Filters
total: 1498
-
Catalog
displaying 1000 best results Help
Search results for: polimery organometaliczne
-
Toughness augmentation by fibrillation and yielding in nanostructured blends with recycled polyurethane as a modifier
PublicationIn the present paper, we have carefully investigated the morphology and fracture mechanism of the recycled polyurethane (RPU) /epoxy blend system. The second phase (RPU) added to the epoxy resin has a positive effect on the overall mechanical properties. Interestingly, the recycled polymer has a remarkable effect on the fracture toughness of epoxy resin. The mechanism behind the fracture toughness improvement up on the addition...
-
THE ANALYSIS OF THE INFLUENCE OF STRESS DISTRIBUTION ON WEAR PROFILE IN LUBRICATED SLIDING CONTACT OF UHMW-PE VS TITANIUM Ti-13Nb-13Zr ALLOY
PublicationMetal – polymer sliding contacts are a typical combination in industry and medicine. For decades such a set of materials has been the primary choice in human joints endoprosthetic technology. In this paper tribological issues of are presented from a research on the potential for practical use of Ti-13Nb-13Zr/UHMW-PE couple for orthopedic endoprosthesis. In tests on simplified models it is critically important to carefully...
-
Fabrication and properties of electrode material composed of ordered titania nanotubes and pEDOT:PSS
PublicationWe report on the two-stage preparation method of electrode material composed of titania nanotubes and poly(3,4-ethylenedioxythiopene):poly(2-styrenesulphonate) conductive polymer (pEDOT:PSS). Initially, titania nanotube arrays were produced by the anodization process of Ti substrate. Next, the polymer was potentiostatically deposited onto the thermally annealed nanotube arrays from the electrolyte containing monomer and counter...
-
Environmental impact and industrial development of biorenewable resources for polyurethanes
PublicationPolyurethanes are among the most developed types of polymers. They are produced from the three primary components, i.e., polyols, low-molecular-weight glycols used as chain extenders, and diisocyanates. Until recently, all these substrates have been obtained via petrochemical processes. A decrease in petroleum-based resources and new ecological trends in chemistry, chemical technology, and materials engineering have generated increasing...
-
Badania właściwości elastomeru polimerowego jako materiału do redukcji drgań budowli poddanych obciążeniom sejsmicznym i parasejsmicznym
PublicationCelem niniejszej pracy jest przedstawienie wyników badań eksperymentalnych, przeprowadzonych na próbkach wykonanych z elastomeru polimerowego, wykorzystywanego w metodzie złączy podatnych. W referacie zaprezentowano wyniki badań statycznych dla ściskania oraz rozciągania, a także rezultaty z dynamiczno-mechanicznej analizy termicznej (DMA), której celem było przedstawienie zmian modułu zachowawczego, modułu stratności oraz tangensa...
-
Functionalized polyolefins, synthesis application and industrial relevance
PublicationPolymers play a key role in our modern life full of technical advances and a continuous request for new materials with tailored properties for a low price. Their excellent mechanical properties, good processability, chemical stability and low price make polyolefins the polymers of choice for most commodity and some more specialized applications. As a result, polyolefins account for over 65% of the total world demand of plastic...
-
2022 Ecological aspects of polymer package recycling
e-Learning Courses -
2023 Ecological aspects of polymer package recycling
e-Learning Courses -
Wstęp do Technologii Polimerów - LABORATORIUM - 2021/2022
e-Learning CoursesKierunek: Technologia Chemiczna Studia I Stopnia - Semestr IV
-
Problemy pomiarów niewielkich wartości ładunku występujących w procesie drzewienia elektrycznego. VI Ogólnopolskie Sympozjum Inżynieria Wysokich Napięć - IW 2002.
PublicationReferat zawiera omówienie problemów rejestracji niewielkich wartości impulsów prądowych o ultrakrótkich czasach trwania. Przedstawiono tu metodę pomiaru impulsów prądowych związanych z ładunkiem wstrzykiwanym do polimeru z elektrody ostrzowej przy napięciu przemiennym. W pracy zawarto także wyniki wstępnej serii badań mającej na celu przetestowanie zmodyfikowanego układu probierczego.
