Filters
total: 2686
filtered: 2379
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: grating
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Multicriteria Optimization Approach to Design and Operation of District Heating Supply System over its Life Cycle
PublicationDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). In the paper a method for optimized selection of design and operating parameters of long distance Heat Transportation System (HTS) is proposed. The method allows for evaluation of feasibility and effectivity of heat transportation...
-
Instantaneous Heating and Cooling Caused by Periodic or Aperiodic Sound of Any Characteristic Duration in a Gas with Vibrational Relaxation
PublicationThermodynamic relaxation of internal degrees of a molecule's freedom in a gas occurs with some characteristic time. This makes wave processes in a gas behave differently depending on the ratio of characteristic duration of perturbations and the relaxation time. In particular, generation of the secondary non-wave modes by intense sound in a nonlinear flow dependens on frequency. These kinds of interaction are considered in this...
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublicationThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
Release of Encapsulated Bioactive Compounds from Active Packaging/Coating Materials and Its Modeling: A Systematic Review
PublicationThe issue of achieving controlled or targeted release of bioactive compounds with specific functional properties is a complex task that requires addressing several factors, including the type of bioactive, the nature of the delivery system, and the environmental conditions during transportation and storage. This paper deals with extensive reporting for the identification of original articles using Scopus and Google Scholar based...
-
How do responsible universities perceive their social engagement? In search of signs of Creating Shared Value by the University
PublicationObjectives: University social responsibility still lacks legitimisation and is perceived as a burden that hinders academics from doing research and teaching. Creating Shared Value by the University may serve as a tool to motivate universities to engage in initiatives for society, as this is beneficial for both parties. Yet, some researchers perceive the creation of economic value as inappropriate for academia. Thus, it was interesting...
-
Study of Slip Effects in Reverse Roll Coating Process Using Non-Isothermal Couple Stress Fluid
PublicationThe non-isothermal couple stress fluid inside a reverse roll coating geometry is considered. The slip condition is considered at the surfaces of the rolls. To develop the flow equations, the mathematical modelling is performed using conservation of momentum, mass, and energy. The LAT (lubrication approximation theory) is employed to simplify the equations. The closed form solution for velocity, temperature, and pressure gradient...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four Different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-of adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by cyclic...
-
A new type of (TiZrNbTaHf)N/MoN nanocomposite coating: Microstructure and properties depending on energy of incident ions
PublicationA novel (TiZrNbTaHf)N/MoN nanocomposite coatings, which consist of the nitride of the high-entropy alloy and the binary nitride, were synthesized by vacuum-arc deposition at various substrate biases. The elemental composition, chemical bonding state, phase structure, microstructure and mechanical properties of the coatings were studied by high-resolution experimental methods: SIMS, GDMS, XPS, XRD, HR-TEM and nano-indentation. It...
-
Determination of grain shape of laser-irradiated FePdCu thin alloy films
Publication -
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Influence of analysis of features geometrical abrasive grains stress, strain and displacement of material in zone microgrinding
Publication -
On the Trail of the Oldest Domestic Cat in Poland. An Insight from Morphometry, Ancient DNA and Radiocarbon Dating
Publication -
Characterisation and OSL dating of modern fluvial sediments in the lower Vistula River: testing the zeroing assumption
Publication -
Silicon nanoparticles enhanced the growth and reduced the cadmium accumulation in grains of wheat (Triticum aestivum L.)
Publication -
Quality Improvement of Wear-Resistant Coatings in Plasma Spraying Integrated with High-Energy Heating by High Frequency Currents
Publication -
Formation of high-carbon abrasion-resistant surface layers when high-energy heating by high-frequency currents
Publication -
Effect of dietary inclusion of 1% or 3% of native chicory inulin on the large intestinal mucosa proteome of growing pigs
Publication -
THE DISTRIBUTION OF BIOACTIVE COMPOUNDS IN THE TUBERS OF ORGANICALLY GROWN JERUSALEM ARTICHOKE (HELIANTHUS TUBEROSUS L.) DURING THE GROWING PERIOD
Publication -
Thickness and structure change of titanium(IV) oxide thin films synthesized by the sol–gel spin coating method
Publication -
Adhesion of AlCrN coating deposited on TiB2/Ti composites sintered by SPS dedicated for high temperature tribological applications
Publication -
Water Needs of Black Locust Robinia pseudoacacia L. in the First Three Years of Growing in the Reclamation Plantings in Poland
Publication -
Study on Physicochemical Properties of Biocomposite Films with Spent Coffee Grounds as a Filler and Their Influence on Physiological State of Growing Plants
Publication -
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublicationThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Tracing financial innovation diffusion and substitution trajectories. Recent evidence on exchange-traded funds in Japan and South Korea.
