Filtry
wszystkich: 5061
wybranych: 4701
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EMPIRICAL INFLUENCE FUNCTION
-
The Influence of Thin Gold Electrodes on the High-Temperature Impedance of Oxide Glasses
PublikacjaThe influence of thin gold electrodes on the electrical measurements of glasses at high temperatures was studied using impedance spectroscopy. The impedance was measured several times over a wide frequency range from 10 mHz to 1 MHz and the temperature ranged from 213 to 673 K under air and nitrogen atmospheres. The results showed a drop in the conductivity of more than an order of magnitude at a temperature around 603 K during...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublikacjaThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublikacjaThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublikacjaIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublikacjaThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
-
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
Publikacja -
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
PublikacjaThis paper describes an open and extensive validation study carried out by the Specialist Committee on Ships in Operation at Sea (SOS) of the International Towing Tank Conference (ITTC) on the newly developed SHOPERA-NTUA-NTU-MARIC (SNNM) wave-added resistance prediction method. The SNNM method aims at a simple, fast and transparent determination of the added resistance in regular waves of arbitrary encounter directions, even when...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublikacjaThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Influence of high temperature air-steam mixture application on time wood drying process
PublikacjaThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship structures. Part I: pitting corrosion of ship structures.
PublikacjaThe paper is a literature survey focused on pitting corrosion and its influence on fatigue of ship and offshore steels. Mechanisms of short- and long-term pitting corrosion in marine environment have been described including pit nucleation and growth phases. Some models of pit growth versus time of exposure have been presented. Some factors which influence the pit growth have been discussed briefly.
-
Mass spectrometry based identification of geometric isomers during metabolic stability study of a new cytotoxic sulfonamide derivatives supported by quantitative structure-retention relationships
PublikacjaA set of 15 new sulphonamide derivatives, presenting antitumor activity have been subjected to a metabolic stability study. The results showed that besides products of biotransformation, some additional peaks occurred in chromatograms. Tandem mass spectrometry revealed the same mass and fragmentation pathway, suggesting that geometric isomerization occurred. Thus, to support this hypothesis, quantitative structure-retention relationships...
-
The role of clusters as collective actors in the energy transformation: the case of Mazovia Cluster ICT
PublikacjaPurpose – In our paper we aim to show the possibilities of implementing the idea of sustainability in the context of energy transformation using the concept of an industrial cluster. The implementation of the idea of sustainability is of particular importance from the perspective of the functioning of the meta-organisations involved in the implementation and promotion of decarbonisation processes. Industrial clusters, as collective...
-
ARTIFICIAL MODEL IN THE ASSESSMENT OF THE ALGORITHM OF OBJECTS RECORDED BY LASER SCANNING SHAPE DETECTION (ALS/TLS)
PublikacjaBrief description of the study and used methods. Brief description of the study and used As part of the preparatory work aimed to create the application solution allowing for the automation of searching objects in data, obtained in the scanning process using ALS (Airborne Laser Scanning) or TLS (Terrestrial Laser Scanning), the authors prepared a artificial (synthetic, theoretical) model of space, used for the verification of operation...
-
Leadership, culture, intellectual capital and knowledge processes for organizational innovativeness across industries: the case of Poland
PublikacjaPurpose – This study aims to present the overview of intellectual capital creation micro-mechanisms concerning formal and informal knowledge processes. The organizational culture, transformational leadership and innovativeness are also included in the investigation as ascendants and consequences of the focal relation of intellectual capital and knowledge processes. Design/methodology/approach – Based on a sample of 1,418 Polish...
-
Knowledge management strategies in KIBS companies: A preliminary analysis
PublikacjaPurpose – The aim of this paper is to perform a preliminary analysis concerning the detection and examination of two possible opposite approaches to KM planning which will be referred to as deliberate and emergent KM strategies. The goal is to enhance our understanding of the variety of features KM strategies possess and, accordingly, to formulate categorisations that are in line with such characteristics. Design/methodology/approach...
-
Effect of temperature and composition on physical properties of deep eutectic solvents based on 2-(methylamino)ethanol – measurement and prediction
PublikacjaNovel deep eutectic solvents were synthesized using 2-(methylamino)ethanol as hydrogen bond donor with tetrabutylammonium bromide or tetrabutylammonium chloride or tetraethylammonium chloride as hydrogen bond acceptors. Mixtures were prepared at different molar ratios of 1:6, 1:8 and 1:10 salt to alkanolamine and then Fourier Transform Infrared Spectroscopy measurements were performed to confirm hydrogen bonds interactions between...
-
Influence of the position of the swash plate rotation axis on the volumetric efficiency of the axial pistons pumps
PublikacjaThe article describes the influence of the position of the swash plate axis of rotation on the size of the dead space and the volumetric efficiency of the axial pistons pump. Superposition of the two motions have been proposed - the rotation of the swash plate with respect to axis intersecting the axis of rotation of the pump shaft and the shifts of swash plate yielding a result of the rotation axis offset effect. In the article...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublikacjaAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublikacjaThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...
-
Influence of excitons interaction with charge carriers on photovoltaic parameters in organic solar cells
PublikacjaWe report on theoretical analysis of excitons annihilation on charge carriers in organic solar cells. Numerical calculations based on transient one-dimensional drift-diffusion model have been carried out. An impact of three quantities (an annihilation rate constant, an exciton mobility and a recombination reduction factor) on current density and concentrations of charge carriers and excitons is investigated. Finally, we discuss...
-
Influence of a Radio Frequency on RF Fingerprinting Accuracy Based on Ray Tracing Simulation
PublikacjaIn this paper the influence of a radio signal frequency on performance of Indoor Positioning System based on fingerprinting has been examined using ray-tracing simulations. It has been simulated how spatial distribution of an RF signal strength change with the signal’s frequency. The results were used to show its’ impact on the behavior of localization algorithms that are employing RSS measurements to determine node’s position...
-
The influence of accumulation area and the length of pedestrian route on functioning of roundabouts with traffic signals
Publikacjatraffic volumes. This kind of intersection is commonly used in the centres of Polish cities on multilane roads and fairly common in the case of tram lines running through a central island. The increase of traffic flow volumes on left turn and U-turn has made this type of roundabout difficult to operate. Small storage areas around central islands are critical places that significantly influence the capacity of this kind of intersection....
-
Assessment of User Mobility’s Influence on System Loss in Several Body-to-Body Scenarios
PublikacjaIn this paper, Body-to-Body communications in indoor and outdoor environments for different on-body antenna configurations and different mobility scenarios were studied, based on system loss measurements at 2.45 GHz. The main objective is to properly characterise the influence of the Transmitter-Receiver configuration on system loss and fast fading behaviour, the latter being modelled by the Rice Distribution. Globally, it is observed...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublikacjaThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
Influence of finishing colour on the efficiency of automated production line for wooden doors
PublikacjaPorta KMI Poland S.A. company has implemented a fully automated intelligent technological line TechnoPORTA for customized mass-production of technical door leaves. Each door leaf is provided with a unique QR code. It allows the line modules to individually adjust the machining parameters to the currently processed element according to the IT controlling system. Before en-tering the TechnoPorta line, the door leaves are not sorted,...
-
Application of Monte-Carlo method to modelling influence of selected soil heterogeneity on macrodispersion of pollutants in unsaturated soil medium
PublikacjaThe influence of soil heterogeneity on miscible solute transport in soil is analyzed. The transport process is simulated numerically using the Monte-Carlo method. This paper shows how different types of soil heterogeneity influence the process of contaminant spreading. If independent flow paths exist in the soil, the degree of the mixing of pollutants in the outflow from the soil profile is larger. If the preferential flow paths...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Mercury concentration in the sediments as a function of changing climate in coastal zone of Southern Baltic Sea – preliminary results
Publikacja -
Assessment of the Global and Regional Land Hydrosphere and Its Impact on the Balance of the Geophysical Excitation Function of Polar Motion
Publikacja -
A Potential Relationship Between Estrogen Receptors Polymorphisms, Sperm Function and in vitro Fertilization Success: A Preliminary Study*
Publikacja -
The molecular function of kallikrein‐related peptidase 14 demonstrates a key modulatory role in advanced prostate cancer
Publikacja -
Mercury concentration in the sediments as a function of changing climate in coastal zone of Southern Baltic Sea – preliminary results
PublikacjaMercury, despite of its many uses in industry, is also highly toxic. It is highly neurotoxic, and because of the ability of mercury to penetrate placental barrier, in some countries ban on predatory fish consumption (the main route of mercury into human organism) by pregnant women was introduced. There are very little publications describing the consequences of weather anomalies on contaminants cycles. No research was published...
-
Inverse method for 2D viscous flow design problem using stream-function coordinates for axisymmetric model
PublikacjaOpracowano metodę odwrotną dla przepływów lepkich nieściśliwych w osiowosymetrycznej konfiguracji. Użyto współrzędnych funkcji prądu mających tą właściwość, iż możliwe jest zastapienie jednej współrzędnej geometrycznej zmienną zależną od prędkości przepływu. W związku z czym możliwe jest rozwiązanie zadania projektowego. Metodę rozwiązano numerycznie dla przypadku testowego jak i pokazano możliwości metody dla bardziej skomplikowanego...
-
Green`s function methods for Mathematical modeling of unidirectional diffusion process in isothermal metals bonding process
PublikacjaPodano wykorzystanie funkcji Greena w rozwiązaniu matematycznego modelu dyfuzji jednowymiarowej podczas izotermicznego łączenia metali.
-
Site-to-site distance distribution in flexible molecules: theoretical evaluation of the donor and/or acceptor fluorescence decay function
PublikacjaPrzedstawiono wyrażenie teoretyczne opisujące zależność funkcji zaniku fluorescencji od rozkładu odległości P(r) pomiędzy donorami i akceptorami w giętkich molekułach dwuchromoforowych. Wyrażenie uwzględnia wiekoeksponencjalny zanik izolowanych donorów i akceptorów, a także możliwość niekompletnego oznakowania molekuł akceptorami. Przyjęto, że względne zmiany odległości donorów i akceptorów w czasie życia fluorescencji donora mogą...
-
Winding function approach based design of novel five-phase brushless doubly fed induction generator
PublikacjaThe paper presents the concept of the new design of the five-phase brushless doubly fed induction generator. The generator is dedicated to the modern wind turbine. The innovative design approach uses a five-phase power supply from the stator control winding side of the generator with a stator three-phase classic power winding. The research results presented indicate that the electromagnetic coupling between the control and power...
-
THE MELT FLOWABILITY AND TENSILE PERFORMANCE OF POLY (-CAPROLACTONE)/BREWERS’ SPENT GRAIN COMPOSITES AS A FUNCTION OF FILLER MODIFICATION
PublikacjaNowadays, it is essential to reduce the environmental impact of products and technologies. Such an approach should be highlighted in all research activities. In the case of polymer composites, it can be realized by introducing by-products or waste materials as fillers. An auspicious example of such material is the brewers’ spent grain, the major byproduct of the beer production. Its chemical composition, relatively similar to conventional...
-
P1471Multimodality imaging of left ventricular function and volumes in patients with acute and chronic myocardial injury - Novel insights
Publikacja -
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublikacjaIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
The influence of the thickness, recombination and space charge on the loss of photocurrent in organic semiconductors: an analytical model
PublikacjaWe propose an analytical model of the photocurrent efficiency dependence on the light intensity in organic semiconductors. The influence of the thickness of sample, space charge effects and recombination of charge on the loss of photocurrent has been considered. We demonstrate that the presented model is the enhancement of an analytical model reported recently by Rappaport et al (2005 J. Appl. Phys. 98 033714). The method to identify...
-
The influence of vocational orientation on regional competitiveness
Publikacja -
Influence of the Working Strategy on A-Team Performance
Publikacja -
Influence of boundary conditions in calibration chamber
PublikacjaPrzedstawiono wyniki badań modelowych penetracji w komorze kalibracyjnej z zastosowaniem modeli o różnej średnicy. Badania przeprowadzono w piasku średnio zagęszczonym i zagęszczonym przy stałej składowej poziomej naprężenia i przy składowej pionowej naprężenia w gruncie do 400 kPa. Określono wpływ warunków brzegowych na uzyskane wyniki oporu podstawy/oporu stożka lub ostrza dylatometru. Wyznaczono współczynniki korekcyjne oraz...
-
The influence of antibiotics on the anammox process — a review
Publikacja -
Influence of sulphanilamide in wastewater on Anammox process
PublikacjaBadano wpływ krótko- oraz długookresowej ekspozycji mieszanej kultury Anammox na działanie sulfonamidu. Otrzymane wyniki potwierdziły, że sulfanilamid (SA)hamuje proces Anammox. Wyższe stężenia SA powodowały silniejszy efekt inhibicji usuwania związków azotu ze ścieków. Natomiast długookresowe testy potwierdziły hipotezę, że wydłużenie czasu ekspozycji mikroorganizmów Anammox na działanie SA skutkuje obniżeniem stopnia inhibicji...
-
The influence of magnetic core on frequency characteristics
Publikacja -
The influence of SVC on the progress of voltage collapse
PublikacjaThe article presents the simulation concerning the cooperation of SVC circuit with a generative set in time, when of power system reaches low values which may lead to the fall-out of generator from the synchronous operation.
-
Influence of Exception Handling on Distributed Applications.
PublikacjaW artykule przedstawiono metodologię oceny systemów rozproszonych w sytuacji występowania wyjątków i błędów. Analiza jest przeprowadzana przez zidentyfikowanie zmian stanów danych i wyprowadzenie ogólnych charakterystyk systemu. Rozproszone zależności są modelowane przez podstawowe zależności między metodami i złożone zależności występujące w sytemie. Analiza umożliwia odpowiedź na pytanie, jak zależności rozproszone wpływają na...