Filtry
wszystkich: 1975
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: 11th standard configuration
-
A concept for reducing PM 10 emissions for car brakes by 50%
PublikacjaWith regard to airborne particles with an aerodynamic diameter of less than 10 μm (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8–27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had the following aims: i) to demonstrate...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Małe miasta z funkcją przemysłową w aktywizacji obszarów peryferyjnych północnej Polski
PublikacjaBadaniami objęto małe miasta na obszarach peryferyjnych (czyli poza obszarami metropolitalnymi) w 3 województwach Polski północnej (pomorskim, warmińsko-mazurskim i zachodniopomorskim). Autor stawia tezę, że rozwój przemysłu w małych miastach może być ważnym czynnikiem rozwoju części obszarów peryferyjnych. Autor rozpoznaje poziom rozwoju funkcji przemysłowej miast i analizuje jego korelacje z niektórymi cechami miast i ich otoczenia....
-
Toward Safe and Efficient Recovery of Gas Munitions Dumped at Sea
PublikacjaThe proposal of a system for the safe recovery of unexploded ordnance (UXO), chemical weapons (CW) and chemicalwarfare agents (CWA) dumped at sea mainly after WWI and WWII is described in this work. The proposed solutionaddresses the tasks required to neutralise thousands of tons of dumped material and the currently available solutionsand proposed ideas. Requirements concerning the features of a recovery system are defined and...
-
Analogue GPS repeater
PublikacjaThis article concerns the problem of difficulty in correct indoor Global Positioning System (GPS) signals reception due to attenuation. Radio signal repeaters are proposed as means to solve this problem. Firstly, the GPS signal characteristics are described, emphasizing their low power in the point of reception. In the second part, various applications of GPS signal repeater, where indoor GPS signals reception is required, are...
-
Operating system security by integrity checking and recovery using write-protected storage
PublikacjaThe paper presents an Integrity Checking and Recovery (ICAR) system which protects file system integrity and automatically restores modified files. The system enables files cryptographic hashes generation and verification, as well as configuration of security constraints. All of the crucial data, including ICAR system binaries, file backups and hashes database are stored in a physically write protected storage to eliminate the...
-
Single-Anchor Indoor Localization Using ESPAR Antenna
PublikacjaIn this paper a new single-anchor indoor localization concept employing Electronically Steerable Parasitic Array Radiator (ESPAR) antenna has been proposed. The new concept uses a simple fingerprinting algorithm adopted to work with directional main beam and narrow minimum radiation patterns of ESPAR antenna that scans 360° area around the base station, while the signal strength received from a mobile terminal is being recorded...
-
The use of weight in motion data to heavy vehicles - pavement interaction analysis
PublikacjaWeight in motion (WIM) is the element of modern intelligent transport systems created to control commercial vehicles and to detect overloaded items. Because all of the vehicles crossing the WIM station are weighed and recognized, given data can be used to vehicle-pavement interaction analysis. The paper presents the results of analysis based on data from seven WIM stations localized in Motorway and National Roads in Poland. The...
-
The efficiency of pollutants removal and concepts on improvement for single-family TWs
PublikacjaIn the rural areas building of sewerage systems and central wastewater treatment plants (WWTPs) often brings too high costs, due to high distances from one farm to another and terrain configuration. Individual treatment systems for each farm are a good solution. Theteratment wetlands for nine individual farms were constructed in Kaszubian Lake District in summer and autumn 2009. Three configurations of hydrophyte beds were chosen....
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublikacjaThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
NVRAM as Main Storage of Parallel File System
PublikacjaModern cluster environments' main trouble used to be lack of computational power provided by CPUs and GPUs, but recently they suffer more and more from insufficient performance of input and output operations. Apart from better network infrastructure and more sophisticated processing algorithms, a lot of solutions base on emerging memory technologies. This paper presents evaluation of using non-volatile random-access memory as a...
-
Modular power converter topologies for energy storage and electric power distribution systems
PublikacjaThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. In order to achieve scalability of the system a modular approach is proposed. In addition to this different configuration of the system are analyzed, where depending on requirements and application a scalability in power, in energy capacity of energy storage resource and both in power and...
