Filtry
wszystkich: 3832
-
Katalog
- Publikacje 2497 wyników po odfiltrowaniu
- Czasopisma 42 wyników po odfiltrowaniu
- Konferencje 8 wyników po odfiltrowaniu
- Osoby 41 wyników po odfiltrowaniu
- Projekty 2 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Kursy Online 22 wyników po odfiltrowaniu
- Dane Badawcze 1219 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MULTISINE MEASUREMENT SIGNALS
-
Generalized adaptive notch smoothers for real-valued signals and systems
PublikacjaSystems with quasi-periodically varying coefficients can be tracked using the algorithms known as generalized adaptive notch filters (GANFs). GANF algorithms can be considered an extension, to the system case, of classical adaptive notch filters (ANFs). We show that estimation accuracy of the existing algorithms, as well as their robustness to the choice of design parameters, can be considerably improved by means of compensating...
-
Determination of the tram track axis using a multi receiver GNSS measurement system
PublikacjaThis article refers to research, that has been conducted by an interdisciplinary research team from the Gdańsk University of Technology and the Maritime University in Gdynia since 2009. These investigation concerns the determination of a railway track axis using the mobile satellite measurement technique. Following the dynamic development of GNSS techniques, that could be seen in the last decade, the team carried out further experiments...
-
Ellipse-fitting algorithm implementation in the impedance measurement system based on DAQ card with FPGA
PublikacjaThe paper presents an implementation of the ellipse-fitting algorithm in the impedance measurement system based on DAQ card equipped with FPGA chip. The method implementation was tested by simulation means as well as experimentally in the designed and presented measurement system. Finally, the limit values of sampling parameters which assures satisfying accuracy were given.
-
Determination of the uncertainty of mass flow measurement using the orifice for different values of the Reynolds number
PublikacjaStandard orifice flowmeters are widely used in the chemical and energy industry. Therefore, it is essential to know how accurate the measurements made with these instruments are. The paper presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. The authors will present the influence of ranges of the Reynolds number on the estimated uncertainty, obtained on the basis of simulation and laboratory...
-
Broadening the scope of measurement and analysis of vibrations of an organ pipe employing intensity probe, simulations, and highspeed camera
PublikacjaThis paper shows an integrated approach to measure, analyze, and model phenomena occurring in an organ pipe driven by pressurized air. The aim of this paper is two-fold, i.e., to measure the pressure signal and the intensity field around the mouth by means of an intensity probe and to visualize and observe the motion of the air jet, which represents the excitation mechanism of the system. This is realized through two techniques,...
-
A Thermographic Measurement Approach to Assess Supercapacitor Electrical Performances
PublikacjaThis paper describes a proposal for the qualitative assessment of condition of supercapacitors based on the conducted thermographic measurements. The presented measurement stand was accompanied by the concept of methodology of performing tests. Necessary conditions, which were needed to minimize the influence of disturbing factors on the performance of thermal imaging measurements, were also indicated. Mentioned factors resulted...
-
LOW COST MEASUREMENT MODULE FOR MATRIX OF AMPEROMETRIC GAS SENSOR
PublikacjaThis paper describes an amperometric sensor module for gas concentration measurement. A module can be used for many types of electrochemical gas sensors without major hardware changes. Device is based on AVR ATmega8 microcontroller. As signal processing circuit a specialized integrated circuit LMP9l000 configurable via I2C interface is used. The concept of a measuring system composed of several modules dedicated for a gas sensors...
-
Wave propagation signals in concrete beams under 3-point bending
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beams with dimensions 40 x 40 x 160 cm3under the 3-point bending. The beams were made of concrete with the following ingredients: CEM I 42.5R (450 kg/m3), water (177 kg/m3), sand 0-2 (675 kg/m3) and gravel 2-8 (675 kg/m3). The bending test was performed using a Zwick/Roell Z10...
-
Low-power device simulator for micro-energy measurement methods testing
PublikacjaThe paper presents low-power device simulator designed for testing of micro-energy measurement methods. Such kind methods can be used for evaluation of power systems based on Energy Harvesting. The device allows to set the current consumption characteristic over the time, thus making possible playing the role of different types of low-power devices e.g. simulating sensor network node.
-
Analysis of distance measurement errors in CW FM sonar with MLS code modulation
PublikacjaAlthough used in the classic silent sonar, the CW FM sounding signal has a major flaw which is its inaccuracy in determining the distance to a target. The authors of the article have developed a concept of silent sonar using frequency modulation signals switched by pseudorandom codes, already discussed in their previous work. This article presents a detailed analysis of errors in CW FM sonar with pseudo-random sequence code modulation...
-
Measurement of idlers rotation speed in belt conveyors based on image data analysis for diagnostic purposes
Publikacja -
A method of two-terminal excess noise measurement with a reduction of measurement system and contact noise
PublikacjaPrzedstawiono metodę i system do pomiaru szumów nadmiarowych dwójników elektrycznych ze znaczną redukcją wpływu szumów własnych systemu pomiarowego i szumów kontaków. Proponowana metoda może byc zastosowana do pomiaru szumów elementów z wyprowadzonymi końcówkami, bądź też struktur, gdy jako wzorcowy szum odniesienia może zostać zastosowany szum struktury rezystywnej wytworzonej bezpośrednio na strukturze w otoczeniu elementu testowanego.
