Wyszukiwarka
Wyniki wyszukiwania dla: mechanical vibrations
-
The analysis of mechanical vibrations with use of the MATHCAD.
PublikacjaPrzedstawiono zagadnienie analizy drgań mechanicznych ze wspomaganiem komputerowym za pomocą programu MATHCAD. Omówiono zagadnienia zastosowania programu w edukacji i w obliczeniach inżynierskich.
-
Stability evaluation of the marine propulsion unit mechanical system bymeans of vibrations measurements and their analysis.
PublikacjaIn paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been given. The analysis of vibration parameters was carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration's level had been observed. In the beginning, the vibration apparatus being on laboratory equipment of the Department of Ship Power Plants of...
-
Sounding rocket vibration mechanical filter and amplifier
PublikacjaMeasuring accelerations and vibrations of a sounding rocket provides both information for engineers on the launcher vehicle performance as well as environment description for future payload designers. Typically, information on the level of vibration and eigenfrequencies are required to properly design a payload. This paper presents a design of a novel mechanical filter and amplifier for mechanical vibrations. Its key feature is...
-
Forced vibrations in a dynamic system that is damped by a mechanism that trans-pass through its singular position
PublikacjaIn the paper, vibrations of a hybrid multibody-continuous system are investigated. For all the mechanical devices, effective damping methods are crucial in the design process. To obtain it, installation of viscous dampers or elasto-viscous elements is dominant. In the paper, an alternative method is investigated. It is based on modal disparity. To describe the method briefly, when structural damping is present in continuous systems,...
-
Stability evaluation of the marine propulsion unit's mechanical system by means of vibration measurements and their analysis
PublikacjaIn this paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been given. The analysis of vibration parameters was carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration's level had been observed. In the beginning, the vibration apparatus being on laboratory equipment of the Department of Ship Power Plants...
-
Rigid finite elements and multibody modelling used in estimation and reduction of rod vibrations
PublikacjaIn the paper, a mechanical set composed of a robot (manipulator) and of an elastic beam is considered. The beam is fixed to the top of the robot structure. In most of the similar cases, undesired vibrations can be excited in the beam. They are especially significant, when dynamics in the robot braking period is examined. In the paper, estimation and modification of length of the braking period is proposed, in order to reduce the...
-
The influence of external interference on AFM imaging, the use of a protective helmet
Dane BadawczeThis collection is of purely practical importance, showing how the presence of external disturbances can adversely affect the quality of imaging with an atomic force microscope. For this reason, it is also advisable to provide a link to a workshop-like study [1] as well as a huge number of commercial solutions available after entering the keyword "AFM...
-
Adam Dąbrowski dr inż.
OsobyAdam Dąbrowski uzyskał stopień doktora nauk inżynieryjno-technicznych w dyscyplinie inżynieria mechaniczna na Politechnice Gdańskiej oraz ukończył studia II stopnia na kierunku mechatronika na Technische Universität Hamburg a także double degree Engineering and Management of Space Systems na Hochschule Bremen. Posiada doświadczenie przemysłowe (Instytut Lotnictwa w Warszawie, SICK AG w Hamburgu, Blue Dot Solutions w Gdańsku, Niemieckie...
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Dane BadawczeTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Diagnostic testing of marine propulsion systems with internal combustion engines by means of vibration measurement and results analysis
PublikacjaIn this paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been presented, carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration’s level had been observed. Used diagnosing system has been characterised. A procedure of longitudinal and transverse vibrations shaft lines of the mechanical system within...
-
Forced Vibrations in a Dynamic System That Is Damped By a Mechanism Which Trans-Pass Through Its Singular Position
PublikacjaThe paper focuses on forced vibrations of a mechanical system. The system is composed of two structurally different parts: multibody modelled and finite elements modelled. To improve its numerical behaviour, author-proposed technique of tuning of modal properties is proposed. To combine the two sub-models, constraint equations are introduced and dynamics equations are extended with appropriate Lagrange multipliers. A slightly modified...
