Wyniki wyszukiwania dla: APRIORI ALGORITHM, QUALITY CONTROL, LAMINATE DEFECTS
-
Using Isolation Forest and Alternative Data Products to Overcome Ground Truth Data Scarcity for Improved Deep Learning-based Agricultural Land Use Classification Models
PublikacjaHigh-quality labelled datasets represent a cornerstone in the development of deep learning models for land use classification. The high cost of data collection, the inherent errors introduced during data mapping efforts, the lack of local knowledge, and the spatial variability of the data hinder the development of accurate and spatially-transferable deep learning models in the context of agriculture. In this paper, we investigate...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Comparison of Ozonation and Evaporation as Treatment Methods of Recycled Water for Bioethanol Fermentation Process
PublikacjaThe paper compared the performance of the ethanol yield after alcoholic fermentation with samples of rejected (RW) and permeate water (PW), RW and PW treated by oxidation with ozone (O3) (5 and 15 min) and evaporation, aiming the recirculation back to the bioethanol process. RW and PW were collected after an anaerobic bioreactor (AnBR) used for stillage treatment. Nine types of fermentations were made, where one used 100% tap...
-
Proportional-Derivative and Model-based Controllers used for a Serial Type Manipulator in case of a Variable Mass Payload
PublikacjaIn the paper, numerical analysis of dynamics of a variable mass system is considered. Its reference example is a serial-like manipulator composed of revolute joints and rigid bodies. Payload of its gripper is considered as its variable mass element (mass and inertia irregularly between subsequent payloads). For the rest of the system, inertia parameters are considered as known (precisely identified during the assembling process)....
-
Audio codec employing frequency-derived tonality measure
PublikacjaA transform codec employing efficient algorithm for detection of spectral tonal components is presented. The tonality measure used in MPEG psychoacoustic model is replaced with the method providing adequate tonality estimates even if the tonal components are deeply frequency modulated. The reliability of hearing threshold estimated using psychoacoustic model with standardized tonality measure and the proposed one is investigated...
-
SONIC - Self-optimizing narrowband interference canceler: comparison of two frequency tracking strategies
PublikacjaThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time linear stable plant with unknown and possibly time-varying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. The proposed disturbance...
-
Rating Prediction with Contextual Conditional Preferences
PublikacjaExploiting contextual information is considered a good solution to improve the quality of recommendations, aiming at suggesting more relevant items for a specific context. On the other hand, recommender systems research still strive for solving the cold-start problem, namely where not enough information about users and their ratings is available. In this paper we propose a new rating prediction algorithm to face the cold-start...
-
Development and Research of the Text Messages Semantic Clustering Methodology
PublikacjaThe methodology of semantic clustering analysis of customer’s text-opinions collection is developed. The author's version of the mathematical models of formalization and practical realization of short textual messages semantic clustering procedure is proposed, based on the customer’s text-opinions collection Latent Semantic Analysis knowledge extracting method. An algorithm for semantic clustering of the text-opinions is developed,...
-
Dynamic Signal Strength Mapping and Analysis by Means of Mobile Geographic Information System
PublikacjaBluetooth beacons are becoming increasingly popular for various applications such as marketing or indoor navigation. However, designing a proper beacon installation requires knowledge of the possible sources of interference in the target environment. While theoretically beacon signal strength should decay linearly with log distance, on-site measurements usually reveal that noise from objects such as Wi-Fi networks operating in...
-
Laxer Clinical Criteria for Gaming Disorder May Hinder Future Efforts to Devise an Efficient Diagnostic Approach: A Tree-Based Model Study
PublikacjaInternet Gaming Disorder (IGD) has been recognized in May 2013 and can be evaluated using the criteria developed by American Psychiatric Association (APA). The present study investigated the role each IGD criteria plays in diagnosing disordered gaming. A total of 3,377 participants (mean age 20 years, SD = 4.3 years) participated in the study. The data collected was scrutinized to detect patterns...
