wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: APPROACH PARAMETERS
-
Application of total parameters in environmental analytics
PublikacjaPrzedstawiono klasyfikację technik oznaczania tzw. parametrów sumarycznych w próbkach środowiskowych (powietrze, woda, gleba) oraz obszar wykorzystania parametrów sumarycznych w analityce środowiskowej.
-
Experimental study on plate modal parameters
PublikacjaTest doświadczalny jest częścią systemu diagnostycznego. Autorzy badają wpływ dodatkowej masy na parametry modalne wolno popartej stalowej płytyi. Artykół przedstawia technikę wyznaczania parametrów modalnych dla systemów monitorowania konstrukcji.The experimental test introduced in the paper is the part of the diagnostic system. The authors investigate the influence of the additional mass on modal parameters of simply supported...
-
Selection of the tunnel thuster main parameters.
PublikacjaPrzedstawiono przegląd podstawowych odmian konstrukcyjnych sterów strumieniowych urządzeń zalecanych przez producentów. Z uwagi na znaczne różnice wartości otrzymywane z wymienionych metod, zamieszczono także wyniki analizy statystycznej sterów strumieniowych zastosowanych na statkach zbudowanych w Stoczni Gdynia w latach1995-2002. Porównanie wyników poszczególnych metod z parametrami sterów zastosowanych na wymienionych...
-
VIBRATION PARAMETERS FOR DAMAGE DETECTION IN STRUCTURES
PublikacjaThe aim of this paper is to examine how damage indicators are sensitive to changing number of frequencies and mode shapes and also to number and location of measurement points. The influence of measurement errors was also analyzed for all cases. For the analysis, those damage indicators are chosen which use changes in such modal parameters as natural frequencies and mode shapes and also differences between the curvatures of the damaged...
-
Frequency Diagnostics of Transformer Insulating Parameters
PublikacjaIn the article is presented experimental analysis and diagnostics of insulating system oil-paper for power transformers, mainly by progressive frequency method – dielectric spectroscopy. In the 1-st part of the article is described base theory about measurement and diagnostics insulating part (oil and paper) of power transformers. In the 2-nd part of article is described measuring method of insulating frequency diagnostics - frequency...
-
Quality Parameters in IMS/NGN Networks
PublikacjaThe Next Generation Network (NGN) architecture, including elements of the IP Multimedia Subsystem (IMS) concept, is a proposition of a telecommunication network dedicated to the needs of current and future information society. The main goal of NGN is to provide Quality of Service (QoS), for which proper network design is necessary with respect to among others standardized call processing performance parameters, including expected...
-
Alternative convolution approach to friction in unsteady pipe flow
PublikacjaIn the paper some aspects of the unsteady friction in pipe flow expressed by the convolution are analyzed. This additional term introduced into the motion equation involves the accelerations of fluid occurring in the past and a weighting function. The essence of such approach is to assume the appropriate form of weighting function. However, until now no fully reliable formula for this function has been found. To avoid some inconveniences...
-
The OpenMolcas Web: A Community-Driven Approach to Advancing Computational Chemistry
Dane BadawczeThe developments of the open-source OpenMolcas chemistry software environment since spring 2020 are described, with a focus on novel functionalities accessible in the stable branch of the package or via interfaces with other packages. These developments span a wide range of topics in computational chemistry and are presented in thematic sections: electronic...
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Dane BadawczeTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
On DoA estimation for rotating arrays using stochastic maximum likelihood approach
PublikacjaThe flexibility needed to construct DoA estimators that can be used with rotating arrays subject to rapid variations of the signal frequency is offered by the stochastic maximum likelihood approach. Using a combination of analytic methods and Monte Carlo simulations, we show that for low and moderate source correlations the stochastic maximum likelihood estimator that assumes noncorrelated sources has accuracy comparable to the...
-
Systematic approach to binary classification of images in video streams using shifting time windows
Publikacjain the paper, after pointing out of realistic recordings and classifications of their frames, we propose a new shifting time window approach for improving binary classifications. We consider image classification in tewo steps. in the first one the well known binary classification algorithms are used for each image separately. In the second step the results of the previous step mare analysed in relatively short sequences of consecutive...
-
Comparison of classical and modern approach of determination of highly polar compounds by High Performance Liquid Chromatography coupled with Tandem Mass Spectrometry
PublikacjaAbstract: Sugars and sugar alcohols are known as highly polar compounds. Four analytes were taken into consideration for comparison of classical and modern approach of separation of highly polar substances. Mannitol was chosen as an example of simple sugar alcohol, sucrose and lactulose as examples of disaccharides and structural isomers, raffinose as an example of complex trisaccharide. Raffinose was also used as internal standard...
