Filtry
wszystkich: 179
wybranych: 175
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: SAWDUST, IMPREGNATION OF WOOD, PINE WOOD, SAWING PROCESS, FRAME SAWING MACHINE
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublikacjaIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublikacjaThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Forecasting values of cutting power for the sawing process of impregnated pine wood on band sawing machine
PublikacjaW artykule przedstawiono prognozowane wartości mocy skrawania dla pilarki taśmowej (ST100R firmy STENNER), które są stosowane w polskich tartakach. Wartości mocy skrawania oszacowano dla drewna sosny zwyczajnej (Pinus sylvestris L.), które zostało poddane impregnacji. Dla porównania wyznaczono również wartości mocy skrawania dla drewna niezaimpregnowanego. Wartości te określono za pomocą innowacyjnej metody prognozowania sił skrawania,...
-
Granulometric characterization of Arctic driftwood sawdust from frame sawing process
PublikacjaArctic driftwood can be used as an alternative source of wood as construction timber and furniture material, especially in Iceland and Greenland. The use of Arctic driftwood can help in the fight against climate change, by developing land reforestation processes and reducing the volume harvested wood from forests and sustainability of harvesting processes. In this paper the results of an analysis of the effect of long-term residence...
-
Frame sawing machines for accurate wood re-sawing
PublikacjaPrzedstawiono zwięzłą historię pilarek ramowych. Zaprezentowano ekologiczne i ekonomiczne zalety pilarek ramowych nowej generacji. Opisano podstawowe cechy układów kinematycznych nowoczesnych pilarek ramowych oraz podano ich podstawowe dane techniczne.
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublikacjaIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Sawdust size distribution analysis of thermally modified and unmodified oak wood sawed on the frame sawing machine PRW15-M
PublikacjaW pracy przedstawiono wyniki analizy granulometrycznej składu wiórów drewna dębowego niemodyfikowanego i modyfikowanego termicznie uzyskanych podczas piłowania na pilarce ramowej PRW15-M z prędkością posuwu 1.67 mmin-1. Otrzymane trociny termicznie modyfikowanego drewna dębowego składają się z wiórów o ziarnistości w przedziale od 44.7 mm do 4.6 mm, podczas gdy dla drewna niemodyfikowanego zaobserwowano zmiany ziarnistości w granicach...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublikacjaThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Influence of feed rate on the granularity and homogenity of oak sawdust obtained during the sawing process on the frame sawing machine PRW15M
PublikacjaOpisano wpływ prędkości posuwu na skład granulometryczny i jednorodność trocin dębowych otrzymanych podczas procesu przecinania na pilarce ramowej PRW15M. Wykazano, że otrzymane trociny mogą być wykorzystane w produkcji produktów drewnopochodnych w ilości 75% dla posuwu 0.36 m/min i 82% przy posuwie 1.67 m/min. Pozostałe trociny stanowią odpad.
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublikacjaCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
Economical wood sawing with circular saw blades
PublikacjaMaterial- and energy-saving belong to the basic requirements which are imposed on the contemporary manufacturing processes. Since realization of those processes gives measurable profits not only economical but also ecological. In case of wood sawing with circular saw blades material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence,...
-
The forecasted values of cutting power for sawing on band sawing machines for Polish Scots pine wood (Pinus sylvestris L.) in a function of its provenance.
PublikacjaIn this paper the predicted values of cutting power for band sawing machine (EB 1800, f. EWD), which is used in the Polish sawmills, were showed. The values of cutting power were forecasted for Scots pine (Pinus sylvestris L.) wood of five provenances from Poland. These values were determined using an innovative method of predicting the cutting power, which takes into account of elements of fracture mechanics. The resulting predictions...
-
The preparation method of experimental studies of the wood sawing process
PublikacjaW artykule przedstawiono sposoby działania, mające na celu przygotowanie badań doświadczalnych procesu przecinania drewna sosnowego na małogabarytowej pilarce ramowej PRW15M. Proces przygotowania badań podzielono na kilka etapów: przygotowanie próbek, pomiar własności fizycznych drewna (wilgotności drewna, gęstość drewna), pomiar własności strukturalnych drewna (średniej szerokości przyrostów rocznych oraz średniego udziału drewna...