-
Detection of the acoustic interferences during AFM operation
Dane BadawczeAtomic force microscopy is a particularly complicated surface imaging technique due to the large number of factors that affect the quality of the resulting images. They are obviously difficult and sometimes even impossible to control at the same time. One of such factors may even be the seismological location of the building or the influence of mechanical...
-
Natalia Stawicka-Morawska dr inż.
OsobyMgr inż. Natalia Stawicka-Morawska pracuje na Politechnice Gdańskiej od października 2017 r. na stanowisku Asystenta, na Wydziale Inżynierii Mechanicznej i Okrętownictwa (poprzednio: Wydziale Mechanicznym), w Instytucie Mechaniki i Konstrukcji Maszyn (poprzednio: Katedrze Mechaniki i Mechatroniki).Prowadzona przez nią działalność naukowa dotyczy dziedziny nauk technicznych w dyscyplinie naukowej budowa i eksploatacja maszyn. Główną...
-
Preliminary results from HEDGEHOG REXUS project – A sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaDuring flight, a sounding rocket is subject to a unique environment - severe vibrations and substantial heat flux. In order to design payloads, precise measurement of these conditions is required. This paper presents preliminary results from HEDGEHOG REXUS Project, whose scientific goal was to characterise the thermal and dynamic environment of REXUS sounding rockets. For this purpose, two new sensors have been designed - mechanical...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublikacjaThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
Influence of Different Nanometals Implemented in PMMA Bone Cement on Biological and Mechanical Properties
PublikacjaCemented arthroplasty is a common process to fix prostheses when a patient becomes older and his/her bone quality deteriorates. The applied cements are biocompatible, can transfer loads, and dampen vibrations, but do not provide antibacterial protection. The present work is aimed at the development of cement with antibacterial effectivity achieved with the implementation of nanoparticles of different metals. The powders of Ag,...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublikacjaThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...
-
Investigating lubricants behaviour in microgravity for vibration damping purposes
PublikacjaVibration is one of the harshest environments an object is exposed to during and after launch into space on a launch vehicle. Such vibrations should be damped to avoid destruction of the spacecraft or its elements. Currently, active and material damping is used. A possibility of using lubrication as the damping factor is suggested by some research. MoS2 is a typical solid lubricant used in space applications. Its properties vary...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublikacjaIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Assessment of Subsoil Subsidence Under the Railway Surface with the Use of Fuzzy Sets
PublikacjaThe cause of the subsidence of the railway track is the subsidence of the track bed itself and it is often related to the subsidence of the subsoil. Such settlement leads to: uneven longitudinal railways and track twist. These phenomena have a negative impact on the comfort and safety of driving, and in extreme cases lead to a train derailment. It has been shown that the magnitude of these settlements is determined by many parameters...
-
Study on applicability of two modal identification techniques in irrelevant cases
PublikacjaStudy on applicability of two modal identification techniques in irrelevant cases is made in this paper. The following techniques are considered: Peak Picking based on correlation analysis (PP-CA), dedicated for ambient vibrations and Eigensystem Realization Algorithm (ERA), formulated for free decay vibrations investigation. Irrelevant cases are found when analyzed signals are different than recommended to a given technique. The...
-
Prevention of resonance oscillations in gear mechanisms using non-circular gears
PublikacjaOne of the main disadvantages of gear mechanisms is the occurrence of noise and vibrations. This study investigated the applicability of non-circular gears for preventing resonance oscillations in gear mechanisms. The influence of a small deviation of the gear centrodes from the nominal circles on kinematic and oscillatory characteristics was analysed. It was shown that a larger deviation results in a smaller resonance amplitude...
-
Analog modelling in qualitative analysis of vibration propagation
PublikacjaThe theory of dynamic systems is usually used to model the real systems. The models are based on solving ordinary differential equations, partial or difference, which enable obtaining the relation between input signal and the system response (output signal). The analogy between those models and generalized dynamic systems or control systems can be practically used. Vibration propagation can be described in a similar way as the...