-
Optimization-based antenna miniaturization using adaptively-adjusted penalty factors
PublikacjaThe continuing trend for miniaturization of electronic devices necessitates size reduction of the comprising components and circuitry. Specifically, integrated circuit-antenna modules therein require compact radiators in applications such as 5G communications, implantable and on-body devices, or internet of things (IoT). The conflict between the demands for compact size and elec-trical and field performance can be mitigated by...
-
Assessment of the factors influencing on the formation of energy-oriented modes of electric power consumption by water-drainage installations of the mines
PublikacjaPurpose. Performing the analysis to determine energy-efficient modes and assess the characteristics of the main indicators of electric power consumption by mine water-drainage installations based on the developed research mathematical model. Methods. To achieve the purpose set, a methodology is used to develop the multiple multifactor correlation-regression modeling with respect to the modes of electric power consumption by electrical...
-
Rapid on-line method of wastewater parameters estimation by electronic nose for control and operating wastewater treatment plants toward Green Deal implementation
PublikacjaIn order to comply with legal regulations related to wastewater quality, the operational mode of facilities at wastewater treatment plant (WWTP) should be properly adjusted according to parameters of influents, however it is very difficult without frequently performed measurements. Currently there are known many techniques and devices for assesment of wastewater parameters such as chemical oxygen demand, biochemical oxygen demand,...
-
Application of the near-infrared spectroscopy in the pharmaceutical technology
PublikacjaNear-infrared (NIR) spectroscopy is currently the fastest-growing and the most versatile analytical method not only in the pharmaceutical sciences but also in the industry. This review focuses on recent NIR applications in the pharmaceutical technology. This article covers monitoring, by NIR, of many manufacturing processes, such as granulation, mixing or drying, in order to determine the end-point of these processes. In this...
-
Application of vibrational spectroscopy, thermal analyses and X-Ray diffraction in the rapid evaluation of the stability in solid-state of ranitidine, famotidine and cimetidine
PublikacjaThis paper reports the study on applicability of Fourier transform infrared (FTIR), near-infrared (NIR) and Raman spectroscopy, differential scanning calorimetry (DSC) and X-ray diffraction (XRD) for the estimation of the chemical stability and photostability of histamine H2-receptor antagonist substances. Ranitidine hydrochloride (RAN), famotidine (FAM) and cimetidine (CIM) were tested and differences in sensitivity were measured...
-
Literature update of analytical methods for biogenic amines determination in food and beverages
PublikacjaBiogenic amines (BAs) have been reported in a variety of foods, such as fish, meat, cheese, and wines. The formation of BAs in food by the microbial decarboxylation of amino acids can result in human allergic reactions, characterized by difficulty in breathing, rash, vomiting, and hypertension. Control measures to prevent biogenic amine formation in foods and/or reduce their levels should be considered. Therefore, monitoring of...
-
Leader election for anonymous asynchronous agents in arbitrary networks
PublikacjaWe consider the problem of leader election among mobile agents operating in an arbitrary network modeled as an undirected graph. Nodes of the network are unlabeled and all agents are identical. Hence the only way to elect a leader among agents is by exploiting asymmetries in their initial positions in the graph. Agents do not know the graph or their positions in it, hence they must gain this knowledge by navigating in the graph...
-
A Centralized Reputation System for MANETs Based on Observed Path Performance
PublikacjaA reputation system for MANETs is described that attempts to deduce nodal trustworthiness (forwarding behaviour) from observed end-to-end path performance. The trustworthiness deduction algorithm produces interval estimates and works well if node misbehaviour is not selec-tive with respect to traversing paths. Nodal reputation levels are next calculated in the spirit of generous tit-for-tat so as to best reflect momentary nodal...
-
Technique for reducing erosion in large-scale circulating fluidized bed units
PublikacjaThis paper presents a methodology, implemented for a real industrial-scale circulating fluidized bed boiler, to mitigate the risk of heating surfaces exposed to an intensive particle erosion process. For this purpose, a machine learning algorithm was developed to support the boiler reliability management process. Having a tool that can help mitigate the risk of uncontrolled power unit failure without expensive and technically complex...
