Wyszukiwarka
Filtry
wszystkich: 177
wybranych: 166
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: LOAD CAPACITY
-
Influence of nodes with positive eccentricity on load-carrying capasity of truss' top chords in trusses made of welded cold-formed members.
PublikacjaIn order to establish the influence of eccentric crossing of truss members on the load-carrying capacity of the folded chord of a hat-section truss, a research model was created and preliminary numerical analysis of the truss was performed with the use of Marc Mentat programme. Distorial instability of crossheads caused by deviation of loose (unmounted) channel section web’s bends was observed. Due to the slenderness of the section’s...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublikacjaThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Discrete random variables in reliability calculations of a reticulated shell
PublikacjaImplementation of the Point Estimation Method (PEM) in the reliability analysis of a three-dimensional truss structure is presented in the paper. The influence of geometric and material random parameters on the truss load-carrying capacity was investigated. The analysis was performed for different combinations of basic variables. Symmetric and asymmetric cases of snow load were taken to assess the structural reliability. Sensitivity...
-
Prototype design and development of low-load-roof photovoltaic modules for applications in on-grid systems
PublikacjaFour prototypes of lightweight photovoltaic modules for applications in on-grid systems have been designed, developed, manufactured and tested for compliance with relevant IEC standards. Selected, commercially available materials characterized by thermogravimetry, differential scanning calorimetry, dilatometry, scanning electron microscopy and nanoindentation technique were used in frameless, adhesively-bonded sandwich-structures...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu „Geb“
PublikacjaOne of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight, so manufacturers are increasingly using the possibilities of those sections for the production of typical single-storey steel structures systems. Well known profiles, such as Z, C and the so called hat sections that have been studied and described in the literature, are used mainly as purlins or truss components....
-
Innovative cold-formed GEB section under compression
PublikacjaCold-formed steel sections extensively affect the modern steel construction industry. Not only are they used as secondary elements like purlins or sheeting, but also they can serve as primary load-bearing members in fabricated steel panels and trusses. A new cross-section called shortly a GEB may serve as that member. However, its existence of the metal building structures industry depends on the exact, optimal dimensional parameters...
-
Badania eksperymentalne słupów CFST z betonem zwykłym i ekspansywnym
PublikacjaPraca przedstawia badania eksperymentalne ponad 40 słupów CFST. Analizie poddano wyniki siły niszczącej słupy w aspekcie grubości stalowego płaszcza, smukłości słupa, rodzaju betonu wypełniającego stalową rurę (zwykły i ekspansywny) i jego wytrzymałości a także sposobu obciążania słupa (przez rdzeń lub przez cały przekrój). Sprawdzono efektywność słupów CFST z użyciem betonu ekspansywnego i zwykłego rozumianą jako stosunek nośności...
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publikacjahis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Ocena pracy dźwigara zadaszenia Hali Blanika w Gdańsku
PublikacjaWartykule przedstawiono kompleksowe sprawdzenie nośności stalowej konstrukcji zadaszenia Hali Leszka Blanika w Gdańsku. Dokonano oceny wpływu otworów dużej średnicy w środnikach dźwigara na jego nośność. Oszacowano nośność nietypowego, zginanego styku doczołowego łączącego elementy dwuteowe klasy 4. Obliczenia wykonano na podstawie norm i analiz modeli MES.
-
Concrete-filled FRP tubular members in marine and bridge structures
PublikacjaConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublikacjaLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublikacjaIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublikacjaPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublikacjaHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
Application and mechanical properties of aluminium alloys
PublikacjaThe paper presents a short survey of the application and mechanical properties of aluminium alloys. This area of scientific research is still developing, the authors restricted it to about 30 papers. Numerical simulations of the aluminium bracket are also investigated. The authors propose a solution to increase the load capacity of aluminium brackets with application of the additional cover plates. This study is proposed as an...
-
Zagrożenie katastrofą budowlaną Mostu Uniwersyteckiego w Bydgoszczy. Analiza i badania
PublikacjaMost Uniwersytecki został zamknięty po 7 latach od oddania do użytku. Powodem były błędy projektowe ujawnione w przeglądzie w roku 2020, potwierdzone teoretycznymi analizami nośności. Bezpośrednim powodem zamknięcia przeprawy było stwierdzenie zagrożenia katastrofą budowlaną. W roku 2021, zgodnie z zaleceniem i koncepcją ekspercką, krytyczne elementy konstrukcji mostu zostały wzmocnione. W styczniu 2022 most został przywrócony...
