Search
Filters
total: 343
filtered: 250
Search results for: ELECTRODYNAMIC ACTUATOR
-
Suitability study of hybrid model of electrodynamic actuator
PublicationThis paper presents the proposal of the hybrid circuit-field model of an electrodynamic actuator. The field model uses the inductor current as the input data which is obtained from the circuit model or experimentally. The field model implemented using the FLUX program makes it possible to easily determine the pressure distribution acting on the disc. The results have been verified experimentally.
-
Suitability study of hybrid model of electrodynamic actuator
PublicationThe paper presents the proposal of the hybrid circumferential model of an electrodynamic actuator. The field model uses the inductor current as the input data which is obtained from the circumferential model or experimentally.
-
Study of the effect of adiabatic heating on the operation of the electrodynamic actuator
PublicationElectrodynamic actuators are used in hybrid switching systems where a very quick contact separation as well as operation repeatability and long-term reliability are required. The article presents selected results of thermal studies in the electrodynamic drive system. Study was carried out on the basis of the 3D electromagneto-thermal model implemented in the Ansys_Maxwell environment. The present model allows to determine the critical...
-
Modeling of Electrodynamic Phenomena in an Ultra-Rapid Inductive–Dynamic Actuator as Applied to Hybrid Short-Circuit Breakers - A Review Study
PublicationThis article is a study of the research development of electrodynamic phenomena occurring in ultra-fast electrodynamic drives. These types of linear drives are among the fastest, not only because of the huge accelerations achieved, but, above all, because of the extremely short reaction time. For this reason, electrodynamic drives are used in hybrid short-circuit breakers. The phenomena occurring in this type of drive are actually...
-
Shape and force control of cable structures with minimal actuators and actuation
Publication -
Shape and force control of cable structures with minimal actuators and actuation
PublicationShape adjustment and stress control can be considered as one of the effective parameters in prestressed cable structures since such structures are widely constructed nowadays due to their characteristics. The assembly errors and applied loads hugely affect the cables’ nodal positions and stress due to their delicacy. The former could disturb the shape, which affects the appearance and the function of the structure. In contrast,...
-
Static Shape and Stress Control of Trusses with Optimum Time, Actuators and Actuation
PublicationTraditional shape and stress control of structures use many actuators and require enormous time to find reasonable solutions that need designers to input specific target displacement and stress. This study employs a linear technique to static shape and stress control of pin-jointed assemblies as a theoretical advancement to prior works and provides a comparative analysis against previously established works. The study evaluates...
-
Redundant Actuation of 3RRR over-actuated Planar Parallel Manipulator
PublicationPraca opisuje zagadnienia modelowania i napędzania manipulatorów równoległych. Cechą charakterystyczną manipulatorów równoległych jest występowanie jednego lub kilku łańcuchów kinematycznych zamkniętych (gałęzi równoległych). Standardowo, konstrukcje takie są napędzane jedynie silnikami montowanymi w parach kinematycznych łączących łańcuchy kinematyczne z podstawą. Niekiedy konstrukcje takie są układami napędzanymi nadmiarowo (liczba...
-
Advances in computational electrodynamics.
PublicationArtykuł prezentuje wybrane metody, które są rozwijane w Politechnice Gdańskiej, i które mogą być wykorzystane do przyspieszenia komputerowego projektowania układów mikrofalowych i analizy numerycznej układów niskiej i dużej częstotliwości. Przeprowadzono przegląd metod tworzenia układów zastępczych i ich wykorzystanie do automatycznego projektowania filtrów pasmowo-przepustowych. Przedstawiono różne podejścia reprezentacji pola...
-
The Dynamical Projectors Method Hydro and Electrodynamics
PublicationThe dynamical projectors method proves to reduce a multicomponent problem to the simplest one-component problem with its solution determined by specific initial or boundary conditions. Its universality and application in many different physical problems make it particularly useful in hydrodynamics, electrodynamics, plasma physics, and boundary layer problems. A great variety of underlying mechanisms are included making this book...
-
A strategy of minimal torque modifications in a question of actuation strategy for an over-actuated system of a planar walking robot
PublicationPraca opisuje zagadnienia modelowania i napędzania robotów kroczących. Na pewnych etapach ruchu, konstrukcje takie są układami napędzanymi nadmiarowo (liczba napędów/silników jest większa niż liczba stopni swobody układu). Dzieje się tak z uwagi na więzy jednostronne występujące w układzie. Dla układów płaskich, po pojawieniu się kontaktu koła i odnóża, układ o sześciu stopniach swobody przechodzi w układ o trzech stopniach swobody....
-
Electrodynamic interaction in bus bar arrangements during short-circuits.
PublicationW artykule przedstawiono skutki oddziaływania sił elektrodynamicznych w układzie szyn zbiorczych rozdzielnic podczas zwarć metalicznych i łukowych. Przedstawiono metodę obliczania ugięć i naprężeń w szynach od sił elektrodynamicznych. Opisano wpływ łuku zwarciowego na zwiększenie sił elektrodynamicznych działających na szynę skrajną. Omówiono wpływ rezystancji niskonapięciowego łuku zwarciowego na ograniczenie pradów zwarciowych....
