Wyszukiwarka
Filtry
wszystkich: 671
wybranych: 608
Wyniki wyszukiwania dla: CONCRETE
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublikacjaEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublikacjaAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Unfolding new values in the landscape of conflict
PublikacjaThe main objective of the paper is to investigate how the conflict quality of landscape can be used as its asset and potential for creating new values. Like mediation between different overlapping archaeologies offers a basis for the perception of place in the chronology of time, the mediation between conflicted areas creates a capacious zone for enhancing the unique quality of landscape in its architectural, social, cultural and...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublikacjaThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublikacjaThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublikacjaRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publikacja-
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublikacjaDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Analiza przyczepności prętów żebrowanych w betonie metodą pull-out na próbkach centrycznych i mimośrodowych
PublikacjaArtykuł dotyczy analizy przyczepności żebrowanego stalowego pręta zbrojeniowego w betonie. Celem pracy była ocena wpływu położenia pręta w betonowym bloku na lokalną zależność naprężenie przyczepności-poślizg. Podjęto także próbę numerycznej symulacji przeprowadzonych eksperymentów w programie ABAQUS. Analizę doświadczalną przeprowadzono za pomocą testu pull-out na dwóch rodzajach próbek – centrycznych i mimośrodowych w dwóch wariantach,...
-
Diagnostyka ultradźwiękowa mostowej belki prefabrykowanej typu T metodą młoteczkową
PublikacjaZastosowanie prefabrykacji w budowie obiektów mostowych pozwala optymalizować zużycie energii i materiałów i tym samym redukować koszty budowanego obiektu. Prefabrykowane belki sprężone mogą występować jako elementy kablobetonowe wykonywane bezpośrednio na placu budowy lub powstawać w zakładzie prefabrykacji jako elementy strunobetonowe. Elementy prefabrykowane wytwarzane w warunkach przemysłowych muszą spełniać wymagania wysokiej trwałości,...
-
Instalacja oświetleniowa w zbiorniku wody "Stary Sobieski" - rozważania o spektakularnym zabytku techniki
PublikacjaArtykuł przedstawia efekty badań autora nad niezwykle okazałą, ponad stuletnią instalacją elektryczną, która zachowała się w zabytkowym obiekcie infrastruktury wodociągowej w niemal 100% oryginalnej formie (nie licząc częściowej dewastacji). Jest to rzadki przykład tego rodzaju zabytku, ponieważ obiekty tego typu i w tym wieku zwykle podlegały modernizacji na przestrzeni lat albo, po wyłączeniu z eksploatacji zostały całkowicie...
-
FEM modelling of screw displacement pile interaction with subsoil
PublikacjaPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublikacjaThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
Building damage due to structural pounding during earthquakes
PublikacjaEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublikacjaThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Potential Impact of Waterway Development on Cultural Landscape Values: The Case of the Lower Vistula
PublikacjaThe northern (“lower”) section of the Vistula is on the route of two international waterways—E70 and E40. However, the current condition of the riverbed prevents larger vessels from passing through. Plans for the waterway date back to the beginning of the 20th century. Following Poland’s ratification of the European Agreement on Main Inland Waterways of International Importance in 2017, the general concept has been transformed...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublikacjaThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Fragility analysis of structural pounding between adjacent structures arranged in series with various alignment configurations under near‑field earthquakes
PublikacjaA major cause of local to total damages is related to structural pounding in a large number of past earthquakes. In general, these collisions take place as a result of differences in the dynamic characteristics of the colliding structures. To acquire a better perception of the behavior of structures, in this paper, three structures featuring different heights are modeled in series and with various configurations next to each other...
-
The long-term properties of mineral-cement-emulsion mixtures
PublikacjaThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
DYNAMIC ANALYSIS OF THE RAILWAY BRIDGES IN POLAND WITH REGARDS TO HIGH-SPEED TRAINS PASSAGE ADJUSTMENT
PublikacjaThe dynamic analysis of the railway bridge in Tczew was carried out in the article as an example of such bridges adaptation suitability to handle high-speed trains. Calculations of railway bridges are greatly complicated and labor-consuming. The bridge model and a rolling stock passage simulation were developed in the SOFISTIK software. Three types of elements were used for the correct mapping of the structure in the calculation...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublikacjaDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
WERYFIKACJA KONCEPCJI PRZEGUBÓW PLASTYCZNYCH PROJEKTOWANYCH NA ODZIAŁYWANIA SEJSMICZNE WIADUKTU V6 OBWODNICY ISTAMBUŁU
PublikacjaW pracy zawarto wyniki analiz betonowego wiaduktu V6 budowanego w ciągu obwodnicy Istambułu w Turcji realizowanego w ramach projektu Northern Marmara Highway. Przeprawę stanowią dwie niezależne nitki o skrzynkowym przekroju poprzecznym i szerokości 22,00 m. Schemat statyczny obiektu to belka dziewięcioprzęsłowa o długości całkowitej 446,86 m oparta na podporach słupowych o zmiennej sztywności (rys.1) i wysokościach zmieniających...
-
Automated Reasoning Based User Interface
PublikacjaMotivation: The ability to directly trace how requirements are implemented in a software system is crucial in domains that require a high level of trust (e.g. medicine, law, crisis management). This paper describes an approach that allows a high level of traceability to be achieved with model-driven engineering supported by automated reasoning. The paper gives an introduction to the novel, automated user interface synthesis in...