-
Sawing of wood - mechanics of cutting process, tools and machines.
PublikacjaW pracy przedstawiono wpływ obciażenia piły na dokładnośc przecinania. Zaprezentowano pilarkę ramową z eliptyczną trajektorią ruchu pił i hybrydowym dynamicznie wyrównoważonym napędem ramy piłowej, jak również wizyjny kontroler ostrzy pił tarczowych.
-
An innovative approach to the forecasting of energetic effects while wood sawing
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, the cutting forces (power) problem may be tackled with an innovative, up-to-date fundamental analysis of the mechanics of sawing based on modern fracture...
-
An Innovative Approach to the Forecasting of Energetic Effects While Wood Sawing
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specifi c cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, the cutting forces (power) problem may be tackled with an innovative, up-to-date fundamental analysis of the mechanics of sawing based on modern fracture mechanics....
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublikacjaThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
Lateral forces determine dimensional accuracy of the narrow‑kerf sawing of wood
PublikacjaThe shrinking global forest area limits the supply of industrially usable raw resources. This, in combination with the ever‑increasing consumption of timber due to population growth can lead to the lack of a positive balance between the annual volumetric growth and consumption of wood. An important innovation toward increasing environmental and economic sustainability of timber production is to reduce the volume of wood residues...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Application of Fracture Mechanics for Energetic Effects Predictions While Wood Sawing
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (or power - more interesting from energetic point of view) could be considered from a point of view of modern fracture mechanics. Cutting...
-
Feed forces during cutting of wood on frame sawing machines with narrow-kerf saws.
PublikacjaW pracy przedstawiono wybrane efekty energetyczne procesu przecinania drewna na pilarce ramowej za pomocą cienkich pił. Opisano wyniki badań eksperymentalnych sił posuwu przy zastosowaniu pił o dobrej jakości krawędzi skrawających (piły ostre) oraz pił których krawędzie skrawające były obarczone błędami wykonania w postaci wyszczerbień i wykruszeń krawędzi skrawających. Badania przeprowadzono na pilarce ramowej PRW15M.
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublikacjaSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Sawing of frozen wood with narrow-kerf saws.
PublikacjaPrzedstawiono wyniki badań eksperymantalnych skrawania drewna sosnowego mrożonego na pilarce ramowej PRW15M za pomocą cienkich pił. Badano opory skrawania, chropowatość powierzchni po przecinaniu, dokładność przecinania oraz przeprowadzono analize granulometryczna wiórów. Zaobserwowano wzrost oporów skrawania w raz ze spadkiem temperatury,któremu towarzyszyła również niższa dokładność przeciania w odniesieniu do drewna obrabianego...
-
Chip geometry while sawing frozen wood.
PublikacjaW pracy przedstawiono analizę geometrii wiórów zebranych podczas przecierania pryzm sosnowych o temperaturach -5 st. C, -20 st. C, + 18 st. C na pilarce ramowej przecieranych za pomocą cienkich pił. Analizowano rozkład wiórów w funkcji ich wymiarów podłużnych oraz pola powierzchni. W badaniach wykorzystywano kamere cyfrową, a obrazy z niej uzyskane obrabiano za pomoca oprogramowania opracowanego w srodowisku LabView. W widmach...
-
On some accuracy limiting factors in wood sawing
PublikacjaPrzedstawiono szczegółową klasyfikację czynników determinujących dokładność przecinania drewna piłami. Uwzględniono w niej również pozorną utratę dokładności wynikającą z anatomicznej budowy drewna i metody pomiaru (wykorzystywanie lasera). Występujące błędy przecinania zobrazowano szeregiem przykładów z badań doświadczalnych.
-
CUTTING POWER FORECASTING WHILE WOOD SAWING: FRACTURE MECHANICS APPROACH AND AXELSSON’S MODEL COMPARISON
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Another way is to forecast cutting power consumption on...
