wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: ATOMIC FORCE MICROCOPY
-
Scattering of electrons by a 1,2-butadiene (C4H6) molecule: measurements and calculations
PublikacjaWe present the results of experimental and theoretical study on electron collisions with a 1,2-butadiene (H2C=C=CHCH3) molecule. Absolute grand-total cross sections (TCSs) were measured using a linear electron-transmission method for collision energies in the 0.5–300 eV range. Two distinct features in the TCS energy curve were detected: a narrow peak located at 2.3 eV and a broad enhancement centered around 9 eV. We attributed...
-
Electron scattering from hexafluoroacetone molecules: cross section measurements and calculations
PublikacjaZmierzono absolutne całkowite przekroje czynne na zderzenie elektronów z drobinami hexafluoroacetonu (HFA). Pomiary przeprowadzono dla energii zderzenia od 1 do 400 eV. Zależność energetyczna przekroju czynnego wykazała obecność struktur związanych z procesami o charakterze rezonansowym. Wykonano obliczenia sprężystego i jonizacyjnego przekroju czynnego dla drobin HFA i acetonu. Suma obliczonych przekrojów wykazuje dużą zgodność...
-
Electron scattering cross sections for 1-pentene, H2C=CH-(CH2)2CH3, molecules
PublikacjaCross sections, both experimental and theoretical, are reported for electron scattering from 1-pentene (C5H10) molecules. Absolute grand-total cross sections (TCSs) were measured at electron impact energies ranging from 1 to 300 eV, using a linear electron-transmission technique. The dominant behaviour of the experimental TCS energy function is a distinct asymmetric enhancement with the maximum located around 6.5 eV. Discernible...
-
Scattering of electrons from 1-butene, H2C=CHCH2CH3, and 2-methylpropene,H2C=C(CH3)2, molecules
PublikacjaZmierzono, wykorzystując liniową technikę transmisyjną, całkowite absolutne przekroje czynne (TCS) na rozpraszanie elektronów na cząsteczce 1-butenu (H2C=CHCH2CH3) oraz 2-metylpropene (H2C=C(CH3)2) w zakresie energii padających elektronów, od 1 do 400 eV oraz od 1 do 350 eV. Kształt przekroju czynnego dla obu badanych izomerów butenu jest podobny. Dwie struktury w uzyskanych krzywych TCS, są wyraźnie widoczne: mały pik w okolicy...
-
Theoretical and experimental study on scattering of low-energy electrons by dimethyl and diethyl ethers
PublikacjaWe report a joint theoretical and experimental investigation on low-energy electron scattering by dimethyl and diethyl ethers. The experimental elastic differential cross sections were measured at impact energies from 1 eV up to 30 eV and scattering angle range of 10◦ to 130◦. Theoretical elastic differential, integral and momentum-transfer cross sections are calculated at impact energies up to 30 eV, employing the Schwinger multichannel...
-
Low energy inelastic electron scattering from carbon monoxide: II. Excitation of the b3Σ+, j3Σ+, B1Σ+, C1Σ+ and E1Π Rydberg electronic states
PublikacjaIn this second part of a two part paper (first part: Zawadzki et al (2020 J. Phys. B: At. Mol. Opt. Phys. 53 165201)) we present differential scattering cross sections for excitation of several Rydberg electronic states of carbon monoxide by electron impact. The first part concerned the low-lying valence states of CO. In the present study cross sections are obtained experimentally using low-energy electron energy-loss spectroscopy...
-
Isomer effects on the total cross section for electron scattering from C4F6molecules.
PublikacjaZmierzono całkowity przekrój czynny (TCS) na rozpraszanie elektronów na drobinach 1,3-C4F6. Pomiary przeprowadzono w zakresie energii elektronu od 0,6do 370 eV. Wyniki porównano z TCS otrzymanym poprzednio dla 2-C4F6. Stwierdzono wpływ różnic strukturalnych na otrzymane energetyczne zależności TCS (tzw. efekt izomeryczny).
-
Electron scattering from C4H6 and C4F6 molecules.
PublikacjaZmierzono całkowity przekrój czynny (TCS) na zderzenie elektronów z izomerami C4H6 i z drobiną C4F6. Pomiary przeprowadzono w oparciu o liniową metodę transmisyjną. Dla izomerów C4H6 stwierdzono różnice w kształcie i wielkości TCS w obszarze niskich energii. Wskazano na efekt fluoryzacji.
-
Mercury concentrations in marine biota with special focus on grey and ringed seals
PublikacjaMarine organisms are exposed and sensitive to effects of environmental contamination by heavy metals including different forms of mercury. Baltic seals as the top predators of the marine ecosystem are even more endangered due to (considerable) longevity as well as a long biological half-time of toxin elimination. The concentrations of mercury in seals from the Baltic is poorly known, thus the aim of this work is to determine and...