PublicationSince the rapid growth of the popularity of ETFs, the potential substitution between innovative financial products, exchange-traded funds (ETFs), and traditional investment funds (open-end and closed-end funds) is recognized as one of the most-discussed issues in the financial industry. This is the first study to empirically verify and compare the diffusion and substitution of ETFs using monthly data on their assets in two selected...
-
"Creating a numerical model of noise conditions based on the analysis of traffic volume changes in cities with low and medium structure.
PublicationThe subject of this research study is to analyze noise conditions of the selected area in the city of Gdańsk using data related to traffic volume changes during a day. This is because daily distribution of noise levels is much more helpful for noise control and reduction than traditional maps with Lden levels indicated. Calculations are made with the use of a numerical model developed at the Gdansk Univ. of Technology and implemented...
-
"Creating a numerical model of noise conditions based on the analysis of traffic volume changes in cities with low and medium structure.
PublicationThe subject of this research study is to analyze noise conditions of the selected area in the city of Gdańsk using data related to traffic volume changes during a day. This is because daily distribution of noise levels is much more helpful for noise control and reduction than traditional maps with Lden levels indicated. Calculations are made with the use of a numerical model developed at the Gdansk Univ. of Technology and implemented...
-
A Canonical Switched Capacitor DC-DC Converter. A look at how the historical SC synthesis problem is getting solved
PublicationWe reconsider a solution to the historical problem in switched capacitor (SC) DC-DC converter synthesis. Specifically, we retackle the problem of constructing an SC twophase network realizing arbitrary voltage conversion ratio within rational bounds defined. Theoretical foundations are available in our earlier research [3] where a nonconstructive proof of existence was given. We briefly review and comment on known circuit solutions...
-
Praca z drewnem - Przestrzeń eksperymentu w tworzeniu architektury; Crafting Wood - Space of experiment in making architecture
PublicationW artykule przedstawiono eksperymenty z materiałem w tworzeniu architektury prowadzące do praktycznych rozwiązań w konstrukcji budynku. Takie podejście do tematyki zastosowania materiałów w architekturze nakreśla praktyczne aspekty tworzenia przestrzeni podczas pracy np. z drewnem. Podejście przedstawiono w kontekście dziedzictwa kulturowego podczas intensywnych warsztatów dotyczących tradycji i kultury budownictwa wybranych regionów...
-
Evaluation of polycaprolactone as a new sorbent coating for determination of polar organic compounds in water samples using membrane–SPME
PublicationCommercially available solid-phase microextraction fibers used for isolation of polar analytes are based on the adsorption phenomenon. In consequence, typical limitations bonded with analytes displacement and matrix effects are very frequent. In the present study, alternative solution is described. Polycaprolactone (PCL) was used for the first time as sorbent to isolate polar organic compounds from water samples using the membrane–solid-phase...
-
Thickness and structure change of titanium (IV) oxide thin films synthesized by the sol–gel spin coating method
PublicationTitanium dioxide is a well-known material in nanotechnology, while it provides new opportunities due to its interesting properties, for example, as a semiconductor with a quite significant forbidden band gap energy of 3.2 eV. In this study, thin films of titanium dioxide (TiO2) were synthesized in amorphous and crystallographic systems using the sol–gel process. Atomic Force Microscopy (AFM), Raman spectroscopy and X-ray diffraction...
-
Light pollution from illuminated bridges as a potential barrier for migrating fish–Linking measurements with a proposal for a conceptual model
PublicationIlluminated bridges have become important assets to navigable aquatic systems. However, if artificial light at night (ALAN) from illuminated bridges reaches aquatic habitats, such as rivers, it can threaten the river's natural heterogeneity and alter the behavioural responses of migratory fish. Here, via a pilot study, we quantified levels of ALAN at illuminated bridges that cross a river and, propose a conceptual model to estimate...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublicationThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
Dynamic GPU power capping with online performance tracing for energy efficient GPU computing using DEPO tool
PublicationGPU accelerators have become essential to the recent advance in computational power of high- performance computing (HPC) systems. Current HPC systems’ reaching an approximately 20–30 mega-watt power demand has resulted in increasing CO2 emissions, energy costs and necessitate increasingly complex cooling systems. This is a very real challenge. To address this, new mechanisms of software power control could be employed. In this...
-
Polymeric metal‐containing ionic liquid sorbent coating for the determination of amines using headspace solid‐phase microextraction
PublicationThis study describes the design, synthesis, and application of polymeric ionic liquid sorbent coatings featuring nickel metal centers for the determination of volatile and semivolatile amines from water samples using headspace solidphase microextraction. The examined polymeric ionic liquid sorbent coatings were composed of two ionic liquid monomers (tetra(3-vinylimidazolium)nickel bis[(trifluoromethyl)sulfonyl]imide [Ni2+(VIM)4]...