-
Wpływ przepięć na degradację izolacji polietylenowej. VI Ogólnopolskie Sympozjum Inżynieria Wysokich Napięć - IW 2002.
PublicationOmówiono wyniki badań wskazujące na istotny w procesie degradacji izolacji polietylenowej wpływ przepięć nakładanych na napięcie przemienne. Przeprowadzone badanie termicznie stymulowanej depolaryzacji cienkich próbek folii polietylenowej narażonych napięciem przemiennym oraz skojarzonym pozwoliły określić rodzaj napięcia efektywnie wprowadzającego ładunek do polimeru, wartość ładunku i jego energię aktywacji.
-
Badania osadu czynnego jako sorbentu oleju.
PublicationPrzeprowadzono badania właściwości sorpcyjnych wysuszonego osadu czynnego względem ciekłych węglowodorów. Zastosowano dwie techniki eksperymentalne:metodę wzniesienia kapilarnego i dynamiczną sorpcję oleju z dyspersji typu olej w wodzie. Sorbent uzyskany z osadu flokulowanego za pomocą polimeru organicznego był lepiej zwilżany niż sorbent otrzymany z osadu zagęszczanego bez dodatków chemicznych.
-
Degradation of polycaprolactone modified with TPS or CaCO3 in biotic/abiotic seawater
PublicationThis paper is an investigation of the polymer degradation process in two types of seawater (with and without microorganisms) sourced from the Baltic Sea. The chosen polymeric materials were polycaprolactone modified with either thermoplastic starch (PCL/TPS>85%) or calcium carbonate (60% PCL/40% CaCO3) compared directly against unmodified polycaprolactone. All samples were incubated for 28 weeks in seawater with and without microorganisms...
-
Simultaneous determination of Na+, K+, Ca2+, Mg2+ and Cl- in unstimulated and stimulated human saliva using all solid state multisensor platform
PublicationHuman saliva is one of the body fluids which collection method is relatively simple and non-invasive. The article is dedicated to assess concentration (activity) of Na+, K+, Ca2+, Mg2+ and Cl- in fresh, unstimulated or stimulated human saliva samples using single solid contact ion-selective electrodes with conventional reference electrode and self-made multisensor platform (MP) equipped with ion-selective membranes for Na+, K+,...
-
Measurements of guided wave propagation in CFRP/steel adhesive joints obtained by scanning laser vibrometry
Open Research DataThe DataSet contains guided wave signals measured in adhesive joints of steel plates (steel of type S355 with a thickness of 11.9 mm ) and carbon fibre reinforced polymer (CarboDur S1012 with a thickness of 1.24 mm). The samples were as follows: #0 – intact; #1 – 10% disbond; #2 – 20% disbond; #3 – 50% disbond; #4 – 80% disbond; #5 – 100% disbond.
-
Przebieg i produkty procesu pirolizy wybranych tworzyw sztucznych w reaktorze cisnieniowym
PublicationW badaniach przeprowadzono pirolizę, która miała na celu otrzymanie palnego gazu oraz oleju, wykorzystywanych jako paliwa energetyczne, z odpadowych materiałów pochodzenia polimerowego. Tworzywa sztuczne wytwarzane w największej ilości na świecie to polietylen (PE), polipropylen (PP), politereftalan etylenu (PET), Poli(chlorek winylu) (PVC). Mając to na uwadze do doświadczeń wybrano trzy polimery - PET, PE, PP, które poddawano...
-
Molecular dynamics simulations of the growth of poly (chloro-para-xylylene) films.
PublicationParylene C, poly(chloro-para-xylylene) is the most widely used member of the parylene family due to its excellent chemical and physical properties. In this work we analyzed the formation of the parylene C film using molecular mechanics and molecular dynamics methods. A five unit chain is necessary to create a stable hydrophobic cluster and to adhere to a covered surface. Two scenarios were deemed to take place. The obtained results...
