Filtry
wszystkich: 1858
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXPERIMENTAL RESULTS
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublikacjaThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
Numerical Studies on Propellers in Open Water and behind Hulls aiming to support the Evaluation of Propulsion Tests
PublikacjaA RANS based numerical analysis of propellers can contribute considerably to our understanding of propeller/hull interaction. It may also allow for a review of scaling procedures on results from experimental fluid dynamics (EFD). Using various RANS codes (Fluent, CFX, STAR-CCM+ and FreSCo+) on common test cases the authors first focused on propeller open water (POW) calculations. Next we simulated the propeller hull interaction...
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublikacjaThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
Experimental Testbed of ASON/GMPLS architecture
PublikacjaThe paper presents the ASON/GMPLS architecture realized in the Department of Teleinformation Networks at Gdansk University of Technology based on the FSP 3000R7 ADVA Optical Networking platform. The FSP 3000R7 is a high-performance WDM networking system with GMPLS control plane for bidirectional transmission of optical signals. The system uses a modular structure which enables a flexible upgrade of capacity and functionality. The...
-
Influence of mesh density on 2D viscous flutter in a turbomachinery cascade
PublikacjaIn this study numerical simulations of 2D viscous flutter were performed and compared with available experimental results for various mesh densities and flow parameters. Calculations were carried out for the bending oscillations of an Eleventh Standard Configuration cascade. ANSYS CFX code was used for the SST, SA and k-ω turbulence model calculations.
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublikacjaPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublikacjaThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Similarity Measures for Face Images: An Experimental Study
PublikacjaThis work describes experiments aimed at finding a straightforward but effective way of comparing face images.We discuss properties of the basic concepts, such as the Euclidean, cosine and correlation metrics, test the simplest version of elastic templates, and compare these solutions with distances based on texture descriptors (Local Ternary Patterns). The influence of selected image processing methods (e.g. bilateral ltering)...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
The fracture behaviour of notched PMMA specimens under simple loading conditions – Tension and torsion experimental tests
PublikacjaThis paper presents the results of experimental testing of flat PMMA specimens during uniaxial loading conditions. Two separate tests were conducted: tensile and torsion. The specimens were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. The specimens were made in two thickness variants: 5 and 15 mm. Monotonic tensile and torsion tests were carried out while keeping the averaged strain rate constant,...
-
Long-term follow-up of MCL patients treated with single-agent ibrutinib: updated safety and efficacy results
Publikacja -
Types of Depression More Frequent in Bipolar than in Unipolar Affective Illness: Results of the Polish DEP-BI Study
Publikacja -
The outcomes of Re-Redo bariatric surgery—results from multicenter Polish Revision Obesity Surgery Study (PROSS)
Publikacja -
DEVELOPMENT OF HYDROGEL CAPSULES FOR USE IN DUAL-PHASE TOPICAL PREPARATIONS CONTAINING DIHYDROXYACETONE AND AMINO ACIDS – PRELIMINARY RESULTS
Publikacja -
Verification of the theoretical methods for the prediction of resistance of sailing yachts based on model test results of a yacht V.O.60
PublikacjaWeryfikacja opiera się głównie na serii systematycznych badań modelowych wykonanych w roku 2001 w Laboratorium Hydromechaniki Okrętu WOIO PG. Zademonstrowano prognozy oporu jachtu wykonane trzema metodami z oszacowaniem i dyskusją rozbieżności wyników. Przeprowadzone badania są zorientowane na opracowanie wiarygodnego programu komputerowego dla prognozowania prędkości i innych parametrów ruchu żaglowych, regatowych jachtów oceanicznych...
-
Comparison of luminescence (TL and OSL) dating results from selected loess profiles in SE Poland and the NW Ukraine
PublikacjaFive periglacial loess profiles, three from Poland and two from the Ukraine, were selected from dating luminescence methods (TL and OSL). In regional terms, they include loess of the Carpathin, peri-Carpathian and Podalia facies. 89 samples were collected for dating purposes from five profiles. Of these samples, 19 were OSL-dated. The function of TL and OSL date distribution for the same samples was presented on one chart. The...
-
DETERMINATION OF THE EFFECT OF ENVIRONMENTAL FACTORS ON THE CORROSION OF WATER DISTRIBUTION SYSTEM BASED ON ANALYSIS OF ON-LINE CORROSION MONITORING RESULTS
PublikacjaCorrosion of water distribution system is a significant issue causing problems with quality, safety and continuity of distribution. The changes of corrosion rates of the water distribution systems in Cracow made of carbon steel were investigated by analysis of online corrosion monitoring system results. Corrosion rates were determined using the linear polarization method. The impact of rain, temperatures, conductivity, dissolved...
