Wyniki wyszukiwania dla: FORMING OF HIGH-POWER IMPULSES
-
Physical properties of homogeneous TiO2 films prepared by high power impulse magnetron sputtering as a function of crystallographic phase and nanostructure
PublikacjaOptical, photo-electrochemical, crystallographic and morphological properties of TiO2 thin films prepared by high power impulse magnetron sputtering at low substrate temperatures (<65 ◦C) without post-deposition thermal annealing are studied. The film composition-anatase, rutile or amorphous TiO2-is adjusted by the pressure (p ∼ 0.75-15 Pa) in the deposition chamber. The different crystallographic phases were determined with grazing...
-
Issues of Estimating the Maximum Distributed Generation at High Wind Power Participation
PublikacjaThis paper presents the methods of estimating the maximum power that can be connected to the power system in distributed generation sources. Wind turbine generator systems (WTGS) were selected as the subject for analysis. Nonetheless, the considerations presented in this paper are only general and also apply to other types of power sources, including the sources that are not considered part of distributed generation.
-
The effect of cable duct diameter on the ampacity of high-voltage power cables
PublikacjaThe ampacity of power cables depends, among others, on the conditions of heat dissipation from the cable to the environment. Cables are usually laid directly in the ground, but in some sections, they may be placed in ducts, which adversely affects the ampacity of the cable line. The paper presents heat transfer phenomena for cables installed in pipe-type ducts filled with air. The effect of cable duct diameter on this ampacity...
-
Power of the low alpha brainwaves in the mental imagery experiment in sport: the "Start in High Level Championship" scenario.
Dane BadawczeThe data were collected to perform research on the neural oscillation during mental imagery in sport. The main aim of the study was to examine the cortical correlates of imagery depending on instructional modality (guided vs self-produced) using various sport-related scripts. The research was based on the EEG signals recorded during the session with...
-
Qiangjiguang Yu Lizishu/High Power Laser and Particle Beams
Czasopisma -
Effect of mid-frequency discharge assistance on dual-high power impulse magnetron sputtering
Publikacja -
A Combined TOPSIS and FA Based Strategic Analysis of Technical Condition of High Power Transformers
PublikacjaThe paper presents mathematical model { TOPSIS method, which was utilized on insulating state of distribution transformer to analyze and sensibility of individual measurements methods mutual comparison. We can uniquely determine the importance of these measurements methods with this mathematical appara- tus in these measurements methods in insulating state of transformers.
-
Case studies of resonance phenomena in high voltage overhead power lines with shunt reactors
PublikacjaMisguided design of the towers of power transmission lines can lead to serious problems such as voltage asymmetry, overvoltages, electric arc extinction difficulties or resonance – in case of double circuit line with shunt reactors. The paper points out those threats on example of 400 kV double circuit overhead transmission line with shunt reactors.
-
Determination of Complex Permeability of Silicon Steel for Use in High-Frequency Modeling of Power Transformers
Publikacja -
Design of high frequency OTA in 130nm CMOS technology with single 1.2v power supply
PublikacjaW artykule przedstawiono wzmacniacz transkonduktancyjny OTA zasilany niskim napięciem i przeznaczony do użycia w filtrach czasu ciągłego w zakresie wysokich częstotliwości przetwarzanych sygnałów. Stopień wejściowy zbudowany jest w oparciu o inwertery CMOS. Wartość transkonduktancji wzmacniacza jest przestrajana z wykorzystaniem efektu podłożowego tranzystorów. Omówiono również układ dostrajania wzmacniacza. Brak wewnętrznych węzłów...
-
Evaluation of selected diagnostic variables for the purpose of assessing the ageing effects in high-power IGBTs
PublikacjaPrzedstawiono metodę wyznaczania dwóch wskaźników diagnostycznych, które mogą być używane do oceny zużycia modułów IGBT dużej mocy. Proponowane podejście jest próbą zaadaptowania znanej z literatury metody laboratoryjnej do pracy bezpośrednio w układzie napędowym pojazdu trakcyjnego. Rozważane wskaźniki diagnostyczne to rezystancja cieplna między półprzewodnikiem a podstawą modułu oraz napięcie nasycenia kolektor-emiter IGBT....
-
The Evaluation of Quality of the Co-Firing Process of Glycerine Fraction with Coal in the High Power Boiler
Publikacja -
Could graphene construct an effective conducting network in a high-power lithium ion battery?
