Filtry
wszystkich: 672
wybranych: 643
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: TEMPERATURE CONTROL
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublikacjaThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublikacjaThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Influence of electropolymerization temperature on corrosion, morphological and electrical properties of PPy doped with salicylate on iron
PublikacjaIn this work, the influence of the electropolymerization temperature on corrosion, morphological and electrical properties of polypyrrole (PPy) film is studied. Polypyrrole is electrochemically synthesized on iron in the presence of sodium salicylate. The X-ray diffraction and scanning electron microscopy are performed in order to study the structure and morphology of electrodeposited PPy. The electroactive surface area, corrosion...
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublikacjaThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublikacjaZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
High temperature air/steam gasification of biomass in view of hydrogen rich gas production.
PublikacjaArtykuł przedstawia opis nowej i zaawansowanej metody konwersji termochemicznej biomasy i miejskich odpadów stałych w paliwo gazowe, bogate w wodór. W porównaniu z tradycyjnym procesem gazyfikacji, w metodzie tej wykorzystuje się powietrze/parę wodną przegrzane do wysokiej temperatury (powyżej 1300 st. C). Przegrzanie powietrza lub pary wodnej odbywa się z zastosowaniem ceramicznego przegrzewacza wysokotemperaturowego. W celu...
-
Hydrogen rich gas production from high temperature air/steam gasification of biomass
PublikacjaW pracy przedstawiono nowoczesną technikę konwersji biomasy oraz stałych odpadów komunalnych w celu produkcji paliwa gazowego bogatego w wodór. Opisany proces gazyfikacji przebiega w wysokiej temperaturze przy obniżonej koncentracji tlenu i udziale pary wodnej. Dzięki temu możliwa jest produkcja gazów palnych, w szczególności H2, który można wykorzystać do produkcji energii elektrycznej i cieplnej.
-
(Vapour and liquid) equilibrium in (N,N-dimethylacetamide+methanol+water) at the temperature 313.15 K.
PublikacjaPraca zawiera wyniki pomiarów całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla ''składowych'' układów binarnych. Wyniki obliczeń nadmiarowej energii swobodnej mieszania dla układów (N,N-dimetyloaceta-mid+woda) i (N,N-dimetyloacetamid+metanol) porównane zostały z rezultatami uzyskanymi wcześniej dla innych układów (amid+metanol) oraz (amid+woda). Znaleziono interesującą zależność wartości nadmiaru...
-
An Impact of Environmental Disturbances on Combined Cycle Power Plant Control
PublikacjaCombined cycle power plants operate at thermal efficiency approaching 60 percent. In the same time their performance presents several problems that have to be addressed. E.g. gas turbines are very sensitive to backpressure exerted on them by the heat recovery steam generators as well as to ambient pressure and temperature.
-
Energy-Aware High-Performance Computing: Survey of State-of-the-Art Tools, Techniques, and Environments
PublikacjaThe paper presents state of the art of energy-aware high-performance computing (HPC), in particular identification and classification of approaches by system and device types, optimization metrics, and energy/power control methods. System types include single device, clusters, grids, and clouds while considered device types include CPUs, GPUs, multiprocessor, and hybrid systems. Optimization goals include various combinations of...
-
Successive cytotoxicity control by evolutionary surface decorated electronic push-pull green ZnCr-LDH nanostructures: Drug delivery enlargement for targeted breast cancer chemotherapy
PublikacjaThe reason for the increasing bioavailability and biocompatibility of the porous nanomaterials in the presence of different (bio)molecules is still unknown. The role of difference functional groups and their interactions with the potential bioavailability and biocompatibility is of great importance. To investigate the potential contribution of the electronic effects (especially on the surface of the porous nanomaterials) on their...