-
Catena-Poly[[(tetrahydrofuran-κO)lithium(I)]-μ-1,1,3,3-tetraphenyl-triphosphane-κ^2P1^,P3^:κP2^]
PublicationTytułowy związek [Li(C24H20P3)(C4H8O)]n, został otrzymany w reakcji chlorku bis(trifenylofosfan)platyny(II) z 1,1-difenylo-2-(trimetylosililo)-2-litiadifosfanem, (C6H5)2P-P(SiMe3)Li*3C4H8O. Związek ten powstaje w późniejszym stadium reakcji. Jest to pierwszy polimer koordynacyjny wśród znanych soli litowych trifosfanów.
-
Properties of a polyethyleneimine-based sensor for measuring medium and high relative humidity
PublicationW artykule przedstawiono metodę przygotowania filmów polimerowych o zwiększonej odporności na działanie wody. Polietylenoimina została usieciowana w podwyższonej temperaturze. Określono optymalną kompozycję polimeru oraz temperaturę sieciowania. Czujniki rezystancyjne przygotowano metodą ''dip-coating''. Otrzymane czujniki charakteryzują się doskonałą trwałością w wysokich wilgotnościach. Elektryczne parametry czujników określono...
-
Badania spektroskopowe wybranych silanotiolanów metali o budowie polimerycznej
PublicationPodjęto próby otrzymania tri-tert-butoksysilanotiolanowych kompleksów niklu(II), kobaltu(II), cynku(II) i kadmu(II) o budowie polimerycznej mogących pełnić rolę prekursorów w syntezie materiałów funkcjonalnych. W tym celu przeprowadzono syntezy odpowiednich silanotiolanowych metali z grupą diamin alifatycznych. Otrzymano szereg nowych obojętnych polimerów koordynacyjnych o budowie przestrzennej typu 1D. Dla siedmiu z nich zostały...
-
Impedance spectroscopy studies on hybrid materials consisting of poly(3,4-ethylenedioxythiophene) and iron, cobalt and nickel hexacyanoferrate
PublicationBadania warstw polimeru pEDOT modyfikowanego heksacyjanożelazianami żelaza, kobaltu i niklu przeprowadzono za pomocą spektroskopii impedancyjnej (SI). Wykazano, że materiały hybrydowe charakteryzują się dobrą stabilnością. Warstwy testowano w zakresie temperatur od 283 do 313K. w kontakcie z wodnym roztworem KCl. Wysokie współczynniki dyfuzji wskazują na możliwości wykorzystania układów jako przewodników jonowych.
-
Wytrzymałość połączeń poliuretanowo-stalowych otrzymanych z użyciem kleju cilbond
PublicationPrzedstawiono wyniki badań wytrzymałości na oddzieranie elementów warstwowych poliuretanowo-stalowych połączonych przy użyciu klejuCilbond 45SF. Stalowe płaskowniki o różnej chropowatości pokrywanoklejem Cilbond 45SF i wygrzewano w kilku przyjętych czasach i określonej temperaturze. Na płaskowniki ułożone w stalowej formie wylewano ciekły system poliuretanowy. Po zżelowwaniu polimeru, próbki warstwowe poddawano utwardzeniu w różnych...
-
Structural changes of bacterial cellulose due to incubation in conditions simulating human plasma in the presence of selected pathogens
PublicationBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of medical applications. However, it cannot be used as a biological implant of the circulatory system without checking whether it is biodegradable under human plasma conditions. This work aimed to investigate the BNC biodegradation by selected pathogens under conditions simulating human plasma. The BNC was incubated in simulated biological fluids with or...
-
Pressure-induced flow processing behind the superior mechanical properties and heat-resistance performance of poly(butylene succinate)
PublicationWe propose a pressure-induced flow (PIF) processing method for the simultaneous enhancement of strength, toughness, and heat resistance of biodegradable poly(butylene succinate) (PBS). The pressure and temperature were systematically adjusted to optimize the tensile strength of PBS. Under the optimized processing conditions, the structured PBS was characterized by relatively high strength of 89.5 MPa, toughness of 21.4 kJ·m−2 ,...