-
A simplified approach to determine the expiration date of certified reference material based on the results of monitoring long-term stability
PublikacjaAll components of the quality assurance (QA) system for measurement results depend heavily on certified reference materials (CRMs). There is a need for a comprehensive discussion of the stability study using the CRM statistical method. Monitoring involves periodic sampling and analysis of the CRM at predetermined intervals to continuously monitor stability without compromising its integrity. The obtained stability data is then...
-
LSA Is not Dead: Improving Results of Domain-Specific Information Retrieval System Using Stack Overflow Questions Tags
PublikacjaThe paper presents the approach to using tags from Stack Overflow questions as a data source in the process of building domain-specific unsupervised term embeddings. Using a huge dataset of Stack Overflow posts, our solution employs the LSA algorithm to learn latent representations of information technology terms. The paper also presents the Teamy.ai system, currently developed by Scalac company, which serves as a platform that...
-
Relationship between GIX, SIDX, and ROTI ionospheric indices and GNSS precise positioning results under geomagnetic storms
PublikacjaIonospheric indices give information about ionospheric perturbations, which may cause absorption, diffraction, refraction, and scattering of radio signals, including those from global navigation satellite systems (GNSS). Therefore, there may be a relationship between index values and GNSS positioning results. A thorough understanding of ionospheric indices and their relationship to positioning results can help monitor and forecast...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublikacjaThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
From the Concept to Results: A Case Study on the Collection Development for the ODC–Opening Day Collection at Qatar National Library
Publikacja"A library collection should fit the mission for which it is created. The number of books it holds does not determine its worth." (E. J. Loveland, 2000) If so, how do we create a national library, and how do we build its collection from scratch without making many mistakes? Since 2012, when the plans for the new national library were announced, Qatar National Library (QNL) envisioned as carrying out its mission to "spread knowledge,...
-
COMPARATIVE ANALYSIS OF RESULTS OF APPLICATION OF MARKOV AND SEMI-MARKOV PROCESSES TO RELIABILITY MODELS OF MULTI-STATE TECHNICAL OBJECTS
PublikacjaDuring rational operation of technical objects and systems various operational decisions are made and decision-making process itself should be consisted in selecting that considered most favourable out of all possible to be taken. Choice of such decision is possible after taking into account many different information items but it never be completely correct without accounting for data and indices dealing with reliability. In...
-
Mentor&Student Research Lab: new type of architectural and urban design workshops, new opportunities, valuable results
PublikacjaThe space around us has significantly changed during last years. Polish cities have undergone a major transformation following political, economical and social transition [8]. Similar change is noticeable at universities and their educational programmes for architecture and spatial planning students. Nowadays designers and activists tackle completely different problems and have different opportunities than their older colleagues...
-
GPR investigation of the strengthening system of a historic masonry tower
PublikacjaIn this paper the condition assessment of the strengthening system of a masonry tower was carried out by the GPR method. The study provided unique experimental data acquired during measurements of the reinforced concrete frame embedded in masonry walls. Conducted numerical and experimental investigations were focused on the phenomenon of the diffraction-refraction scattering of the electromagnetic energy. A hyperbola resulting...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Effect of Time Varying Measurement Conditions on Antenna Pattern in Near Field Measurement and Its Correction Procedure
PublikacjaAuthors present the procedure of taking into account the changes of electrical parameters of setup due to the time drift of temperature during the procedure of near field measurement. It is proposed to make additional measurements in determined positions of probe are next used the results to introduce corrections terms in measured data. Such approach was verified practically in experimental near field measurement system.
-
Five-phase Induction Motor Drive Operation During Stator Phase Fault
PublikacjaThe article presents the most important advantages of multi-phase electric drives. The construction of a five-phase squirrel cage induction motor together with possible stator winding distribution cases is presented, which affect the properties of such motor. Increased reliability of five-phase drives was indicated. The drive operation properties were confirmed by experimental results.
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
A Review of Reduction Methods of Impact of Common-Mode Voltage on Electric Drives.
PublikacjaIn this survey paper, typical solutions that focus on the reduction in negative effects resulting from the common-mode voltage influence in AC motor drive applications are re-examined. The critical effectiveness evaluation of the considered methods is based on experimental results of tests performed in a laboratory setup with an induction machine fed by an inverter. The capacity of a common-mode voltage level reduction and voltage...
-
The statistical impact of experimental result scatter of asphalt mixtures on their numerical modelling
PublikacjaThe paper presents selected test results of asphalt mixture conducted in low temperatures. The obtained parameters are highly diverse. It concerns ultimate breaking loads, stiffness parameters related to Young's modulus but also the fracture course. Statistical analysis upon the results makes it possible to relevantly estimate the material-defining parameter values. Such a random approach leads to the mean values of breaking and...
-
The influence of microjet array area ratio on heat transfer in the compact heat exchanger
PublikacjaThe paper describes the comprehensive study on the effect of microjet array geometrical parameters on the heat transfer enhancement in the modular heat exchanger. The conducted experimental study provides an experimental database on single phase submerged microjet heat transfer. The Wilson plot method was applied to determine the heat transfer coefficients in the laminar and transition flow regimes of a liquid-to-liquid heat exchanger....
