Filtry
wszystkich: 332
-
Katalog
Wyniki wyszukiwania dla: KANBAN SCHEDULE BOARD
-
STRUCTURE AND ALGORITHMS OF A DIAGNOSTIC DEVICE IN A WHEELED TRACTOR
PublikacjaDiagnostic device monitors the tractor’s technical condition and identifies the location of damaged components during operation. The diagnostic device detects and identifies the following types of defects: functional defects (uf) which affect performance, exhaust defects (ue) which increase toxic emissions and fuel consumption, defects that jeopardize driving safety (us), defects that affect engine performance (ud). The key component...
-
Feasibility Study GaN Transistors Application in the Novel Split-Coils Inductive Power Transfer System with T-Type Inverter
PublikacjaA promising solution for inductive power transfer and wireless charging is presented on the basis of a single-phase three-level T-type Neutral Point Clamped GaN-based inverter with two coupled transmitting coils. The article focuses on the feasibility study of GaN transistor application in the wireless power transfer system based on the T-type inverter on the primary side. An analysis of power losses in the main components of the...
-
Low cost real time UAV stereo photogrammetry modelling technique – accuracy considerations
PublikacjaThe paper presents accuracy considerations regarding three 3D modelling techniques. The tested new consumer type stereo camera (ZED 3D Stereolabs) has been implemented info an aerial mapping system, on board micro air vehicle MAV) and tested object has been mapped using a real-time photogrammetry with original real-time software application. The evaluated results has been compared with model gained with a state of art unmanned...
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublikacjaThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Detection of Anomalies in the Operation of a Road Lighting System Based on Data from Smart Electricity Meters
PublikacjaSmart meters in road lighting systems create new opportunities for automatic diagnostics of undesirable phenomena such as lamp failures, schedule deviations, or energy theft from the power grid. Such a solution fits into the smart cities concept, where an adaptive lighting system creates new challenges with respect to the monitoring function. This article presents research results indicating the practical feasibility of real‐time...
-
Jacek Stefański prof. dr hab. inż.
OsobyJacek Stefański ukończył studia na Wydziale Elektroniki Politechniki Gdańskiej (PG) w 1993 r. W 2000 r. uzyskał stopień doktora nauk technicznych w dyscyplinie telekomunikacja, w 2012 r. stopień doktora habilitowanego, natomiast w 2020 r. tytuł profesora nauk inżynieryjno-technicznych. Obecnie pracuje na stanowisku profesora w Katedrze Systemów i Sieci Radiokomunikacyjnych (KSiSR) PG. W latach 2005-2009 był zatrudniony w Instytucie...
-
Józef Woźniak prof. dr hab. inż.
OsobyProf. dr hab. inż. Józef Woźniak prof. zw. Politechniki Gdańskiej ukończył studia na Wydziale Elektroniki Politechniki Gdańskiej w 1971 r. W 1976 r. uzyskał stopień doktora nauk technicznych, a w 1991 r. stopień doktora habilitowanego w dyscyplinie telekomunikacja i specjalności teleinformatyka. W styczniu roku 2002 otrzymał tytuł profesora nauk technicznych. W 1994 r. został mianowany na stanowisko profesora nadzwyczajnego w Politechnice...
-
Challenges associated with development of AUV - unmanned autonomous underwater vehicles to be operated using the AI-based control systems
PublikacjaThe last decade has been devoted towards further development of the UUV unmanned underwater vehicles which may be of two types. There are the USV unmanned surface vehicles and UUV unmanned underwater vehicles. There is a growing interest to work out and implement the fully advanced AUV autonomous underwater vehicles. The main drivers towards development of such the vehicles are the technologies of autonomous systems, sensors and...
-
Układ informatyczny systemu diagnostycznego ciągników kołowych
PublikacjaPodstawowym elementem systemu diagnostycznego jest komputer pokładowy Fujitsu FUTRO S100 z chłodzeniem pasywnym w wykonaniu odpornym na drgania i wstrząsy, z pamięcią Compact Flesh 16Gb. Do komputera dołączony jest monitor dotykowy NVOX LCD 10" VGA/FVAT. Oprogramowanie komputera obejmuje system operacyjny Windows XP-2000, driver konwertera USB/DeviceNet oraz opracowany program diagnostyczny. Komputer połączony jest łączem USB z...
-
Images of the Seabed of the Gulf of Gdansk Obtained by Means of the Parametric Sonar
PublikacjaThe main goal of this paper is to present results of the experimental investigation of the seabed by means of parametric echosounder in the form of chosen images. The phenomena of nonlinear interaction between two parallel beams of high intensity gives as a results very narrow beam of low frequency wave, that enables to penetrate the sea bottom. The first step of our investigations was calibration of all the elements of the measuring...
-
COLREGS compliance in Evolutionary Sets of Cooperating Ship Trajectories
PublikacjaIn general, Evolutionary Sets of Cooperating Ship Trajectories combine some of the assumptions of game theory with evolutionary programming and aim to find optimal set of cooperating trajectoriesof all ships involved in an encounter situation. In a two-ship encounter situation the method enables the operator of an on-board collision-avoidance system to predict the most probable behaviour of atarget and to plan the own manoeuvres...
-
Towards Improving Optimised Ship Weather Routing
PublikacjaThe aim of the paper is to outline a project focusing on the development of a new type of ship weather routing solution with improved uncertainty handling, through better estimation of ship performance and responses to sea conditions. Ensemble forecasting is considered to take into account the uncertainty levels that are typical of operations in a stochastic environment. Increased accuracy of weather prediction is achieved through...
-
Dataset Related Experimental Investigation of Chess Position Evaluation Using a Deep Neural Network
PublikacjaThe idea of training Articial Neural Networks to evaluate chess positions has been widely explored in the last ten years. In this paper we investigated dataset impact on chess position evaluation. We created two datasets with over 1.6 million unique chess positions each. In one of those we also included randomly generated positions resulting from consideration of potentially unpredictable chess moves. Each position was evaluated...
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublikacjaIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Scheduling with Complete Multipartite Incompatibility Graph on Parallel Machines
PublikacjaIn this paper we consider a problem of job scheduling on parallel machines with a presence of incompatibilities between jobs. The incompatibility relation can be modeled as a complete multipartite graph in which each edge denotes a pair of jobs that cannot be scheduled on the same machine. Our research stems from the works of Bodlaender, Jansen, and Woeginger (1994) and Bodlaender and Jansen (1993). In particular, we pursue the...
-
Paweł Możejko dr hab.
Osoby -
Adrian Bekasiewicz dr hab. inż.
OsobyAdrian Bekasiewicz received the MSc, PhD, and DSc degrees in electronic engineering from Gdansk University of Technology, Poland, in 2011, 2016, and 2020, respectively. In 2014, he joined Engineering Optimization & Modeling Center where he held a Research Associate and a Postdoctoral Fellow positions, respectively. Currently, he is an Associate Professor with Gdansk University of Technology, Poland. His research interests include...
-
ALGORYTMY STEROWANIA SILNIKA WYSOKOPRĘŻNEGO Z UKŁADEM COMMON RAIL
PublikacjaRozwój wiedzy i technologii związanej z procesami spalania paliwa w silniku i prowadzeniem kontrolowanego procesu spalania, skutkuje wzrostem sprawności silników i lepszą ochroną środowiska. Ciekawym rozwiązaniem technicznym jest silnik z zapłonem samoczynnym pracujący z bardzo wysokim ciśnieniem wtrysku paliwa i często z recyrkulacją spalin – silnik z układem Common Rail. Do sterowania silnika stosowane są złożone układy mechatroniczne...
-
Sprzętowa implementacja transformacji Hougha w czasie rzeczywistym
PublikacjaW artykule przedstawiono implementację sprzętową w FPGA algorytmu do wykrywania kształtów aproksymowanych zbiorem linii prostych podczas przetwarzania obrazu cyfrowego w czasie rzeczywistym. W opracowanej strukturze sprzętowej podniesiono efektywność przetwarzania poprzez zastosowanie przetwarzania przepływowego, lookup table, wykorzystanie wyłącznie arytmetyki liczb całkowitych oraz rozproszenie pamięci głosowania. Eksperymentalnie...
-
PRINCIPLES OF ARTIFICIAL INTELLIGENCE APPLICATION IN CONTROL OF THE ENTERPRISE
PublikacjaThe implementation of the tasks of evaluating historical financial information, the control or audit of business activities are based primarily on professional judgments about the object of study of a professional accountant or auditor. Their findings are drawn on the basis of the study of documents, the use of audit evidence, risk assessment, etc. There is always a probability (and rather high) that professional judgment will...