-
Instrumental measurement of odour nuisance in city agglomeration using electronic nose
PublikacjaThe paper describes an operation principle of odour nuisance monitoring network in a city agglomeration. Moreover, it presents the results of investigation on ambient air quality with respect to odour obtained during six-month period. The investigation was carried out using a network comprised of six prototypes of electronic nose and Nasal Ranger field olfactometers employed as a reference method. The monitoring network consisted...
-
Wood Moisture-Content Measurement Accuracy of Impregnated and Nonimpregnated Wood
PublikacjaThe influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated...
-
Evaluation of high-frequency roughness measurement errors for composite and ceramic surfaces after machining
PublikacjaPrecise characterisation of surface topography is of the greatest importance since many factors directly affect the accuracy of the whole measurement process. In this paper, the variety of surface topographies from machined composite and ceramic workpieces was studied with a special emphasis on the measurement results. Surfaces were subjected to the ground diamond, honing and milling processes. Measurement results were analysed...
-
The prototype of a wireless measurement card
Publikacja -
Spikes removal in surface measurement
Publikacja -
Air Pollutant Emission Measurement
Publikacja -
Evaluation of applicability of classic methods of a fault loop impedance measurement to circuits with residual current devices
PublikacjaMeasurement of fault loop impedance in low voltage grids and systems is in most cases performed to verify the effectiveness of protection against electric shock by automatic disconnection of supply. For the sake of measurement accuracy, it is advisable to perform it using large current. Unfortunately, in circuits with residual current devices which are very widely used nowadays, a large measurement current may trigger those devices...
-
Measurement Science Review
Czasopisma -
Dynamic unattended measurement based routing algorithm for diffServ architecture
PublikacjaDynamic routing is very important in terms of assuring QoS in today's packet networks especially for streaming and elastic services. Existing solutions dedicated to dynamic routing are often too complicated and seem to be not usable in real time traffic scenarios where transferred traffic may vary significantly. This was the main reason for research and new routing mechanism proposal which should apply to today's packet networks....
-
The set of 22 sessions of 14-channel eeg signals recorded during watching pictures
Dane BadawczeThe data were collected in order to perform research on the possibility of controlling the content displayed on the monitor screen using human emotional states extracted from EEG signals. The dataset contains recordings of 14-channel EEG signals collected from 10 persons within 22 sessions, during which 45 different random photos taken from the ImageNet...
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublikacjaWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublikacjaThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
Heart rate PPG signals with acceleration captured at wrist during small and moderate body movements
Dane BadawczeHeart rate PPG signals with acceleration captured at wrist during small and moderate body movements
-
A new method of fault loop resistance measurement in low voltage systems with residual current devices
PublikacjaThis paper presents a new method of fault loop resistance measurement in low voltage systems with residual current devices. The method enables measuring fault loop resistance without nuisance tripping of residual current devices, by application an unconventional waveform of measurement current. It is important for proper verification of the effectiveness of protection against electric shock.
-
Comparison of induction motor bearing diagnostic test results through vibration and stator current measurement
PublikacjaThe paper discusses results of tests performed by authors, related to the angine bearings diagnostic using vibration and stator current measurements. The paper contains the description of an automatic measurement system, developed for measurement of those harmonics and processing that to obtain bearing diagnostic information. System was tested on objects with intentionally made defects in bearings, results of this test was also...
-
Conditions for measurement, analog-to-digital conversion and frequency analysis of irregularities of profile surface
PublikacjaPrzedstawiono uwarunkowania pomiaru, przetwarzania analogowo-cyfrowego i analizy częstotliwościowej nierówności powierzchni toczonych dla celów rozpoznawania ich głównych składowych. Przedstawiono ograniczenia w pomiarze igłą, która odwzorowuje nierówności poprzeczne. Podano zależności parametrów pomiaru cyfrowego nierówności warunkujące zakresy ich rozpatrywania. Dla wartości przedziału próbkowania, dla którego nie jest spełnione...
-
Educational Measurement-Issues and Practice
Czasopisma -
Journal of Food Measurement and Characterization
Czasopisma -
Mediterranean Journal of Measurement and Control
Czasopisma -
IEEE INSTRUMENTATION & MEASUREMENT MAGAZINE
Czasopisma -
Modelling, Measurement and Control C
Czasopisma -
IET Science Measurement & Technology
Czasopisma -
Measurement-Interdisciplinary Research and Perspectives
Czasopisma -
Journal of Economic and Social Measurement
Czasopisma -
Modelling, Measurement and Control B
Czasopisma -
Measurement and Evaluation in Counseling and Development
Czasopisma -
Testing of Software for the Planning of a Linear Object GNSS Measurement Campaign under Simulated Conditions
PublikacjaThe precision of a linear object measurement using satellite techniques is determined by the number and the relative position of the visible satellites by the receiver. The status of the visible constellation is described by DOP. The obtained geometric coefficient values are dependent on many variables. When determining these values, field obstacles at the receiver location and satellite positions changing with time must be taken...