-
Report of Eurocode 7 application for pile foundation design in Poland
PublikacjaThe EC7 rules of geotechnical design are in use in Poland for several years, even though there is no National annex. With regard to pile foundations, there are valid EC7 recommendations concerning design approaches, load partial coefficients, correlation coefficients and capacity partial coefficients. Polish designers can be quite flexible when it comes to choose a method for static, bearing capacity and settlement calculations....
-
Numerical and Analytical Investigation of Aluminium Bracket Strengthening
PublikacjaThis paper focuses on an analytical and numerical investigation of aluminium brackets used to fasten light-weight curtain walls to building facilities. The authors propose a solution to increase the load capacity of aluminium brackets by means of additional cover plates (straps). This paper also includes a short survey of literature and material properties concerning the EN AW-6060 T6 aluminium alloy. This paper suggests an initiation...
-
THE APPLICATION OF PHENOMENOLOGICAL METHODOLOGY FOR DESIGNING PILE FOUNDATION IN PORT STRUCTURES
PublikacjaIt is of utmost importance in the design process that a suitable, safe and concurrently economic solution be chosen. Issues connected with foundations require adopting a special approach. Soil is a composite medium, and it is essential to describe as precisely as possible the interaction taking place between the subgrade and the structure. There are many design methods of pile foundation that are based on in-situ test of soils....
-
The impact of material degradation on the resistance and reliability of truss structures
PublikacjaThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Experimental tests of steel double-type balcony connections
PublikacjaThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
ECONOMICAL AND SAFE METHOD OF GRANULAR MATERIAL STORAGE IN SILOS IN OFFSHORE PORT TERMINALS
PublikacjaThe article discusses issues related with storage of granular materials in silos made of corrugated sheets and reinforced with vertical ribs. Advantages and disadvantages of these structures are named, and typical technological solutions used by largest silo producers are presented. Moreover, basic assumptions of Eurocode 3 are discussed in the context of determining the buckling load capacity of a ribbed jacket. Alternative methods...
-
Optimizing the parameters of a small standalone hybrid power system
PublikacjaA hybrid power plant consists of renewable energy resources, an energy storage, a discharge load and an emergency power supply. Power plant parameters are tailored to meet the requirements of continuity of supply, cost minimization, return on investment period and system capacity utilization. The papaer presents the methodology for selecting power plant parameters with a larger number of decision criteria. The task is solved...
-
A concept of zero-dimensional and three-dimensional thermodynamic modelling of steam storage in a steam cycle
PublikacjaThis work presents the thermodynamic model of steam storage in a steam cycle. The innovative steam storage is an integral part of the unit and thus responds quickly to changes in load. This enhances the primary control reserve while maintaining high efficiency of energy conversion. With regard to power plants, it improves the operational safety of generation units, as it prevents boiler and turbines overload in the case of steep...
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublikacjaThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublikacjaCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Increasing the lifetime of engineering structures through the use of composite laggings
PublikacjaThe use of composite laggings prevents concrete (chemical and biological) corrosion. Columns coated with composite or reinforced composite are more resistant to negative environmental impact on concrete or steel. The mechanical properties of the reinforced casing also cause that these types of columns are more resistant to lateral forces. The applied casing limits carbonization of concrete and cyclical freezing and thawing with...
-
The validation process of truss model with joint eccentricities
PublikacjaNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublikacjaWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Investigation and operation problems of metal tanks in Poland
PublikacjaThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublikacjaThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
-
Search for the most useful geometry of an acoustic journal bearing
PublikacjaComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Wpływ ukształtowania zbrojenia na zarysowanie i nośność żelbetowego węzła tarczowego ze wspornikiem
PublikacjaPraca ma charakter eksperymentalno-teoretyczny i dotyczy zagadnień związanych z żelbetowymi tarczami pracującymi w przestrzennym układzie konstrukcji budynków. Celem niniejszej dysertacji było określenie wpływu głównych parametrów jakimi są sposób ukształtowania zbrojenia i smukłość ścinania na zarysowanie i nośność żelbetowego przestrzennego węzła tarczowego ze wspornikiem. Na podstawie aktualnego stanu wiedzy, opracowano program...