-
Mutual Coupling Reduction in Antenna Arrays Using Artificial Intelligence Approach and Inverse Neural Network Surrogates
PublikacjaThis paper presents a novel approach to reduce undesirable coupling in antenna arrays using custom-designed resonators and inverse surrogate modeling. To illustrate the concept, two stand-ard patch antenna cells with 0.07λ edge-to-edge distance are designed and fabricated to operate at 2.45 GHz. A stepped-impedance resonator is applied between the antennas to suppress their mutual coupling. For the first time, the optimum values...
-
The accuracy of a new approach to order determination for the Modified Prony method in swath mapping application
PublikacjaThis article presents the performance of a new approach to determine the model order for the modified Prony method applied to swath acoustic mapping. Key requirements for any mapping application are depth determination accuracy and angular resolution. Depth determination accuracy is strictly related to angular accuracy and geometrical relations between receiver and sources of the backscattered signal. Angular resolution determines...
-
The influence of process parameters on photocatalytic hydrogen production
Publikacja -
Minimum order of graphs with given coloring parameters
PublikacjaA complete k-coloring of a graph G=(V,E) is an assignment F: V -> {1,...,k} of colors to the vertices such that no two vertices of the same color are adjacent, and the union of any two color classes contains at least one edge. Three extensively investigated graph invariants related to complete colorings are the minimum and maximum number of colors in a complete coloring (chromatic number χ(G) and achromatic number ψ(G), respectively),...
-
Determining the viscoplastic parameters of rubber-toughened plastics
PublikacjaW artykule omówiono szczegółowo zastosowanie sprężysto-lepkoplastycznego prawa Bodnera-Partoma do opisu zachowania się tworzywa sztucznego (kopolimer etylenowo-propylenowy). Parametry materiałowe ustalono na podstawie jednoosiowych testów jednoosiowego rozciągania. Proponowane podejście jest zilustrowane przykładami obliczeniowymi w programie MSC.Marc z wykorzystaniem procedury UVSCPL.
-
Optimization of steam cycles with respect to supercritical parameters
PublikacjaArtykuł zawiera analizę budowanych aktualnie bloków nadkrytycznych stosowanych na świecie. W pracy przeprowadzono analizę obiegów z pojedynczym oraz podwójnym przegrzewem międzystopniowym dodatkowo z regeneracyjnym podgrzewem wody zasilającej odpowiednio z sześcioma, siedmioma, ośmioma, dziewięcioma oraz dziesięcioma wymiennikami regeneracyjnymi. Obliczenia wykonywano dla różnych wartości temperatur i ciśnienia pary świeżej, różnych...
-
Interpretation of Structural Parameters for Models with Spatial Autoregression
Publikacja -
Domination-Related Parameters in Rooted Product Graphs
PublikacjaAbstract A set S of vertices of a graph G is a dominating set in G if every vertex outside of S is adjacent to at least one vertex belonging to S. A domination parameter of G is related to those sets of vertices of a graph satisfying some domination property together with other conditions on the vertices of G. Here, we investigate several domination-related parameters in rooted product graphs.
-
Modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents method of the modal parameters identification based on the Particle Swarm Optimization (PSO) algorithm [1]. The basic PSO algorithm is modified in order to achieve fast convergence and low estimation error of identified parameters values. The procedure of identification as well as algorithm modifications are presented and some simple examples for the SISO systems are provided. Results are compared with the results...
-
Thermal-Humidity Parameters of 3D Printed Wall
Publikacja -
Barkhausen Noise Calculation by Hysteresis Model Parameters
PublikacjaPętla histerezy natężenia efektu Barkhausena wyliczono wykorzystując model histerezowy. Założono, iż straty energii na efekt Barkhausena zależą od szybkości granicy domenowej oraz od częstości występowania skoków Barkhausena. Pokazano wyliczenia wykonane dla stali Fe-Si (ziarna zorientowane w kierunku [100] względem kierunku walcowania)
-
Uncertainty in measuring noise parameters of a communication receiver
PublikacjaPrzedstawiono sposób pomiarów mocy dźwięku generowanego przez silnik sytemu napędowego z przemiennikiem częstotliwości. Wyprowadzono wyrażenie na niepewność wyznaczania mocy dźwięku emitowanego przez silnik, przy użyciu pomiarów poziomu dźwięku. Niepewność wyników pomiarów była szacowana w oparciu o metodę typu B. Przedstawiono wyniki badań laboratoryjnych i analizy wybranych składników niepewności dla układu napędowego z silnikiem...