-
Problems of Active Dynamic Thermography Measurement Standardization in Medicine
PublikacjaReliability of thermographic diagnostics in medicine is an important practical problem. In the field of static thermography, a great deal of effort has been made to define the conditions for thermographic measurements, which is now the golden standard for such research. In recent years, there are more and more reports on dynamic tests with external stimulation, such as Active Dynamic Thermography, Thermographic Signal Reconstruction...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublikacjaThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Study of pH and temperature effect on lipophilicity of catechol-containing antioxidants by reversed phase liquid chromatography
PublikacjaLipophilicity of selected antioxidant phytochemicals, including flavonoids, phenolic acids and xanthonoids, was determined by reversed phase high performance liquid chromatography with UV detection (RP-HPLC-UV). The analyses run at different temperature and pH conditions in isocratic mode suggested that lipophilicity as distribution coefficient (logD) between aqueous and organic phase decreases with increasing temperature. For...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublikacjaPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
The influence of high temperature wood drying conditions using air-steam mixture on its properties
PublikacjaThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublikacjaThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Dissolution of Nb-doped hydroxyapatite prepared via low-temperature mechanochemical method: Spectroscopy studies
PublikacjaCalcium phosphate glass ceramics with nominal hydroxyapatite stoichiometry doped with niobium were synthesized using simple as well as low-temperature mechanochemical method and then in the form of compressed pellet were submitted to the static dissolution process in distilled water for one month. The results of structural analysis, performed mainly on the base of spectroscopic methods such as: infrared absorption spectroscopy,...
-
Deposition and Electrical and Structural Properties of La0.6Sr0.4CoO3 Thin Films for Application in High-Temperature Electrochemical Cells
PublikacjaLow-temperature deposition of electroceramic thin films allows the construction of new devices and their integration with existing large-scale fabrication methods. Developing a suitable low-cost deposition method is important to further advance the development of microdevices. In this work, we deposited a 1-lm-thick La0.6Sr0.4CoO3d (LSC) perovskite with high electrical conductivity on sapphire substrates at 400C and analyzed its...
-
Effect of Increased Temperature on Native and Alien Nuisance Cyanobacteria from Temperate Lakes: An Experimental Approach
Publikacja -
Tetraalkylammonium acetates and tetraalkylammonium tetrafluoroborates as new templates for room-temperature synthesis of mesoporous silica spheres
Publikacja -
Towards Temperature Dependent Coarse-grained Potential of Side-chain Interactions for Protein Folding Simulations
Publikacja -
Effect of pyrolysis temperature on the microstructure and thermal conductivity of polymer-derived monolithic and porous SiC ceramics
Publikacja -
On the critical temperature discontinuity at the theoretical bcc-fcc phase transition in compressed selenium and tellurium superconductors
Publikacja -
Modeling of the L and M x-ray line structures for tungsten in high-temperature tokamak plasmas
Publikacja -
The Influence of Ambient Temperature Changes on the Indicators of Inflammation and Oxidative Damage in Blood after Submaximal Exercise
Publikacja -
Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych obwodowego rozkłądu temperatury w poziomych rurkach, ogrzewanych elektrycznie na których zachodzi wrzenie pęcherzykowe. Wykazano, że lokalne - w obszarze górnej tworzącej rurki, zastosowanie powłki porowatej prowadzi do wygładzenia rozkładu temperatury oraz obniżenia średniej temperatury ścianki.
-
Effect of previous lowering of skin temperature on the time of safe exposure to a hot environment: a case study
Publikacja -
Odour Emissions of Municipal Waste Biogas Plants—Impact of Technological Factors, Air Temperature and Humidity
Publikacja -
The influence of local temperature and air velocity changes on the thermal sensations of users' working in surgical clothing
Publikacja -
Landsat 8 Data as a Source of High Resolution Sea Surface Temperature Maps in the Baltic Sea
Publikacja -
Spectroscopic properties of high-temperature sintered SrS:0.05%Ce3+ under high hydrostatic pressure
Publikacja -
Aluminide Thermal Barrier Coating for High Temperature Performance of MAR 247 Nickel Based Superalloy
Publikacja -
Long-term Hindcast Simulation of Currents, Sea Level, Water Temperature and Salinity in the Baltic Sea
PublikacjaThis dataset contains the results of numerical modelling of currents, sea level, water temperature and salinity over a period of 50 years (1958–2007) in the Baltic Sea. A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model (PM3D) based on the Princeton Ocean Model (POM). The spatial resolution was 3 nautical miles, i.e. about 5.5 km. Currents, water temperature, and salinity were recorded...
