Wyszukiwarka
Filtry
wszystkich: 566
Wyniki wyszukiwania dla: FORCE FIELD
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Modified linear viscoelastic model of earthquake-induced structural pounding
PublikacjaIn recent times, earthquake-induced structural pounding has been intensively studied through the use of different impact force models. The numerical results obtained from the previous studies indicate that the linear viscoelastic model is relatively simple and accurate in modeling pounding-involved behavior of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just...
-
Damage-Involved Structural Pounding in Bridges under Seismic Excitation
PublikacjaDuring severe earthquakes, pounding between adjacent superstructure segments of highway elevated bridges was often observed. It is usually caused by the seismic wave propagation effect and may lead to significant damage. The aim of the present paper is to show the results of the numerical analysis focused on damage-involved pounding between neighbouring decks of an elevated bridge under seismic excitation. The analysis was carried...
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublikacjaThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
A New Rehabilitation Device for Balance Impaired Individuals
PublikacjaIn the paper authors present a device designed to improve the rehabilitation process of people with balance impairment. The discussed device (JStep) utilizes a commercially available static standing frame (stander) modified in order to fit force sensing units under the feet and in the pillows around the hips of a patient. While executing rehabilitation tasks, the patient may compensate his balance deficiency by leaning on the pillows...
-
Homogeneous nucleation rate of methane hydrate formation under experimental conditions from seeding simulations
PublikacjaIn this work, we shall estimate via computer simulations the homogeneous nucleation rate for the methane hydrate at 400 bars for a supercooling of about 35 K. The TIP4P/ICE model and a Lennard-Jones center were used for water and methane, respectively. To estimate the nucleation rate, the seeding technique was employed. Clusters of the methane hydrate of different sizes were inserted into the aqueous phase of a two-phase gas–liquid...
-
Optimum number of actuators to minimize the cross-sectional area of prestressable cable and truss structures
PublikacjaThis paper describes a new computational method for determining the optimum number of actuators to design the optimal and economic cross-sectional area of pin-jointed assemblies based on the conventional force method. The most active members are selected to be prestressed to redistribute stress in the whole structure, resulting in regulating the internal force of bars that face high stress. Reducing stress in critical members allows...
-
Investigation method of large-volume tire with mobile test rig
PublikacjaThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Investigation of the thrust generated by active isolated hydrofoils via wave-induced ship motion
PublikacjaWave Augmented Hydrofoil Technology (WAHT) aims to convert hydrofoil movement, induced by ship motion, into thrust force, and ship's resistance reduction in waves. Despite the growing interest in WAHT, a significant research gap remains in understanding the complex interactions between hydrofoil design parameters and wave-induced thrust generation. A hydrofoil attached to a ship serves dual roles; reducing the ship resistance in...
-
Stability of trusses with linear elastic side-supports
PublikacjaThe present research is devoted to study of a lateral buckling of truss with linear elastic side supports. The elastic support reaction in relation to force in compressed chord and coefficient of buckling length related to side support distance are also calculated. The effect of slope of side support on limit force is also considered. The nonlinear analysis of two roof trusses are carried out. The results are compared to design...
-
The impact of ICTs on women’s economic empowerment
PublikacjaIt is widely argued that ICTs enable the inclusion of low-skilled and traditionally marginalized groups, such as women, people with disabilities, and workers at the base of the pyramid (BoP), in the labor market. In this paper, we investigate the determinants of female participation in the labor market in developing countries with a focus on the impact of the use of ICTs on female labor force participation. We conduct a panel study...
-
The Impact of ICTs on Women’s Economic Empowerment
PublikacjaIt is widely argued that ICTs enable the inclusion of low-skilled and traditionally marginalized groups, such as women, people with disabilities, and workers at the base of the pyramid (BoP), in the labor market. In this paper, we investigate the determinants of female participation in the labor market in developing countries with a focus on the impact of the use of ICTs on female labor force participation. We conduct a panel study...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublikacjaThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
A non-linear direct peridynamics plate theory
PublikacjaIn this paper a direct non-local peridynamics theory for thin plates is developed. Peridynamic points are assumed to behave like rigid bodies with independent translation and finite rotation degrees of freedom. The non-local mechanical interaction between points is characterized by force and moment vectors. The balance equations including the linear momentum, the angular momentum and the energy are presented. Peridynamic deformation...
-
Analysis of the relationship between cutting forces and local structural properties of Scots pine wood aided by computed tomography
PublikacjaX-ray computed tomography (CT) is utilised in some sawmills today, primarily for enhancing value yield and for process automation, which includes log sorting and sawing optimisation. Nevertheless, there is a scarcity of recent research utilising CT to assess the local cutting process. As a preliminary study, this paper addresses this gap by using CT to investigate the connections between local cutting force and local wood properties...
