Search
Filters
total: 2474
-
Catalog
displaying 1000 best results Help
Search results for: X65 steel
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublicationThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublicationThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Corrosion degradation impact on mechanical properties of structural steel
PublicationRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
Modeling the application of steel slag in stabilizing expansive soil
PublicationThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Experimental tests of steel double-type balcony connections
PublicationThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublicationW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Thermal Fatigue Influence of Laser Treated Tool Steel Surface
Publication -
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publication -
Experimental research of the stability of steel cylindricalshell subjected to circumferential compression
PublicationAt the Department of Metal Structures Gdańsk University of Technology, experiments have been performed on the stability of shell of steel cylindrical models. The experiments have been carried on a test bench built at the Department. The design based on other test benches which were created in the past by other scientists, where modernized by the courtesy of companies that offer modern solutions. The test bench enables to generate...
-
Search for optimum geometry of selected steel sandwich panel joints
PublicationZastosowanie stalowych paneli typu sandwich w konstrukcjach okrętowych wymaga rozwiązania wielu problemów. Jednymi z trudniejszych zagadnień związanych z tymi nowymi strukturami są połączenia pomiędzy panelami oraz między panelami i konstrukcją innego typu. Artykuł przedstawia poszukiwanie optymalnej geometrii połączenia typu panel-panel w układzie wzdłużnym, przy użyciu parametrycznego modelu w programie ANSYS. Poszukiwano konfiguracji...
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublicationNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Fatigue life tests of steel laser-welded sandwich structures
PublicationW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
Tests of local strains in steel laser - welded sandwich structure
PublicationW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
The influence of plastic deformation on the magnetoelastic properties of the CSN12021 grade steel
PublicationWłasności magnetosprężyste materiałów są silnie modyfikowane przez zmiany struktury dyslokacyjnej, które są wynikiem procesów deformacji plastycznej. Zmiany te mogą być wykorzystane jako podstawa do opracowania metody nieniszczącej oceny stopnia deformacji materiału.Jak dotychczas zaproponowane zostały różne metody, oparte na pomiarach pętli histerezy magnetycznej czy też natężenia magnetycznego efektu Barkhausena. Artykuł porównuje...
-
Mechanical properties and corrosion resistance of dissimilar stainless steel welds
PublicationW artykule przedstawiono właściwości mechaniczne oraz odporność korozyjną doczołowych złączy różnoimiennych stali odpornych na korozję, austenitycznej 316L oraz duplex 2205. Blachy o grubości 15 mm spawano automatycznie łukiem krytyn z różnymi energiami liniowymi. Wykazano, że właściwości mechaniczne złączy spełniają wymagania okrętowych towarzystw klasyfikacyjnych, natomiast najbardziej narażoną strefą złącza na działanie korozji...
-
Efect of ageing on microstructure and impact properties of 9Cr-1Mo steel
PublicationBadano wpływ długotrwałego starzenia na mikrostrukturę i właściwości udarnościowe trzech przemysłowych wytopów stali typu 9Cr-1Mo. Wczesniejsze badania wykazały, że w stali 9Cr-1Mo starzonej w 550C przez 10 000 godzin występuje kruchość odpuszczania, a przy dłuższych czasach ekspozycji tworzy się krucha faza Lavesa (FeCr)2Mo na granicach ziaren. Powoduje to wzrost teperatury przejściowej kruchości oraz spadek energii łamania powyżej...
-
Experimental and numerical studies of double corrugated steel arch panels
Publication -
Estimation of the parameters of the discrete model of a steel–concrete composite beam
Publication -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publication -
Influence of stress on oxidation behaviour of carbon steel studded coil.
PublicationAnalizowano awarię wężownicy kołkowej ze stali węglowej pracującej przez 10 lat w środowisku przegrzanej pary w temperaturze 290ºC i ciśnieniu 0,67 MPa. Obserwacje mikroskopowe powierzchni i przekroju rury ukazały drobne pęknięcia w ściance wynikające z procesu selektywnego utleniania. Zastosowano metodę elementów skończonych w celu ustalenia zależności postępu korozji od ciśnienia i obciążenia cieplnego.
-
Assessment of structural changes in IN-519 cast steel reformer tubes.
PublicationPrzedstawiono zmiany struktury rur katalitycznych ze staliwa austenitycznego IN-519 po długotrwałej eksploatacji w reformerze metanu.
-
Hydrogen delayed cracking of high-strength 14hnmbcu steel in seawater
PublicationOceniano podatność na niszczenie wodorowe stali o wysokiej wytrzymałości i jej połączeń spawanych przy stałym obciążeniu w wodzie morskiej. Badania przeprowadzono na próbkach okrągłych z karbem w środowisku wody morskiej przy potencjale korozyjnym oraz przy polaryzacji katodowej. Badano stal gatunku 14HNMBCu o minimalnej granicy plastyczności 690 MPa oraz jej połączenia spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą...