-
Biomedical engineering of polysaccharide-based tissue adhesives: Recent advances and future direction
PublicationTissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also...
-
Crystalline Polysaccharides: A Review
PublicationThe biodegradability and mechanical properties of polysaccharides are dependent on their architecture (linear or branched) as well as their crystallinity (size of crystals and crystallinity percent). The amount of crystalline zones in the polysaccharide significantly governs their ultimate properties and applications (from packaging to biomedicine). Although synthesis, characterization, and properties of polysaccharides have been...
-
Chitin and derivative chitosan-based structures — Preparation strategies aided by deep eutectic solvents: A review
PublicationThe high molecular weight of chitin, as a biopolymer, challenges its extraction due to its insolubility in the solvents. Also, chitosan, as the N-deacetylated form of chitin, can be employed as a primary material for different industries. The low mechanical stability and poor plasticity of chitosan films, as a result of incompatible interaction between chitosan and the used solvent, have limited its industrialization. Deep eutectic...
-
Polysaccharide-based electroconductive hydrogels: Structure, properties and biomedical applications
PublicationArchitecting an appropriate platform for biomedical applications requires setting a balance between simplicity and complexity. Polysaccharides (PSAs) play essential roles in our life in food resources, structural materials, and energy storage capacitors. Moreover, the diversity and abundance of PSAs have made them an indispensable part of food ingredients and cosmetics. PSA-based hydrogels have been extensively reviewed in biomedical...
-
Zeolitic imidazolate framework (ZIF-8) modified cellulose acetate NF membranes for potential water treatment application
PublicationIn this study, cellulose acetate (CA)-based nanofiltration membranes, modified with zeolitic imidazole framework-8 (ZIF-8) particles, were prepared with various ZIF-8 contents (0, 0.1, 0.25, 0.5, 1 and 2 wt%), to obtain membranes with improved flux and filtration performance by combining advantages of CA polymer and ZIF-8 metal-organic frameworks. Removal efficiency studies were carried out with bovine serum albumin and two different...
-
Chitin nanowhiskers from shrimp shell waste as green filler in acrylonitrile-butadiene rubber: Processing and performance properties
PublicationIn this work, chitin nanowhiskers with high crystallinity index were obtained from shrimp shells waste using acid hydrolysis method and then comprehensively characterized. Subsequently, the impact of chitin nanowhisker content on processing and performance of acrylonitrile-butadiene rubber based nanocomposites was evaluated. The results showed that the addition of chitin nanowhiskers increased tensile strength and tear strength...
-
Effect of chemical structure on complexation efficiency of aromatic drugs with cyclodextrins: The example of dibenzazepine derivatives
PublicationIt is widely believed that the hydrophobic effect governs the binding of guest molecules to cyclodextrins (CDs). However, it is also known that high hydrophobicity of guest molecules does not always translate to the formation of stable inclusion complexes with CDs. Indeed, a plethora of other factors can play a role in the efficiency of guest–CD interactions, rendering structure-based prediction of the complexation efficiency with...
-
Thin-layer synthesized acrylamide copolymers modified with montmorillonite. Flocculation efficiency evaluation
Publication -
Rigid polyurethane foams modified with ground tire rubber - mechanical, morphological and thermal studies
PublicationRigid polyurethane foams, prepared by a single step method, were modified with the two types of ground tire rubber particles, i.e. untreated and thermo-mechanically reclaimed by using a co-rotating twin screw extruder. The foaming process as well as the structure and the physical, mechanical and thermal properties of the resulting foams were investigated. The presence of ground tire rubber decreased the velocity of polymerization....
-
Thermosensitive composite based on agarose and chitosan saturated with carbon dioxide. Preliminary study of requirements for production of new CSAG bioink.