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublikacjaThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Measurements of Thermal Conductivity of LWC Cement Composites Using Simplified Laboratory Scale Method
PublikacjaThe implementation of low-energy construction includes aspects related to technological and material research regarding thermal insulation. New solutions are sought, firstly, to reduce heat losses and, secondly, to improve the environment conditions in isolated rooms. The effective heat resistance of insulating materials is inversely proportional to temperature and humidity. Cement composites filled with lightweight artificial...
-
Probabilistic seismic assessment of RC box-girder highway bridges with unequal-height piers subjected to earthquake-induced pounding
PublikacjaThis paper uses the probabilistic seismic assessment to study the effects of pounding and irregularity on the seismic behavior of typical concrete box-girder bridges with four levels of altitudinal irregularity. To extend the results for all bridges in the same class, uncertainty related to the earthquake, structural geometries, and materials are considered. Pounding is likely to take place in two cases: the first one concerns...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Pile Model Tests Using Strain Gauge Technology
PublikacjaOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublikacjaPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublikacjaThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
Dietary behaviour and physical activity policies in Europe: learnings from the Policy Evaluation Network (PEN)
PublikacjaThe European Policy Evaluation Network (PEN), initiated in autumn 2018, aimed at advancing the evidence base for public policies impacting dietary behaviour, physical activity and sedentary behaviours in Europe. This is needed because non-communicable diseases—the leading cause of global mortality—are substantially caused by physical inactivity and unhealthy dietary behaviours, which in turn are driven by upstream factors that...
-
The rigid and flexible road pavements in terms of life cycle costs
PublikacjaThe cost of road pavement construction, its durability and reliability depends on many factors, including: the scope and detail of the technical design, quality of work but also the scope of works related to its maintenance, conservation and operation. Determining the amount of rational expenses, in terms of the life cycle cost of the pavement, requires determination and consideration of the above issues, already at the planning...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublikacjaMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Nonlocal Models of Plates and Shells with Applications in Micro- and Nanomechanics
PublikacjaNowadays, the use of small-scale structures in micro/nanomachines has become more and more widespread. The most important applications of such small-sized parts are in micro-electro-mechanical systems (MEMS) as well as nano-electro-mechanical systems (NEMS) as actuators, sensors, energy harvesters. For example, nanosensors are nanoscale devices that measure physical quantities and convert these to signals that can be detected and...
-
Generating actionable evidence from free-text feedback to improve maternity and acute hospital experiences: A computational text analytics & predictive modelling approach
PublikacjaBackground Patient experience surveys are a key source of evidence for supporting decision-making and quality improvement in healthcare services. These surveys contain two main types of questions: closed and open-ended, asking about patients’ care experiences. Apart from the knowledge obtained from analysing closed-ended questions, invaluable insights can be gleaned from free-text data. Advanced analytics techniques are increasingly...
-
Experimental study on earthquake-induced pounding between steel structures
PublikacjaPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Guided waves for nondestructive diagnostics of embedded waveguides
PublikacjaThe thesis concentrates on comprehensive theoretical, numerical and experimental analysis of guided wave propagation in bars embedded in concrete or mortar. The investigations are focused on a particular type of objects representing a laboratory model of a ground anchor. Complex description of wave propagation phenomena in partially embedded bars is given and its application in...
-
Composite as a Material of the Future in the Era of Green Deal Implementation Strategies
PublikacjaComposite materials have become synonymous with modernity, desired in nearly every aspect of our daily lives, from simple everyday objects to sanitary facilities, pipelines, the construction of modern sewer networks, their renovation, water supply, and storage reservoirs, to complex structures—automotive, planes, and space science. Composites have seen a considerable rise in attention owing to their characteristics, durability,...
-
Stan graniczny nośności dźwigara żelbetowego mostu na zginanie według norm PN-EN 1992-2 oraz PN-S-10042:1991
PublikacjaPraca włącza się w bogaty w ostatnich latach w krajowym piśmiennictwie nurt porównań dwóch generacji norm projektowania mostów z betonu: polskiej - wycofanej, aczkolwiek powszechnie stosowanej oraz europejskiej – wciąż jeszcze wdrażanej do praktyki projektowej. Nowością w stosunku do dotychczasowych publikacji polskich jest szersze ujęcie różnic pomiędzy obydwiema generacjami norm. Poza rozpatrywanymi przez wielu autorów różnicami...
-
Regenarative tourism – between theory and practice
PublikacjaPurpose: The aim of this article is to present a shift in thinking in terms of implementing the systems and practices needed to transition to a regenerative approach in tourism. The article aims to provide concrete ways to change thinking and move towards a regenerative paradigm in the tourism industry. Design/methodology/approach: This viewpoint paper defines regenerative tourism and explores its principles and the possibilities...
-
ASSESSMENT OF CLIFF STABILITY AFTER THE DEMOLITION OF THE ENGINEERING FACILITIES
PublikacjaAs a part of an experiment, cliff in Gdynia Redlowo (southern coast of Baltic Sea, Gdansk Bay) was measured using terrestrial laser scanner. The main reason for taking up the subject of the Orlowo Cliff’s stability was a decision about controlled removal one of the war fortification elements. The main purpose of that analysis was to specify suitability of laser scanning in determination of slope’s stability after a violent event....
-
Smart Materials in Architecture: Useful Tools with Practical Applications or Fascinating Inventions for Experimental Design?
PublikacjaFor at least several decades smart or so-called intelligent materials, being the result of great advancements in material engineering, appear in architecture in different applications. Most of them are called "smart" because of their inherent properties: a real-time response to environmental stimuli. There are also those considered to be "smart" due to smart design: their original structure or the composition of their materials...
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublikacjaCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...