-
Zmodernizowany most Łazienkowski w Warszawie – analizy z wykorzystaniem modelu numerycznego MES
PublikacjaW artykule przedstawiono proces modelowania statycznego przęseł mostu Łazienkowskiego w Warszawie, który został poddany odbudowie po pożarze 14 lutego 2015 r. Sprawdzające obliczenia numeryczne wykonano w związku z badaniami konstrukcji podczas próbnego obciążenia. Przeprowadzono weryfikację obliczeń projektowych i zaprojektowano próbne obciążenie. Podsumowano wyniki analizy i badań. Dodatkowo opisano nową, stalową konstrukcję...
-
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublikacjaThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublikacjaThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
Shaft friction from the DMT and direct shear interface tests
PublikacjaThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Modeling of truss with cold-formed section and positive eccentricity in the node
PublikacjaThis work is dedicated to establishing the load carrying capacity of tensed and compressed truss’ nodes made of cold-formed open cross sections. The occurrence of bending in the truss’ nodes is the result of a specific production technology for system lattice girders assumed by the designer and the producer. The aim of this research is to present the methodology of conduct for creation of computational models that best depict the...
-
Higher harmonics produced by traction substations – computer modelling and experimental verification
PublikacjaVoltage and current harmonics have a detrimental effect on the components of a power system. Current harmonics may result in the overload and damage to power transformers, although the rms value of load current does not exceed their current-carrying capacity. Voltage harmonics may result in, for example, damage to capacitor banks used to compensate reactive power. Devices which contribute to both current and voltage distortion...
-
Normal stress distribution in built‑up cold‑formed column in relation to interconnecting bolt spacing
PublikacjaIn order to increase a stiffness of cold-formed steel (CFS) elements it is practised to built-up the cross-section. In the analysed case, a main element is strengthened by adding extra chord in contact partially along the column. This additional chord acts as a longitudinal stiffener connected with the main section by series of bolts. Authors check whether rules applied over the years, for hot-rolled elements, can be indiscriminately...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublikacjaIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Experimental study of the post tensioned prestressed concrete corbels
PublikacjaThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Intelligent microbearing project with memory of stress-strain history
PublikacjaTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Numerical Modelling of Connections Between Stones in Foundations of Historical Buildings
PublikacjaThe aim of this paper is to analyse the behaviour of old building foundations composed of stones (the main load-bearing elements) and mortar, based on numerical analysis. Some basic aspects of historical foundations are briefly discussed, with an emphasis on their development, techniques, and material. The behaviour of a foundation subjected to the loads transmitted from the upper parts of the structure is described...
-
Reliability assessment of an OVH HV power line truss transmission tower subjected to seismic loading
PublikacjaThe study focuses on the reliability of a transmission tower OS24 ON150 + 10, an element of an OVH HV power line, under seismic loading. In order to describe the seismic force, the real-life recording of the horizontal component of the El Centro earthquake was adopted. The amplitude and the period of this excitation are assumed random, their variation is described by Weibull distribution. The possible space state of the phenomenon...
-
Towards Understanding of Mechanics of Hernia Managed by Synthetic Mesh in Laparoscopic Operation: A Single Case Study
PublikacjaIn this paper a research towards understanding of mechanics of ventral hernia operated with the use of Physiomesh Open image in new window implant and SecureStrap Open image in new window staples is described. Experimental and numerical studies are conducted for that purpose. Experimental works cover uni-axial tension tests of the implant samples and of the implant-staples-tissue system. Also experiments on implant-staples-tissue...
-
Basic sensitivity analysis of a telecommunication tower complementing standard reinforcement design process
PublikacjaThis paper presents straightforward sensitivity assessment of a telecommunication tower. The analysis is set toidentify the elements of the tower which may be reinforced with the greatest structural advantage. As current expertopin ions on structural redesign of similar structures due to a planned addition of extra loads are mainly based ondeterministic computations or engineering intuition,...