-
The Simulation of Activated Sludge System for Optimization of Predictive Aeration at Large WWTP
PublikacjaEffective use of biodegradable substrates as an internal carbon sources (ICS) for denitrification and EBPR and predicting performance of aeration systems during nitrification in activated sludge bioreactors, may be useful in realization the sustainable development by potentially saving energy consumption at WWTPs. A large number of WWTPs use activated sludge systems with an integrated removal of carbon, nitrogen and phosphorus...
-
Fast Multi-Objective Aerodynamic Optimization Using Sequential Domain Patching and Multifidelity Models
PublikacjaExploration of design tradeoffs for aerodynamic surfaces requires solving of multi-objective optimization (MOO) problems. The major bottleneck here is the time-consuming evaluations of the computational fluid dynamics (CFD) model used to capture the nonlinear physics involved in designing aerodynamic surfaces. This, in conjunction with a large number of simulations necessary to yield a set of designs representing the best possible...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
Structure and the space vector modulation for a medium-voltage power-electronic-transformer based on two seven-level cascade H-bridge inverters
PublikacjaThis study presents the structure and the space vector pulse-width modulation (SVPWM) for power electronic transformer (PET) based on two seven-level cascade H-bridge (CHB) inverters. The DC links of CHB inverters are coupled with nine dual-active bridge (DAB) converters with medium-frequency transformers. The DC-link voltages are equalised with two methods – through the control of DAB voltages...
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublikacjaMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublikacjaIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Improved Design Closure of Compact Microwave Circuits by Means of Performance Requirement Adaptation
PublikacjaNumerical optimization procedures have been widely used in the design of microwave components and systems. Most often, optimization algorithms are applied at the later stages of the design process to tune the geometry and/or material parameter values. To ensure sufficient accuracy, parameter adjustment is realized at the level of full-wave electromagnetic (EM) analysis, which creates perhaps the most important bottleneck due to...
-
A New Method for Automatic Generation of Animated Motion
PublikacjaA new method for generation of animation with a quality comparable to a natural motion is presented. Proposed algorithm is based on fuzzy description of motion parameters and subjective features. It is assumed that such processing increases naturalness and quality of motion, which is verified by subjective evaluation tests. First, reference motion data are gathered utilizing a motion capture system, then these data are reduced...
-
PERFORMANCE OF ENDOSCOPIC IMAGE ANALYSIS ALGORITHMS IN LARGE BOWEL VIDEOS PROCESSING
PublikacjaComputer-assisted endoscopy is a rapidly developing eld of study. Many image anal- ysis algorithms exist, achieving very high rates of eciency at processing single endoscopic images. However, most of them were never tested in processing real-life endoscopic videos. In the article such tests of 16 endoscopy image analysis algorithms are presented and dis- cussed. Tests were performed on two real-life endoscopic videos of a human...
-
Evaluating Asymmetric N-Grams as Spell-Checking Mechanism
PublikacjaTypical approaches to string comparing marks two strings as either different or equal without taking into account any similarity measures. Being able to judge similarity is however required for spelling error corrections, as we want to find the best match for a given word. In this paper we present a bi2quadro-grams method for spelling errors correction. The method proposed uses different n-grams dimension for the source (checked)...
-
Selecting wells for an optimal design of groundwater monitoring network based on monitoring priority map: A Kish Island case study
PublikacjaThis paper presents a novel approach, i.e. a combination of gamma test and monitoring priority map, for optimal design of groundwater monitoring network (GMN) by considering the cumulative effects of industries, human activities, and natural factors on the groundwater quality. The proposed method was successfully applied to design an optimal network for groundwater salinity monitoring on Kish Island, Persian Gulf. The priority...
-
Expedited Optimization of Passive Microwave Devices Using Gradient Search and Principal Directions
PublikacjaOver the recent years, utilization of numerical optimization techniques has become ubiquitous in the design of high-frequency systems, including microwave passive components. The primary reason is that the circuits become increasingly complex to meet ever growing performance demands concerning their electrical performance, additional functionalities, as well as miniaturization. Nonetheless, as reliable evaluation of microwave device...
