Wyszukiwarka
Wyniki wyszukiwania dla: SLOPE, STABILITY, ACCELERATION, VERTICAL COMPONENT, ACCELEROMETER, PERMANENT DISPLACEMENT
-
Experimental study of the effect of vertical acceleration component on the slope stability
PublikacjaThe paper deals with the stability of earth dams subjected to seismic and paraseismic excitations occurring in the close distance to the dam. The Newmark’s stability approach, classified as a simplified dynamic method, has been extended for two directional dynamic loading case and the evolution of the friction coefficient. The paper is focused on the experimental verification of the proposed method for harmonic and cyclic excitations...
-
Extended Newmark method to assess stability of slope under bidirectional seismic loading
PublikacjaThe paper concerns the dynamic behavior of a simple slope model subjected to simultaneous horizontal and vertical excitations. The proposed method is based on Newmark’s sliding block concept, however, four new features are introduced. The most important assumption is that the normal component of dynamic excitations affects the resisting force both before and after the initiation of the relative slope motion, making it time-dependent....
-
Effect of excitation intensity on slope stability assessed by a simplified approach
PublikacjaThe paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes...
-
Multifunctional Bandpass Filter/Displacement Sensor Component
PublikacjaThis paper presents the design and realization of a multifunctional bandpassfilter/displacement-sensor using an edge-coupled microstrip bandpass filter loaded by a pair of split ring resonators (SRRs). It is shown that while the structure acts as a bandpass filter at its operating frequency, the phase of the reflection coefficient from a movable loading resonator at the resonance frequency of the resonator can be used for displacement...
-
STABILITY OF THE INNER SLOPE OF THE POLISH DREDGDIKES RESEARCH DIKE AT STATIONARY FLOW
PublikacjaFor long duration of the flood the water table can appear on the slope with a problem of out-wash in the case of sand type dike. If the dike corps is covered with less permeable layer some additional push-off forces and shearing can rise in the cover. In both cases the micro stability of the inner slope should be considered at normative high water for homogeneous sand type dike or sand type dike with less permeable covers. The...
-
Low speed permanent magnet synchronous generator for vertical axis wind turbine
PublikacjaThe paper presents design process and tests of a prototype low speed permanent magnet synchronous generator (PMSG) dedicated for the innovative vertical-axis wind turbine. The rated data of the designed generator are following: power - 15 kVA, voltage - 400 V (Y), rotation speed - 93.75 rpm. The design assumptions, chosen results of the design process and experimental tests of the prototype PMSG are presented. The considered PMSG...
-
Simplified stability analysis of steel cylindrical silos with corrugated walls and vertical columns
PublikacjaIn the paper a simplified stability analysis of steel cylindrical silos composed of corru¬gated walls and vertical open-sectional columns was proposed. The whole 3D silo was modeled as a single column resting on elastic foundation provided by the silo walls. In proposed formula for the calculation of the foundation stiffness the curvature of the silo walls was taken into account. Three different analyses were carried out using...
-
Investigations of transverse stability of semi-displacement ships
PublikacjaPrzedstawiono wyniki eksperymentalnych badań modelowych poprzecznej stateczności jednostek półślizgowych, których celem było określenie wpływu prędkości oraz parametrów kształtu kadłuba na stateczność poprzeczną. Na podstawie wyników badań opracowano algorytmy, uwzględniające zmiany ramienia prostującego w funkcji prędkości, kąta przechyłu i parametrów geometrycznych kadłuba które mogą być wykorzystane do oceny stateczności poprzecznej...
-
GNSS reference solution for permanent sition stability monitoring and geodynamical investigations - the ASG-EUPOS case study
PublikacjaThe aim of this paper is to present the strategy of determination of the reference solution for the ASG-EUPOS (ActiveGeodetic Network – European Position Determination System) coordinate monitoring system. ASG-EUPOS is a network of permanent GNSS (Global Navigation Satellite System) stations controlled by the Polish Head Office of Geodesy and Cartography (HOGC), which main role is to realize the ETRS89 (European Terrestrial Reference...
-
Slope Stability Analysis of Zoned Earth Dam with RCC Overtopping Protection
Publikacja -
Reliability Analysis of Sea Cliff Slope Stability by Point Estimate Method
PublikacjaThe paper presents a reliability analysis of a sea cliff slope. The cliff, located in Jastrzębia Góra, is characterised by a complicated geological structure. Although currently stable, it is in fact close to the limit state. The objective of this paper is to present the point estimate method (PEM) of determining the mean value and standard deviation of the safety factor of the slope. Assuming its normal distribution, these statistical...
-
Reliability Analysis of Sea Cliff Slope Stability by Point Estimate Method
PublikacjaThe paper presents a reliability analysis of a sea cliff slope. The cliff, located in Jastrzębia Góra, is characterised by a complicated geological structure. Although currently stable, it is in fact close to the limit state. The objective of this paper is to present the point estimate method (PEM) of determining the mean value and standard deviation of the safety factor of the slope. Assuming its normal distribution, these statistical...
-
Measurements of displacement and acceleration of the railway bridge at km 333-254 of the Vilnius - Klaipeda railway line
PublikacjaThe purpose of this work is to perform a report of static and dynamic test realized on the bridge at km 333-254 of the Vilnius - Klaipeda railway line over the Salantas River in Kūlupėnų.
-
Stability of an optical displacement sensor using a two-beam polarization interferometer
PublikacjaW artykule przedstawiono wyniki pomiarów stabilności wybranej konfiguracji dwuwiązkowego interferometru polaryzacyjnego. Przedyskutowano źródła występującej niestabilności.
-
Effect of water infiltration through concrete block spillways on the slope stability of earth overflow dams
Publikacja -
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublikacjaThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Stability and initial post-buckling behaviour of frame system with vertical bracings
PublikacjaStalowe hale są budowane jako układ ram płaskich połączonych stężeniami dachowymi i stężeniami pionowymi w postaci krzyżujących się prętów. W pracy przedstawiono analizę stateczności i zachowania pokrytycznego takiego układu poddanego działaniu obciążeń pionowych. Korzystając z warunków stacjonarności całkowitej energii potencjalnej wykazano, że punkt bifurkacji utraty stateczności jest niesymetryczny i niestateczny. Oznacza to,...
-
Simplified numerical model for global stability of corrugated silos with vertical stiffeners
PublikacjaArtykuł omawia wyniki stateczności globalnej silosów z blachy falistej z pionowymi usztywnieniami. Zaproponowano uproszczony model numeryczny metody elementów skończonych do określenia stateczności. Wyniki numeryczne były bardziej dokładnie niż metody zaproponowane w Eurokodzie.
-
GNSS reference solution for permanent station stability monitoring and geodynamical investigations: the ASG-EUPOS case study.
Publikacja.
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublikacjaAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
Critical assessment of Eurocode approach to stability of metal cylindrical silos with corrugated walls and vertical stiffeners.
PublikacjaPrzedmiotem artykułu było krytyczne oszacowanie podejścia w Eurokodzie odnośnie stateczności metalowych cylindrycznych silosów z blachy falistej i słupów. Obliczenia 3D wykonane stosując MES. Symulowano blachę gładką ze słupami belkowymi o zastępczej sztywności. W obliczeniach uwzględniono falistość blachy. Pokazano, że wzory normowe znacznie odbiegają od wyników MES.
-
Stability analysis of the internal cylindrical shell wall of a vertical double shell tank under a water test.
PublikacjaPrzedstawiono analizę zagrożenia stateczności lokalnej płaszcza wewnętrznego przy różnicy poziomów wody w zbiorniku wewnętrznym i przestrzeni międzypłaszczowej podczas próby wodnej zbiornika. Podano krytyczne różnice poziomów wody dla typowych zbiorników o pojemności od 10 000 do 100 000 m3.