-
Piezo 2011, Electroceramics for End-Users VI
PublikacjaThis work extends a power harvesting with using piezoelectric materials. Experimental presents the development of a piezoelectric MEMS generator which has the ability to scavenge mechanical energy of ambient vibrations from their surroundings and transform it into electrical energy that can be used in energy storage applications. Recent literature shows that piezoelectric transduction has received the most attention for vibration-to-electricity...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublikacjaThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
PublikacjaIn the article the ways of defining tyre rolling resistance are presented. The advantages of the laboratory tests of tyre/road rolling resistance and the advantages and disadvantages of on the road tyre/road rolling resistance tests are described. The description of the special trailer used for tyre/road rolling resistance measurements designed and constructed in the Faculty of Mechanical Engineering at Gdansk University of Technology,...
-
A LUMPED-CIRCUIT MODEL OF CIRCULAR PISTON TRANSDUCER FOR MODELING ITS PERFORMANCE IN DUAL FREQUENCY OPERATING MODES
PublikacjaThe paper presents novel network equivalent circuit of piezoceramic circular disc transducer that takes into account thickness and ra dial mode of vibrations. The starting point of the analysis is 4-port description of circular disc element representing the solution of wave equation set in radial and thickness directions. Th e approximate solution for harmonic case is represented in the form of 4x4 matrix, which is syn thesized...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublikacjaAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
Fabrication and Characterization of Green Polyurethane Foams with Enhanced Vibration Damping Capability
PublikacjaOver the past decades, there has been an intensive development of the technologies and innovations aimed at increasing the quality of life. This development largely concerns the comfort of use of everyday products that, among others, are products of the automotive, construction, or furniture industries. Considering the increase in the comfort of using products such as cars, houses, and flats, one of the comfort features of their...
-
Advanced Mechanics of Marine Structures I, MSc, Summer 2022-2023, [L,T], PG_00051723
Kursy Online1. Literature overview, definition of marine and offshore structures, ocean engineering technologies and mechanical aspects, structural systems applied, jack-up drilling platforms and structural elements. 2. Tensor algebra fundamentals, stress and small strain states of a solid, constitutive relations. 3. SDOF and MDOF dynamic systems, damping and added masses in offshore vibrations, generalised eigenvalue problem, forced vibrations...
-
Rozprzestrzenianie się w podtorzu skutków katastrof kolejowych z udziałem materiałów niebezpiecznych
PublikacjaDuża część przewozów materiałów niebezpiecznych prowadzona jest koleją. W związku z tym bezpieczeństwo tych przewozów nabiera coraz większego znaczenia. Każda katastrofa z udziałem materiałów niebezpiecznych ma negatywny wpływ na uczestników tego zdarzenia oraz na otaczające środowisko, bowiem jej zasięg na ogół nie jest lokalny. Z tego wynika, że w przypadku zaistnienia katastrofy należy minimalizować jej skutki oraz w dalszych...
-
An Improved Method of Minimizing Tool Vibration during Boring Holes in Large-Size Structures
PublikacjaThe paper presents a thoroughly modified method of solving the problem of vibration suppression when boring large-diameter holes in large-size workpieces. A new approach of adjusting the rotational speed of a boring tool is proposed which concerns the selection of the spindle speed in accordance with the results of the simulation of the cutting process. This streamlined method focuses on phenomenological aspects and involves the...
-
Diagnostics of induction motor bearings - possibility of measurements
PublikacjaIn induction motors damage in the elements of electromagnetic system, for example in the wiring of stator, rotor or in the magnetic circuit can appear as well as damage of mechanical parts (bearings, rotor, shaft). Bearing diagnostics is so important in supervision of motor condition, because extensive research shows that the bearings arethe elements most susceptible to damage. This paper presents the research which the author...