-
A newly-developed model for predicting cutting power during wood sawing with circular saw blades
PublikacjaIn the classical approach, cutting forces and cutting power in sawing processes of orthotropic materials such as wood are generally calculated on the basis of the specific cutting resistance kc (cutting force per unit area of cut). For every type of sawing kinematics (frame saws, band saws and circular sawing machines) different empirical values of specific cutting resistance kc have to be applied. It should be emphasised that...
-
Granulometric analysis of dry sawdust from the sawing process on the frame sawing machine PRW15M = Granulometrická analýza suchej piliny z procesu pílenia borovicového dreva na rámovej píle PRW-15M
PublikacjaW artykule przedstawiono wyniki analizy granulometrycznej trocin otrzymanych podczas procesu przecinania drewna sosnowego na pilarce ramowej PRW15M. Wielkość otrzymanych trocin miesciła się w zakresie od 84,7 µm do 15,2 mm. Z punktu widzenia kształtu trociny średniej wielkości d>125µm są swym kształtem zbliżone do włókien drzewnych. Z kolei, drobne frakcje d<125µm mają kształt sześcienny. Ponadto, wzrost prędkości posuwu powoduje...
-
Revisiting The Determination Of Cutting Power While Sawing Of Wood With Circular Saw Blades By Means Of Fracture Mechanics
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Pro-ecological technology of wood sawing with circular saw blades
PublikacjaW niniejszym artykule opisano możliwości materiało- i energooszczędnego przecinania piłami tarczowymi. Przedstawiono również przykłady efektów zastosowania proekologicznych technologii przecinania w przemyśle.
-
Specific cutting resistance while sawing of wood - the size effect
PublikacjaW artykule przedstawiono wyniki analiz zmian właściwego oporu skrawania, przy zastosowaniu współczesnej mechaniki pękania z uwzględnieniem wiązkości. Analizy wykonano dla procesu przecinania drewna na pilarce ramowej PRW15M drewna jesionu i jesionu modyfikowanego termicznie. Zastosowane podejście pozwala na wyjaśnienie zjawiska wzrostu właściwego powierzchniowego oporu skrawania dla niewielkich grubości warstwy skrawanej jako efektu...
-
The original method of cutting power forecasting while wood sawing
PublikacjaEfekty energetyczne procesu przecinania drewna piłami (siły skrawania i moc skrawania) przy klasycznym podejściu do zagadnienia są określane na podstawie wartości właściwego powierzchniowego oporu skrawania. Z drugiej strony siły skrawania można rozważać z punktu widzenia współczesnej mechaniki pękania. Prognozowanie wartości kąta ścinania z zastosowaniem modeli uwzględniających wiązkość materiału obrabianego, ścinanie w płaszczyźnie...
-
On some approaches to cutting power estimation while wood sawing
PublikacjaW niniejszym artykule przedstawiono i porównano metody, które mogą być stosowane do szacowania mocy skrawania przy przecinaniu drewna na pilarkach tarczowych. Przy klasycznym podejściu efekty energetyczne procesu przecinania drewna piłami są obliczane na bazie właściwego powierzchniowego oporu skrawania. W internecie dostępne są narzędzia do określania mocy skrawania w postaci oprogramowania dostępnego on-line, przykładowo "Horsepower...
-
Wood structure constraints on sawing accuracy with narrow-kerf saws
PublikacjaW pracy przedstawiono analizę przyczyn i przykłady niedokładności przecinania wynikających z lokalnych zmian struktury drewna.
-
Dimensional accuracy and roughness of lamellas when sawing frozen wood
PublikacjaPrzedstawiono wpływ obniżania temperatury drewna sosnowego (-5°C i -20°C) i prędkości posuwu na dokładność wymiarową deszczułek oraz chropowatość powierzchni po przecinaniu. Badania prowadzono na pilarce ramowej wielopiłowej PRW15M z użyciem cienkich pił z ostrzami stellitowanymi. Otrzymywane wyniki odnoszono do wyników przecinania drewna o temperaturze +18°C. Profil grubości określano metodą kontaktową z pomiarem ciągłym na długości...