-
Psychological inspirations in empirical software engineering.
PublikacjaSoftware development is people-intensive activity. Incorporation of human factors in empirical studies of software engineering can bring many benefits for both researchers and practitioners. Psychological inspirations can facilitate this task. In this paper, such incorporation is presented in the contexts of the objectives and problems in empirical studies, applicability of the results in the business context of software enterprise,...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublikacjaThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Damage detection in a bolted lap joint using guided waves
PublikacjaThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
The influence of water and mineral oil on volumetric losses in a hydraulic motor
PublikacjaIn this paper volumetric losses in hydraulic motor supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and comparison. The experimental tests were conducted using an innovative hydraulic satellite motor, that is dedicated to work with different liquid, including water. The sources of leaks in this motor are characterized and described also. On this...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublikacjaThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublikacjaThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
UHF ESPAR antenna for simple Angle of Arrival estimation in UHF RFID applications
PublikacjaAn electronically switched beam antenna for localization of passive UHF RFID tags based on a simple Angle of Arrival (AoA) technique is proposed‥ Detailed antenna design and realization are presented together with corresponding simulations and measurement results. Experimental tests with passive UHF RFID tag show the validity of theoretical assumptions for application of the antenna in UHF RFID based localization systems.
-
Metoda diagnostyki łożysk na podstawie analizy przebiegów prądu i napięcia zasilającego silnik indukcyjny.
PublikacjaW niniejszej monografii przedstawiono oryginalne podejście i realizację diagnostyki łożysk silników indukcyjnych przy użyciu metody opartej na pomiarach i analizie iloczynu wartości chwilowych prądu i napięcia zasilającego maszyny. Uzyskane wyniki badań eksperymentalnych na obiektach rzeczywistych okazały się zbieżne z wynikami badań symulacyjnych i potwierdziły, że powstanie uszkodzeń łożysk w silniku skutkuje pojawieniem się...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublikacjaDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Cylindrical orifice testing in laminar flow with the orifice diameter ratio β = 0.5
PublikacjaThe paper presents the results of an experimental study of a cylindrical orifice with the orifice diameter ratio β = 0.5 and the flow opening length‑to‑diameter ratio L/d = 1, with hydraulic oil flowing in the DN50 measuring channel. The measurements of the values characterising the oil flow were made in the laminar flow regime, for the Reynolds numbers ranging between Re = 100 to 950. Based on the experimental tests, standard...
-
Effect of tube bundle arrangement on performance of shell-and-tube latent heat storage system
PublikacjaThis work presents the results of experimental investigation on charging and discharging of latent heat storage systems (LHSS) in the form of shell-and-tube heat exchangers with a variable arrays of the tube bundles. The tests included two tube arrangements – in-line and triangular (staggered), a variable number of tubes in a bundle, two pitch ratios, and different tube positions in a bundle. Three commercial products (LTP56, RT54HC,...
-
Modelling, Simulation and Optimization of the Wavemaker in a Towing Tank
PublikacjaThe paper analyses the problem of experimental identification (frequency response), modelling and optimization of the towing tank wavemaker in the Scilab/Xcos environment. The experimental identification of the objects (the towing tank wavemaker placed in the hydrodynamic laboratory of the CTO S.A. Ship Design and Research Centre (CTO)) and the implementation of the models in the simulation environment, enable to perform: 1. tuning...
-
Flexural behavior of composite structural insulated panels with magnesium oxide board facings
PublikacjaThe current report is devoted to the flexural analysis of a composite structural insulated panel (CSIP) with magnesium oxide board facings and expanded polystyrene (EPS) core, that was recently introduced to the building industry. An advanced nonlinear FE model was created in the ABAQUS environment, able to simulate the CSIP’s flexural behavior in great detail. An original custom code procedure was developed, which allowed to include...
-
Dynamics of algae growth and nutrients in experimental enclosures culturing bighead carp and common carp: Phosphorus dynamics
PublikacjaThis is the third paper of the series about “Dynamics of algae growth and nutrients in experimental enclosures culturing bighead carp and common carp”. In this paper, phosphorus dynamics were investigated under the condition of culturing bighead carp and common carp with added fish food (nitrogen dynamics is discussed in the second paper because their behaviors are so different from each other). Nearly fifty days’ observation results...
-
Calculation of electron scattering lengths on Ar, Kr, Xe, Rn and Og atoms
PublikacjaFocusing on the noble gases, we calculate the scattering potential using the Dirac-Coulomb Hamiltonian supplemented with a model polarization potential. We determine the scattering lengths using two methods, namely phase shifts for very small scattering energies and the shape of the wave function for zero scattering energy. We compare our theoretical electron scattering length results on Ar, Kr and Xe atoms with existing experimental...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublikacjaDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublikacjaThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...