Publikacja -
Highly Oriented Zirconium Nitride and Oxynitride Coatings Deposited via High‐Power Impulse Magnetron Sputtering: Crystal‐Facet‐Driven Corrosion Behavior in Domestic Wastewater
PublikacjaHerein, highly crystalline ZrxNy and ZrxNyOz coatings are achieved by the deposition via high‐power impulse magnetron sputtering. Various N2 and N2/O2 gas mixtures with argon are investigated. The chemical composition and, as a result, mechanical properties of the deposited layer can be tailored along with morphological and crystallographic structural changes. The corrosion resistance behavior is studied by potentiodynamic measurements...
-
Dynamic Study of Dual High-Power Impulse Magnetron Sputtering Discharge by Optical Emission Imaging
Publikacja -
Effect of nitrogen doping on TiOxNythin film formation at reactive high-power pulsed magnetron sputtering
Publikacja -
Some coatings of high cavitation resistance produced by CO2 laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono wyniki badań odporności kawitacyjnej stali 2H13, 45 i żelaza Armco po laserowym stopowaniu ich powierzchni różnymi kompozycjami proszków Co, Mo, Ni, Mn i Cr, Ti. Wykazano różne własności kawitacyjne otrzymanych warstw w zależności od otrzymanej mikrostruktury.
-
Hybrid high-frequency-SiC and line-frequency-Si based PEBB for MV modular power converters
PublikacjaIzolowane przekształtniki DC-DC o sterowanym kącie przesunięcia napięć strony pierwotnej i wtórnej są kluczowymi elementami współczesnych modułowych przekształtników energoelektronicznych średniego napięcia (SN). W porównaniu do konwencjonalnych przekształtników SN, przekształtniki modułowe z izolowanymi przetwornicami DC-DC nie wymagają izolacji w postaci wielkogabarytowych transformatorów o częstotliwości sieci. Zastosowanie...
-
Magnetic and capacitive couplings influence on power losses in double circuit high voltage overhead transmission line
PublikacjaPurpose – The paper aims to discuss problems of power and energy losses in a double-circuit overhead transmission line. It was observed from energymeters’ readings, that in such a line, active power losses can be measured as “negative”. The “negative” active power losses appear when the active power injected to the circuit is lower than the active power received at the circuit end. The purpose of this paper is to explain this phenomenon. Theoretical...
-
Modelling of the High Speed Multi-Pole Synchronous Generator for Application in More Electric Aircraft Power Systems
PublikacjaIn this paper different models of the synchronous generator are presented. The simulation results compared with the measurements are shown. Certain physical phenomena are included in described models for the porpoise of adequate analysis of the more electric aircraft power system. For different modelling levels, such as functional level or behavioural level, different physical phenomena have been included. Simulation results for...
-
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publikacja -
Enabling a Stable High-Power Lithium-Bromine Flow Battery Using Task-Specific Ionic Liquids
Publikacja -
Physical properties of homogeneous TiO2films prepared by high power impulse magnetron sputtering as a function of crystallographic phase and nanostructure
Publikacja -
Mechanical and Thermal Properties of W-Ta-B Coatings Deposited by High-Power Impulse Magnetron Sputtering (HiPIMS)
Publikacja -
DEPO: A dynamic energy‐performance optimizer tool for automatic power capping for energy efficient high‐performance computing
PublikacjaIn the article we propose an automatic power capping software tool DEPO that allows one to perform runtime optimization of performance and energy related metrics. For an assumed application model with an initialization phase followed by a running phase with uniform compute and memory intensity, the tool performs automatic tuning engaging one of the two exploration algorithms—linear search (LS) and golden section search (GSS), finds...
-
Plasma diagnostics of low pressure high power impulse magnetron sputtering assisted by electron cyclotron wave resonance plasma
Publikacja -
Cavitation resistance of OH18N9 steel alloyed with vaidus amount of TiC or Mn by means of laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali OH18N9T po laserowym stopowaniu jej powierzchni węglikiem TiC oraz manganem. Wykazano, że wzbogacenie obrabianej stali manganem powoduje przemiany fazowe pod wpływem działania obciążeń kawitacyjnych, co przyczynia się do wzrostu odporności kawitacyjnej. Wzmacnianie stali węglikiem TiC powoduje natomiast zanik zdolności stali do wzmacniania odkształceniowego.
