Filtry
wszystkich: 392
wybranych: 286
Wyniki wyszukiwania dla: web of science
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublikacjaThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
The Life Cycle Assessment and Life Cycle Cost in public works contracts
PublikacjaAn important goal, implemented by EU countries under the Europe 2020 strategy, is sustainable development, which includes supporting economy that effectively uses natural and environmentally friendly resources. Solutions in this area are also promoted in tender proceedings in the area of public procurement. The LCA (Life Cycle Assessment) and LCC (Life Cycle Cost) analysis are indicated as the basis for decision-making by awarding...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublikacjaThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublikacjaThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
Dynamic analysis of temporary steel grandstand equipped with different types of bracing system
PublikacjaIn the paper, behaviour of a temporary steel grandstand equipped with two different types of bracing system has been analysed through the numerical study. A typical solution concerning application of a diagonal tubular members has been compared with elements proposed by authors and called polymer dampers. A polymer element consists of two L-shape steel members bonded with polymer mass. The aim of the paper is to verify the effectiveness...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublikacjaThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Analysis and design improvement of high class roads’ arched sections in Poland
PublikacjaAlthough Polish road network standards, in particular higher classes of roads are improving dynamically the number of fatalities on the network is still higher that EU’s average. Ensuring road safety and high maintaining standards is a complex issue and one that poses a major challenge for all road authorities. Road accidents at high speed roads characterize specially serious material and social consequences, thus research into...
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublikacjaThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Use of radiography images and gray level co-occurrence matrix to investigate gravitational granular flow
PublikacjaThe paper presents analysis of granular gravitational flow based on radiography images processing. The investigations were conducted for silo model geometry with concentric/eccentric discharging modes. The continuous X-ray radiography scans of granular material distribution, acquired during flow, were obtained by means of an especially designed model silo with rectangular bin and different settings of hopper angles. Image processing...
-
Application possibilities of LBN for civil engineering issues
PublikacjaBayesian Networks (BN) are efficient to represent knowledge and for the reasoning in uncertainty. However the classic BN requires manual definition of the network structure by an expert, who also defines the values entered into the conditional probability tables. In practice, it can be time-consuming, hence the article proposes the use of Learning Bayesian Networks (LBN). The aim of the study is not only to present LBN, which can...
-
Influence of selected additives and admixtures on underwater concrete and the environment
PublikacjaThe intensive civilization development has an influence on searching for new possibilities connected with extension of city agglomerations, both the areas of flat building and the industrial areas. One of the most interesting solution is to use water reservoirs, rivers and sea areas. The extension of buildings has an influence on building materials, especially hydrotechnical, which means development of production of hydrotechnical...
-
Application of ANN and PCA to two-phase flow evaluation using radioisotopes
PublikacjaIn the two-phase flow measurements a method involving the absorption of gamma radiation can be applied among others. Analysis of the signals from the scintillation probes can be used to determine the number of flow parameters and to recognize flow structure. Three types of flow regimes as plug, bubble, and transitional plug – bubble flows were considered in this work. The article shows how features of the signals in the time and...
-
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublikacjaThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Improvement of radiotracers experiments in mass transfer processes
PublikacjaThe greatest part of industrial mass transfer is based on continuous transportation of different substances throughout especially constructed installations. In that kind of practice, a flow of such mass in each part determines the process unit and can be described by the residence time distribution (RTD) of the substance inside this unit. This parameter may be evaluated by the properly arranged tracer experiment. It is worthwhile...
-
Graphene field-effect transistor application for flow sensing
PublikacjaMicroflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC) and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublikacjaOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...
-
Growing role of walking and cycling and the associated risks
PublikacjaIncreasing the role of active mobility, including walking and cycling, is one of the tools for developing sustainable urban transport systems as recommended by the EU. The article describes the trends in pedestrian and bicycle traffic in Poland and its share in urban modal split. It identifies and describes the main sources of risks to pedestrian and cycle safety. Recommendations are...
-
Signals features extraction in radioisotope liquid-gas flow measurements using wavelet analysis
PublikacjaKnowledge of the structure of a flow is significant for the proper conduct of a number of industrial processes. In this case, a description of a two-phase flow regimes is possible by use of the time-series analysis in time, frequency and state-space domain. In this article the Discrete Wavelet Transform (DWT) is applied for analysis of signals obtained for water-air flow using gamma ray absorption. The presented method was illustrated...
-
Analysis and interpretation of radiometric signals in a liquid-gas bubble flow
PublikacjaThe article presents the analysis of signals from a radiometric system consisting of two scintillation probes and two gamma radiation sealed sources. Calculations and interpretation were carried out for the bubble flow of the water-air mixture in the horizontal pipeline. The analysis of the obtained signals was done in time and frequency domain. In the frequency domain, a range of usable frequencies was identified, which were associated...
-
The use of various species of fungi in biofiltration of air contaminated with odorous volatile organic compounds
PublikacjaAir pollution with odorous compounds is a significant social and environmental problem. This paper presents biological deodorization methods. The attention is focused on the application of biotrickling filters for air deodorization. Principles of their operation are discussed, indicating the key role of the selection of microorganisms responsible for the degradation of odorous compounds. A literature overview of the used fungal...