-
Nonlinear planar modeling of massive taut strings travelled by a force-driven point-mass
PublikacjaThe planar response of horizontal massive taut strings, travelled by a heavy point-mass, either driven by an assigned force, or moving with an assigned law, is studied. A kinematically exact model is derived for the free boundary problem via a variational approach, accounting for the singularity in the slope of the deflected string. Reactive forces exchanged between the point-mass and the string are taken into account via Lagrange...
-
Wyznaczenie obciążeń na poszycie okrętu wywołanych uderzeniem fal i uderzeniem w lód i ich wpływ na bezpieczeństwo okrętu
PublikacjaThe main problem is the vessels rather accurate determination of the hydrodynamic loads so-called hydroelasticity outside . This can be done by theoretical analysis , computer simulation or by experiment. This gives the hydrodynamic pressure distribution on the walls of the ship's hull and also on the walls of marine vessels .The most dangerous are the impact of extreme storm waves , the impact of the wharf and the impact zone...
-
Focused ion beam-based microfabrication of boron-doped diamond single-crystal tip cantilevers for electrical and mechanical scanning probe microscopy
PublikacjaIn this paper, the fabrication process and electromechanical properties of novel atomic force microscopy probes utilising single-crystal boron-doped diamond are presented. The developed probes integrate scanning tips made of chemical vapour deposition-grown, freestanding diamond foil. The fabrication procedure was performed using nanomanipulation techniques combined with scanning electron microscopy and focused ion beam technologies....
-
A comparative analysis of numerically simulated and experimentally measured static responses of a floating dock
PublikacjaTwo numerical methods, dynamic and static analyses, are proposed to calculate the static responses of a floating dock under different ballast water distributions. Model-scale experimental tests were conducted to compare with these numerical methods. The dynamic analysis includes a 6-degree-of-freedom (6-DOF) model, a hydrostatic force model and a hydrodynamic force model to simulate the dock's freely floating processes. The dock's...
-
Towards hand grip force assessment by using EMG estimators
PublikacjaThe purpose of this study was to propose a method to assess individual regression (calibration) curves to establish a relationship between an isometric grip force and surface electromyography (EMG) estimator. In this study 18 healthy volunteers (12 male (23.0 ± 2.0 years) and 6 female (23.2 ± 0.7 years)) had been examined. Ten EMG estimators (mean absolute value, root mean square, entropy, energy, turns per second, mean of zero...
-
CENTRAL-FORCE DECOMPOSITION OF THE TERSOFF POTENTIAL
PublikacjaCentral forces play important role in the analysis of results obtained with particle simulation methods, since they allow evaluating stress fields. In this work we derive expressions for a central-force decompositon of the Tersoff potential, which is often used to describe interatomic interactions in covalently bonded materials. We simplify the obtained expressions and discuss their properties.
-
Linear viscoelastic modelling of damage-involved structural pounding during earthquakes
PublikacjaDamage-involved structural pounding during earthquakes has been recently intensively studied using different impact force models. The results of the previous studies indicate that the linear viscoelastic model is relatively simple yet accurate in modelling pounding-involved behaviour of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just before separation, which...
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublikacjaThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublikacjaResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
Design and Evaluation of the Platform for Weight-Shifting Exercises with Compensatory Forces Monitoring
PublikacjaDetails of a platform for the rehabilitation of people with severe balance impairment are discussed in the paper. Based upon a commercially available static parapodium, modified to fit force sensors, this device is designed to give a new, safe tool to physiotherapists. It is designed for the patients who cannot maintain equilibrium during a bipedal stance and need to hold to or lean on something during the rehabilitation. Visual,...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublikacjaThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Development of a Friction Welding System for CNC Lathes
PublikacjaDedicated friction welding machines are sturdy in order to handle large process forces but expensive. Thus, it is proposed to equip two axis CNC lathes with an add-on direct drive friction welding system as an affordable solution for occasional use. The first part to be welded is clamped on the lathe chuck, whilst the second part is clamped on a dedicated chuck on the tailstock. The latter is programmed to follow three phases:...
-
Comparison of non-linear statical analysis of truss with linear and rotational side supports and 3d roof model
PublikacjaIn the paper geometrically non-linear analysis of example truss with linear and rotational elastic side supports is compared with geometrically non-linear analysis of part of the roof construction with purlins and truss-bracing. For different stiffness of side-supports a non linear relation between normal force in compressed chord due to out of truss plane displacement has been calculated.
-
Homoclinics for singular strong force Lagrangian systems
PublikacjaWe study the existence of homoclinic solutions for a class of generalized Lagrangian systems in the plane, with a C1-smooth potential with a single well of infinite depth at a point ξ and a unique strict global maximum 0 at the origin.Under a strong force condition around the singular point ξ, via minimization of an action integral, we will prove the existence of at least two geometrically distinct homoclinic solutions.
-
Influence of meniscus shape in the cross sectional plane on the knee contact mechanics
PublikacjaWe present a three dimensional finite element analysis of stress distribution and menisci deformation in the human knee joint. The study is based on the Open Knee model with the geometry of the lateral meniscus which shows some degenerative disorders. The nonlinear analysis of the knee joint under compressive axial load is performed. We present results for intact knee, knee with partial and complete radial posterior meniscus root...