-
BASECOL2023 scientific content
PublikacjaContext. The global context of making numerous data produced by researchers available requires collecting and organising the data, assigning meaningful metadata, and presenting the data in a meaningful and homogeneous way. The BASECOL database, which collects inelastic rate coefficients for application to the interstellar medium and to circumstellar and cometary atmospheres, meets those requirements. Aims. We aim to present the...
-
Electron-impact dissociation of molecular hydrogen: benchmark cross sections
PublikacjaWe present a joint experimental and theoretical investigation of a fundamental process in atomic and molecular physics: electron impact excitation of molecular hydrogen’s (H2) most dominant transition (X1Σg+ → b3Σu+). Excitation of this state is by far the main channel that causes the dissociation of H2 into H + H atoms at low energies. The Convergent Close-Coupling (CCC) calculations predicted significant, more than factor of...
-
Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor
PublikacjaWe report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C....
-
Flexomagneticity in buckled shear deformable hard-magnetic soft structures
PublikacjaThis research work performs the first time exploring and addressing the flexomagnetic property in a shear deformable piezomagnetic structure. The strain gradient reveals flexomagneticity in a magnetization phenomenon of structures regardless of their atomic lattice is symmetrical or asymmetrical. It is assumed that a synchronous converse magnetization couples both piezomagnetic and flexomagnetic features into the material structure....
-
Thermal buckling of functionally graded piezomagnetic micro- and nanobeams presenting the flexomagnetic effect
PublikacjaGalerkin weighted residual method (GWRM) is applied and implemented to address the axial stability and bifurcation point of a functionally graded piezomagnetic structure containing flexomagneticity in a thermal environment. The continuum specimen involves an exponential mass distributed in a heterogeneous media with a constant square cross section. The physical neutral plane is investigated to postulate functionally graded material...
-
Ultrasound assisted dispersive solid phase microextraction using polystyrene-polyoleic acid graft copolymer for determination of Sb(III) in various bottled beverages by HGAAS
PublikacjaA new polyoleic acid-polystyrene (PoleS) block/graft copolymer was synthesized and applied as adsorbent for ultrasound assisted dispersive solid phase microextraction (UA-DSPME) of Sb(III) in different bottled beverages and analysis using hydride generation atomic absorption spectrometry (HGAAS). Adsorption capacity of the PoleS was 150 mg g−1. Several sample preparation parameters such as sorbent amount, solvent type, pH, sample...
-
Collision Strengths of Astrophysical Interest for Multiply Charged Ions
PublikacjaThe electron impact excitation and ionization processes are crucial for modeling the spectra of different astrophysical objects, from atmospheres of late-type stars to remnants of supernovae and up to the light emission from neutron star mergers, to name just a few. Despite their signifi- cance, however, little is known quantitatively about these processes for low- and medium-impact energies of, say, Ekin . 5000 eV of the free...
-
The EU enlargement and domestic employment
PublikacjaThe study focuses on the interactions between EU member states' labor markets (manufacturing and tradable business services) over the period 1995-2005. We use recently released detailed sector level employment statistics, considering the effects of trade integration on the creation of links between labor force in ''Old'' and ''New'' partners in the enlarged EU. Empirical estimations show that the domestic demand for labor in the...
-
Comparison of classical Winter's bracing requirements of compressedtruss chord with stability analysis of 3D truss-model
PublikacjaMost code requirements concerning bracing are based on principles developed by Winter. The present research is devoted tostudy a lateral buckling of truss with linear elastic side supports. The classical Winter's model of truss chord in the case ofout of the truss plane buckling is compared with nonlinear analysis of 3D truss model. Full bracing condition, that permitsthe truss chord to support load level corresponding to an unbraced...
-
Application of magnetic nanoparticles for magnetic solid-phase extraction in preparing biological, environmental and food samples
PublikacjaThe need to obtain meaningful results as the basis for determining the content of trace amounts of analytes has become the driving force behind the development of modern analytical techniques, including sample-preparation techniques, such as solid-phase extraction (SPE). Recently, great interest was aroused in the use of magnetic nanoparticles (MNPs) in SPE. These materials exhibit high selectivity, and, in small amounts, can provide...
-
A NOTE ON ON-LINE RAMSEY NUMBERS FOR QUADRILATERALS
PublikacjaWe consider on-line Ramsey numbers defined by a game played between two players, Builder and Painter. In each round Builder draws an the edge and Painter colors it either red or blue, as it appears. Builder’s goal is to force Painter to create a monochromatic copy of a fixed graph H in as few rounds as possible. The minimum number of rounds (assuming both players play perfectly) is the on-line Ramsey number \widetilde{r}(H) of...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublikacjaIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Engineering method of tire rolling resistance evaluation
PublikacjaTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
State-of-the-art ideas for engineering laboratory classes – virtual reality framework
PublikacjaNowadays challenges in science and technology are a driving force in the development of contemporary solutions in education. Virtual reality brings to an edge human imagination. In this paper, authors propose a framework for civil engineering laboratory classes which brings a new quality in this area. The framework shows how to provide learners with an environment where they can realize the health and safety hazards of construction...