-
Model studies to identify input parameters of an algorithm controlling electric supply/consumption process by underground iron ore enterprises
PublikacjaPurpose is the development of the research format of a mathematical model to select and assess input parameters of an algorithm controlling distribution of electric energy flows in the monitoring structure of electricity supply/ consumption by using equipment of mining enterprises engaged in underground iron ore raw materials extraction. Methods. The analytical research involved a theory of random processes adapted to the real...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublikacjaGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Analysis of the applicability of laser scanning to making an inventory of swimming pool facilities
Publikacja3D scanning can be used in many branches of economy, e.g. reverse and prototype engineering, industrial design, quality control, pros-thetics, orthodontics, archiving of historic objects and archeological findings, examination of a scene of crime, making films and comput-er games. The technology of terrestrial laser scanning has a bright fu-ture as we are living in the time of blooming measurement tech-niques, which can provide...
-
Using Synchronously Registered Biosignals Dataset for Teaching Basics of Medical Data Analysis – Case Study
PublikacjaMedical data analysis and processing strongly relies on the data quality itself. The correct data registration allows many unnecessary steps in data processing to be avoided. Moreover, it takes a certain amount of experience to acquire data that can produce replicable results. Because consistency is crucial in the teaching process, students have access to pre-recorded real data without the necessity of using additional equipment...
-
Characterization of herbal teas containing lime flowers – Tiliae flos by HPTLC method with chemometric analysis
PublikacjaLinden trees are a source of food products called lime flowers (Tiliae flos), traditionally used in the form of infusion for the treatment of feverish colds and coughs. Lime flowers should include flowers of Tilia cordata Mill, T.x europaea L., and T. platyphyllos Scop. or a mixture of these. The aim of current research was to establish a fast, sensitive HPTLC (high-performance thin-layer chromatography) method that would allow...
-
Molecular Strategy for Survival at a Critical High Temperature in Eschierichia coli
PublikacjaThe molecular mechanism supporting survival at a critical high temperature (CHT) in Escherichia coli was investigated. Genome-wide screening with a single-gene knockout library provided a list of genes indispensable for growth at 47°C, called thermotolerant genes. Genes for which expression was affected by exposure to CHT were identified by DNA chip analysis. Unexpectedly, the former contents did not overlap with the latter except...
-
THE RISE OF FISCAL OPACITY IN POLAND IN THE ERA OF THE COVID-19 PANDEMIC
PublikacjaResearch background: The quality of information provided by the fiscal authorities and the correct flow of this information between them and the society are very important especially in times of crisis, when there is an imbalance in public finances and an increasing public debt. Ensuring fiscal transparency (transparency of public finances) reduces fiscal risk and corruption and supports public acceptance of fiscal reforms. Purpose...
-
Fine-Tuning the Photocatalytic Activity of the Anatase {1 0 1} Facet through Dopant-Controlled Reduction of the Spontaneously Present Donor State Density
PublikacjaThe present study highlights the importance of the net density of charge carriers at the ground state on photocatalytic activity of the faceted particles, which can be seen as a highly underexplored problem. To investigate it in detail, we have systematically doped {1 0 1} enclosed anatase nanoparticles with Gd3+ ions to manipulate the charge carrier concentration. Furthermore, control experiments using an analogical Nb5+ doped...
-
Rapid Variable-Resolution Parameter Tuning of Antenna Structures Using Frequency-Based Regularization and Sparse Sensitivity Updates
PublikacjaGeometry parameter tuning is an inherent part of antenna design process. While most often performed in a local sense, it still entails considerable computational expenses when carried out at the level of full-wave electromagnetic (EM) simulation models. Moreover, the optimization outcome may be impaired if good initial design is not available. This paper proposes a novel approach to fast and improved-reliability gradient-based...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublikacjaWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Multimodal system for diagnosis and polysensory stimulation of subjects with communication disorders
PublikacjaAn experimental multimodal system, designed for polysensory diagnosis and stimulation of persons with impaired communication skills or even non-communicative subjects is presented. The user interface includes an eye tracking device and the EEG monitoring of the subject. Furthermore, the system consists of a device for objective hearing testing and an autostereoscopic projection system designed to stimulate subjects through their...