-
The effect of thermal modification of ash wood on granularity and homogeneity of sawdust in the sawing process on a sash gang saw PRW 15-M in view of its technological usefulness
PublikacjaPrzedstawiono wyniki analiz granulometrycznych trocin, drewna jesionowego niemodyfikowanego (Fraxinus exelsior L.) i modyfikowanego termicznie, otrzymanych w procesie przecinania drewna na pilarce ramowej wielopiłowej PRW15-M. Przecinanie drewna prowadzono dla dwu prędkości posuwu 0,36 m·min-1 oraz 1,67 m·min-1. Ziarnistośćpowstających trocin dla drewna jesionowego modyfikowanego termicznie zawierała się w przedziale od 33,5 μm...
-
Sawing frozen wood with narrow kerf saws: Energy and quality effects.
PublikacjaOpór skrawania zależy podczas przecinania nie tylko od wilgotności drewna lecz również od jego temperatury. W pracy przedstawiono wyniki badań eksperymentalnych przecinania drewna sosnowego zmrożonego na pilarce ramowej wielopiłowej. Dla porównania wykonano również testy dla drewna o temperaturze pokojowej. Czynnikami badanymi były: moc skrawania, dokładność przecinania w postaci grubości elementów, a także chropowatość powierzchni....
-
Diagnostic usefulness of granulometric analyses of chips distribution while sawing of wood
PublikacjaW niniejszym artykule opisano drogi transportu wiórów w procesie przecinania drewna i ich wpływ na rozdrobnienie wiórów. Przedstawiono również wyniki badań rozkładu segregacji wiórów powstających w procesie przecinania piłą o powszechnie stosowanej konstrukcji i piłą z domkniętymi rowkami wiórowymi.
-
The prediction method of the shear angle in the cutting zone during wood sawing
PublikacjaW artykule opisano metodę przewidywania kąta ścinania w strefie skrawania dla przypadku przecinania drewna. Kąt ścinania był określany z wykorzystaniem współczesnej mechaniki pękania. Nieliniowe równanie opisujące tą wielkość było rozwiązywane numerycznie za pomocą metody iteracyjnej Newton-Raphson. Otrzymane wyniki obliczeń wykazują możliwość rozszerzenia obszaru modelowania efektów energetycznych procesu przecinania drewna nawet...
-
Optimal selection of the sawdust separation device for a narrow-kerf sawing machine PRW15-M
PublikacjaW pracy przedstawiono granulometryczną analizę rozkładu wiórów i pyłu drzewnego otrzymanego w procesie przecinania suchych pryzm sosnowych na pilarce ramowej wielopiłowej PRW15-M. Wielkości wiórów mieściły się w granicach od 84,7 μm do nawet 14 mm. Te ostatnie są elementami będącymi efektem rozszczepiania dolnej powierzchni pryzmy przez wychodzące z niej ostrza piły. Większośc wiórów z najmniejszych frakcji ma postać sześciennych...
-
Economical wood sawing with circular saw blades of a new design (Ekonomicno piljenje drva kruznom pilom novog dezajna)
PublikacjaMaterial-saving and energy-saving belong to the basic requirements imposed on contemporary manufacturing processes. The realization of these processes gives measurable profi ts, not only economical butalso ecological. In the case of wood sawing with circular saw blades, material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence, it...
-
Fracture mechanics model of cutting power versus widespread regression equations while wood sawing with circular saw blades
PublikacjaA comparison of the theoretical cutting power consumption results forecasted with the model (FM_CM model) which include work of separation (fracture toughness) in addition to plasticity and friction, and two widespread regression equations while wood sawing with circular saw blades has been described. in and cutting power consumption forecasted. In computations of the cutting power consumption during rip sawing of Scots pine wood...
-
Influence of frame sawing machine´s kinematics on saw blade tooth wear.
PublikacjaW pracy przedstawiono wpływ kinematyki pilarki ramowej na zużycie ostrzy piłtrakowych.
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublikacjaThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublikacjaThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...
-
The effect of current signal filtering method on the value of cutting power while sawing wood
PublikacjaThe goal of this work was to investigate an effect of various signal pre-processings on the outline of the electrical power curve and its influence on the measured cutting force estimation. Two signal processing methods were selected for the needs of the experiment, including digital filter and wavelet transform. The filter used was Butterworth, 3rd order band-stop with the cut-out band from 45 Hz to 55 Hz. The second approach...