-
High frequency test measurements on physical model of power transformer with use of FRAX analyzer Streszczenie. W niniejszym artykule przedstawiono pomiary testowe SFRA wykonane na modelu fizycznym transformatora elektroenergetycznego
Publikacja -
Karolina Lademann mgr
OsobyCurriculum vitae
-
Influence of span length and impulse front time on earthing measurement accuracy of power line towers
PublikacjaThe article discusses the issue of measuring and assessing the features of power line tower earthings using fast-changing waveform. The study analyses the effect of impulse front time and the line span length on errors made during these measurements using impulse meters. It has been found that the assessment conditions similar to the static measurement results occur for the use of 4 μs current impulses and such procedure is useful...
-
Michał Michna dr hab. inż.
OsobyJest absolwentem Wydziału Elektrycznego Politechniki Gdańskiej (1998). W 2004 r. uzyskał stopień doktora. Od 2004 r. zatrudniony w Katedrze Energoelektroniki i Maszyn Elektrycznych Politechniki Gdańskiej (asystent, adiunkt, starszy wykładowca). W latach 2010-2015 zastępca kierownik katedry. Jego zainteresowania naukowe i dydaktyczne obejmują szerokie spektrum zagadnień związanych z projektowanie, modelowanie i diagnostyką maszyn...
-
Technology and Energy Conversion Machines - Nowy
Kursy OnlineThe course covers the basics of mechanical, electrical and thermal energy production in industry and maritime transport. Describes installations supporting high-power engines. Particular attention has been paid to the fuel systems of internal combustion engines. The treatment of engine exhaust gases is described.
-
Technology and Energy Conversion Machines - Nowy kopiuj 1
Kursy OnlineThe course covers the basics of mechanical, electrical and thermal energy production in industry and maritime transport. Describes installations supporting high-power engines. Particular attention has been paid to the fuel systems of internal combustion engines. The treatment of engine exhaust gases is described.
-
Application of Multivariate Adaptive Regression Splines (MARSplines) Methodology for Screening of Dicarboxylic Acids Cocrystal Using 1D and 2D Molecular Descriptors
PublikacjaDicarboxylic acids (DiAs) are probably one of the most popular cocrystals formers. Due to the high hydrophilicity and non-toxicity, they are promising solubilizes of active pharmaceutical ingredients (APIs). Although DiAs appear to be highly capable of forming multicomponent crystals with various compounds, some systems reported in the literature are physical mixtures the solid state without forming stable intermolecular complex....
-
Technology and Energy Conversion Machines
Kursy OnlineThe course covers the basics of mechanical, electrical and thermal energy production in industry and maritime transport. Describes installations supporting high-power engines. Particular attention has been paid to the fuel systems of internal combustion engines. The treatment of engine exhaust gases is described.
-
Jerzy Konorski dr hab. inż.
OsobyJerzy Konorski otrzymał tytuł mgr inż. telekomunikacji na Poitechnice Gdańskiej, zaś stopień doktora n.t. w dyscyplinie informatyka w Instytucie Podstaw Informatyki PAN. W r. 2007 obronił rozprawę habilitacyjną na Wydziale Elektroniki, Telekomnikacji i Informatyki PG. Jest autorem ponad 150 publikacji naukowych, prowadził projekty naukowo-badawcze finansowane ze środków Komitetu Badań Naukowych, UE, US Air Force Office of Scientific...
-
Current divider-based nanosecond high current pulse measuring systems
PublikacjaThis paper presents the analysis of the new approach to the measurement methodology of significant values (in order of hundreds of kA) and huge steepness (in order of MA/μs) current pulses based on current dividers along with a comparison of the various types transducers suitability in measuring systems with such extreme parameters. Such dividers are used to extend the measurement ranges of current transducers with limited current...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Comparison of experimental and numerical results on metallic plates subjected to explosions
PublikacjaA comparative study of dynamic response including damage and rupture processes of thin metallic plates subjected to shockwave impulses - explosions is presented. The results of the finite element numerical analysis are related to experiments. Due to high strain rate during explosions the elasto-viscoplastic Chaboches constitutive law including damage effects has been applied. For the assumed model proper material parameters identification...
