Wyniki wyszukiwania dla: MICRO-CHP ORC SYSTEM
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublikacjaThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Optimization of an axial turbine for a small scale ORC waste heat recovery system
Publikacja -
Restructuring of CHP utilities as a way of power system capacity increase as well as economic and ecological characteristics improvement systems.
PublikacjaPrywatyzacja polskiego rynku energii elektrycznej i cieplnej spowoduje zmiany w elektrociepłowniach i elektrowniach przemysłowych. Rezultatem modernizacji są zmiany ekonomiczne i ekologiczne. Przedstawiono możliwość zmniejszenia emisji związków siarki i zwiększenie sprawności elektrowni poprzez dobudowanie do układu konwencjonalnego zespołu turbin gazowych opalanych gazem naturalnym.
-
Systematic and Selection Criteria for ORC System Working Fluid Used for a Determined Amount of Excessive Energy
PublikacjaPoprawa sprawności energetycznej procesów technologicznych stanowi obecnie - obok ograniczenia emisji gazów cieplarnianych i wykorzystania alternatywnych źródeł do produkcji energii - najważniejszy element idei zrównoważonego rozwoju. Niniejsza praca wychodzi naprzeciw rynkowym oczekiwaniom. wskazując możliwości wpisania się w ten trend. W procesach technologicznych ciepło odpadowe stanowi nie zawsze do końca rozwiązany problem....
-
Experimental investigations on water sorptivity in mortars with the use of X-ray micro-CT system.
PublikacjaW pracy doswiadczalnej zbadano zjawisko sorpcji wody w pryzmatycznych próbkach zapraw, które jest ściśle powiązane z trwałością materiału. Sorpcyjność oceniana na etapie ustalonym w połączeniu z warunkami zewnętrznymi może być wykorzystana do przewidywania okresu użytkowania. Sorpcyjność początkową i wtórną wody w próbkach zapraw nienasyconych zmierzono w badaniach laboratoryjnych zgodnie z normą amerykańską ASTM C 1585–04. Wpływ...
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublikacjaDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Specificity of automatic control of micro-turbines (steam or gas -driven and expanders) in dispersed generation system of heat and electric power
PublikacjaThis paper presents specific problems of automatic control of steam micro-turbines and expanders intended for the dispersed, combined generating of heat and electric power. The investigations concern ensurance of certainty of energy supply and its required quality.
-
Luminescent properties of undoped and Ce3+ doped crystals in Y2O3 Lu2O3 Al2O3 triple oxide system grown by micro-pulling-down method
Publikacja -
Optimization of combined heat and power (CHP) market allocation: The case of Poland
PublikacjaCombined heat and power (CHP), that is production of electricity and useful heat in a single thermodynamic process, is a way of primary energy saving and emission reduction. Therefore, promotion of the electricity from high-efficiency cogeneration (CHP-E) was encouraged in the European Union. However, CHP-E promotion mechanisms proved low effectiveness in certain countries, like Poland, where the prices of certificates of origin...
-
Experiences from operation of various expansion devices in small scale ORC
PublikacjaThe main aim of this paper was to present various expansion devices for an application in the small scale ORC system. The investigations were carried out in two parallel directions. One direction was to design and construct a device dedicated to the analyzed ORC system. The second direction was to adapt existing expansion devices for the needs of the analyzed ORC system. Four various devices were described and presented together...
-
Jan Wajs dr hab. inż.
Osoby -
Experimental investigation of domestic gas boiler fitted with ORC module
PublikacjaIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Dariusz Mikielewicz prof. dr hab. inż.
OsobyDariusz Mikielewicz – urodził się 6 lutego 1967 roku w Gdańsku, w 1985r. zdał pomyślnie egzaminy wstępne na Wydział Budowy Maszyn Politechniki Gdańskiej, który ukończył z wynikiem bardzo dobrym w 1990 roku na specjalności Maszyny i Urządzenia Energetyczne. Zainteresowania pracą naukową skłoniły go do podjęcia badań na University of Manchester na wydziale mechanicznym i energetyki jądrowej (Mechanical and Nuclear Engineering Department)...