PublicationThis study introduces a method for producing printable, thermosensitive bioink formulated from agarose (AG) and carbon dioxide-saturated chitosan (CS) hydrogels. The research identified medium molecular weight chitosan as optimal for bioink production, with a preferred chitosan hydrogel content of 40–60 %. Rheological analysis reveals the bioink's pseudoplastic behavior and a sol-gel phase transition between 27.0 and 31.5 °C. The...
-
Stability and physicochemical properties of model salad dressings prepared with pregelatinized potato starch
Publication -
Microwave-assisted silication of potato starch
PublicationSilication of potato starch was performed by microwave irradiation and convectional heating of starch with sodium metasilicate. The study has shown that microwaves offered more selective silication thanconvectional heating. Depending on the dose of metasilicate products of either monoesterification or crosslinking esterification were formed. Increase in the amount of the silicating agent favoured crosslinking of starch. In the...
-
Effect of preparation method on the properties of potato starch acetates with an equal degree of substitution
Publication -
All-natural bio-plastics using starch-betaglucan composites
Publication -
Properties of retrograded and acetylated starch produced via starch extrusion or starch hydrolysis with pullulanase
Publication -
Selected properties of acetylated adipate of retrograded starch
Publication -
Synthesis, chemical structure and properties of cross-linked poly(esterourethanes) based on unsaturated oligo(alkyleneester)diols
PublicationW pracy przedstawiono wyniki badań struktury chemicznej i właściwości nienasyconych oligo(alkilenoestro)dioli oraz syntetyzowanych z ich udziałem poli(estrouretanów). Strukturę oligomeroli oraz poliuretanów ustalono w oparciu o wyniki badań FTIR, NMR, analizę elementarną. Właściwości poli(estrouretanów) określono przez pomiary stabilności termicznej, analizę termomechaniczną oraz obliczenia ciężaru cząsteczkowego łańcuchów polimerowych...
-
Esterification of starch with sodium selenite and selenate
Publication -
Carboxymethyl cellulose–gelatin complexes
Publication -
Electrosynthesis of potato starch–whey protein isolate complexes
Publication -
The influence of 4,4'-bis(6-hydroxyhexoxy)biphenyl moieties on properties of polyurethanes based on 4,4'-methylenebis(cyclohexyl isocyanate)
PublicationZsyntetyzowano dwie serie poliuretanów z 4,4'-bis(6-hydroksyheksyloksy)bifenylu (BH6), poliadypinianu 1,6-heksylenu i diizocyjanianu 4,4'-dicykloheksylometanu o udziałach izomeru trans, wynoszącym odpowiednio 16 i 46%. Badano wpływ udziału wagowego (u) małocząsteczkowego diolu(BH6)w odniesieniu do sumy mas komonomerów diolowych, na właściwości uzyskanych poliuretanów metodami DSC, DTA, TGA, mikroskopii polaryzacyjnej, WAXS, DMTA...
-
Microwave-assisted preparation of potato starch silicated with silicic acid
PublicationApplication of microwave irradiation for the silication of granular potato starch with silicic acid, and the properties of silicated starch were investigated. Potato starch was esterified on 20 min microwave irradiation of starch with silicic acid, applying the power of 450 or 800Wand, for comparison, on 120 min convectional heating of the reagent blend at 100 ◦C. The degree of esterification and the reaction efficiency did not...
-
Microwave-assisted synthesis of zinc derivatives of potato starch
PublicationZincatated potato starch was prepared in a solid-state, microwave-assisted reaction using generated in situ sodium tetrahydroxozincate [Na2Zn(OH)4]. For comparison, zincatation of starch was also carriedout on convectional heating. Depending on the irradiation conditions, the products of either mono- or crosslinking esterification were formed. Higher power applied at shorter exposition offered products ofmonoesterification, and...
-
Spectroscopic insight into supramolecular assemblies of boric acid derivatives and β-cyclodextrin
Publication -
Novel hydrophilic carboxymethyl starch/montmorillonite nanocomposite films
Publication -
Carboxymethylated starch and cellulose derivatives-based film as human skin equivalent for adhesive properties testing
Publication