-
Method and measurement system for DC characteristics measurement of power diodes in very wide current range
PublikacjaW artykule przedstawiono układ pomiarowy do pomiaru charakterystyk stałoprądowych diod. Pomiar przeprowadzany jest metodą impulsową w celu zapewnienia stałej temperatury badanego elementu w trakcie pomiaru. Do zapewnienia odpowiedniej liczby punktów pomiarowych wykorzystano układ zmodyfikowanej drabinki R2R z pojedynczymi kluczami sterującymi.
-
Designing a magnetoacoustic emission measurement configuration for measurement of creep damage in power plant boiler tubes
PublikacjaOpisywane są własności skonstruowanego detektora emisji magneto-akustycznej (EMA) służącego dla pomiaru stopnia degradacji rurociągów w przemyśle energetycznym. Specjalna budowa biegunów magnesu umożliwia ich dopasowanie do zakrzywionych powierzchni. Układ pomiarowy pozwala na badanie natężenia EMA dla pola wzdłuż osi rury, a także w kierunku obwodowym. Wykazano, iż możliwa jest detekcja zmiany stopnia degradacji materiału na obwodzie...
-
STUDY OF ARRAY OF MEMS INERTIAL MEASUREMENT UNITS UNDER QUASI-STATIONARY AND DYNAMIC CONDITIONS
PublikacjaA measurement system includes all components in a chain of hardware and software that leads from a measured variable to processed data. In that context, the type and quality of the sensors or measuring devices are critical to any measurement system. MEMS/IMU sensors lag behind leading technologies in this respect, but the MEMS/IMU performance rapidly changes while is relatively inexpensive. For this reason, the paper proposes...
-
Time-scale modification of speech signals for supporting hearing impaired schoolchildren
PublikacjaA study of time scale modification algorithmsapplied to hearing impaired schoolchildren supporting ispresented. Variety of algorithms are considered, namely:overlap and add, two variations of synchronized overlapand add, and the phase vocoder. Their effectiveness as wellas real-time processing capabilities are examined.
-
Testing the Wide-Sense Stationarity of Bandpass Signals for Underwater Acoustic Communications
PublikacjaThe Underwater Acoustic Communication (UAC) systems work in communication channels characterized by a large variety of multipath propagation conditions that can additionally change over time. Designing a reliable communication system requires knowledge of the transmission parameters of the channel. There is a need for the development of adaptive signaling schemes that would dynamically optimize the signal parameters of the physical...
-
Potentiometric Solid-Contact Multisensor System for Simultaneous Measurement of Several Ions
PublikacjaThe design and performance of potentiometric multisensor system made in solid-contact technology is described. Both, the measuring electrodes as well as the reference electrode are in a compact cell. The system allows for simultaneous measurement of various ions. The characteristics of the electrodes for Na+, K+ and Ca2+ ions were determined using the designed system and compared with ISEs of the same membrane composition in classical...
-
PHYSIOLOGICAL MEASUREMENT
Czasopisma -
Quantum Steering Inequality with Tolerance for Measurement-Setting Errors: Experimentally Feasible Signature of Unbounded Violation
Publikacjauantum steering is a relatively simple test for proving that the values of quantum-mechanical measurement outcomes come into being only in the act of measurement. By exploiting quantum correlations, Alice can influence — steer — Bob ’ s physical system in a way that is impossible in classical mechanics, as shown by the violation of steering inequalities. Demonstrating this and similar quantum effects for systems of increasing size,...
-
Maciej Wróbel dr inż.
OsobyReceived PhD from Gdańsk University of Technology in 2019. Research interests involve non-invasive applications of Raman spectroscopy for tissue analysis, specifically blood parameters measurements. Tissue mimicking phantoms, measurement of optical properties (scattering, absorption), as well as other optical sensing methods. Raman spectroscopy and surface-enhanced Raman spectroscopy (SERS) utilized for measurements of biological...
-
Measurement and Analysis of the Radio Wave Polarisation in Off-Body Communications in Indoor Environment
PublikacjaThe paper describes an analysis of the radio wave polarisation in off-body communications in indoor environment. The measurement stand for polarisation measurements has been shortly described. Five investigated scenarios with different body postures and different antenna placements have been characterize. The vertical and horizontal components of received radio signal have been analysed. The measure used in analysis is a ratio...
-
Reduction of measurement data before Digital Terrain Model generation vs. DTM generalisation
PublikacjaModern data acquisition technologies provide large datasets that are not always necessary in its entirety to properly accomplish the goal of the study. In addition, such datasets are often cumbersome for rational processing, and their processing is time and labour consuming. Therefore, methods that enable to reduce the size of the measurement dataset, such as the generalization of the Digital Terrain Model (DTM) or the reduction...