-
Krzysztof Wach prof. dr hab.
Osoby -
Evolutionary Planning of Safe Ship Tracks in Restricted Visibility
PublikacjaThe paper presents the continuation of the author's research on ship track planning by means of Evolutionary Algorithms (EA). The presented method uses EA to search for an optimal set of safe tracks for all ships involved in an encounter. Until now the method assumed good visibility – compliance with standard rules of the Convention on the International Regulations for Preventing Collisions at Sea (COLREGS, 1972). However, in restricted...
-
Analysis of the Possibilities of Applying 3D Print Methods for the Needs of Ship-Building Industry
PublikacjaArticle presents the analysis of applying additive and hybrid manufacturing methods and its impact on dynamic stiffness of prepared samples. Dynamic analysis of the handle bracket specimens consisted in plotting the resonance curves and using these curves to estimate the dynamic stiffness of elements produced with additive manufacturing technology. Authors focused especially on 3D print in Fused Deposiotion Modeling/Fused Filament...
-
STEROWANIE RAMIENIEM ROBOTA Z WYKORZYSTANIEM DANYCH Z KAMERY CYFROWEJ I MECHANIZMÓW SZTUCZNEJ INTELIGENCJI
PublikacjaPierwotnym zamysłem zespołu było stworzenie uniwersalnego systemu grającego w gry planszowe. Mierząc się z tym problemem, postanowiono zrobić jednak coś więcej - wywrócić dotychczasową koncepcję pracy użytkownika z komputerem „do góry nogami” i nie zmuszać użytkownika do nauki interfejsu, a zmusić system do współpracy z interfejsem, który rozumie użytkownik. Dokonane zostało więc przejście ze świata wirtualnego do świata rzeczywistego...
-
Damage Control in Warships
PublikacjaAs a result of dynamic quantitative and qualitative developments in the maritime industry its participants face harder and harder challenges pertaining to safety of ships and navigation. Practice has shown that even very well organised fleets are harassed by emergencies and accidents that can be neither predicted nor absolutely avoided. In order to counter the occuring emergencies and accidents, and to minimize their effects damage...
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublikacjaCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
Prediction of Ship Resonant Rolling - Related Dangerous Zones with Regard to the Equivalent Metacentric Height Governing Natural Frequency of Roll
PublikacjaPotentially dangerous zones corresponding to dynamical stability phenomena, possibly encountered by ships sailing in rough sea, are estimated nowadays with the use of the method recommended by IMO in the guidance coded MSC.1/Circ.1228. In this IMO method the parameter governing the natural period of roll is the initial metacentric height. Some earlier studies revealed that the initial metacentric height...
-
Towards Precise Visual Navigation and Direct Georeferencing for MAV Using ORB-SLAM2
PublikacjaA low accuracy of positioning using Global Navigation Satellite System (GNSS) are not meet geodetic requirements for direct images georeferencing for Unmanned Aerial Vehicle (UAV) photogrammetry. A majority of UAVs are equipped with a monocular or stereo non-metric cameras for either visual data gathering or live video feed for operator. A cheap positioning techniques used on board commercial UAVs are not that precise as geodetic...
-
Size effect in concrete under splitting tension
PublikacjaThe size effect is a fundamental phenomenon in concrete materials. It denotes that both the nominal structural strength and material ductility always decrease with increasing element size under tension. In the paper splitting tensile tests on cylindrical concrete specimens with the different diameter were carried out. Two types of the loading strip (plywood board and steel cylinder) were used. The concrete strength and ductility...
-
Józef Judycki prof. dr hab. inż.
Osoby -
Waldemar Kamrat prof. dr hab. inż.
Osoby -
Metodyczne aspekty projektowania systemów zarządzania zmianą. Procesy planistyczno-sterujące produkcją w zarządzaniu operacyjnym
PublikacjaNiniejsza monografia dotyczy problematyki zaawansowanych systemów produkcyjnych, a w szczególności zagadnień zarządzania zmianą w obszarze procesów planistyczno-sterujących. Przez zaawansowane systemy produkcyjne w niniejszej monografii rozumiane są elastyczne systemy produkcyjne FMS (Flexible Manufacturing System) oraz dalsze systemy wynikające z ich doskonalenia i rozwoju (warunkowanego przede wszysztkim technologiami informacyjnymi...
-
Laboratory Load Model Based on 150 kVA Power Frequency Converter and Simulink Real-Time – Concept, mplementation, Experiments
PublikacjaFirst section of the paper provides technical specification of laboratory load model basing on 150 kVA power frequency converter and Simulink Real-Time platform. Assumptions, as well as control algorithm structure is presented. Theoretical considerations based on criteria which load types may be simulated using discussed laboratory setup, are described. As described model contains transformer with thyristor-controlled tap changer,...
-
Scheduling on Uniform and Unrelated Machines with Bipartite Incompatibility Graphs
PublikacjaThe problem of scheduling jobs on parallel machines under an incompatibility relation is considered in this paper. In this model, a binary relation between jobs is given and no two jobs that are in the relation can be scheduled on the same machine. We consider job scheduling under the incompatibility relation modeled by a bipartite graph, under the makespan optimality criterion, on uniform and unrelated machines. Unrelated machines...
-
Julita Wasilczuk dr hab.
OsobyUrodzona 5 kwietnia 1965 roku w Gdańsku. W latach 1987–1991 odbyła studia na Wydziale Ekonomiki Transportu Uniwersytetu Gdańskiego (obecnie Wydział Ekonomii). Od 1993 roku zatrudniona na nowo utworzonym Wydziale Zarządzania i Ekonomii, Politechniki Gdańskiej, na stanowisku asystenta. W 1997 roku uzyskała stopień doktora nauk ekonomicznych na WZiE, a w 2006 doktora habilitowanego nauk ekonomicznych w dyscyplinie nauki o zarządzaniu,...
-
Spotkanie informacyjne dla kandydatów do Szkoły Doktorskiej
WydarzeniaW dniu 29 czerwca, o godz. 11:00 (UTC+2) , odbędzie się spotkanie informacyjne dla kandydatów, dotyczące rekrutacji do Szkoły Doktorskiej PG na r.a. 2021/2022. Dostęp na hasło: PhD
-
Bariery stosowania technologii odzysku energii w transporcie szynowym
PublikacjaNa wstępie artykułu został przedstawiony przegląd istniejących technologii odzysku energii w procesie hamowania oraz możliwości jej wykorzystania. Omówiono możliwości akumulowania rekuperowanej energii w zasobnikach stacjonarnych oraz tych zainstalowanych w pojazdach, możliwość przesyłu energii do krajowej sieci energetycznej jak również jej bezpośredniego wykorzystania przez inne pojazdy znajdujące się na sieci. W części zasadniczej...
-
Ewolucyjne planowanie bezpiecznych trajektorii statków oparte na zmodyfikowanym diagramie Cockcrofta.
PublikacjaArtykuł przedstawia kontynuację badań autora nad planowaniem bezpiecznych trajektorii statków za pomocą algorytmów ewolucyjnych. Prezentowana metoda poszukuje optymalnego zbioru bezpiecznych trajektorii wszystkich statków biorących udział w spotkaniu. Bieżąca wersja metody zakłada ograniczoną widoczność i obowiązywanie Prawidła 19 Międzynarodowych Przepisów o Zapobieganiu Zderzeniom na Morzu (MPZZM) zamiast Prawideł 11 – 18. Artykuł...
-
Metody wykorzystania energii z rekuperacji w transporcie szynowym
PublikacjaW artykule przedstawiony został przegląd metod wykorzystania energii pochodzącej z hamowania odzyskowego. Wśród znanych i stosowanych w praktyce metod wymieniono wykorzystanie odzyskanej energii na nietrakcyjne potrzeby własne pojazdu, magazynowanie odzyskanej energii w zasobnikach (pokładowych lub stacjonarnych) i wykorzystywanie jej w razie potrzeby, transformację i zwrot odzyskanej energii do krajowej sieci zasilania, a także...
-
Podstawy zarządzania produkcją i usługami, W, ZiIP, sem 01, zimowy 22/23 (PG_00055043)
Kursy OnlineIstota zarządzania produkcją i usługami. Produkt i jego projektowanie, jakość, niezawodność, konstrukcja, prognozowanie popytu. Pojęcie systemu produkcyjnego. Struktura, formy organizacji i zarządzania systemami. Proces produkcyjny, rozmieszczenie urządzeń produkcyjnych, sterowanie przepływem produkcji (metody symulacyjne i analityczne). Projektowanie systemów produkcyjnych, sterowanie produkcją i realizacja usług. Planowanie potrzeb...