-
Cementite transformation in low carbon steel under the influence of sulphur.
PublicationBadano cementyt (węglik Fe3C) w przemysłowym gatunku stali niskowęglowej po długotrwałej eksploatacji w benzynie ciężkiej, zawierającej 0,3 ppm siarki, o temperaturze 200-220C. Wykazano, że cementyt na powierzchni i we wnętrzu stali ulega przemianie w niestabilną, quasi-krystaliczną fazę wzbogaconą w siarkę i pierwiastki domieszkowe a zubożoną w żelazo. Przemiana cementytu i rozpad zdegradowanej fazy związana jest z uwolnieniem...
-
Hydrogen degradation of the 26H2MF alloy steel in H2SO4 and hydrocarbon environments.
PublicationSTAL 26H2MF ZOSTALA PODDANA RÓZNEJ OBRÓBCE CIEPLNEJ, PO KTÓREJ UZYSKAŁA ONA RÓŻNĄ MIKROSTRUKTURĘ ORAZ CHARAKTER PRZEŁOMU. WYKONANO PRÓBY POWOLNEGO ODKSZTAŁCANIA W ROZCIEŃCZONYM KWASIE SIARKOWYM, PALIWIE CIĘZKIM I PRZEPRACOWANYM OLEJU SILNIKOWYM PRZEPRACOWANYM.
-
Poli-optimization of selected variants of steel sandwich panels connections
PublicationPanele kompozytowe odgrywają coraz większą role w różnorodnych zastosowaniach inżynierskich. Jednym z zagadnień kluczowych dla możliwości aplikacyjnych są połączenia między cienkościennymi formami w układzie wzdłużnym i poprzecznym. Praca prezentuje wyniki polioptymalizacji numerycznej wybranych połączeń stalowych paneli typu sandwich.
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublicationEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
The response of three colliding models of steel towers to seismic excitation
PublicationA number of past and recent observations have confirmed that collisions between adjacent, insufficiently-separated structures occurring as a result of seismic excitation (structural pounding) may result in serious damage to structural elements and can even lead to their total destruction. This paper summarises the results obtained from a shaking table experimental study which investigated structural pounding between three adjacent...
-
NUMERICAL ANALYSIS OF RUBBER BUMPERS INFLUENCE ON THE COLLIDING STEEL STRUCTURES
PublicationProblem of collisions of neighbouring structures is one of the important issues related to the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of numerical investigation of dynamic behavior of closely-separated steel structures under seismic excitation. Modal and transient...
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublicationTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublicationUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Influence of pitting corrosion on strength of steel ships and offshore structures
PublicationPraca dotyczy wpływu korozji wżerowej na własności mechaniczne stali o zwykłej i podwyższonej wytrzymałości oraz na wytrzymałość stalowych konstrukcji przy obciążeniach statycznych i quasi- statycznych. Artykuł oparty jest głównie na japońskich publikacjach. W próbie rozciągania, korozja wżerowa obniża nieznacznie obciążenie odpowiadające granicy plastyczności Re(nieznacznie) i wytrzymałości na rozciąganie Rm (silniej, redukuje...
-
The degradation mechanisms of a nanobainitic steel under cavitation erosion conditions
Publication -
Evaluation of recycled tyre steel fibres adhesion to cement matrix
Publication -
Framework for Structural Health Monitoring of Steel Bridges by Computer Vision
PublicationThe monitoring of a structural condition of steel bridges is an important issue. Good condition of infrastructure facilities ensures the safety and economic well-being of society. At the same time, due to the continuous development, rising wealth of the society and socio-economic integration of countries, the number of infrastructural objects is growing. Therefore, there is a need to introduce an easy-to-use and relatively low-cost...
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublicationConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
The Effectiveness of Polymer Damper in Damage Reduction of Temporary Steel Grandstand
PublicationA large number of accidents involving damage of temporary grandstands during different types of events were observed in the past. The aim of the paper is to analyse numerically the effectiveness of a polymer damper in damage reduction of a temporary steel scaffolding grandstand exposed to dynamic load due to jumping. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Application of polymer element in reduction of temporary steel grandstand vibrations
PublicationThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...
-
Experimental study on earthquake-induced pounding between steel structures
PublicationPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Influence of Material Thickness on the Ductile Fracture of Steel Plates for Shipbuilding
PublicationIn the shipbuilding industry, the risk of brittle fractures is relatively high because some units operate in arctic or subarcticzones and use high thickness (up to 100 mm) steel plates in their structures. This risk is limited by employing certifiedmaterials with a specific impact strength, determined using the Charpy method (for a given design temperature) and byexercising control over the welding processes (technology qualification,...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...