-
Enhanced Charge Storage Mechanism And Long-Term Cycling Stability In Diamondized Titania Nanocomposite Supercapacitors Operating In Aqueous Electrolytes
PublikacjaThe long cycle life stability jointly with high energy density are limiting broader feasible applications of supercapacitors. The novel diamondized titania nanocomposite supercapacitors deliver high power and energy densities along with high capacitance retention rates. Supercapacitor electrodes were fabricated utilizing a combination of Ti anodization followed by chemical vapor deposition resulting in simultaneous growth of complex...
-
Piotr Dworakowski dr
OsobyPiotr Dworakowski received the MSc degree and PhD degree with distinction in electrical engineering from Gdansk University of Technology, Poland, in 2007 and 2020 respectively. From 2008 to 2013 he was working in Alstom Transport, Tarbes, France on traction drives control. Since 2014 he has been a Power Converters Team Leader in SuperGrid Institute, Lyon, France. His research interests include high efficiency power converters for...
-
Waldemar Korłub dr inż.
OsobyWaldemar Korłub uzyskał tytuł inżyniera w 2011 roku, tytuł magistra w 2012 roku oraz stopień doktora w dyscyplinie informatyki w 2017 roku na Wydziale Elektroniki Telekomunikacji i Informatyki Politechniki Gdańskiej. Jego zainteresowania naukowe obejmują: systemy rozproszone ze szczególnym uwzględnieniem systemów typu grid i chmur obliczeniowych, systemy autonomiczne zdolne do samodzielnej optymalizacji, zarządzania zasobami, ochrony...
-
Karol Grębowski dr inż.
OsobyKarol Grębowski (dr inż.) pracuje jako adiunkt w Katedrze Technicznych Podstaw Projektowania Architektonicznego na Wydziale Architektury Politechniki Gdańskiej. Jego badania naukowe dotyczą zjawisk szybkozmiennych zachodzących podczas drgań konstrukcji budowlanych, obiektów mostowych (trzęsienia ziemi) oraz badania w zakresie metodologii projektowania budynków stanowiących system ochrony pasywnej (SOP) odpornych na uderzenia pojazdów...
-
Fault detection in measuring systems of power plants
PublikacjaThis paper describes possibility of forming diagnostic relations based on application of the artifical neural networks (ANNs), intended for the identifying of degradation of measuring instruments used in developed power systems. As an example a steam turbine high-power plant was used. And, simulative calculations were applied to forming diagnostic neural relations. Both degradation of the measuring instruments and simultaneously...
-
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublikacjaChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
Jerzy Proficz dr hab. inż.
OsobyJerzy Proficz – dyrektor Centrum Informatycznego Trójmiejskiej Akademickiej Sieci Komputerowej (CI TASK) na Politechnice Gdańskiej. Uzyskał stopień naukowy doktora habilitowanego (2022) w dyscyplinie: Informatyka techniczna i telekomunikacja. Autor i współautor ponad 50 artykułów w czasopismach i na konferencjach naukowych związanych głównie z równoległym przetwarzaniem danych na komputerach dużej mocy (HPC, chmura obliczeniowa). Udział...
-
Start-up of a power unit of a thermal power plant auxiliary systems with supply from a hydropower plant
PublikacjaThis article discusses the issues related to a power unit of a thermal power plant start-up with the use of a hydropower plant. Hydropower plant can supply and will enable start-up of auxiliary equipment in a power unit of a thermal power plant. Due to high capacity of auxiliary drives, start-up of auxiliaries in a thermal power plant after blackout (and boiler shutdown) is not possible from emergency energy sources in the power...
-
Excitation of Non-Wave Modes by Sound of Arbitrary Frequency in a Chemically Reacting Gas
PublikacjaThe nonlinear phenomena in the field of high intensity sound propagating in a gas with a chemical reaction, are considered. A chemical reaction of A → B type is followed by dispersion and attenuation of sound which may be atypical during irreversible thermodynamic processes under some conditions. The first and second order derivatives of heat produced in the chemical reaction evaluated at the equilibrium temperature, density and...
-
Selection Of Optimal Working Fluid For Use With Hybrid Microchannel-Microjet Heat Exchanger
PublikacjaThe paper presents the investigation to find best suited working fluid for a microjet- microchannel cooling module. In which microjets are impinging into the microchannels and forming a liquid film on the impingement surface. This technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels...