Filtry
wszystkich: 1362
wybranych: 1150
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL DEFORMED BAR
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
The Application of Cluster Analysis in the Assessment of the Weldability of Unalloyed Steels
PublikacjaNon-alloy steels constitute a large group of steels characterised by diversified chemical composition, structural morphology and a wide range of mechanical properties (determining weldability). The paper presents results of multidimensional analyses (based on cluster analysis) of 110 selected unalloyed steel grades. Properties adopted as diagnostic features included the chemical composition, mechanical properties (yield point)...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublikacjaThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublikacjaThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Influence of the Widespread Use of Corten Plate on the Acoustics of the European Solidarity Centre Building in Gdansk
PublikacjaThis paper describes the relationship between a strong architectural vision that is difficult to balance, and user expectations in terms of acoustics. The focus is on the use of corten steel as the dominant finishing material on façades and interiors to achieve an expressive, symbolic message through program-based design. The architectural premises justifying the adopted solutions are presented, especially the universality and...
-
Ocena stanu technicznego rurociągu przesyłowego zawiesiny popiołów w Elektrowni Ostrołęka B
PublikacjaPrzedmiotem pracy był rurociąg przesyłowy zawiesiny popiołów przesyłanych z Elektrowni Ostrołęka B. Celem pracy było potwierdzenie przynależności próbek yvyciętych z rurociągu do określonego gatunku stali i ocena stanu materiału po eksploatacji. Dla zrealizowania tego celu wykonano: - analizę składu chemicznego materiału pobranego ze stalowych rur, - mikroanalizę warstw wierzchnich na powierzchni wewnętrznej i zewnętrznej, -...
-
Carbon dioxide sequestration by industrial wastes through mineral carbonation: Current status and perspectives
PublikacjaMineral carbonation using natural minerals or industrial wastes is a safe and promising strategy for CO2 sequestration. Application of industrial wastes for this purpose has significant ecological and environmental value, which is one of the key green technologies in the global carbon mitigation. This review summarizes the current research status of CO2 mineralization by industrial wastes. This work surveys the mechanisms and capacities...
-
Badania nośności na zginanie innowacyjnego kształtownika giętego na zimno typu GEB
PublikacjaLekkie konstrukcje metalowe wytwarzane z kształtowników giętych na zimno to jedna z najszybciej rozwijających się dyscyplin w zakresie budownictwa. Do niedawna profile gięte na zimno stosowano wyłącznie jako elementy drugorzędne, czyli płatwie oraz rygle. Nowo opatentowany przekrój typu GEB ma być wykorzystywany jako element nośny konstrukcji ramowych. Jednak jego zaistnienie na rynku budowlanych konstrukcji metalowych jest uwarunkowane...
-
The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels
PublikacjaIn this study, the fractal dimension of fatigue fracture surfaces is investigated in order to find an alternative failure loading indicator. Some of many metrological factors are generalized by reducing the fracture surface structure to one factor and develop an entire fracture surface procedure by analyzing the impact of surface slope and calculation resolution. Three notched geometries are studied under cyclic bending-torsion:...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Three-dimensional characterization of porosity in iron ore pellets: A comprehensive study
PublikacjaThis paper presents a comprehensive study on the production and reduction of high-quality iron ore pellets characterized by a basicity index nearing 0.5 and diameters ranging from 1 to 2 cm. The reduction process was carried out in a hydrogen atmosphere at temperatures spanning 800–1000 ◦ C and a pressure of 8 bar. Initial f indings revealed substantial variations in pellet density and compressive strength, attributed to their...
