatings more effectively
PublicationCelem pracy było sprawdzenie powtarzalności wyników uzyskanych metodą pomiaru szumu (Electrochemical Noise method - ENM) elektrochemicznego wykonanych na powłokach organicznych w konfiguracji bez połączenia z podłożem metalowym (NOCS - No Connection to the Substrate). NOCS polega na wykonaniu pomiarów na trzech teoretycznie takich samych obszarach badanego układu. W takim układzie nie jest wymagane połączenie elektryczne z metalowym...
-
Method using square-pulse excitation for high-impedance spectroscopy of anticorrosion coatings
PublicationArtykuł prezentuje metodę spektroskopii impedancyjnej przeznaczonej do diagnostyki powłok antykorozyjnych na obiektach bezpośrednio w terenie. Aby skrócić czas uzyskania widma impedancji (w zakresie od 1 mHz do 1 MHz) do kilku minut, wykorzystano sygnały harmoniczne do pomiaru widma powyżej 10 Hz a impuls prostokątny w dolnym zakresie częstotliwości. Do wyznaczania widma użyto algorytmów DSP odpowiednich do sygnału pobudzenia....
-
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio-Tribological Applications
PublicationZaprezentowano metodę badań ogólnej charakterystyki tribologicznej cienkich powłok ceramicznych z wykorzystaniem równoległych testów na wielu stanowiskach o różnej konfiguracji styku powierzchni trących i przy ruchu o różnym charakterze (jednokierunkowym i posuwisto zwrotnym). Przedstawiono wyniki porównania przy pomocy jednoczesnej analizy wyników testów z różnych stanowisk; w wyniku testów uzyskano ranking powłok ze wskazaniem...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete.
PublicationW pracy przedstawiono rezultaty badań elektrochemicznych polimerów przewodzących z pigmentem grafitowym. Wyznaczono parametry elektrochemiczne badanych powłok w trakcie długotrwałej polaryzacji zbrojonego betonu. W oparciu o pomiary impedancyjne wyznaczono parametry elektrochemiczne powłok przewodzących. Wykazano, że badane powłoki mogą być stosowane w ochronie katodowej żelbetu. Badania wykazały, że optymalne stężenie grafitu...
-
Cavitation erosion of chromium-manganese and chromium-cobalt coatings processed by laser beam
PublicationPrzedstawiono wyniki badań erozji kawitacyjnej napoin wykonanych za pomocą elektrod chromowo-manganowych i chromowo-niklowych oraz obrobionych wiązką lasera CO2 o mocy 1000 W. Próbki poddawano obciążeniom kawitacyjnym na stanowisku z wirującą tarczą. Zaobserwowano wzrost odporności kawitacyjnej napoin, w których dokonano przetopienia ich powierzchni promieniowaniem lasera.
-
Time domain diagnosis of anticorrosion coatings via shape designed measurement signals.
PublicationW pracy przedstawiono operującą w dziedzinie czasu metodę diagnostyki pokryć przeciwkorozyjnych, na poziomie identyfikacji parametrów obwodu zastępczego. Metoda jest oparta na pobudzeniu obiektu sygnałem niekonwencjonalnym o projektowanym kształcie i pomiarze odpowiedzi obiektu (tzw. obserwabla) po upływie zadanego czasu T. Parametry obwodu zastępczego są obliczane bezpośrednio z obserwabli na podstawie równań wynikających z topologii...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublicationMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublicationFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
Polyurethane/Silane-Functionalized ZrO2 Nanocomposite Powder Coatings: Thermal Degradation Kinetics
PublicationA polyurethane (PU)-based powder coating reinforced with vinyltrimethoxysilane (VTMS)-functionalized ZrO2 nanoparticles (V-ZrO2) for thermal stability was developed. Chemical structure, microstructure and thermal degradation kinetics of the prepared coatings were investigated. The peak of aliphatic C–H vibrating bond in the Fourier transform infrared (FTIR) spectrum of V-ZrO2 was a signature of VTMS attachment. Scanning electron...
-
Electrophoretic Deposition and Characteristics of Chitosan–Nanosilver Composite Coatings on a Nanotubular TiO2 Layer
PublicationThe surface treatment of titanium implants has been applied mainly to increase surface bioactivity and, more recently, to introduce antibacterial properties. To this end, composite coatings have been investigated, particularly those based on hydroxyapatite. The present research was aimed at the development of another coating type, chitosan–nanosilver, deposited on a Ti13Zr13Nb alloy. The research comprised characterization of the...
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublicationMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings
Publication: Titanium and its alloys is the main group of materials used in prosthetics and implantology. Despite their popularity and many advantages associated with their biocompatibility, these materials have a few significant disadvantages. These include low biologic activity—which reduces the growth of fibrous tissue and allows loosening of the prosthesis—the possibility of metallosis and related inflammation or other allergic reactions,...
-
Electrophoretic Deposition and Characterization of Chitosan/Eudragit E 100 Coatings on Titanium Substrate
PublicationCurrently, a significant problem is the production of coatings for titanium implants, which will be characterized by mechanical properties comparable to those of a human bone, high corrosion resistance, and low degradation rate in the body fluids. This paper aims to describe the properties of novel chitosan/Eudragit E 100 (chit/EE100) coatings deposited on titanium grade 2 substrate by the electrophoretic technique (EPD). The deposition...
-
Microstructure and mechanical properties of laser surface-treated Ti13nb13zr alloy with MWCNTs coatings
PublicationLaser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two...
-
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublicationTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
A distributed scheme for inter-domain routing optimization
Publication -
Analysis of resistive and inductive heating of railway turnouts
PublicationElektryczne ogrzewanie rozjazdów kolejowych jest istotnym problemem technicznym i ekonomicznym. Z tych względów potrzebne są badania w celu optymalizacji systemu ogrzewania rozjazdów kolejowych. W artykule przedstawiono analizę porównawczą strat energii podczas ogrzewania rozjazdów kolejowych z wykorzystaniem dwóch różnych metod. Analiza ogrzewania rozjazdów przeprowadzono w programie ANSYS.(Analiza oporowego i indukcyjnego nagrzewania...
-
Stability of a truss under upward wind loading
PublicationThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Multi-objective weather routing of sailing vessels
PublicationThe paper presents a multi-objective deterministic method of weather routing for sailing vessels. Depending on a particular purpose of sailboat weather routing, the presented method makes it possible to customize the criteria and constraints so as to fit a particular user’s needs. Apart from a typical shortest time criterion, safety and comfort can also be taken into account. Additionally, the method supports dynamic weather data:...
-
METHOD OF ROUTING SHIPS SAILING IN DEDICATED ENVIRONMENT
PublicationThe method for determining the suboptimal route of sailing vessels operating in a restricted area of the sea are proposed in the paper. The dynamics of the environment including weather conditions and speed characteristics of ships sailing are considered. As optimiza-tion criterion, measure sailing time T, and the number of maneuvers performed ω, are taken into account. An heuristic algorithm, and the appropriate application routing...
-
Counting Lattice Paths With Four Types of Steps
Publication -
Craving sensation in the assessment of alcohol-dependent persons
Publication -
Capon-like DoA estimator for rotating arrays
PublicationWe propose a nonparametric superresolution DoA estimator that is suitable for use with rotating arrays. The proposed method can be regarded as an extension of the Capon approach. We investigate its properties using computer simulations and present results obtained by processing of real world data.
-
Modeling of the internal combustion engine cooling system
PublicationThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
The evaluation of the surface quality after laser cutting
Publication -
Structural optimization of microjet array cooling system
PublicationThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Magnetoacoustic heating in a quasi-isentropic magnetic gas
PublicationThe nonlinear heating of a plasma which associates with the transfer of energy of magnetoacoustic waves into that of the entropy mode, is analytically studied. A plasma is uniform and motionless at equilibrium. Perturbations in a plasma are described by a system of ideal magnetohydrodynamic equations. The equilibrium straight magnetic strength and the wave vector form a constant angle which varies from 0 to π/2. There exist four...
-
Billiard in a rotating half-plane: modeling and dynamics
Publication -
Routing equal-size messages on a slotted ring
PublicationAnalizujemy problem routingu wiadomości w sieci slotted ring, biorąc pod uwagę dwa kryteria optymalizacyjne: długość uszeregowania oraz liczbę 'cykli' pracy sieci. Optymalny routing dla wiadomości o rozmiarze k jest silnie NP-trudny, natomiast dla k=q, gdzie q jest rozmiarem sieci, można obliczyć w czsie O(n^2log n) dla pierwszego kryterium. Podajemy również algorytm o czasie działania O(nlog n) oraz o stałym współczynniku dobroci....
