Search
displaying 1000 best results Help
Search results for: displacements of chimney
-
Displacements of chimney in the light of computer calculations and surveying
PublicationThe article presents the numerical analysis of reinforced concrete chimney displacements, which was carried out geodetic measurements.
-
Improvement of the Chimney Effect in Stack Ventilation
PublicationThe article is focused on the airflow in a ventilation system in a building. The work examines the methods which enhance the chimney effect. In this paper, three cases with different chimneys were analyzed for the full-scale experiment. These cases were characterized by different geometrical and material parameters, leading to differences in the intensity of the ventilation airflow. The common denominator of the cases was the room...
-
Reduction of steel chimney vibrations with a pendlum damper.
PublicationKarman vortices observed around chimneys may induce dangerous structural vi-brations at certain wind velocities. The aim of this paper is to analyse theeffectiveness of pendulum damper in vibration reduction of a steel chimney. A two degree-of-freedom system is used to model the behaviour of the struc-ture equipped with a damper. The results of the study show that the use of pendulum with tuned frequency leads to significant...
-
Application of the Chimney Cap as a Method of Improving the Effectiveness of Natural Ventilation in Buildings
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the air inside a building fresh. A prediction of the performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long-term cost savings. The worst time in terms of the efficiency of natural ventilation is the spring-autumn transition period [7]. In...
-
Anti‐corrosion protection of chimneys and flue gas ducts
Publication -
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublicationOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Comparison of Different Measurement Techniques as Methodology for Surveying and Monitoring Stainless Steel Chimneys
PublicationThe measurement of a chimney axis is an engineering geodesy task. These measurements allow to assess the technical condition of chimneys and are usually carried out for reinforced concrete chimneys. When measuring high chimneys, the main problem may be the need to go a long distance to take a measurement. The surface of the chimney can also be problematic because it can absorb so much light from the range finder that total station...
-
DETERMINATION OF VERTICAL DISPLACEMENTS IN RELATIVE MONITORING NETWORKS
PublicationThe problem of determining displacements of objects is an important and current issue, in particular in terms of operational safety. This is a requirement that covers geodetic, periodic control measurements in order to determine horizontal and vertical displacements. The paper is focused on the analysis of vertical displacements. Geodetic measurements and their interpretation allow to reduce the risk of possible structural catastrophes....
-
Statistical significance of displacements in heterogeneous control networks
PublicationThis paper proposes a modification of the classical process for evaluating the statistical significance of displacements in the case of heterogeneous (e.g. linear-angular) control networks established to deformation measurements and analysis. The basis for the proposed solution is the idea of local variance factors. The theoretical discussion was complemented with an example of its application on a simulated horizontal control...
-
Study of displacements of a bridge abutment using FEM
PublicationSteel sheet piles are often used to support excavations for bridge foundations. When they are left in place in the permanent works, they have the potential to increase foundation bearing capacity and reduce displacements; but their presence is not usually taken into account in foundation design. In this article, the results of finite element analysis of a typical abutment foundation, with and without cover of sheet piles, are presented...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublicationThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Displacement control in PWK-type pumps
PublicationW referacie zaprezentowano konstrukcję mechanizmu sterowania wydajnością zastosowanego w pompach z rozrządem krzywkowym typu PWK. Przedstawiono wyniki wstępnych badań prototypu PWKZ-78 oraz komputerową analizę zjawisk zachodzących w komorze cylindrowej pompy.
-
Displacement control in PWK-type pumps
PublicationThe most important, strategic goal however is creation of the variable displacement version of the new pump PWK. Thanks to full discharge of it's commutation mechanism from hydrostatic forces the variable pump can be directly controlled by low-energy actuator like proportional electromagnet or stepping motor. It means that costly and complicated hydraulic servomechanism (applied in all present variable displacement pumps) is no...
-
Chime
Journals -
Design of Microwave-Based Angular Displacement Sensor
PublicationThis letter presents a novel microwave-based rotation sensor having a wide dynamic range to detect and measure the angular displacement in terms of the change in resonant frequency. The proposed sensor is based on the microstrip technology, where a rotor comprised of a complementary splitring resonator (CSRR) placed on the ground plane of the microstrip line is free to rotate around its axis. The mechanical rotation of CSRR determines...
-
Investigations of transverse stability of semi-displacement ships
PublicationPrzedstawiono wyniki eksperymentalnych badań modelowych poprzecznej stateczności jednostek półślizgowych, których celem było określenie wpływu prędkości oraz parametrów kształtu kadłuba na stateczność poprzeczną. Na podstawie wyników badań opracowano algorytmy, uwzględniające zmiany ramienia prostującego w funkcji prędkości, kąta przechyłu i parametrów geometrycznych kadłuba które mogą być wykorzystane do oceny stateczności poprzecznej...