-
Energetics of formation and stability in high pressure steam of barium lanthanide cobaltite double perovskites
PublikacjaThis study concerns energetics of formation and the stability in high water partial pressure of BaLnCo2O6−δ, (Ln = La, Pr, Nd, and Gd) (BLnC) and BaGd1−xLaxCo2O6−δ, where x = 0.2, 0.5, and 0.7 (BGLC) double perovskite cobaltites. Those materials are extensively studied due to their potential applications as a positrode in electrochemical devices. Therefore, their stability under such conditions is a key issue. All investigated...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Evaluation of reformer tubes degradation after long term operation
PublikacjaPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublikacjaThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublikacjaDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Polygons vs. clumps of discs: A numerical study of the influence of grain shape on the mechanical behaviour of granular materials
PublikacjaWe performed a series of numerical vertical compression tests on assemblies 01 20 granular material using a Discrete Element code and studied the results with regard to the grain shape. The samples consist of 5000 grains made from either 3 overlapping discs (clumps - grains with concavities) or six-edged polygons (convex grains). These two grain type have similar external envelope, which is a fund ion of a geometrical parameter...
-
Chemical Theory of Machines, basic principles of strength with examples of calculations
PublikacjaThis book encompasses the essential range of information on technical aspects of mechanical design. It was written primarily for the students and staff of chemistry faculties of technical universities, yet it may also be utilized by everyone, who ether would like to try or already enjoys designing, but cannot take advantage of typical stress & machine construction handbooks. These handbooks often require familiarity with the concepts...
-
(R,R)-1-Acetyl-1'-(2,4,6-trinitrophenyl)-2,2'-bipyrrolidine
Publikacja(R,R)-1-Acetyl-1'-(2,4,6-trinitrophenyl)-2,2'-bipyrrolidine has been synthesized and its rentgenostructure has been determined. The structure of the title molecule, C16H19N5O7, is mainly determined by the steric effect of a bulky 2,4,6-trinitrophenyl group attached to the N atom of a pyrrolidine ring. Both pyrrolidine rings adopt an envelope conformation, with one of the methylene C atoms as the flap in each case, and the N-C-C-N...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Storing Matter’technique in SIMS depth profile analysis
PublikacjaSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publikacjaresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Dissimilar underwater wet welding of HSLA steels
PublikacjaThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublikacjaMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Report no: WOiO /II/46/2015 - Construction node verification test, estimation of breaking load (shear force) and destruction form
PublikacjaA new generation of tanks for LNG transportation has been designed. Mass reduction forced our customer to use three different materials: austenitic steel, aluminium alloy and LNG compressed wood between them. The expertise concerns structural node between tank foundation and suspension. Expertise contains: description of object of test, test principals, results and conclusions
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublikacjaThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
Context of Digitalized Employment for Older Adults with Autism Spectrum Disorder in the New Normal
PublikacjaEmployers are actively considering how to normalize remote work technology across different industries. The residual risk of coronavirus disease-19 (COVID-19) will necessarily lower the bar for allowing some workers to stay remote on a more permanent basis. This is based on the realization that many essential jobs can be teleworked while retaining or enhancing productivity. The decisions employers make regarding future work arrangements...
-
Application of g-C3N4/ZnO nanocomposites for fabrication of anti-fouling polymer membranes with dye and protein rejection superiority
PublikacjaPolysulfone (PSf) membranes are privileged for water and wastewater treatment, but because of their hydrophobic nature, they suffer from fouling, which lowers their performance and lifetime. In this work, g-C3N4 and g-C3N4/ZnO nanomaterials were synthesized via a hydrothermal method to modify the PSf membrane for effective dye separation and reduction of organic fouling. Since g-C3N4/ZnO possesses –OH and –NH reactive groups, g-C3N4/ZnO/PSf...
-
Wpływ rodzaju zanieczyszczenia powierzchni odlewu ze staliwa LH14 na jakość napoin wykonanych elektrodą otuloną
PublikacjaNapawanie jest szeroko stosowaną metodą naprawiania powierzchni. Pozwala między innymi na uzupełnienie miejsc, w których uprzednio wystąpiły wżery korozyjne. Techniki napawania wykorzystywane są również do przywracania pierwotnego kształtu zużytych części. W pracy wykonano badania napoin wykonanych elektrodami otulonymi na czołowych powierzchniach cylindrycznych próbek ze staliwa LH14. Proces wykonywano dwoma rodzajami elektrod:...
-
Analisys of the failure of fixator used in bone surgery
PublikacjaThe Gamma nail (fixator) made of stainless steel, which has broken in the body, was subjected to examination. The fixator was removed from the patient femur. The fracture occurred in the area of the nail hole after two months' stay in the organism. The research included chemical composition, hardness of the Gamma nail material and the observation and analysis of the type of fracture. The research showed the fatigue failure of the...
-
Evaluation of cathode materials for electrochemical photocatalyst deposition
PublikacjaElectrochemical deposition of photocatalyst, especially TiO2, onto several cathode materials was investigated and evaluated. The deposited films were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX) and electrochemical measurements. Photocatalytic activity was determined by the decomposition of cyclohexane in air by irradiation with ultraviolet light emitting diodes. It was found that...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublikacjaThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublikacjaIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublikacjaThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
RESEARCH ON ORGANIC COATINGS DESIGNED FOR UNDERWATER APPLICATIONS
PublikacjaUnderwater steel structures require periodic maintenance. In the case of vessels, anti-corrosion works are carried out in the shipyard, where very good conditions for applying organic protective coatings can be provided. Very good surface preparation can be obtained by the use of abrasive blasting. The well-prepared metal surface is free from impurities (particularly inorganic salts). Suitable conditions for the application and...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublikacjaMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
-
Sundials of St Mary’s Church in Gdańsk / Zegary słoneczne kościoła pw. Wniebowzięcia Najświętszej Panny Marii w Gdańsku
PublikacjaThe paper presents contemporary research evidence of form, function and history of the sundials of St Mary’s Church in Gdańsk. The discussed sundials are located on the southern wall of the church transept. The sundial, which is believed to be made by Lorenzo Zachau in 1533, is placed on the west side of the western window, at the edge of the wall. The face of this sundial is separated by a horizontal line into two parts. The upper...
-
Infographics in Educational Settings: A Literature Review
PublikacjaInfographics are visual representations of data that utilize various graphic elements, including pie charts, bar graphs, line graphs, and histograms. Educators and designers can maximize the potential of infographics as powerful educational tools by carefully addressing challenges and capitalizing on emerging technologies. However, current education systems showcase the need for development guidelines and the best practices targeted...
-
Trwałość spawanych instalacji wodnych wykonanych z nierdzewnych stali austenitycznych
PublikacjaW artykule przedstawiono dwa przypadki przedwczesnych uszkodzeń spawanych instalacji wodnych wykonanych ze stali odpornych na korozję. W celu ustalenia przyczyn uszkodzenia instalacji przeprowadzono badania metalograficzne, makro - i mikroskopowe oraz mikroanalizę składu chemicznego EDS na próbkach pobranych z reprezentatywnych miejsc. Wykazano, że głównymi przyczynami awarii rurociągów wody pitnej były niezgodności spawalnicze,...
-
The Characteristic of Surface Layers on Austenitic Stainless SteelAfter Glow-discharge Nitriding Process.
PublikacjaThis paper presents investigation of surface layers. The diffusion layers were produced by using different parameters of reactive atmosphere (N2:H2). The research of the surface layers was performed using scanning electron microscope (SEM). The results of energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD) analysis are presented. Research reveals the influence of chemical constitution of reactive atmosphere on the...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Effect of water salinity on properties of multipass underwater wet manual metal arc welded joints
PublikacjaThe weldability of steel under the water is limited due to the influence of the environment. Water causes limited visibility, presence of the residual stresses, increasing the cooling rate, and increasing the diffusible hydrogen content in deposited metal, leading to the formation of brittle microstructures in heat-affected zone (HAZ). The paper presents the results of mechanical properties testing of S420G2+M steel welded joints...
-
Morphology changes in Fe-Cr porous alloys upon high-temperature oxidation quantified by X-ray tomographic microscopy
PublikacjaThe effect of high-temperature oxidation at 850 C (10 h, 30 h, 100 h) and 900 C (10 h) on porous (30 % porosity) ferritic stainless steel (Fe22Cr) has been investigated using synchrotron tomographic microscopy, which allowed for visualisation, separation and quantitative analysis of the metallic core, closed pores, open pores and oxide scale phase. The same regions within the samples were investigated before and after oxidation...