-
The effects of selected factors on regional road fatalities – analysis of the Łódź region
PublikacjaAnalysis of regional accident records shows that a country’s national road safety programme does not have the same effect in each of its regions. What may be a serious problem in one region may be of marginal significance in another. Polish and international experience shows that main risk groups and types of accidents related to the level of development and quality of the road network differ from region to region. The conclusion...
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublikacjaThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
Accuracy analysis of 3D model obtained by photogrammetric method on the example of historic room from Wisłoujście Fortress
PublikacjaThe article presents a comparison of obtained models of a test object. Close range photogrammetry was used to obtain 3D models. As test object was used one of the rooms located in Wisłoujście Fortress in Gdańsk, Poland. Different models were obtained by using different distribution and number of reference points. Article contains analysis of differences between coordinates of control points obtained from total station measurements...
-
Impact of probability distribution on the uncertainty of resistance measurement
PublikacjaThe paper presents studies on the influence of probability distributions on the expanded uncertainty of the resistance measurement. Choosing the correct probability distribution is very important to estimate of measurement uncertainty. The paper presents the results of analysis of the resistance measurement uncertainty using the technical method of resistance: 100 G. The analysis of the uncertainty...
-
Overhead wires detection by FPGA real-time image processing
PublikacjaThe paper presents design and hardware implementation of real-time image filtering for overhead wires detection divided on image processing and results presentation blocks. The image processing block was separated from the whole implementation, and its delay and hardware complexity was analysed. Also the maximum frequency of image processing of the proposed implementation was estimated.
-
Improvement of the load capacity of the road overpass as a result of repairs after breakage caused by vehicle impacts
PublikacjaDamage of spans of the overpass caused by impact of underpassing vehicles are a frequent case. Objects that use prefabricated load-bearing elements that are not designed for such impacts are particularly exposed. After impact, such parts suffer extensive damage that need repair. Taking advantages of this recovery actions it is worth to perform strengthening that will protect object against possible future impacts. In this study...
-
Dimethyl ether (DME) as potential environmental friendly fuel
PublikacjaIn recent years, there has been a growing interest in replacing petroleum fuels with so-called second generation environmental friendly fuels. Compared to traditional petroleum fuels dimethyl ether (DME) could be used as a clean high-efficiency compression ignition fuel with reduced particulate matter (PM), sulfur oxides (SOx), hydrocarbons (HC), carbon monoxide (CO) as well as combustion noise. Compared to some of the other leading...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublikacjaExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Purification of model biogas from toluene using deep eutectic solvents
PublikacjaBiogas from landfills and wastewater treatment facilities typically contain a wide range of volatile organic compounds (VOCs), that can cause severe operational problems when biogas is used as fuel. Among the contaminants commonly occur aromatic compounds, i.e. benzene, ethylbenzene, toluene and xylenes (BTEX). In order to remove BTEX from biogas, different processes can be used. A promising process for VOCs removal is their absorption...
-
Lighting requirements for pedestrian crossings - positive contrast
PublikacjaFor many years now in Poland there has been a large number of road accidents at pedestrian crossings during night periods [5, 11]. One of the technical solutions that can improve this condition is the use of proper lighting for pedestrian crossings. The designated pedestrian crossing should be visible in different weather conditions and at different times of the day. In case of night vision restrictions use artificial lighting...
-
The flux compression generator load parameters selection
PublikacjaComputer simulation results of the flux compression generator (FCG) loaded with an inductor has been presented in this paper. Simulation research has been performed in order to select the parameters of FCG load coil properly. The influence of the load inductance and resistance on the current gain factor and the magnetic field energy accumulated in a load coil has been investigated.
-
Numerical simulations of overflow experiments on a model dike
PublikacjaDike failure due to overtopping is one of the important factors, which should be considered in the dike designing process. Although the overflow is characterized by the relatively low risk of occurrence, in many cases dikes are totally destroyed or seriously damaged. An interesting phenomenon occurring during overflow is the trapping of air in pores of the unsaturated soil material. As the infiltration progresses from all sides,...
-
The effects of vehicle restraint systems on road safety
PublikacjaKey to understanding the needs and tools of road infrastructure management for preventing run-off-road crashes or minimising their consequences, is to identify the hazads and sources of hazards caused by wrong or improper use of road safety devices and identify errors in the desifn, structure, construction and operation of road safety devices. Studying such an extended scope of the problem required fieldwork and surveys with road...
-
As- built inventory of the office building with the use of terrestrial laser scanning
PublikacjaTerrestrial Laser Scanning (TLS) is an efficient tool for building inventories. Based on the red- laser beam technology it is possible to provide the high accuracy data with complete spatial information about a scanned object. In this article, authors present the solution of use a TLS in as-built inventory of the office building. Based on the provided data, it is possible to evaluate the correctness of built details of a building...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Pedestrian and bicycle bridges as examples of safe collision-free road crossings
PublikacjaPedestrians are most at risk when they are crossing the road. This represents a significant proportion of all fatalities among pedestrians, amounting respectively to 50% in non-built-up areas and 75% in built-up areas. The most frequent reason for this accident is failure to give way. What is most terrible is that 30% of pedestrian accidents occurred at marked pedestrian crossings. Therefore, an important part of pedestrian safety...