-
Interference in axisymmetric synthetic jet actuator
Publication -
Synthetic jet actuator with two opposite diaphragms
Publication -
Formulation of Time-Fractional Electrodynamics Based on Riemann-Silberstein Vector
PublicationIn this paper, the formulation of time-fractional (TF) electrodynamics is derived based on the Riemann-Silberstein (RS) vector. With the use of this vector and fractional-order derivatives, one can write TF Maxwell’s equations in a compact form, which allows for modelling of energy dissipation and dynamics of electromagnetic systems with memory. Therefore, we formulate TF Maxwell’s equations using the RS vector and analyse their...
-
Optimised allocation of actuators for DWDS
PublicationThis paper addresses the problem of actuators’ allocation within networked structured system, namely allocation of disinfectant booster stations within Drinking Water Distribution System (DWDS), under receding horizon optimised control – Model Predictive Control (MPC) to be exact. The allocation task is kept within dynamic multiobjective optimisation framework. The MPC is defined as a single objective predictive operator. Two numerical...
-
Comparative Analysis of Exoskeletal Actuators
PublicationSince the beginning of the development of exoskeletons in the early 1960s there was a constant need for improving their actuators technology. Requirements for high power and torque for the lower body and very high precision for the hand motion, while maintaining the flexibility of biological muscles, are still not fully satisfied. The problem lies not just in the lack of appropriate actuator technology, but also in the inability...
-
Acoustic and Flow Aspects of Novel Synthetic Jet Actuator
Publication -
Wave propagation in a sensor/actuator diffusion bond model
Publication -
On forced vibrations of piezo-flexomagnetic nano-actuator beams
PublicationThe effect of excitation frequency on the piezomagnetic Euler-Bernoulli nanobeam taking the flexomagnetic material phenomenon into consideration is investigated in this chapter. The magnetization with strain gradients creates flexomagneticity. We couple simultaneously the piezomagnetic and flexomagnetic properties in an inverse magnetization. Resemble the flexoelectricity, the flexomagneticity is also size-dependent. So, it has...
-
Multi-DBD actuator with floating interelectrode for aerodynamic control
PublicationIn this paper the use of a floating inter-electrode in a multi-DBD (dielectric barrier discharge) plasma actuator is described. The multi-DBD plasma actuators with floating inter-electrodes were investigated to get a longer DBD on a dielectric surface and to maximise generated net airflow. Our actuator was used to control the boundary layer flow separation around NACA0012 airfoil model. The results of our investigations suggests...
-
Effect of power frequency on the stress state of disc actuator
PublicationThis paper presents the concept of determining the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics. The disc stress is determined on the basis of solution of vibrating thin plate equation. Magnetic pressure acting on the disc is obtained from a hybrid circumferentially-field...
-
Effect of power frequency on the stress state of disc actuator
PublicationThe paper presents the concept of determinig the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics.
-
Modelling and simulations in time-fractional electrodynamics based on control engineering methods
PublicationIn this paper, control engineering methods are presented with regard to modelling and simulations of signal propagation in time-fractional (TF) electrodynamics. That is, signal propagation is simulated in electromagnetic media described by Maxwell’s equations with fractional-order constitutive relations in the time domain. We demonstrate that such equations in TF electrodynamics can be considered as a continuous-time system of...
-
Synthetic jet actuator efficiency based on the reaction force measurement
Publication -
Impact of the Soundproofing in the Cavity of the Synthetic Jet Actuator on the Generated Noise
Publication -
Research on Linear Actuators for Active Foil Bearings
PublicationActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublicationThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
Thermal and Electrodynamic Risk of Residual Current Devices in the Case of Back-Up Protection by Overcurrent Circuit Breakers
PublicationResidual current operated circuit breakers without integral overcurrent protection should be back-up protected. As back-up protection devices, overcurrent circuit breakers are used. The maximum let-through energy and let-through current of the overcurrent devices were evaluated under laboratory conditions. The thermal and electrodynamic risk of residual current devices was analyzed.
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublicationHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublicationThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...
-
Intelligent Material Actuators and Their Applications for Structural Dynamic Control
PublicationThe paper presents an application of inteligent materials to vibration control of structures.
-
Adaptive dynamic control allocation for over-actuated dynamic positioning system based on backstepping method in case of thruster faults
PublicationThe objective of the research considered in this paper is dynamic positioning of a nonlinear over-actuated marine vessel in the presence of limited information about thruster forces. First, the adaptive backstepping method is used to estimate the input matrix which will compensate partial loss of actuator effectiveness in the presence of actuator dynamics. Then, the adaptive commanded virtual forces and moment are allocated into...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublicationEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
Acoustic and Flow Aspects of Synthetic Jet Actuators with Chevron Orifices
Publication -
Design and modeling of the piezoelectric motor based on three resonance actuators
PublicationThis paper describes a piezoelectric motor which combines advantages from two existing piezoelectric motors topologies. The research work presents the design, simulations and measurements of the piezoelectric motor with three rotation-mode actuators. The aim of the project was to obtain the high speed piezoelectric motor. Other advantages of this conception are blocking torque, short response times, the ability to work in a hostile...