-
Impact resistance of plain and twill fabric in GFRP measured by active thermography
PublikacjaThis paper discusses the impact resistance of glass-fibre reinforced polymer (GFRP) composites depending on the type of reinforcement – plain or twill weave. The values of impact energy were: 3J, 10J and 15J. Specimens featuring twill weave transferred higher force during the impact as compared with plain weave specimens. It was observed that an increase of impact energy was accompanied by an increase of the disproportion in...
-
LDFEM analysis of FDP auger installation in cohesive soil
PublikacjaThis paper deals with large deformation finite element (LDFE) preliminary modelling of Full Displacement Pile (FDP) installation in cohesive soil deposit located in Jazowa, Poland. The detailed FDP auger geometry is applied and the drilling process is modelled with full 3D Coupled Eulerian-Lagrangian (CEL) formulation. The total stress approach and elastic-perfectly plastic model with rate-dependent Mises plasticity is used. The...
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublikacjaSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
Evaluation of the prediction ability of air pollutants based on the electronic nose responses
PublikacjaElectronic noses are able to perform on-line measurements of the toxic volatile compounds in air. Due to their low cost and compact size they can be placed in the areas exposed to pollution, outside the laboratory. Those advantages, on the other side, force the need for development of the reliable sensors data analysis procedures. One of the most important issues connected with electronic noses is the lack of stability of the gas...
-
Comparative testing of numerical models of river ice jams
PublikacjaIce processes in general, and ice jams in particular, play a dominant role in the hydrologic regime of Canadian rivers, often causing extreme floods and affecting the life cycle of many aquatic, terrestrial, and avian species. Various numerical models have been developed to help simulate the formation and consequences of these very dynamic and often destructive jam events. To test and compare the performance of existing models,...
-
The point estimate method in a reticulated shell reliability analysis
PublikacjaThe objective of this paper is to present an application of the point estimate method (PEM) that can determine the probabilistic moments for engineering structures. The method is reasonably robust and adequately accurate for a wide range of practical problems. It is a special case of numerical quadrature based on orthogonal polynomials. The main advantage of this method is that, unlike FORM or SORM, it is not necessary to carry...
-
A PRELIMINARY STUDY ON THE OPTIMAL CHOICE OF AN IMPLANT AND ITS ORIENTATION IN VENTRAL HERNIA REPAIR
PublikacjaThis paper addresses the problem of ventral hernia repair. The main goals are to find an optimal surgical mesh for hernia repair and to define its optimal orientation in the abdominal wall to minimise the maximum force at the tissue-implant juncture. The optimal mesh is chosen from a set of orthotropic meshes with different stiffness ratios for typical hernia placement in the abdominal area. The implant is subjected to an anisotropic...
-
A spatio-temporal approach to intersectoral labour and wage mobility
PublikacjaThe article presents the spatio-temporal approach for intersectoral labor and wage mobility. Analyses of interindustry mobility were performed with the use of general entropy mobility indices (GEMM). Spatio- temporal approach was obtained thanks to the separate measurement of spatial autocorrelation and regression for each set of sectoral wage and employment structure and was conducted in each year of the research period separately....
-
A Spatio-temporal Approach to Intersectoral Labour and Wage Mobility
PublikacjaThe article presents the spatio-temporal approach for intersectoral labor and wage mobility. Analyses of interindustry mobility were performed with the use of general entropy mobility indices (GEMM). Spatio-temporal approach was obtained thanks to the separate measurement of spatial autocorrelation and regression for each set of sectoral wage and employment structure and was conducted in each year of the research period separately....
-
Long‐time scale simulations of virus‐like particles from three human‐norovirus strains
PublikacjaThe dynamics of the virus like particles (VLPs) corresponding to the GII.4 Houston, GII.2 SMV, and GI.1 Norwalk strains of human noroviruses (HuNoV) that cause gastroenteritis was investigated by means of long-time (about 30 μs in the laboratory timescale) molecular dynamics simulations with the coarse-grained UNRES force field. The main motion of VLP units turned out to be the bending at the junction between the P1 subdomain (that...
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublikacjaIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Dependence of Power Characteristics on Savonius Rotor Segmentation
PublikacjaSavonius rotors are large and heavy because they use drag force for propulsion. This leads to a larger investment in comparison to horizontal axis wind turbine (HAWT) rotors using lift forces. A simple construction of the Savonius rotor is preferred to reduce the production effort. Therefore, it is proposed here to use single-segment rotors of high elongation. Nevertheless, this rotor type must be compared with a multi-segment...