-
CeIr3: superconductivity in a phase based on tetragonally close packed clusters
PublikacjaWe present the crystallographic analysis, superconducting and spectroscopic characterization, and theoretical modeling of CeIr3. Lattice parameters a = 5.2945(1) Å and c = 26.219(1) Å are found for the R-3m symmetry crystal structure, which are close to the literature values. CeIr3 is a moderate type-II superconductor (κ GL = 17, λ e–p = 0.65) below 2.5 K. Ce ions exhibit a strongly intermediate valence character as evidenced by...
-
Innovative method for utilization of wastewater for security and safety in rural areas
PublikacjaIn the rural areas building of sewerage systems and central wastewater treatment plants (WWTPs) often brings too high costs, due to high distances from one farm to another and terrain configuration. Individual treatment systems for each farm are a good solution. The teratment wetlands for nine individual farms were constructed in Kaszubian Lake District in summer and autumn 2009. Three configurations of reed beds were chosen. In...
-
Study on the Influence of an Axial Distance Between Rotors on a Performance of a Small Counter-Rotating Wind Turbine
PublikacjaIn this paper, results of the investigation on the performance of a small counter-rotating wind turbinehas been presented. Computational Fluid Dynamics methodshave been used forwind turbine simulations. Rotors representation were introduced into computational domain by means of Actuator Line Model. Influence of an axial distance of CRWTrotorshas been investigated. In all studied configurations rotors were counter-rotating...
-
Artificial-Hand Technology—Current State of Knowledge in Designing and Forecasting Changes
PublikacjaThe subject of human-hand versatility has been intensively investigated for many years. Emerging robotic constructions change continuously in order to mimic natural mechanisms as accurately as possible. Such an attitude is motivated by the demand for humanoid robots with sophisticated end effectors and highly biomimic prostheses. This paper provides wide analysis of more than 80 devices that have been created over the last 40 years....
-
FINITE GROUND CPW-FED UWB ANTENNA OVER THE METALLIC CYLINDRICAL SURFACES
PublikacjaThe investigation of finite ground coplanar fed ultra-wideband (UWB) antenna and the influence of its curvature and the proximity of circular metallic screen on the reflection coefficients and radiation characteristics is presented. The antenna is composed of two circular coplanar strips which enclose slot aperture of similar shape and is designed on a thin and flexible substrate which allows its bending. The antenna configuration...
-
OPTIMISING RIG DESIGN FOR SAILING YACHTS WITH EVOLUTIONARY MULTIOBJECTIVE ALGORITHM
PublikacjaThe paper presents a framework for optimising a sailing yacht rig using Multi-objective Evolutionary Algorithms and for filtering obtained solutions by means of a Multi-criteria Decision Making method. A Bermuda sloop with discontinuous rig is taken under consideration as a model rig configuration. It has been decomposed into its elements and described by a set of control parameters to form a responsive model which can be used...
-
Computational modeling of molecularly imprinted polymers as a green approach to the development of novel analytical sorbents
PublikacjaThe development of novel molecularly imprinted polymers (MIP) sorbents for specific chemical compounds require a lot of tedious and time-consuming laboratory work. Significant quantities of solvents and reagents are consumed in the course of the verification of appropriate configurations of polymerization reagents. Implementation of molecular modeling in the MIP sorbent development process appears to provide a solution to this...
-
OPTIMALIZATION OF SORBENT FEEDING IN THE DRY METHOD OF FLUE GAS DESULFURIZATION
PublikacjaThe swiftly developing sea transport contributes to a considerable increase of fuel usage in the international shipping, which results in the escalation of toxic compounds emitted into the atmosphere. It is followed by the constantly heightened requirements limiting those emissions. In the case of sulfur oxide emission, inside of SECA (Sulfur Emission Control Area), the maximum content of sulfur in the shipping fuels used on the...
-
Pulsed UV-irradiated Graphene Sensors for Ethanol Detection at Room Temperature
PublikacjaA graphene-based gas sensor fabricated in a FET (GFET) configuration and its sensitivity towards ethanol and methane is reported. Detection of ethanol at the level of 100 ppm was observed under pulsed UV irradiation and after cleaning by UV light in the N2 ambient. Reduction of the frequency of UV irradiation pulses resulted in increased changes in sensor resistance in the presence of ethanol. Improved sensing behavior was ascribed...