-
Optymalizacja rozkładu jazdy na kolei z uwzględnieniem efektywności hamowania odzyskowego.
PublikacjaNa wstępie artykułu przybliżono czytelnikowi, czym jest rozkład jazdy na sieci kolejowej, na czym polega jego optymalizacja oraz odwołano się do literatury opisującej proces jego konstrukcji. W dalszej części przedstawiono kryteria optymalizacji rozkładu jazdy i zaproponowano podejście od strony efektywności wykorzystania energii pochodzącej z hamowania rekuperacyjnego, realizowanego metodą odzysku bezpośrednio do sieci trakcyjnej....
-
IATUL Fall Seminar - Connecting in a disconnected world.
Wydarzenia We invite both current community members and other people interested in IATUL's activities to the online seminar on December 15, 2021. During the meeting, we will talk about the mission and activities of the organisation, as well as the benefits of belonging to the IATUL community. In addition, Special Interest Groups (SIGs), analysing...
-
A memory efficient and fast sparse matrix vector product on a Gpu
PublikacjaThis paper proposes a new sparse matrix storage format which allows an efficient implementation of a sparse matrix vector product on a Fermi Graphics Processing Unit (GPU). Unlike previous formats it has both low memory footprint and good throughput. The new format, which we call Sliced ELLR-T has been designed specifically for accelerating the iterative solution of a large sparse and complex-valued system of linear equations arising...
-
SYNTHESIZING MEDICAL TERMS – QUALITY AND NATURALNESS OF THE DEEP TEXT-TO-SPEECH ALGORITHM
PublikacjaThe main purpose of this study is to develop a deep text-to-speech (TTS) algorithm designated for an embedded system device. First, a critical literature review of state-of-the-art speech synthesis deep models is provided. The algorithm implementation covers both hardware and algorithmic solutions. The algorithm is designed for use with the Raspberry Pi 4 board. 80 synthesized sentences were prepared based on medical and everyday...
-
Portable exhaled breath analyzer employing fluctuation-enhanced gas sensing method in resistive gas sensors
PublikacjaThis paper presents a portable exhaled breath analyser, developed to detect selected diseases. The set-up employs resistive gas sensors: commercial MEMS sensors and prototype gas sensors made of WO3 gas sensing layers doped with various metal ingredients. The set-up can modulate the gas sensors by applying UV light to induce physical changes of the gas sensing layers. The sensors are placed in a tiny gas chamber of a volume...
-
The contactless method of chip-to-chip high-speed data transmission monitoring
PublikacjaThis paper presents a technique of decoupling differential signals transmitted in a pair of microstrip lines on a printed circuit board (PCB), using dedicated coupler for high speed data transmission monitoring in chip-to-chip interconnections. The coupler used for signal probing is overlayed on the pair of microstrip lines under test, and provides a signal to the next blocks of the measurement system without disturbing transmission...
-
Analysis of Validation and Simplification of Timber-Frame Structure Design Stage with PU-Foam Insulation
PublikacjaThe transition from experimental studies to the realm of numerical simulations is often necessary for further studies, but very difficult at the same time. This is especially the case for extended seismic analysis and earthquake-resistant design. This paper describes an approach to moving from the experimental testing of an elementary part of a wood-frame building structure to a numerical model, with the use of a commercial engineering...
-
Satish Raina prof. dr
Osoby -
Machine Learning Assisted Interactive Multi-objectives Optimization Framework: A Proposed Formulation and Method for Overtime Planning in Software Development Projects
PublikacjaMachine Learning Assisted Interactive Multi-objectives Optimization Framework: A Proposed Formulation and Method for Overtime Planning in Software Development Projects Hammed A. Mojeed & Rafal Szlapczynski Conference paper First Online: 14 September 2023 161 Accesses Part of the Lecture Notes in Computer Science book series (LNAI,volume 14125) Abstract Software development project requires proper planning to mitigate risk and...
-
Analysis of energy efficiency of suburban railway transport network
PublikacjaRising numbers of agglomeration residents cause increased need for people movement on daily basis. Because of congestion of local roads, air pollution and limited parking space, providing mass transit based on electric traction is reasonable. While the electric rail vehicles are considered highly efficient in themselves, they need to be analyzed as a part of a transport network, because energy consumption depends on operating conditions...