-
New polish catalogue of typical flexible and semi-rigid pavements
PublikacjaThe paper covers the following topics important for the development of the new Polish Catalogue of typical flexible and semi-rigid pavements: reasons for preparing the new issue of the Catalogue of typical flexible and semi-rigid pavements, items introduced in the new issue, organise the terminology related to pavements, design traffic calculations and new equivalent axle load factors,...
-
Functionality of road safety devices - identification and analysis of factors
PublikacjaRoad safety devices are designed to protect road users from the risk of injury or death. The principal type of restraint is the safety barrier. Deployed on sites with the highest risk of run-off-road accidents, safety barriers are mostly found on bridges, flyovers, central reservations, and on road edges which have fixed obstacles next to them. If properly designed and installed, safety barriers just as other road safety devices,...
-
The guidelines and principles for planning and design of road restraint systems
PublikacjaThe project RID 3A Road Safety Equipment (RoSE) implemented by the Gdansk University of Technology within the RID programme, aims to conduct a comprehensive study and analyses of different vehicle containment systems (PN-EN 1317) and types of support structures (PN-EN 12767) and their performance. Within the project an analysis will be conducted of available research reports...
-
Speed management on local government managed roads – research, recommendations and guidelines
PublikacjaCommissioned by the National Road Safety Council Secretariat, the project “Guidelines for speed management on local government managed roads” studied car driver be haviour when subjected to selected speed management measures such a local speed restrictions, surveillance, traffic calming and restricted speed areas. In addition, analyses were conducted on the impact of selected me asures...
-
Bus bays inventory using a terrestrial laser scanning system
PublikacjaThis article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were...
-
Impact of ITS services on the safety and efficiency of road traffic
PublikacjaThis paper describes the project entitled: “Impact of the use of Intelligent Transport Systems on the level of road safety” (agreement no. DZP/RID-I-41/7/NCBR/2016), implemented as part of the Road Innovations Development (RID) programme, funded by the National Centre for Research and Development and the General Directorate for National Roads and Motorways (GDDKiA). The project is run by a consortium comprising the Motor Transport...
-
Testing the durability and function of road traffic management devices
PublikacjaTraffic management measures (vertical signs and horizontal marking, reflective elements) are used for guiding vehicles optically, indicating road mileage, marking objects in road gauge, marking vehicle and pedestrian safeguards and driver information and warning. This paper presents a synthesis of a literature study and the results of research conducted under stage one of the project LifeRoSE. The requirements for different traffic...
-
Conditions and capacity for implementing Poland’s vision zero
PublikacjaSince 1991 Poland has been systematically reducing its traffic hazard. Despite considerable progress Poland is still among the most dangerous countries in the European Union. The key types of actions that help to reduce fatalities include enhancement of pedestrian safety, reducing the number of speeding drivers and eliminating or reducing hazard on the road. The paper presents a brief diagnosis of the state of road safety in Poland...
-
Searching for road deformations using mobile laser scanning
PublikacjaMillions of people use roads every day all over the world. Roads, like many other structures, have an estimated durability. In Poland a lot of the roads were built at the turn of the 20th and 21st c., especially for light cars. Many of these roads carry traffic and heavy goods vehicles which were not predicted when the traffic was first estimated. It creates a lot of problems with technical conditions and the infrastructure must...
-
The safety issue of roadside advertising – comparison of polish and abu dhabi regulations
PublikacjaIn Poland a large number of advertisements are located by the roadside. These ads do not support road traffic management and unlike the road marking system are not subject to any regulations. The advertiser’s goal is to communicate a message to as many recipients as possible. Drivers with different individual abilities, such as attention focusing, eye accommodation, speed of information processing, can be distracted, blinded or...
-
Pedestrian safety in road traffic – studies, recommendations and proposed improvements
PublikacjaPedestrians are involved and most frequently the victims of every third road accident in Poland. Pedestrian accidents most frequently occur in complex circumstances, as a result of many factors related to the behaviour of drivers and pedestrians. The basic parameters that determine road safety include the perception of traffic and visibility on the road. The paper will present the results of research conducted within the project...
-
Comparison of requirements for location, maintenance and removal of road advertising between polish and foreign regulations
PublikacjaThe article gives an overview of Polish and international formal and legal requirements for roadside advertising and the relevant road safety impacts. The analysis focussed on outdoor advertising life cycle consisting of three stages: location, operation and removal of advertising. Experience of road authorities from Australia (Queensland), Republic of South Africa and the United Kingdom was collected. The article is part of a...
-
Methods of estimating the cost of traffic safety equipment’s life cycle
Publikacjan the article, the authors discuss the preliminary information necessary to determine the scope and direction of further research conducted within the project called “The influence of time and operating conditions on the durability and functionality of road safety elements”. The main objective of the project is to develop the concept of a method for optimizing the life cycle costs of road safety devices. The authors draw attention...