-
Creating Acoustic Maps Employing Supercomputing Cluster
PublicationThe implemented online urban noise pollution monitoring system is presented with regard to its conceptual assumptions and technical realization. A concept of the noise source parameters dynamic assessment is introduced. The idea of noise modeling, based on noise emission characteristics and emission simulations, was developer and practically utilized in the system. Furthermore, the working system architecture and the data acquisition...
-
Methods of determining cutting forces during woodcutting
PublicationW artykule przedstawiono podstawowe metody określania sił przy przecinaniu drewna, które ulegały modyfikacjom wraz z postępem wynikającym z badań nad tym procesem. Przedstawione metody podzielono na dwie grupy: podejście klasyczne oraz nowatorskie podejście z zastosowaniem mechaniki pękania, które uwzględniają różne własności mające wpływ na proces przecinania. Podejście klasyczne reprezentują metody opierające się na właściwym...
-
Performance of a hybrid microjet – microchannel cooling module
PublicationThe paper presents the experimental investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary...
-
Development trends of automotive engine cooling systems
PublicationDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Creating a Realible Music Discovery and Recomendation System
PublicationThe aim of this paper is to show problems related to creating a reliable music dis-covery system. The SYNAT database that contains audio files is used for the purpose of experiments. The files are divided into 22 classes corresponding to music genres with different cardinality. Of utmost importance for a reliable music recommendation system are the assignment of audio files to their appropriate gen-res and optimum parameterization...
-
Cooling of electronic equipment by means of jets and microjets
PublicationW pracy przedstawiono rozwiązanie sprzężonej wymiany ciepła od uderzającej strugi cieczy oraz przewodzenia ciepła w łytce. Uzyskano proste zależności opisujące rozkład temperatur na płytce. Umożliwia to przeprowadzenie analizy wpływu różnych parametró na wymianę ciepła podczas chłodzenia urządzeń elektronicznych generujących ciepło.
-
Creating and application of maps of concepts for dl ontologies
PublicationW poprzednich pracach wprowadzono metodę reprezentacji wiedzy, zwaną Kartografią Wiedzy. Metoda ta pozwala na zapisanie, w formie tzw. map konceptów, zależności pomiędzy konceptami wyróżnionymi w terminologii, a następnie stopniowe (wraz ze wzrostem naszej wiedzy) przypisywanie indywidualnym obiektom tych konceptów. Efektywność budowy map konceptów jest kluczowym czynnikiem wpływającym na możliwość użycia metody. Niniejsza praca...
-
Simulation model for evaluation of QOS dynamic routing
PublicationCurrent informational networks use a large variety of technologies to support data exchange. Most of them are focused on IP protocol and include mechanisms which by definition should supply demanded QoS. One of those mechanisms is efficient path calculation - routing. Traffic offered to the network can change very rapidly in short term. Routing should support such traffic changes and all the time calculate valid paths in terms...
-
Acoustic heating in a weakly dispersive fluid flow
PublicationZbadano specyficzną rolę dyspersyjnych własności płynu w generacji ogrzewania przez straty energii fali akustycznej. Przedstawiono ilustracje zaistniałego ogrzewania powstającego na skutek przejścia dwoch typów fal - impulsowej i stacjonarnej.
-
Degradation of a nano-cutting tool: an MD simulation
PublicationW pracy przedstawiono wyniki symulacji wielokrotnego oddziaływania realistycznie ukształtowanego ostrza tnącego z modelowym, nieskończenie twardym ziarnem, przy zastosowaniu metody dynamiki molekularnej. Ostrze składało się z kilkuset tysięcy atomów metalu fcc, traktowanego za pomocą potencjału Suttona-Chena, przesuwane było ze stałą prędkością 20 m/s. Obserwowane deformacje plastyczne pojawiające się na skutek kontaktu ostrza...
-
Stochastic approach to the dynamics of a linear floating object
PublicationArtykuł stanowi prezentację metody różniczkowych równań stochastycznych w zastosowaniu do analizy dynamiki obiektów pływających. Analizowany jest ruch jednostki pływającej jako obiektu liniowego z uwzględnieniem w równaniach stochastycznych nieliniowości, występującej w wymuszeniach zewnętrznych działających na obiekt. Stochastyczne równania różniczkowe są zapisane dla sprzężonych ruchów symetrycznych.