-
Microscopic parameters of gas via acoustic measurements
PublikacjaProponujemy wstępną analizę odwrotnego problemu, który sformułowano, opartą na statycznej mechanice /termodynamice, rozważającej gaz jako środek rozprzestrzeniania dzwięku.
-
Fatigue criterial parameters of variable amplitude stress.
PublikacjaPrzedstawiono oryginalne kryterialne parametry zmęczeniowe naprężenia o zmiennej amplitudzie. Dla ich wyznaczenia założono, że wydatkowana w procesie zmęczenia energia jest proporcjonalna do energii sprężystego odkształcenia postaciowego. Jeżeli przyrost zniszczenia spowodowanego przez nj cykli naprężenia o stałej amplitudzie aj jest odniesiony do energii sprężystego odkształcenia postaciowego przekazanej jednostkowej objętości...
-
The flux compression generator load parameters selection
PublikacjaComputer simulation results of the flux compression generator (FCG) loaded with an inductor has been presented in this paper. Simulation research has been performed in order to select the parameters of FCG load coil properly. The influence of the load inductance and resistance on the current gain factor and the magnetic field energy accumulated in a load coil has been investigated.
-
EVALUATION OF 3D MODEL OF REBAR FOR QUANTITATIVE PARAMETERS
PublikacjaThe construction industry practices and processes are evolving constantly, and with the emergence of Industry 4.0, the use of technologies is expanding. Construction progress monitoring is an essential project lifecycle process; project success and timely completion are linked with effective progress monitoring operations and adopted tools. In the domain of automated construction progress monitoring, 3D modeling techniques have...
-
Evaluation of suspended rail vehicle movement parameters
PublikacjaNiniejsza publikacja została poświęcona ocenie parametrów ruchowych koncepcyjnego pojazdu kolei podwieszanej, którą dokonano w oparciu o jego charakterystykę trakcyjną oraz możliwości dynamiczne. W pierwszej kolejności skrótowo opisano konstrukcję proponowanego pojazdu wraz z wyszczególnieniem najważniejszych założeń projektowych. Następnie skupiono się na metodyce oraz samym wykreśleniu charakterystyki trakcyjnej pojazdu, jak...
-
Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
PublikacjaThe enormous use of cutting fluid in machining leads to an increase in machining costs, along with different health hazards. Cutting fluid can be used efficiently using the MQL (minimum quantity lubrication) method, which aids in improving the machining performance. This paper contains multiple responses, namely, force, surface roughness, and temperature, so there arises a need for a multicriteria optimization technique. Therefore,...
-
Using multibeam echoes in seafloor characterisation and classification
PublikacjaThe method of seabed identification and classification from multibeam sonar echoes is presented. The proposed approach is based on calculation of a set of parameters of an echo envelope, similarly as in seafloor classification using single beam echosounder. These parameters are extracted for each consecutive beam allowing the estimation of their dependence on the seafloor incident angle. The relation between seabed type and calculated...
-
Tracking Moving Objects in Video Surveillance Systems with Kalman and Particle Filters – A Practical Approach
PublikacjaThis Chapter focuses on the first type of object tracking algorithms, namely on Kalman and particle filters. A theory of these algorithms may be found in many publications, there are also reports on implementation of these approaches to object tracking in video. However, developers of VCA systems still face two important problems. The first one is related to obtaining accurate measurements of positions and sizes of the tracked...
-
Evaluation of a Novel Approach to Virtual Bass Synthesis Strategy
PublikacjaThe aim of this paper is to present a novel approach to the Virtual Bass Synthesis (VBS) strategy applied to portable computers. The developed algorithms involve intelligent, rule-based settings of bass synthesis parameters with regard to music genre of an audio excerpt and the type of a portable device in use. The Smart VBS algorithm performs the synthesis based on a nonlinear device (NLD) with artificial controlling synthesis...
-
Thermo-resonance analysis of an excited graphene sheet using a new approach
PublikacjaForced vibration of graphene nanoplate based on a refined plate theory in conjunction with higher-order nonlocal strain gradient theory in the thermal environment has been investigated. Regarding the higher-order nonlocal strain gradient theory, both stress nonlocality and size-dependent effects are taken into account, so the equilibrium equations which are governing on the graphene sheet have been formulated by the theory....