-
Mechanical Properties and Wear Susceptibility Determined by Nanoindentation Technique of Ti13Nb13Zr Titanium Alloy after “Direct Laser Writing”
PublicationLaser treatment has often been applied to rebuild the surface layer of titanium and its alloys destined for long-term implants. Such treatment has always been associated with forming melted and re-solidified thin surface layers. The process parameters of such laser treatment can be different, including the patterning of a surface by so-called direct writing. In this research, pulse laser treatment was performed on the Ti13Nb13Zr...
-
Effect of Sieve Unit Inclination Angle in a Rotary Cleaning Device for Barley Grain
Publication -
Effect of Grain Husk Microfibers on Physicochemical Properties of Carboxymethyl Polysaccharides-Based Composite
Publication -
Enhanced aging resistance of poly(ε-caprolactone)/brewers’ spent grain composites
PublicationThe presented paper investigated the influence of brewers’ spent grain (BSG) extrusion pa-rameters on the photo-oxidative resistance of poly(ε-caprolactone)-based wood polymer composites. Filler samples characterized by the higher melanoidin content were more efficient in hindering of poly-mer degradation, inhibiting the decomposition of the polymer amorphous phase. As aresult, deteriora-tion of mechanical performance was limited,...
-
Changes in Eating Behaviour during SARS-CoV-2 Pandemic among the Inhabitants of Five European Countries
Publication -
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublicationLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Inulin-type fructans trigger changes in iron concentration and activity of bone metabolism biomarkers in blood plasma of growing pigs
Publication -
Identification of predicted genes expressed differentially in pituitary gland tissue of young growing bulls revealed by cDNA-AFLP technique
Publication -
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublicationW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Active Annotation in Evaluating the Credibility of Web-Based Medical Information: Guidelines for Creating Training Data Sets for Machine Learning
PublicationMethods Results Discussion References Abbreviations Copyright Abstract Background: The spread of false medical information on the web is rapidly accelerating. Establishing the credibility of web-based medical information has become a pressing necessity. Machine learning offers a solution that, when properly deployed, can be an effective tool in fighting medical misinformation on the web. Objective: The aim of this study is to...
-
Modelling Long‐Term Transition from Coal‐Reliant to Low‐Emission Power Grid and District Heating Systems in Poland
PublicationEnergy systems require technological changes towards climate neutrality. In Poland, where the power system is dominated by outdated coal-fired power plants, efforts to minimize the environmental impact are associated with high costs. Therefore, optimal paths for the development of the energy sector should be sought in order to achieve ambitious long-term strategic goals, while minimizing the negative impact on the consumers’ home...
-
Creating private and public value in data-related management projects: a cross-border case study from Switzerland and Italy
PublicationThe literature in the field of smart cities shows a continuous emphasis and interest in the topic of big data due to the extensive use of Information and Communication Technologies by public and private institutions within each city. There is undoubtedly value in big data: in data lie insights on the city, its stakeholders, citizens, products, and services. Challenges, though, lie in data’s variety, volume, and velocity, but also...
-
Bioactive and biodegradable cotton fabrics produced via synergic effect of plant extracts and essential oils in chitosan coating system
PublicationFunctional antibacterial textile materials are in great demand in the medical sector. In this paper, we propose a facile, eco-friendly approach to the design of antibacterial biodegradable cotton fabrics. Cotton fiber fabrics were enhanced with a chitosan coating loaded with plant extracts and essential oils. We employed Fourier-transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS), UV–Vis spectrophotometry, optical...
-
Friction and flow around growing tissue in bioreactor. Proceedings of the Biomechanics 2003. Engineering Biomechanics - Biomechanics of Sport - Medical Biomechanics.
PublicationPrzedstawione zostały problemy teoretyczne związane z wyznaczaniem sił tarcia, współczynników tarcia, rozkładów wartości ciśnienia w warstwie przyściennej wytworzonej wokół hodowanej tkanki w bioreaktorze w trakcie opływu tej tkanki cieczami biologicznymi o właściwościach lepkosprężystych. Model Rivlina Ericksena lepkosprężystej cieczy biologicznej jest tu brany pod uwagę.
-
Ekonomična efektivnist` teplovoï pompi v sistemi opalennâ = Economical efficiency of heat pump system in heating system
PublicationW artykule opisano wynik porównawczych obliczeń kosztów ogrzewania budynku jednorodzinnego. Porównano koszty konwencjonalnego ogrzewania z kotłem olejowym jako źródłem ciepła z kosztami ogrzewania układem hybrydowym, w którym współpracują ze sobą dwa żródła ciepła: konwencjonalny kocioł olejowy i sprężarkowa pompa ciepła. Wykonano studium parametryczne kosztów ogrzewania z wykorzystaniem metody kosztów narastających.