-
Dobór parametrów silnika indukcyjnego dużej mocy
PublikacjaW artykule przedstawiono trzy typy statycznych modeli matematycznych silników klatkowych oraz metodę estymacji parametrów, przy wykorzystaniu algorytmów genetycznych. Korzystając z kryteriów: suma kwadratów, suma wartości bez-względnych oraz całkowego, oceniono przydatność badanych modeli. Opracowane modele matematyczne zostały wykorzystane przy doborze algorytmów sterownia sterów strumieniowych. Po-kazano metodykę doboru parametrów...
-
EM-driven topology evolution for bandwidth enhancement of hybrid quadrature patch couplers
PublikacjaA broad operational bandwidth is one of the key performance figures of hybrid patch couplers. Due to the lack of systematic design procedures, bandwidth enhancement is normally obtained through manual modifications of the structure geometry. In this work, an optimization-based topology evolution for EM-driven design of patch couplers with enhanced bandwidth has been proposed. The method exploits a novel spline-based EM model where...
-
Analiza działania rozszerzonego obserwatora prędkości w szerokim zakresie zmian prędkości maszyny indukcyjnej
PublikacjaW artykule przedstawiono zagadnienia związane z odtwarzaniem zmiennych stanu maszyny indukcyjnej. Wykorzystano obserwator oparty na modelu matematycznym maszyny z dodatkowymi zmiennymi. Przedstawiono macierz stanu zlinearyzowanych równań błędu odtwarzania. Opisano sposób definiowania wyznacznika jakości na podstawie rozkładu biegunów obserwatora. Zaproponowano metodę korekcji wzmocnień wraz ze zmianą warunków pracy maszyny. Wykazano...
-
Wieloobszarowa rozmyta regulacja PID mocy reaktora jądrowego
PublikacjaW artykule przedstawiono wieloobszarowy regulator rozmyty z lokalnymi regulatorami PID dla sterowania mocą reaktora jądrowego typu PWR. Wykorzystano model matematyczny o parametrach skupionych reaktora PWR obejmujący procesy generacji i wymiany ciepła oraz efektów reaktywnościowych. Nastawy lokalnych regulatorów PID zostały dobrane w sposób optymalny, minimalizując całkowy wskaźnik jakości ISE. Na przykładzie pokazano że zastosowane...
-
The protection and monitoring of a distribution piping network for potable water supply
PublikacjaPurpose – The purpose of this paper is to implement the corrosion protection method for steel pipes used in a municipal water-pipe network. Results of an inhibitor protection system installed on the system are presented. Inhibitor protection was required due to the high corrosivity of the water collected by a surface intake, which had resulted in a large number of failures and low water quality, due to the presence of corrosion...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublikacjaIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Genetic Algorithm Approach for Gains Selection of Induction Machine Extended Speed Observer
PublikacjaThe subject of this paper is gains selection of an extended induction machine speed observer. A high number of gains makes manual gains selection difficult and due to nonlinear equations of the observer, well-known methods of gains selection for linear systems cannot be applied. A method based on genetic algorithms has been proposed instead. Such an approach requires multiple fitness function calls; therefore, using a quality index...
-
Friction Stir Welding of Aluminum in the Aerospace Industry: The Current Progress and State-of-the-Art Review
PublikacjaThe use of the friction stir welding (FSW) process as a relatively new solid-state welding technology in the aerospace industry has pushed forward several developments in different related aspects of this strategic industry. In terms of the FSW process itself, due to the geometric limitations involved in the conventional FSW process, many variants have been required over time to suit the different types of geometries and structures,...