Wyniki wyszukiwania dla: STEAM TURBINE CASING
-
Comparative analysis of the theoretical models of ideal propulsor, ideal fluid brake, ideal screw propeller and ideal axial wind turbine
PublikacjaThe article presents a detailed discussion of four different fluid dynamics devices.These devices are presented with all relevant mathematical formulae regarding the forces, the power and the efficiency. It is demonstrated that application of the Betz theorem to axial wind turbines is not correct and it underestimates the maximujm achievable efficiency. This conclusion is supported by numerical calculations.
-
Influence of gas turbine controller adjustment on ship propulsion system behaviour in rough sea conditions. Part 2. The simulation investigations.
PublikacjaPrzedstawiono model dynamiki układu napędowego okrętowego, wykorzystując metodę elementów skończonych. Układ napędowy składa się z dwóch turbin gazowych napędzających poprzez przekładnię mechaniczną zębatą pędnik o nastawnym skoku. W symulacji układu napędowego zadawano wymuszenia wartością zadaną nastaw prędkości na regulatorze oraz wymuszenia od falowania morza w zależności od stanu morza. Przedstawiono wyniki takich symulacji.
-
An analysis of the possibilities of increasing the production of electrical energy during the summer season by heat-generation back pressure turbine power units.
PublikacjaZbadano możliwości podniesienia mocy elektrycznej produkowanej przez przeciwprężne bloki ciepłownicze w sezonie letnim. Zbadano jedną z możliwości polegającą na dochładzaniu wody sieciowej powracającej z aglomeracji miejskiej. Zwrócono uwagę na aspekty techniczne, ekonomiczne i ekologiczne rozważanego rozwiązania.
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part I: Pressure field
PublikacjaPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na rozkład ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego nieznacznie zmienia rozkład ciśnienia w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem osi korpusu.
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part II: Forces and moments
PublikacjaPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na wymuszenia aerodynamiczne powstające w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego odgrywa niewielką rolę w generowaniu sił i momentów aerodynamicznych w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem...
-
An impact of ambient parameters change on steam and gas turboset control. The International Conference on ''Turbines of Large Output'' devoted to 100th Anniversary of prof. Robert Szewalski Birthday.
PublikacjaPorównano wpływ zmian parametrów otoczenia (ciśnienia i temperatury) na charakterystyki turbiny parowej i gazowej. Na tej podstawie zbadano wpływ tych parametrów na charakterystyki układu kombinowanego parowo-gazowego. Przedstawiono, w związku z tym, koncepcję kompensatora wpływu zmian parametrów otoczenia na charakterystyki układu kombinowanego parowo-gazowego.
-
Application of neural networks for identification of forcedness having effect on magnitude of turbine rotor vibration using pressure distribution in blade tip clearance.
PublikacjaW pracy sprawdzono, czy zastosowanie sieci neuronowych umożliwia identyfikację wymuszeń powstających w wyniku funkcjonowania maszyny jak i zależnych od jej stanu mechanicznego przy zastosowaniu rozkładu ciśnienia w uszczelnieniu nadbandażowym. Przeprowadzono pomiary rozkładu ciśnienia dla różnych warunków pracy, uwzględniając zmianę mimośrodu oraz zmianę skośnego ustawienia osi wirnika względem osi korpusu. Dokonano analiz przy...
-
Influence of gas turbine controller adjustment on propulsion system behaviour in high sea conditions. Part 1. The dynamic model of propulsion system.
PublikacjaDo badań przyjęto układ napędowy okrętowy z turbinami gazowymi napędzającymi poprzez przekładnię mechaniczną zębatą śrubę okrętową o zmiennym skoku. Nakład napędowy statku z turbinami gazowymi napędzającymi śrubę nastawną oddziałują wymuszenia zarówno od nastaw prędkości obrotowej wału śrubowego jaki skoku śruby napędowej, ale również istnieje silna reakcja od falowania morza (stanu morza) na pracę układu napędowego. Zbudowano...