-
Precision of cutting system in circular sawing machine
PublicationW pracy przedstawiono analizę dokładności układu przecinania pilarki tarczowej, w której uwzglednoino dokładność struktury geometryczno- ruchowej przecinarki.
-
New generation cooling systems for car engines
PublicationNormy czystości spalin silników samochodowych wymusiły rozwój elektronicznego sterowania pracą silników samochodowych. Do niedawna układy chłodzenia były bardzo tradycyjnymi - niesterowanymi programowo. W artykule przedstawiono możliwości wprowadzenia zaawansowanego sterowania mikroprocesorowego do układów chłodzenia silników spalinowych. Rozważania zilustrowano badaniami z literatury i własnymi pomiarami autora.
-
Utulization of biomass for heating purposes in pomeranian region
PublicationW publikacji przedstawiono analizę potencjału użycia odnawialnych źródeł energii do produkcji ciepła w regionie pomorskim. Każde miasto regionu zostało oszacowane pod względem potencjału użycia odnawialnych źródeł energii. Dwa obszary miejskie cechują się tym, że mają potencjał pokrycia swojego zapotrzebowania na ciepło tylko ze słomy, czyli możemy rozpatrywać produkcję ciepła z kotłów opalanych słomą jako 100% potencjalne zapotrzebowanie...
-
Stochastic approach to the dynamics of marine floating object
PublicationAnalizowany jest ruch jednostki pływającej z uwzględnieniem w równaniach stochastycznych nieliniowości, występującej w wymuszeniach zewnętrznych działających na obiekt. Stochastyczne równania różniczkowe są zapisane dla sprzężonych ruchów symetrycznych.
-
Some aspects surface cooling by impinging jet
PublicationW pracy przedstawiono wyniki badań wymiany ciepła, uskoku hydraulicznego i stabilności podczas napływu strugi na powierzchnię ciała stałego.
-
Measurement accuracy of the system to control the microwave heating.
PublicationPrzedstawiono skrótowo zasadę pracy i konstrukcję systemu do badań naukowych procesów grzania mikrofalowego. Wyprowadzono wyrażenie opisujące wartość średniokwadratową błędu pomiaru energii mikrofalowej i przeanalizowano składowe błędu pomiaru powodowane przez rzeczywiście występujące w układzie pomiarowym parametry techniczne jego części mikrofalowej.
-
Heating of fuse - elements in transient and steady - state
PublicationPrzedstawiono wyniki obliczeń numerycznych nagrzewania topików bezpieczników w stanach nieustalonych i ustalonych i wykonanych w pakiecie FLUX 2D. W obliczeniach uwzględniono nagrzewania całej wkładki bezpiecznikowej. Do analizy wybrano temperaturę w przewężeniu topika. W wyniku przeprowadzonych badań stwierdzono, że przy obliczaniu parametrów przedłukowych należy uwzględniać przewodzenie ciepła w topiku oraz brać pod uwagę zmienną...
-
Proposed concept for the development of residential floating facilities
PublicationCurrently, a dynamic growth of interest in residential buildings located on the water can be observed in Poland. However, the lack of legal regulations, the increase in society's affluence and overpopulation in city centers lead to reflection on the development strategy that should be implemented for maritime construction. The publication presents a proposal of four development strategy concepts: aggressive,...
-
Bearing testing machine with rotating load vector.
PublicationW pracy przedstawiono koncepcję konstrukcyjną i prototyp stanowiska badawczego z wirująca reakcją łożyskową przeznaczonego do testowania wytrzymałości zmęczeniowej warstw ślizgowych w łożyskach poprzecznych. Konstrukcja i przeznaczenie maszyny zbudowanej w laboratorium tribologicznym Politechniki Gdańskiej jest zgodna z zaleceniami normy ISO 7905. Przeanalizowano zalety i wady maszyny badawczej o takim wzorcu obciążenia testującego.
-
Limit Analysis of a Strip Footing on Stochastic Subsoil.
PublicationW pracy analizowana jest ława fundamentowa posadowiona na losowym podłożu.Poszukiwane są oszacowania nośności podłoża na podstawie twierdzeń o dolnej i górnej ocenie obciążenia granicznego. Dla różnych statycznie dopuszczalnych pól naprężenia i kinematycznie dopuszczalnych pól prędkości, wyznaczono wartości oczekiwane i wariancje obciążenia granicznego. Pozwoliło to na określenie odpowiednich dystrybuant, rozumianych...