-
Analysis of the internal shell stability of the cylindrical vertical double-shell tank under the condition of the hydrostatic test
PublikacjaUtrata stateczności płaszcza wewnętrznego w pionowym stalowym zbiorniku może wystąpić jeżeli podczas próby wodnej słup wody w przestrzeni międzypłaszczowej będzie miał większą wysokość niż w zbiorniku wewnętrznym. W artykule przeprowadzono analizę jaka różnica poziomów wody podczas próby wodnej może zagrażać stateczności płaszcza wewnętrznego w zbiorniku o pojemności od 10000 m3 do 100000 m3.
-
Przemysław Krata dr hab. inż.
Osoby -
Enhancement of PUR/PIR foam thermal stability after addition of Zostera marina biomass component investigated via thermal analysis and isoconversional kinetics
PublikacjaIn the present work, a thorough thermogravimetric (TG) analysis of bio-based polyurethane–polyisocyanurate (PUR–PIR) foams in both nitrogen and oxygen atmosphere is performed. A sustainable element of the foam is a biopolyol obtained via acid-catalyzed liquefaction of Zostera marina and Enteromorpha Algae biomass. Based on isoconversional analysis and apparent activation energies, several conclusions are obtained. In contradiction...
-
Wykorzystaniem metody elementów skończonych w obliczaniu stateczności silosu z blachy falistej = Finite element method in determining stability of with corrugated walls strengthened by vertical columns of thin walled open cross section
PublikacjaGwałtowny rozwój zastosowania MES w działalności inżynierskiej nastąpił w połowie lat osiemdziesiątych w związku z pojawieniem się komputerów osobistych (PC), na które przeniesione zostały programy z dużych jednostek obliczeniowych. W ten sposób efektywne narzędzie rozwiązywania problemów analiz i projektowania jakim jest MES, stało się powszechnie dostępne. W artykule przedstawiono zastosowanie MES w analizie stateczności stalowego...
-
Modelling an accelerometer for robot position estimation
PublikacjaThe article describes a new model of a MEMS accelerometer for usage in inertial measurement units (IMU). Such units allow to measure orientation and location of the sensor/system and therefore can be applied for systems positioning. The main purpose of the paper is to model pertinent accelerometer functions substantial in determination of the location of the sensor by means of double integration of acceleration. The model takes...
-
Evaluation of position estimation based on accelerometer data
PublikacjaThe paper concerns the problem of integrating data from accelerometers. A suitable model of a MEMS accelerometer is presented which is a part of inertial measurement units (IMU). Such units allow to measure orientation as well as to localize systems. They also appear to be applicable for systems positioning. The main purpose of the paper is to discuss conditions that must be satisfied to calculate the location of the sensor by...
-
Sieć sensorowa do rejestracji drgań górnej sieci trakcyjnej w celach diagnostyki eksploatacyjnej
PublikacjaWraz ze wzrostem prędkości kolejowych pojazdów elektrycznych zwiększają się wymagania utrzymania sieci trakcyjnej w odpowiednim stanie technicznym. Ciągły monitoring i diagnostyka pozwalają wykrywać pogarszającą się jakość odbioru prądu z sieci jezdnej. Jedną z metod jest umieszczenie czujników przyspieszenia na przewodzie jezdnym. Analiza przebiegu przyspieszenia pozwala określić jakość współpracy sieci jezdnej z pantografem....
-
Magnetic flux leakage signals of near side defects measured with different velocities
Dane BadawczeThe dataset contains raw signals measured with the use of the magnetic flux leakage (MFL) technique. Linear Hall effect sensors A1324 were used to measure magnetic flux leakage. Three voltage signals were measured: Bx sensor output, Bz1 sensor output, and difference of Bz1 and Bz2 outputs. An output of a Bx sensor was directly proportional to the tangential...