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublikacjaAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublikacjaThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
Ultimate strength analysis of bulk carriers corrugated bulkheads
PublikacjaPrzedstawiono rozważania i obliczenia, których celem była ocena jakości standardu wytrzymałości grodzi falistych masowców, wprowadzonego w 1998 r. przez IACS i wdrożonego do konwencji SOLAS. Wykonane nieliniowe obliczenia MES nośności granicznej zginanych fal grodzi wykazują, że standard ten jest zbyt optymistyczny.
-
Application of Impedance Spectroscopy for Bi1−xNdxFeO3 Ceramics Characterization
PublikacjaIn the present paper the synthesis conditions for fabrication of Bi1−xNdxFeO3 ceramics are reported. The single phase polycrystalline samples of Bi1−xNdxFeO3 were prepared by standard solid state reaction method from the mixture of oxides viz.: Bi2O3, Fe2O3 and Nd2O3. The samples were characterized by impedance spectroscopy in the frequency range 10Hz – 1MHz at room temperature.
-
Simulation investigation of perovskite-based solar cells
PublikacjaThree models of thin-layer lead-halide perovskite solar cells with different electron-transport layers (TiO2,SnO2,ZnO) were investigatedby the simulation method. The perovskite layer thickness was optimized for all the systems. The analysis of the standard photovoltaic cell performanceparameters at various operating temperatures was performed. The best performance was achieved for the system with theSnO2conductive layer.
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Measurement of the tram rail profile during a year of operation
Dane BadawczeThe aim of the work was to analyze the wear of rails during operation and to analyze the supplementation of heavy metals in the soil around the tram route, originating from wearing out rails and tram wheels.The dataset contains measurements of rail head coordinates in 9 research sections made in 8 measurement series. The wear of the rails in selected...
-
Szacowanie estymaty menzurandu temperatury skóry człowieka podczas próby wysiłkowej
PublikacjaW artykule zaprezentowano wyniki pomiarów temperatury skóry człowieka podczas próby wysiłkowej. Ponieważ uzyskane wyniki nie podlegają rozkładowi normalnemu, wyznaczono wartości pięciu różnych estymatorów menzurandu. Otrzymane rezultaty wykazały, że w rozważanym przypadku najlepszy estymator menzurandu otrzymujemy z metody bootstrap, ponieważ charakteryzuje się on najmniejszym odchyleniem standardowym.
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublikacjaThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
Soxhlet Extraction and New Developments Such as Soxtec in: Comprehansive Sampling and Sample Preparation
PublikacjaSoxhlet extraction is one of the most popular techniques for extraction of analytes from solid materials. Since its discovery in 1879, the standard Soxhlet technique has been routinely applied in almost every analytical laboratory. Up to this day, Soxhlet extraction technique remains a standard technique to which the performance of modern extraction techniques is compared.Over the years, an intensive research on different modifications...
-
Analysis of abrasive particle trajectories during single-sided lapping process with driven conditioning ring
PublikacjaIn this paper new kinematics systems were studied for a single lapping process. In order to ensure the constant profile wear of the tool a standard kinematic system can be changed. Lapping is carried out by applying loose abrasive grains between two surfaces and causes a relative motion between them. The result is a finish of multi-directional lay. During process, the mechanism of surface formation are decisively affected by a...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublikacjaThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
ECG measurement from the hand with standing - hands resting on the device - Woman 27 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows in the air - Woman 27 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the table top - Man 29 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the armrests of the chair - Woman 27 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the armrests of the chair - Woman 49 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with standing - hands resting on the device - Man 29 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the table top - Woman 27 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows in the air - Man 29 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows to the body - Man 29 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows to the body - Woman 27 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with standing - hands resting on the device - Woman 49 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows to the body - Woman 49 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the armrests of the chair - Man 29 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows resting on the table top - Woman 49 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows in the air - Woman 49 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with standing - hands resting on the device - Man 30 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...
-
ECG measurement from the hand with elbows to the body - Man 53 age
Dane BadawczeThe data set shows the measurements of the ECG signal from the hand made with the use of the proprietary measuring system, based on the AD8232 and STM32 chips. Thanks to such a constructed device, it is possible to measure the ECG signal in a non-standard way - from the hand. The results show the ECG signal for a specific hand and forearm position relative...