-
On the problem of optimised allocation of water quality sensors and actuators in DWDS
PublicationThe problems of water quality sensors and actuators placement in drinking water distribution systems (DWDSs) are addressed as separate, primarily. However, against the background of control systems theory, the nature of DWDSs dynamics indicates that these both problems are interdependent and impact the design of related water quality monitoring and control structures and algorithms. The research work presented in this paper is...
-
Object oriented grid computing for computational electromagnetics
PublicationArtykuł opisuje bibliotekę WiCommGrid napisaną w języku java, która realizuje ideę wymiany informacji pomiędzy węzłami środowiska rozproszonego z zastosowaniem programowania zorientowanego obiektowo. Biblioteka ta przystosowana jest do współdziałania z wieloma systemami operacyjnymi oraz z rożnym środowiskiem sprzętowym. Zbudowaną aplikację zastosowano do zrównoleglonych obliczeń rozkładu pola elektromagnetycznego w oparciu o algorytm...
-
Thermal, flow and acoustic characteristics of the heat sink integrated inside the synthetic jet actuator cavity
Publication -
Design and simulation of a new prototype of piezoelectric cantilever sensor/actuator for analysis of the soft tissues properties
PublicationThis paper is devoted to a new prototype of piezoelectric cantilever transducer dedicated for the characterization of the mechanical properties of soft tissues. General description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing one. Constitutive equations are presented for the active and passive layer of...
-
Buckling and shape control of prestressable trusses using optimum number of actuators
PublicationThis paper describes a method to control the nodal displacement of prestressable truss structures within the desired domains. At the same time, the stress in all members is unleashed to take any value between the allowable tensile stress and critical buckling stress. The shape and stresses are controlled by actuating the most active members. The technique considers the members’ initial crookedness, residual stresses, and slenderness...
-
Analytical Modelling of the Multicell Piezoelectric Motor Based on Three Resonance Actuators
PublicationThis paper presents analytical model of the multicell piezoelectric motor. The results, obtained in the field of piezoelectric motors, have pointed out that these motors have potentially high possibilities in the future of special applications. The studied multicell piezoelectric motor have a stator using three rotating mode actuators. A theoretical analysis of operating principle of the rotating mode motor has been described....
-
Electrostatic Zipping Actuators—Analysis of the Pull-In Effect Depending on the Geometry Parameters
PublicationContinuous work on a new generation of actuators, referred to as artificial muscles, resulted in the initiation of work on electrostatic zipping actuators, the concept of which is derived from micro electro-mechanical devices. Despite partial knowledge of their basic operating parameters, a question remains whether electrostatic zipping actuators are able to meet the expectations in the context of generated forces and control possibilities....
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Enhancement of lift and drag performances of a NACA0012 airfoil by multi-DBD plasma actuator with additional floating interelectrodes
PublicationIt is clear that the improvement of aircraft aerodynamic performances is currently and will continue to be a significant area of research for the aeronautical industry. The current study is focused on theenhancement of aerodynamic airfoil performances by using a multi-DBD plasma actuator mounted around the model leading-edge. Experiments have been conducted at the University of Orleans, in the 2 m x 2 m test section of a large...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Multi-DBD plasma actuator for flow separation control around NACA 0012 and NACA 0015 airfoil models
PublicationIn this paper application of innovative multi-DBD plasma actuator for flow separation control is presented. The influence of the airflowgenerated by this actuator on the flow around NACA 0012 and NACA 0015 airfoil models was investigated. The results obtained from 2D PIVmeasurements showed that the multi-DBD actuator with floating interelectrode can be attractive for leading and trailing edge separation control.
-
Underwater robot actuated by shape memory alloy wires
PublicationW pracy przedstawiono koncepcję projektu robota podwodnego z napędem wykorzystującym materiały SMA ze stopów z pamięcią kształtu. Rozpatrywany układ ma budowę modułową złożoną z segmentów na podobieństwo do anatomicznej budowy dżdżownicy. Pojedyńczy segment składa się z dwóch okrągłych tarcz, pomiędzy którymi umieszczono balon wypełniony wodą. Wielkość balonu jest dopasowana w taki sposób do rozmiarów tarcz oraz długości sprężyn...
-
Trajectory tracing problem for a redundantly actuated walking robot
PublicationPraca prezentuje zagadnienia modelowania dynamiki robotów kroczących. Rozważany robot jest układem o zmiennej liczbie stopni swobody. Wynika to z obecności więzów jednostronnych występujące w układzie. Jak dla większości układów o zmiennej liczbie stopni swobody, w niektórych z konfiguracji roboczych liczba silników przekracza liczbę stopni swobody. (dla układów płaskich, po pojawieniu się kontaktu koła i odnóża, układ o sześciu...
-
Synthetic Jet Actuators with the Same Cross-Sectional Area Orifices-Flow and Acoustic Aspects
Publication