-
Magnetic flux leakage signals of far side defects measured with different velocities
Dane BadawczeThe dataset contains raw signals measured with the use of the magnetic flux leakage (MFL) technique. Linear Hall effect sensors A1324 were used to measure magnetic flux leakage. Three voltage signals were measured: Bx sensor output, Bz1 sensor output, and difference of Bz1 and Bz2 outputs. An output of a Bx sensor was directly proportional to the tangential...
-
Hydro and marine civil engineering
Kursy OnlineKurs realizowany na Wydziale Inżynierii Lądowej i Środowiska (WILiŚ) Politechniki Gdańskiej. Studia: II stopnia - magisterskie, stacjonarne Kierunek: Budownictwo Semestr: 1 (letni) Presentation of basic hydro and marine civil engineering structures together with basic computational procedures for determining environmental forces acting on a structure (vertical-wall breakwater, rubble mound breakwater, submarine pipelines...
-
Hydro and marine civil engineering (2020-2021)
Kursy OnlineKurs realizowany na Wydziale Inżynierii Lądowej i Środowiska (WILiŚ) Politechniki Gdańskiej. Studia: II stopnia - magisterskie, stacjonarne Kierunek: Budownictwo Semestr: 1 (letni) Presentation of basic hydro and marine civil engineering structures together with basic computational procedures for determining environmental forces acting on a structure (vertical-wall breakwater, rubble mound breakwater, submarine pipelines...
-
Hydro and marine civil engineering (2021-2022)
Kursy OnlineKurs realizowany na Wydziale Inżynierii Lądowej i Środowiska (WILiŚ) Politechniki Gdańskiej. Studia: II stopnia - magisterskie, stacjonarne Kierunek: Budownictwo Semestr: 1 (letni) Presentation of basic hydro and marine civil engineering structures together with basic computational procedures for determining environmental forces acting on a structure (vertical-wall breakwater, rubble mound breakwater, submarine pipelines...
-
Brief Literature Review and Classification System of Reliability Methods for Evaluating the Stability of Earth Slopes
PublikacjaThe issue of slope stability is one of the most important and yet most difficult geotechnical problems. Assessing slope stability is particularly difficult because of the many uncertainties involved in the process. To take these uncertainties into account, probabilistic methods are used, and the reliability approach is adopted. There are many methods for reliability assessment of earth slope stability. However, there is no system...
-
Investigation of noises in the EPN weekly time series
PublikacjaThe constantly growing needs of permanent stati ons’ velocities users cause their stability level to increase. To this research we included more than 150 stations located across Europe operating within the EUREF Permanent Network (EPN) w ith weekly changes in the ITRF2005 reference frame. The obvious long-range dependencies in the stochastic part of GPS time series were p roven by Ljung-Box...
-
Feasibility Study for Food Intake Tasks Recognition Based on Smart Glasses
PublikacjaIn this exploratory study 13 adult test subjects have performed different food intake tasks while wearing a three axis accelerometer mounted at a temple of glasses. Two different algorithms for task recognition have been applied and compared. The retrospective data processing leads to better task recognition results when the frequency range of 50 Hz to 100 Hz is analysed within accelerometer signal recordings. A straightforward...
-
Evaluating the mobile robot positions using accelerometer data
PublikacjaThis paper analyzes the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...
-
Evaluating the position of a mobile robot using accelerometer data
PublikacjaThis paper analyses the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...
-
DETERMINATION OF VERTICAL DISPLACEMENTS IN RELATIVE MONITORING NETWORKS
PublikacjaThe problem of determining displacements of objects is an important and current issue, in particular in terms of operational safety. This is a requirement that covers geodetic, periodic control measurements in order to determine horizontal and vertical displacements. The paper is focused on the analysis of vertical displacements. Geodetic measurements and their interpretation allow to reduce the risk of possible structural catastrophes....