-
Multifunctional Bandpass Filter/Displacement Sensor Component
PublicationThis paper presents the design and realization of a multifunctional bandpassfilter/displacement-sensor using an edge-coupled microstrip bandpass filter loaded by a pair of split ring resonators (SRRs). It is shown that while the structure acts as a bandpass filter at its operating frequency, the phase of the reflection coefficient from a movable loading resonator at the resonance frequency of the resonator can be used for displacement...
-
Accuracy Analysis of Determination the Vertical Displacements in Unstable Reference System
PublicationMeasurements of horizontal and vertical displacements are carried out mostly based on reference points identified as fixed. In surveying practice there may be some situations in which there is not possible to perform the measurements with reference to stable points or the difficulties in identification of points’ stability may arise. Accuracy analysis based on the covariance matrices have a special role in this process. In presented...
-
Application of Adomian decomposition method in analysis of displacements ofrandom subsoil
PublicationW pracy przedstawiono metodę dekompozycji Adomiana oraz jej zastosowanie do rozwiązania zagadnienia losowego ośrodka gruntowego. Rozpatrzono ważką warstwę gruntu, posadowioną na nieodkształcalnym podłożu, poddaną działaniu równomiernie rozłożonego pionowego obciążenia zewnętrznego. Przyjęto, że ośrodek jest sprężysty, a jego parametry są funkcjami losowymi. Uzyskano przybliżone rozwiązanie analityczne wraz z oceną zakresu jego...
-
Field investigations of stack ventilation in a residential building with multiple chimneys and tilted window in cold climate
PublicationArtykuł przedstawia wyniki pomiarów wykonanych w budynku mieszkalnym w północnej Polsce w zimnym klimacie podczas zimy i lata. Budynek zawierał kominy i uchylne okna. Pomierzono lokalne i wewnętrzne warunki klimatu oraz prędkości powietrza. Zaproponowano zmodyfikowany model uchylnych okien oparty na modelu wentylacji jednokierunkowej.
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublicationDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Distribution of the displacement sequence of an orientation preserving circle homeomorphism
PublicationIn some applications not only the knowledge of the behaviour of trajectories of a map is important, but also their displacements. We describe in detail the distribution of elements of the displacement sequence along a trajectory of an orientation preserving circle homeomorphism ϕ with irrational rotation number ϱ(ϕ). The values of displacement are dense in a set which depends on the map γ (semi-)conjugating ϕ with the rotation...
-
Geometric working volume of a satellite positive displacement machine
PublicationThis article describes a method for determining the geometric working volume of satellite positive displacement machines (pump and motor). The working mechanism of these machines is satellite mechanism consisting of two non-circular gears (rotor and curvature) and circular gears (satellites). Two variants of the satellite mechanism are presented. In the first mechanism, the rolling line of the rotor is a sinusoid "wrapped" around...
-
New concept of drilling auger for displacement pile installation
PublicationIn 2020, a new version of the screw displacement auger for pile installation in soil was developed and patented in Poland. It was named DPDT (Displacement Pile Drilling Tool). The general aim of its development was to reduce the soil resistances to the auger during screwing into the ground while maintaning a good load-bearing capacity for the screw displacement piles. The “DPDT-Auger” prototype was tested as a scaled-down model...
-
On the regularity of the displacement sequence of an orientation preserving circle homeomorphism
PublicationWe investigate the regularity properties of the displacemnet sequence of an orientation preserving circle homeomorphism. is rational, then ηn(z) is asymptotically periodic with semi-period q. This
-
Nanoparticles displacement analysis using optical coherence tomography
PublicationOptical coherence tomography (OCT) is a versatile optical method for cross-sectional and 3D imaging of biological and non-biological objects. Here we are going to present the application of polarization sensitive spectroscopic OCT system (PS-SOCT) for quantitative measurements of materials containing nanoparticles. The PS-SOCT combines the polarization sensitive analysis with time-frequency analysis. In this contribution the benefits...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Displacements of Cable-Stayed Bridge Measured With The Use of Traditional And Modern Techniques
Publication -
Modeling of cutter displacements during ball end milling of inclined surfaces
Publication -
The analysis of instantaneous tool displacements during precise ball end milling
Publication -
Machined Surface Roughness Including Cutter Displacements in Milling of Hardened Teel
Publication -
Coastal Cliffs Monitoring and Prediction of Displacements Using Terrestial Laser Scanning
PublicationCoastal cliffs are very sensitive to degradation caused by erosion and abrasion. Thus, it is very important to monitor susceptibility of the cliffs in terms of slope angles and ground fall resulting from vertical morphology of the cliffs. The results could be used for example to establish the boundaries of the safe investments zone or retreat infrastructure buildings in case of real threat such as degradation of the objects of...