-
Bismuth-Doped Nano Zerovalent Iron: A Novel Catalyst for Chloramphenicol Degradation and Hydrogen Production
PublikacjaIn this study, we showed that doping bismuth (Bi) at the surface of Fe0 (Bi/Fe0, bimetallic iron system)—synthesized by a simple borohydride reduction method—can considerably accelerate the reductive degradation of chloramphenicol (CHP). At a reaction time of 12 min, 62, 68, 74, 95, and 82% degradation of CHP was achieved with Fe0, Bi/Fe0-1 [1% (w/w) of Bi], Bi/Fe0-3 [3% (w/w) of Bi], Bi/Fe0-5 [5% (w/w) of Bi], and Bi/Fe0-8 [8%...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublikacjaThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...
-
Theoretical Organic Rankine Cycle efficiency depending on different thermodynamic work variables.
PublikacjaOne of promising technologies of utilizing low- temperature waste heat is through ORC (Organic Rankine Cycle) system implementation. A primary objective in designing in-stallations based on such systems is to maximize the installation's work efficiency. On the other hand, ecological factors are commonly considered a natural barrier in introducing new, often very expensive technologies. Ecological effect of a potential modernization...
-
Small wood waste fired combined heat and power plant. Possible use of wood biomass for the generation of electric and heat energy as an alternative to fossil fuels
PublikacjaThis article discusses the possibility of burning wood biomass instead of fossil fuels in boilers. It describes the properties of wood biomass, including the variation of its calorific value depending on the moisture content of wood. The article proposes several variants of a combined heat and power plant (CHP) system burning wood biomass for the generation of electric and heat energy, using the energy contained in exhaust gases...
-
Intelligent microbearing project with memory of stress-strain history
PublikacjaTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Adapting the pinch point analysis to improve the ORC design process
PublikacjaPinch point analysis can be adapted so as to assist in the early stages of designing the ORC systems. Typically used in determining the working parameters of heat exchangers, it can be employed to improve the heat fitting between the source of heat and the working fluids of the ORC system. To attain the parametric match, an algorithm was built enabling quick estimation of the possible heat reception by the specific working fluid....
-
Nuclear Co-generation: The Analysis of Technical Capabilities and Cost Estimates
PublikacjaThis paper presents a concept of the parallel connection of a nuclear power plant fitted to provide heat for district heating application, with the CHP and heat plants existing in the supply region, in this case with the heating systems of Wejherowo and Gdynia. Presented variant proposes to add heat to a nuclear power plant’s total output by supplying heat exchangers with the steam from bleeders of low pressure (LP) turbine stage...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublikacjaThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
The Possibility to use a Nuclear Power Plant as a Source of Electrical Energy and Heat
PublikacjaIn this article issues concernig the possibility of nuclear power plant (NPP) operation also as a source of heat, which means combined heat and power production, have been described. CHP work is possible and profitable only in those areas where high thermal power demand occurs, which means near city agglomerations such as Warsaw or the Tri-City. Two levels of thermal power delivered to the heating system have been considered. Preliminary...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Experimental investigations of damage evolution in concrete during bending by continuous micro-CT scanning
PublikacjaThe paper describes experimental investigation results of fracture in notched concrete beams under quasi-static three-point bending. To visualize 3D fracture in concrete under bending, an extended X-ray micro-computed tomography system was used, i.e. the tomography system SkyScan 1173 was connected to the loading machine ISTRON 5569. This combined system enabled to shot images of deforming concrete beams during a continuous deformation...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Responsible Court in the Global World - Managerism or Managerialism
PublikacjaOne can look at the improvement of the effectiveness and efficiency of the justice system from three perspectives: macro, mezo, and micro. After all, the general goal is to enhance the effectiveness and efficiency of the justice system as a whole (the macro perspective), the courts (the mezo scale), and court proceedings (the micro scale). The need to improve the effectiveness and efficiency of the justice system was noticed in...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Impact of the glazed roof on acoustics of historic interiors
PublikacjaThe paper discusses the adverse acoustic phenomena occurring in the semi-open interiors (courtyards, yards) covered with a glass roof. Particularly negative is the rever-beration noise, which leads to the degradation of the utility functions of the resulting spaces. It involves the drastically reducing the intelligibility of speech, loss of natural sounding of music, problems with the sound system, as well as disturbances in the...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublikacjaThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
Innowacyjny moduł ultradźwiękowy systemu monitoringu technicznego mostu podwieszonego w Rzeszowie
PublikacjaW artykule przedstawiono system monitoringu technicznego konstrukcji mostu podwieszonego nad rzeką Wisłok. System będzie wyposażony w dodatkowy moduł ultradźwiękowy umożliwiający śledzenie degradacji mechanicznej betonu w pylonie mostu. Wczesne wykrywanie stref mikropęknięć, przed pojawieniem się widocznych rys, umożliwia monitorowanie amplitud propagującej fali ultradźwiękowej oraz analizę sygnałów w dziedzinie częstotliwości.