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublikacjaThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
Scanning Electron Microscopy images of nanocubes suspension 1 month after synthesis
Dane BadawczeThis dataset contains the SEM images of the gold nanocubes suspension in citrate buffer. The goal of the study was to evaluate the size of the synthesized nanocubes, their stability one month after the synthesis process, and to verify the optimal conditions regarding nanocubes concentration for the SEM analysis. Solutions with two different AuNC concentrations...
-
Determination of vertical displacements by using the hydrostatic levelling systems with the variable location of the reference sensor,
PublikacjaAbstract: In this paper, the author proposed a new method for determination of vertical displacements with the use of hydrostatic levelling systems. The traditional method of hydrostatic levelling uses a rule in which a position of reference sensor is stable. This assumption was not adapted in the proposed method. Regarding the issue mentioned above, the reference sensor is treated in the same way as the others sensors that measure...
-
Stability analysis of a road scarp in the Carpathian Mountains and methods of its protection
PublikacjaThe purpose of the study was to analyse the stability of a road scarp endangered by a landslide and to consider some measures for its stabilization. The potential landslide could unfavourably alter the shape of the slope, thus a religious sanctuary situated above the slope. The present research has resulted in suggestions of possible protection methods, namely, drainage, soil nailing, installation of piles, supporting the scarp...
-
Stress-driven nonlocal elasticity for nonlinear vibration characteristics of carbon/boron-nitride hetero-nanotube subject to magneto-thermal environment
PublikacjaStress-driven nonlocal theory of elasticity, in its differential form, is applied to investigate the nonlinear vibrational characteristics of a hetero-nanotube in magneto-thermal environment with the help of finite element method. In order to more precisely deal with the dynamic behavior of size-dependent nanotubes, a two-node beam element with six degrees-of freedom including the nodal values of the deflection, slope and curvature...
-
Zastosowanie nowatorskich materiałów geosyntetycznych w konstrukcjach oporowych z gruntu zbrojonego
PublikacjaArtykuł prezentuje metodę projektowania stromych skarp wznoszonych z gruntów słabo przepuszczalnych, zbrojonych geosiatkami drenującymi. Z analiz przeprowadzonych dla różnej wodoprzepuszczalności gruntu i różnej geometrii skarpy wynika, że pionowy rozstaw i długość zbrojenia mają istotne znaczenie dla stateczności skarpy. Dla gruntów słabo przepuszczalnych, o typowych wartościach współczynników ściśliwości objętościowej oraz konsolidacji,...
-
Hybrid Model of Axially Moving Continua
PublikacjaThe paper introduces the method of the model reduction of systems that experience a Coriolis acceleration component. It causes that system equations are non-self-adjoined. To avoid such problem modal, reduced model is built up for the system without Coriolis acceleration terms which are next included by application of any lumping technique. Hence, the final reduced model is a hybrid one, obtained by both lumping and modal methods...
-
Geotechnical Analysis and Stability Assessment of a Landslide Event in Gera Woreda, Ethiopia
PublikacjaThis study investigates the geotechnical factors influencing a recent landslide event in Gera Woreda, Ethiopia. The primary objective was to identify the soil properties contributing to landslide occurrence and understand the triggering mechanisms. Field investigations, soil sampling from both affected and unaffected areas, and subsequent laboratory characterization were conducted. The analysis revealed a dominance of fine-grained...
-
Modal Reduction and Analysis of Gyroscopic Systems
PublikacjaThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
Analysis of the process of water entry of an amphibious vehicle
PublikacjaThe paper presents a method of computational and experimental analysis of the process of water entry of an amphibious vehicle. The computational method is based on the Reynolds Averaged Navier-Stokes Equations (RANSE) solver and the xperiment was carried out in the towing tank at Ship Design and Research Centre S.A. with the use of a scale model. The analysis was focused on the safety of water entry, i.e. the maximum pitch and...