-
AN INNOVATIVE APPROACH TO PREDICTION ENERGETIC EFFECTS OF WOOD CUTTING PROCESS WITH CIRCULAR-SAW BLADES
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. The aim of the paper is to present a new calculating model using the application of modern fracture mechanics and to compare cutting parameters of native beech, Bendywood...
-
Simplified Approach for Broadband RF Testing of Low Loss Magneto-Dielectric Samples
PublikacjaIn this paper, an attractive measurement techniqueis proposed to retrieve the broadband permittivity and permeabil-ity of the magneto-dielectric materials. The proposed techniqueis quite novel which mitigates the major problems associatedwith the conventional broadband RF material characterizationtechniques such as numerical instability and phase uncertaintywhen the length of the sample exceeds...
-
Identification of Bodner-Partom model parameters for technical fabrics
PublikacjaThe thorough analysis of modeling technical fabrics behavior with the viscoplastic Bodner-Partom constitutive law is presented. The study has been focused on differences between the warp and weft direction of the material. To obtain the model’s parameters only the uniaxial tensile laboratory tests with three different, but constant strain rates are required. The parameters have been found for polyester fibers PVC coated fabrics:...
-
Optimizing the parameters of a small standalone hybrid power system
PublikacjaA hybrid power plant consists of renewable energy resources, an energy storage, a discharge load and an emergency power supply. Power plant parameters are tailored to meet the requirements of continuity of supply, cost minimization, return on investment period and system capacity utilization. The papaer presents the methodology for selecting power plant parameters with a larger number of decision criteria. The task is solved...
-
Determining efficient values of continuous technological machines parameters
Publikacja -
Parameters identification of coreless axial fluxpermanent magnet generator
Publikacja -
Strength parameters of masonry walls in modelling historic constructions
PublikacjaThe paper presents the determination of the basic material properties of a historic brickwork. Experimental studies were used to identify the basic material properties of bricks. The mechanical properties of the masonry, as an orthotropic homogenized material, were calculated. Then, numerical simulations using the Finite Element Method (FEM) were performed to verify the experimental outcomes. Macromodels with element sizes of 40,...
-
On the EM algorithm for the estimation of speech AR parameters in noise
Publikacja -
Estimation of Parameters Associated With Individual Sources of Voltage Fluctuations
Publikacja -
Influence of hydrothermal synthesis parameters on the properties of hydroxyapatite nanoparticles
Publikacja -
1,4-DHP-lipid parameters and rod like micellae
Publikacja -
Profile and Areal Surface Parameters for Fatigue Fracture Characterisation
Publikacja -
Cavity parameters identification for TESLA control system development
Publikacja -
Neural Network - Based Parameters Estimations Of Induction Motors
PublikacjaW artykule przedstwaiono algorytmy estymacji rezystancji wirnika i indukcyjności wzajemnej w zamkniętym układzie sterowania prędkości silnika indukcyjnego klatkowego. Do wyznaczenia rezystancji wykorzystano algorytm oparty na porównaniu modelu napięciowego i prądowego silnika. Do wyznaczania indukcyjności wykorzystano, znaną z literatury, zależność modelu multiskalarnego. Wyznaczane w stanie ustalonym parametry zapisywane są w...
-
Investigations of speech signal parameters with regard to articulation influences
PublikacjaW pracy zostało podjęte zagadnienie parametryzacji sygnału mowy w kontekście ekstrakcji cech biometrycznych. Analizowane parametry to parametry cepstralne (cepstrum liniowe i mel-cepstrum, czyli MFCC), parametry liniowej predykcji (LPC) oraz momenty widmowe i parametr F0. Zastosowano analize w krótkich stałych segmentach sygnału z zastosowaniem dużego zakładkowania, tzw. ''implicite segmentation''. Umożliwiło to zaobserwowanie...
-
Adaptive selection of control parameters in differential evolution algorithms
PublikacjaW pracy przedstawiono metodę adaptacyjnej selekcji parametrów kontrolnych w różnicowych algorytmach ewolucyjnych. Wartości parametrów takich jak: stopień krzyżowania i współczynnik różnicowej mutacji są odpowiednio zmieniane. Funkcje testowe użyte do testowania proponowanej metody były zaczerpnięte z literatury. Rezultaty uzyskane przy użyciu opisanej metody zostały porównane z innymi metodami selekcji różnicowej. Wyniki te, uzyskane...