-
3D calculations of aerodynamic forces causing self-excited vibrations of turbine rotor systems. Part I: Shroud seal flow inwestigations
PublikacjaOpisano numeryczną i doświadczalną metodę badania przepływu w uszczelnieniu nadbandażowym stopnia turbinowego. Badania numeryczne przeprowadzono programem Fluent, a badania doświadczalne wykonano na powietrznej turbinie modelowej. Uwzględniono niesymetryczny rozkład szczeliny nadbandażowej na skuteknie centrycznego położenia osi wirnika względem osi cylindra. Zamieszczono przykładowe wyniki.
-
Influence of adjustment of gas turbine controller on ship propulsion system behaviour in rough sea conditions. Part 1. The dynamic model of propulsion system.
PublikacjaPrzedstawiono model dynamiki układu napędowego okrętowego, wykorzystując metodę elementów skończonych. Układ napędowy składa się z dwóch turbin gazowych napędzających poprzez przekładnię mechaniczną zębatą pędnik o nastawnym skoku. W symulacji układu napędowego można zadawać wymuszenia wartością zadaną nastaw prędkości na regulatorze, wymuszenia od falowania morza w zależności od stanu morza, jak również zmianą ustawienia skoku...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Sterowanie systemu elektroenergetycznego zasilanego układem kombinowanym silnik spalinowy - turbina gazowa = Control of electric power system suplied with combined diesel engine and gas turbine
PublikacjaPoddano badaniom symulacyjnym układ sterowania automatyc znego elektroenergetycznego systemu wydzielonego, zasilanego prądnicami napędzanymi przez wysokoprężny silnik spalinowy oraz turbinę gazową. Przebieg procesów symulacyjnych zależy głównie od nastawień regulatora częstotliwości systemu elektroenergetycznego. Od ustawień regulatora silnika tłokowego zależy mniej niż w przypadku turbiny gazowej. Nie odgrywa istotnej roli sposób...
-
Increasing the lifetime of engineering structures through the use of composite laggings
PublikacjaThe use of composite laggings prevents concrete (chemical and biological) corrosion. Columns coated with composite or reinforced composite are more resistant to negative environmental impact on concrete or steel. The mechanical properties of the reinforced casing also cause that these types of columns are more resistant to lateral forces. The applied casing limits carbonization of concrete and cyclical freezing and thawing with...
-
Zbigniew Lubośny prof. dr hab. inż.
Osoby -
Laboratory research on the influence of swelling clay on the quality of borehole cementing and evaluation of clay-cutting wellbore tool prototype
PublikacjaSwelling clay phenomenon is frequently observed during oil and gas drilling operations and has a significant impact on the quality of cementing procedure. Certain types of clayey minerals increase their volume in contact with water-based drilling fluids. After drilling is completed, borehole remains unsupported and filled with waterbased drilling fluids for several hours, before a casing string is inserted and secured with cement....
-
Jerzy Łabanowski prof. dr hab. inż.
Osoby -
Michał Wasilczuk prof. dr hab. inż.
OsobyMichał Wasilczuk, absolwent Wydziału Budowy Maszyn Politechniki Gdańskiej (1986), a obecnie profesor zwyczajny na Wydziale Mechanicznym PG i kierownik Katedry Konstrukcji Maszyn i Pojazdów od początku swojej działalności naukowej zajmuje się hydrodynamicznymi łożyskami wzdłużnymi oraz, szerzej inżynierią łożyskowania, w ramach zespołu naukowego stworzonego przez doc. Olgierda Olszewskiego. Od kilkunastu lat zespół specjalizuje...
-
Heat Turbomachinery 2023_24
Kursy OnlineBasics of thermodynamical cycles. Elements of turbine power plants. Fluid problems in turbomachinery. Theory of turbine stages. Turbine flow parts.
-
The change of mechanical properties of selected wood species after drying process under various conditions
PublikacjaThe result of mechanical properties change of selected wood species after drying process under various parameters are presented. The global elasticity modulus and bending strength for steam dried, air-steam mixture dried and air dried samples as reference were measured. It allowed to reveal the effect of wood stream, air-steam mixture and their temperature on mechanical properties of wood. It has been recognized that steam and...
-
Michał Michna dr hab. inż.
OsobyJest absolwentem Wydziału Elektrycznego Politechniki Gdańskiej (1998). W 2004 r. uzyskał stopień doktora. Od 2004 r. zatrudniony w Katedrze Energoelektroniki i Maszyn Elektrycznych Politechniki Gdańskiej (asystent, adiunkt, starszy wykładowca). W latach 2010-2015 zastępca kierownik katedry. Jego zainteresowania naukowe i dydaktyczne obejmują szerokie spektrum zagadnień związanych z projektowanie, modelowanie i diagnostyką maszyn...
-
O strumieniu mocy w silniku lub w układzie napędowym
PublikacjaW silniku lub w układzie napędowym wielkość strumienia mocy rośnie w kierunku przeciwnym do kierunku przepływu mocy. Straty energetyczne i sprawność energetyczna silnika lub układu napędowego powinny być przedstawiane jako funkcje wielkości fizycznych niezależnych od strat. Takimi wielkościami są prędkość i obciążenie silnika. Jednakże obraz strumienia mocy w silniku lub w układzie napędowym jest przedstawiany w literaturze w formie...
-
On power stream in motor or drive system
PublikacjaIn a motor or in a drive system the quantity of power increases in the direction opposite to the direction of power flow. Energy losses and energy efficiency of a motor or a drive system must be presented as functions of physical quantities independent of losses. Such quantities are speed and load. But the picture of power stream in a motor or in a drive system is presented in the literature in the form of traditional Sankey...
-
Fundamentals of thermodynamics and heat transfer, W/C, GTM (WCh), sem.04, zimowy 23/24 (PG_00048767)
Kursy OnlineTable of contents presented on the course: Basic terms.The first law of thermodynamics for closed and open systems.The properties of perfect, semi-perfect and real gases.Gas rights. Thermal and caloric state equation.Thermodynamic transformations of a perfect gas.Gaseous thermodynamic cycles. The second law of thermodynamics.Steam and steam cycles.Basics of heat exchange.
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublikacjaAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Thermodynamic Cycles of Air Microturbine Power Plants Working on Biomass Fuels
PublikacjaThe gas turbine engine is modified to work as an air turbine set which consists, in the simplest arrangement, of a compressor, a heat exchanger and a turbine. Air is a working medium for both: the compressor and the turbine. This kind of air turbine set can be applied in power plants working on biomass fuels. In this solution we can burn fuels of varying parameters in the external combustion chamber without any harmful effects...
-
Zdzisław Kowalczuk prof. dr hab. inż.
OsobyW 1978 ukończył studia w zakresie automatyki i informatyki na Wydziale Elektroniki Politechniki Gdańskiej, następnie rozpoczął pracę na macierzystej uczelni. W 1986 obronił pracę doktorską, w 1993 habilitował się na Politechnice Śląskiej na podstawie pracy Dyskretne modele w projektowaniu układów sterowania. W 1996 mianowany profesorem nadzwyczajnym, w 2003 otrzymał tytuł profesora nauk technicznych. W 2006 założył i od tego czasu...
-
Revalorization of the Szewalski binary vapour cycle
PublikacjaThe aim of the paper is to revalorizate of the Szewalski binary vapour cycle by analysing thermodynamical and operational parameters of this cycle. This was carried by accessible numerical CFM (Computational Flow Mechanics) codes type, by step-by-step modeling of separates apparatus. The binary vapour cycle is providing steam as the working fluid in the high temperature part of the cycle, while another fluid - a low boiling point...
-
Moisture content during and after high- and normal-temperature drying processes of wood
PublikacjaThe aim of the article is to present the results of moisture content of wood during and after the high-temperature steam and air–steam mixture drying processes and after an open air-drying process. The knowledge of moisture content changes of wood in the process of its drying is one of the important parameters to economy drying process and to keep the quality of dried wood. Wood samples, namely, spruce (Picea abies K.) and beech...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublikacjaThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublikacjaThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublikacjaThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
The influence of drying parameters on wood properties
PublikacjaResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
Small Scale Gasification of Biomass and Municipal Wastes for Heat and Electricity Production using HTAG Technology
PublikacjaCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900degC provides additional energy to conversion processes and results in considerable...
-
Phong B. Dao D.Sc., Ph.D.