-
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublikacjaThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Pipeline System for Heat Transportation from Nuclear Power Plant – an Optimizing Approach
PublikacjaOver the last few years heat piping insulation technology and pump systems efficiency have been significantly improved. Reduced thermal losses encourage heat transportation over long distances. It provides an opportunity for increasing thermodynamic efficiency of Nuclear Power Plants (NPPs) that are often located in rural areas because of safety issues. It can be achieved by Combined Heat and Power (CHP) generation, as heat produced...
-
Prowadzenie ruchu małego źródła kogeneracji gazowej według kryterium efektu ekonomicznego
PublikacjaCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Prowadzenie ruchu małej elektrociepłowni gazowej według kryterium efektu ekonomicznego
PublikacjaCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Performance Characteristics of a Micro-turbine, International
Publikacja. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Performance Characteristics of a Micro-Turbine
PublikacjaIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
THE THERMODYNAMIC ANALYSIS OF THE SZEWALSKI HIERARCHIC VAPOUR CYCLE COOPERATED WITH THE SYSTEM OF HEAT RECOVERY
PublikacjaIn this paper, thermodynamic analysis of the Szewalski hierarchic vapour cycle cooperated with the system of heat recovery from exhaust gases are presented. According to that purpose, the CFM (Computation Flow Mechanics [1,3]) approach has correctly been used. The whole system consists of the first traditional steam cycle, the second organic Rankine cycle (ORC) and system of heat recovery with use of water with temperature 90...
-
Optical method for verification of homogeneity of phantoms for calibration of magnetic resonance
PublikacjaThe primary purpose of this study was to develop a laboratory photonic set-up for characterisation of homogeneity of gel phantoms for calibration of magnetic resonance. In this system, optical coherence tomography allows the detection of micro- and macroscopic heterogeneities of a structure. The set-up was used to perform measurements of agar and agar-carrageenan gels, which are the basis for more complex phantoms for magnetic...
-
Criteria for selection of working fluid in low-temperature ORC
PublikacjaThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Nonlinear Free and Forced Vibrations of a Hyperelastic Micro/Nanobeam Considering Strain Stiffening Effect
PublikacjaIn recent years, the static and dynamic response of micro/nanobeams made of hyperelasticity materials received great attention. In the majority of studies in this area, the strain-stiffing effect that plays a major role in many hyperelastic materials has not been investigated deeply. Moreover, the influence of the size effect and large rotation for such a beam that is important for the large deformation was not addressed. This...
-
From Scores to Predictions in Multi-Label Classification: Neural Thresholding Strategies
PublikacjaIn this paper, we propose a novel approach for obtaining predictions from per-class scores to improve the accuracy of multi-label classification systems. In a multi-label classification task, the expected output is a set of predicted labels per each testing sample. Typically, these predictions are calculated by implicit or explicit thresholding of per-class real-valued scores: classes with scores exceeding a given threshold value...
-
The system for identification of the band saw wheel cross profile
PublikacjaPrzedstawiono system do identyfikacji zarysu poprzecznego koła pilarki taśmowej, dzięki któremu producent pił taśmowych ma możliwość naprężenia brzeszczotu piły w sposób zapewniający jej poprawną pracę. Opisano budowę i zasadę działania systemu. Uzyskane dane mogą być wprowadzane do układów sterowania automatycznych urządzeń ze sterowaniem CNC (naprężających piły taśmowe). Dane systemu: szerokość sprawdzanych kół do 300 mm, dokładność...
-
Recovering Sound Produced by Wind Turbine Structures Employing Video Motion Magnification
PublikacjaThe recordings were made with a fast video camera and with a microphone. Using fast cameras allowed for observation of the micro vibrations of the object structure. Motion-magnified video recordings of wind turbines on a wind farm were made for the purpose of building a damage prediction system. An idea was to use video to recover sound & vibrations in order to obtain a contactless diagnostic method for wind turbines. The recovered signals...
-
Optoelectronic device for hematocrit measurements
PublikacjaAn optoelectronic system for measurements of hematocrit level (HCT) in the whole human blood is presented. Proposed system integrates a dedicated optoelectronic sensor, a microcontroller and a small LCD display in a low cost, battery-powered, handheld device. Chosen method for determining blood hematocrit level is based on optical properties of whole blood in visible and NIR wavelength range. Measurements with the use of proposed...