-
Numerical study on pounding between two adjacent buildings under earthquake excitation
PublikacjaSeismic excitation, which results in large horizontal relative displacements, may cause collisions between two adjacent structures due to insufficient separation distance between them. Such collisions, known as earthquake-induced structural pounding, may induce severe damages. In this paper, the case of pounding between two adjacent buildings is studied by the application of single degree-of-freedom structural models. Impact is...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Homoclinic orbits for a class of singular second order Hamiltonian systems in ℝ3
PublikacjaWe consider a conservative second order Hamiltonian system \ddot{q}+ ∇V(q)=0 in R3 with a potential V having a global maximum at the origin and a line l ∩ {0} = ∅ as a set of singular points. Under a certain compactness condition on V at infinity and a strong force condition at singular points we study, by the use of variational methods and geometrical arguments, the existence of homoclinic solutions of the system.
-
The Point Estimate Method in a Reticulated Shell Reliability Analysis
PublikacjaThe objective of this paper is to present an application of the point estimate method (PEM) to determine the probabilistic moments for engineering structures. Reliability analysis is illustrated by two examples: an estimation of the critical force in linear elastic buckling analysis and a reticulated shell limit load determinations. Calculations were also made using Monte Carlo method. It has been shown the practical usefulness...
-
Numerical and Clinical Analysis of an Eyeball Injuries under Direc Impact
PublikacjaObjectives: The objective of this study was to develop a numerical model of the eyeball and orbit to simulate a blunt injury to the eyeball leading to its rupture, as well as to conduct a comparative analysis of the results obtained using the finite element method against the clinical material concerning patients who had suffered an eyeball rupture due to a blunt force trauma. Material and Methods: Using available sclera biometric and...
-
Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding
PublikacjaStructural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various...
-
Advanced seismic control strategies for smart base isolation buildings utilizing active tendon and MR dampers
PublikacjaThis paper investigates the seismic behaviour of a five-storey shear building that incorporates a base isolation system. Initially, the study considers passive base isolation and employs a multi-objective archived-based whale optimization algorithm called MAWOA to optimize the parameters of base isolation. Subsequently, a novel model is proposed, which incorporates an interval type-2 Takagi-Sugeno fuzzy logic controller (IT2TSFLC)...
-
Two families of infinitely many homoclinics for singular strong force Hamiltonian systems
PublikacjaWe are concerned with a planar autonomous Hamiltonian system with a potential possessing a single well of infinite depth at a point X and a unique strict global maximum 0 at a point A. Under a strong force condition around the singularity X, via minimization of an action integral and using a shadowing chain lemma together with simple geometrical arguments, we prove the existence of infinitely many geometrically distinct homoclinic...
-
Ferromagnetic nanocrystallites in the SiO2 - PbO - Fe2O3 glass system
PublikacjaThe structure of 50% SiO2 - 35% PbO - 15% Fe2O3, 50% SiO2 - 30% PbO - 20% Fe2O3 and 50% SiO2 - 25% PbO - 25% Fe2O3 (in mol%) glass was investigated by the means of AFM microscopy and X-ray diffraction. Observation by the atomic force microscopy shows that each of prepared iron oxide glass doesn't have homogeneous structure and some nanocrystallites were detected. Next, test with neodymium magnet found out strong magnetic properties...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublikacjaThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Investigation of the Effect of the Rocket's Suborbital Flight on Biofilm, Enzymes and Biosynthesis on Autonomous, Modular and Scalable Platforms For Conducting Experiments of an Astrobiotechnological Nature
PublikacjaWith new incentives for human space exploration, biotechnological experiments in orbit became imperative. Answering this need, we build an autonomous, modular, and scalable platform that enables those experiments on rockets. We called it AMBER. The aim of the payload of the R6 suborbital rocket is to perform an experiment to study the influence of rocket flights on biofilm, molecular biology enzymes and biosynthesis using our platform....
-
MODELLING OF CUTTING BY MEANS OF FRACTURE MECHANICS
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
Modelling of cutting by means of fracture mechanics
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublikacjaThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
Mechanical Properties of Human Stomach Tissue
PublikacjaThe dataset entitled Determination of mechanical properties of human stomach tissues subjected to uniaxial stretching contains: the length of the sample as a function of the corresponding load (tensile force) and the initial values of the average width and average thickness of the sample. All tests were conducted in a self-developed tensile test machine: PG TissueTester. The dataset allows the coefficients of various models of...
-
Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study
PublikacjaPurpose This study aimed to investigate the geometrical and mechanical properties of human thoracic spine ligaments subjected to uniaxial quasi-static tensile test. Methods Four human thoracic spines, obtained through a body donation program, were utilized for the study. The anterior longitudinal ligament (ALL), posterior longitudinal ligament (PLL), capsular ligament (CL), ligamenta flava (LF), and the interspinous ligament and...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublikacjaIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...