-
Extended Newmark method to assess stability of slope under bidirectional seismic loading
PublikacjaThe paper concerns the dynamic behavior of a simple slope model subjected to simultaneous horizontal and vertical excitations. The proposed method is based on Newmark’s sliding block concept, however, four new features are introduced. The most important assumption is that the normal component of dynamic excitations affects the resisting force both before and after the initiation of the relative slope motion, making it time-dependent....
-
Relative Productivity, Country Size and Export Diversification
PublikacjaThis paper analyses the effects of productivity and country size on the extent of trade structure diversification. Using a testable version of the Ricardian model, we show that relative export variety is an outcome of two forces: a relative productivity change (technological progress) and a relative country size change (labour force growth). The model predictions are validated empirically using product-level trade data for a sample...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
REVIEW OF CURRENT RESEARCH ON CHITOSAN AS A RAW MATERIAL IN THREE-DIMENSIONAL PRINTING TECHNOLOGY IN BIOMEDICAL APPLICATIONS
PublikacjaThree-dimensional (3D) biomaterial manufacturing strategies show an extraordinary driving force for the development of innovative solutions in the biomedical sector, including drug delivery systems, disease modelling and tissue and organ engineering. Due to its remarkable and promising biological and structural properties, chitosan has been widely studied for decades in several potential applications in the biomedical field. However,...
-
UNRES-GPU for Physics-Based Coarse-Grained Simulations of Protein Systems at Biological Time- and Size-Scales
PublikacjaThe dynamics of the virus like particles (VLPs) corresponding to the GII.4 Houston, GII.2 SMV, and GI.1 Norwalk strains of human noroviruses (HuNoV) that cause gastroenteritis was investigated by means of long-time (about 30 μs in the laboratory timescale) molecular dynamics simulations with the coarse-grained UNRES force field. The main motion of VLP units turned out to be the bending at the junction between the P1 subdomain (that...
-
Tensile test results of fused filamend fabricated polylactyde and polylactyde with carbon fiber filler
Dane BadawczeThe Dataset contains the results of the mechanical behaviour of dog-bone shaped specimens. The specimens were additively manufactured with the fused filament fabrication (FFF) method. They used two different materials polylactide (PURE PLA) and polylactide with carbon fibre filler (PLA+CF). The specimens were segregated into three groups - unsterilized,...
-
Oferta kształcenia a wymogi współczesnego rynku pracy
PublikacjaWspółcześnie zmianom ulegają struktury gospodarek oraz sposoby gospodarowania poszczególnymi zasobami na rynkach. Wpływ na to mają nowoczesne technologie, procesy globalizacji i integracji. Obserwowane dynamiczne zmiany wymuszają włączenie się w proces unowocześniania różnych uczestników rynku. Jednym z nich są instytucje zajmujące się szeroko rozumianym kształceniem, które przygotowują zasoby pracy do wejścia na rynek pracy. Celem...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Experimental and predicted physicochemical properties of monopropanolamine-based deep eutectic solvents
PublikacjaIn this work, the novel deep eutectic solvents (DESs) based on 3-amino-1-propanol (AP) as hydrogen bond donor (HBD) and tetrabutylammonium bromide (TBAB) or tetrabutylammonium chloride (TBAC) or tetraethylammonium chloride (TEAC) as hydrogen bond acceptors (HBAs) were synthesized with different molar ratios of 1: 4, 1: 6 and 1: 8 salt to AP. Fourier Transform Infrared Spectroscopy measurements were performed to provide an evidence...
-
Magnetic hydrophobic deep eutectic solvents for orbital shaker-assisted dispersive liquid-liquid microextraction (MAGDES-OS-DLLME) - determination of nickel and copper in food and water samples by FAAS
PublikacjaIn this work, a cheap and widely applicable dispersive liquid-liquid microextraction (DLLME) method was developed for the extraction of Ni(II) and Cu(II) from water and food samples and analysis using flame atomic absorption spectrometry. DLLME was assisted by orbital shaker, while ferrofluid as an extractant was based on deep eutectic solvent (DES). This ferrofluid was made of hydrophobic DES (hDES), composed of lauric acid and...
-
Experimental and predicted physicochemical properties of monopropanolamine-based deep eutectic solvents
PublikacjaIn this work, the novel deep eutectic solvents (DESs) based on 3-amino-1-propanol (AP) as hydrogen bond donor (HBD) and tetrabutylammonium bromide (TBAB) or tetrabutylammonium chloride (TBAC) or tetraethylammonium chloride (TEAC) as hydrogen bond acceptors (HBAs) were synthesized with different molar ratios of 1:4, 1:6 and 1:8 salt to AP. Fourier Transform Infrared Spectroscopy measurements were performed to provide an evidence...