-
Experimental verification of visual method for measuring displacements of contact line elements
PublicationThe increase of rail vehicles speed, as well as the increase of their power, puts high demands on the power delivery system for traction vehicles The most critical point in the vehicle's power supply circuit is the contact between the current collector and contact wires. Ensuring a reliable co-operation of the current collector and contact line, requires technical development...
-
Analyses of static displacements of a spindle apllied in typical circular sawing machines
PublicationW pracy przedstawiono analizę właściwości statycznych wrzeciona stosowanego w typowych pilarkach tarczowych. Zdefiniowano umowną oś obrotu wrzeciona pilarki tarczowej, która odpowiada geometrycznemu środkowi otworu piły tarczowej. W obliczeniach wyznaczono przemieszczenia umownej osi obrotu wrzeciona, wskaźnik sztywności wrzeciona oraz przemieszczenie poprzeczne piły.
-
Application of DIC technique to concrete - study on objectivity of measured surface displacements
PublicationArtykuł omawia wyniki pomiarów szerokości lokalizacji odkształceń na powierzchni betonu podczas zginania belek. Wykonano obszerne studia nad obiektywnością pomierzonych przemieszczeń w betonie. Opracowano własna metodę do obliczeń szerokości lokalizacji.
-
Identification of Unstable Reference Points and Estimation of Displacements Using Squared Msplit Estimation
PublicationThe article presents a new version of the method for estimating parameters in a split functional model, which enables the determination of displacements of geodetic network points with constrained datum. The main aim of the study is to present theoretical foundations of Msplit CD estimation and its basic properties and possible applications. Particular attention was paid to the efficacy of the method in the context of geodetic...
-
Application ofMsplitestimation to determine control points displacements in networks with unstable reference system
Publication -
Precision surface characterization for finish cylindrical milling with dynamic tool displacements model
Publication -
Assessing the Significance of Displacements Using Local Coefficients of Variance as an Alternative to the Classical Approach
PublicationThe safety of use of civil engineering structures remains an important issue that is approached by various sciences. Due to this fact, geodetic control measurements are conducted with the purpose of identifying threats connected with the potential displacement of structural elements. In this context, the authors discuss issues connected with determining the displacements of controlled points located in the studied object in a three-dimensional...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
The methodology of design of satellite working mechanism of positive displacement machine
PublicationIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
DISPLACEMENT MEASUREMENTS DURING LOAD TESTING OF THE RAILWAY ARCH BRIDGE
Publication -
Motion laws synthesis for cam mechanisms with multiple follower displacement
Publication -
The analysis of soil resistance during screw displacement pile installation
PublicationThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Fiber optic displacement sensor with signal analysis in spectral domain
PublicationIn this paper, a study of a low-coherence fiber optic displacement sensor is presented. The sensor consisted of a broadband source whose central wavelength was either at 1310 nm or 1550 nm, a sensing Fabry-Pérot interferometer operating in reflective mode and an optical spectrum analyzer acting as the detection setup. All these components were connected by a single-mode fiber coupler. Metrological parameters of the sensor were...
-
Displacement measurements during load testing of railway arch bridge
PublicationThe paper discusses issues concerning load tests carried out on a twin-track, arch railway bridge over the Martwa Wisla river in Gdansk. Currently, it is the bridge with the longest span in its class in Poland. The load-bearing structure consists of three no-hinge arches and an orthotropic deck suspended from them. The studies of the structure assumed the performing of static and dynamic tests. The paper presents the method for...
-
Methods for displacement and rotation measurements of individual Taylor-Schneebeli grains.
PublicationW artykule przedtawiono autorską metodę pomiaru przemieszczeń oraz obrotów cząstek ośrodka analogowego Taylor-Schneebeli oraz propozycję interpretacji badań.
-
Microwave Alignment and Displacement Sensors in Groove Gap Waveguide Technology
PublicationThis paper is aimed at presenting highly sensitive microwave displacement and alignment sensors. With this goal, the method of realizing mechanically tunable cavity resonators in groove gap waveguides technology is presented. The resonance frequency of the cavity is then used for displacement sensing. It is also demonstrated that the symmetry properties of a pair of groove gap waveguide cavities can be used to improve the robustness...
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublicationThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
Determination of vertical displacements by using the hydrostatic levelling systems with the variable location of the reference sensor,
PublicationAbstract: In this paper, the author proposed a new method for determination of vertical displacements with the use of hydrostatic levelling systems. The traditional method of hydrostatic levelling uses a rule in which a position of reference sensor is stable. This assumption was not adapted in the proposed method. Regarding the issue mentioned above, the reference sensor is treated in the same way as the others sensors that measure...