OsobyPhong B. Dao received the Engineer degree in Cybernetics in 2001, the M.Sc. degree in Instrumentation and Control in 2004, both from Hanoi University of Science and Technology in Vietnam, and the Ph.D. degree in Control Engineering in 2011 from the University of Twente, the Netherlands. In May 2020, Dr. Dao received the degree of D.Sc. (Habilitation) in Mechanical Engineering from the AGH University of Science and Technology, Poland....
-
Eulerian motion magnification applied to structural health monitoring of wind turbines
PublikacjaSeveral types of defects may occur in wind turbines, as physical damage of blades or gearbox malfunction. A wind farm monitoring and damage prediction system is built to observe abnormal vibrations of elements of wind turbine: blades, nacelle, and tower. Contactless methods are developed which do not require turbine stopping. In this work, structural health monitoring of a wind turbine is evaluated using a conversion from the captured...
-
The influence of drying parameters on wood properties
PublikacjaThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
The system for remote monitoring of a vertical axis wind farm
PublikacjaThe article presents a system for remote monitoring of working parameters of a wind turbine with a vertical axis. The monitoring system was built using a Raspberry PI 3 microcomputer with the Raspbian operating system and a MicroDAQ E2000 measuring card. The developed system enables monitoring the power output of the generator, torque on the turbine shaft, turbine speed and wind speed. The values of the monitored parameters are...
-
THE THERMODYNAMIC ANALYSIS OF THE SZEWALSKI HIERARCHIC VAPOUR CYCLE COOPERATED WITH THE SYSTEM OF HEAT RECOVERY
PublikacjaIn this paper, thermodynamic analysis of the Szewalski hierarchic vapour cycle cooperated with the system of heat recovery from exhaust gases are presented. According to that purpose, the CFM (Computation Flow Mechanics [1,3]) approach has correctly been used. The whole system consists of the first traditional steam cycle, the second organic Rankine cycle (ORC) and system of heat recovery with use of water with temperature 90...
-
Janusz Cieśliński prof. dr hab. inż.
OsobyUrodził się 15 kwietnia 1954 r. w Słupsku. Jest absolwentem Wydziału Budowy Maszyn Politechniki Gdańskiej (1978), z którą związał całe swoje życie zawodowe. W 1986 r. obronił doktorat, w 1997 r. – habilitację, w 2006 r. – uzyskał tytuł profesora. Pełnił funkcje prodziekana ds. nauki Wydziału Mechanicznego przez dwie kadencje (2002–2008) oraz kierownika: Katedry Maszyn Przemysłu Spożywczego (2002–2006), Katedry Ekoinżynierii i...
-
Rotordynamic characteristics of a chamber seal
PublikacjaThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal of a modernized type. The experiments were performed on a single-stage air model turbine of the impulse type. The experiments were performed on a single-stage air model turbine of the impulse type. The experimental data were compared with theoretical results obtained by means of CFD Fluent Code....
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublikacjaSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublikacjaThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
ANALIZA AERODYNAMICZNA ŁOPAT NA PRZYKŁADZIE PROJEKTU DWUWIRNIKOWEJ TURBINY WIATROWEJ MAŁEJ MOCY
PublikacjaW artykule przedstawiono proces projektowania oraz analizy aerodynamicznej łopat turbiny wiatrowej z wykorzystaniem metody BEMT (ang. Blade Element Momentum Theory). Dokonano doboru profili aerodynamicznych oraz opisano procedurę wyznaczania optymalnego rozkładu kątów zwichrowania i długości cięciw profili w funkcji długości łopaty dla założonych parametrów wejściowych. Dokonano obliczenia działających sił oraz generowanej mocy...
-
Twin volute admission as an alternative inlet configuration for a steam tu- rbine.**2002, 164 s. 155 rys. bibliogr. 14 poz. maszyn. Podwójna spirala zasilająca jako alternatywny wlot do turbiny parowej. Rozprawa doktorska /2002.06.05/. PG, Wydz. Mechaniczny. Promotor: prof. dr hab. inż. R. Puzyrewski.
Publikacja.
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublikacjaThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublikacjaWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...