-
The effect of the wood temperature upon specific cutting resistance during machining with narrow-kerf saws
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych właściwego powierzchniowego oporu skrawania drewna sosny w funkcji wilgotności drewna, temperatury drewna oraz prędkości posuwu podczas przecinania cienkimi piłami. Proces cięcia prowadzono na pilarce ramowej wielopiłowej PRW15M. Sosnowe próbki przed badaniami mrożono w komorze klimatycznej - temperatura drewna -5 C deg., -20 C deg., +20 C deg. Czas wymrażania przed próbami określano...
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublikacjaW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
Experimental and mathematical modelling study of gas combustion under the high-temperature and oxygen-deficient oxidizers
PublikacjaPraca przedstawia wyniki badań eksperymentalnych i modelowania numerycznego wpływu parametrów utleniacza za długość i objętość płomienia przy spalaniu paliwa gazowego w środowisku o wysokiej temperaturze i ubogim w tlen.
-
High temperature corrosion of steel equipment in modern rafinery environments with high and low sulphur content
PublikacjaPrzedstawiono charakterystykę i mechanizmy procesów wysokotemperaturowej korozji elementów ze stali we współczesnych rafineriach ropy naftowej podczas eksploatacji we frakcjach węglowodorowych o niskiej i wysokiej zawartości siarki. Zwrócono uwagę na procesy korozji siarkowej w obecności wodoru i bez obecności wodoru oraz proces pylenia metalu pod wpływem węgla ze środowiska - w wypadku niskiej zawartości siarki w środowisku.
-
The isomerization of α-pinene over the Ti-SBA-15 catalyst—the influence of catalyst content and temperature
Publikacja -
Effect of Temperature on n-Tetradecane Emulsion in the Presence of Phospholipid DPPC and Enzyme Lipase or Phospholipase A2
Publikacja -
High Temperature Air/Steam Conversion of Biomass and Wastes Into Fuel Gas for Heat and Electricity Production
PublikacjaPaper present principle of high temperature air/staem gasification as well as some results of research using this technology for conversion of biomass and wastes into fuel gas.
-
Low temperature growth of diamond films on optical fibers using Linear Antenna CVD system
PublikacjaIt is not trivial to achieve a good quality diamond-coated fibre interface due to a large difference in the properties and composition of the diamond films (or use coating even) and the optical fibre material, i.e. fused silica. One of the biggest problems is the high temperature during the deposition which influences the optical fibre or optical fibre sensor structure (e.g. long-period gratings (LPG)). The greatest advantage of...
-
High Temperature Corrosion Evaluation of Porous Hastelloy X Alloy in Air and Humidified Hydrogen Atmospheres
PublikacjaIn this work a commercially available porous Hastelloy X alloy is characterized in terms of high temperature corrosion resistance. The alloy was oxidized in the temperature range from 500C to 900C in air and humidified hydrogen for 100 hours. Corrosion rates and porosity changes were measured. Microstructural characterization was performed using X-ray diffractometry and scanning electron microscopy. Results show that porous alloys...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublikacjaThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublikacjaThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
Room temperature depinning of the charge-density waves in quasi-two-dimensional 1T-TaS2 devices
PublikacjaWe report on the depinning of nearly commensurate charge-density waves in 1T-TaS2 thin films at room temperature. A combination of the differential current–voltage measurements with the low-frequency noise spectroscopy provides unambiguous means for detecting the depinning threshold field in quasi-2D materials. The depinning process in 1T-TaS2 is not accompanied by an observable abrupt increase in electric current—in striking contrast...