-
The influence of the grid density of measurement points on damage detection in an isotropic plate by the use of elastic waves and laser scanning Doppler vibrometry
PublikacjaDamage detection in structural components, especially in mechanical engineering, is an 2 important element of engineering practice. There are many methods of damage detection, in which 3 changes in various parameters caused by the presence of damage are analysed. Recently, methods 4 based on the analysis of changes in dynamic parameters of structures, i.e. frequencies or mode shapes 5 of natural vibrations, as well as changes in...
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublikacjaNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Research on Linear Actuators for Active Foil Bearings
PublikacjaActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublikacjaThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...
-
Viscous versus electromagnetic damping – amplification in a neighbourhood of a mechanism singular position
PublikacjaIn the paper, damping of vibrations are considered and compared in a mechanical and in a electromechanical system. In the system, a continuous beam is considered as the main vibrating element. The compared dissipations methods are based on: viscous dampers and DC generators. To increase the possible damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element....
-
Quality prediction of foil capacitors by acoustic emission signals
PublikacjaJakość i trwałość kondensatorów foliowych jest zależna od ich warunków pracy (np. nadmiarowego napięcia pracy, temperatury, wilgotności) oraz od potencjalnych defektów wprowadzonych na różnych etapach wytwarzania kondensatorów. Nieustanny nacisk na wzrost jakości wytwarzanych elementów przy jednoczesnej redukcji kosztów wytwarzania oznacza, że nowe, tanie i szybkie metody predykcji jakości tych elementów są mocno poszukiwane. W...
-
SPECTRAL RESPONSE OF STATIONARY JACK-UP PLATFORMS LOADED BY SEA WAVES AND WIND USING PERTURBATION METHOD
PublikacjaThe paper addresses non-linear vibrations of offshore jack-up drilling platforms loaded by sea waves and wind in their stationary condition using the perturbation method. Non-linearity of dynamic equations of motion for fixed offshore platforms yields from two factors. The first is load excitation generating non-linear velocity coupling in a dynamic system. This coupling is inherent in the modified Morison equation, involving the...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublikacjaIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Harmonic Vibrations of Nanosized Magnetoelectric Bodies with Coupled Surface and Interphase Effects: Mathematical Models and Finite Element Approaches
PublikacjaThe harmonic problems for piezomagnetoelectric nanosized bodies with taking into account the coupled damping and surface effects are considered on the base of the generalized Gurtin-Murdoch model. In the development of previous investigations, the coupled mechanical, electric and magnetic surface effects with surface inertial terms are introduced into the model. For a homogeneous model, the composite material is considered as homogeneous...
-
On time-dependent nonlinear dynamic response of micro-elastic solids
PublikacjaA new approach to the mechanical response of micro-mechanic problems is presented using the modified couple stress theory. This model captured micro-turns due to micro-particles' rotations which could be essential for microstructural materials and/or at small scales. In a micro media based on the small rotations, sub-particles can also turn except the whole domain rotation. However, this framework is competent for a static medium....
-
Model and laboratory simulation of a induction motor for diagnostic purposes
PublikacjaStatistics say that bearings are this part of induction motors which is most susceptible to damage. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. A faulty bearing results in additional motor vibrations. They are reflected in the harmonic content of stator currents. In certain operating conditions the current signal is the sole source of information...
-
Traffic-induced vibrations. The impact on buildings and people
PublikacjaTraffic-induced vibrations have recently been of major concern to engineers as one of the aspects of so called physical environmental pollution. The interest is related to the observations of serious negative effects of such kind of vibrations on buildings and their inhabitants. Traffic-induced vibrations may cause plaster cracks, structural damage and even failure and collapse of the structure. They may also be the reason of serious...
-
Diagnosis of damages in family buildings using neural networks
PublikacjaThe article concerns a problem of damages in family buildings, which result from traffic-induced vibrations. These vibrations arise from various causes and their size is influenced by many factors. The most important is the type of a road, type and weight of vehicles that run on the road, type and condition of the road surface, the distance from the house to the source of vibrations and many others which should be taken into account....
-
The Idea of Using Bayesian Networks in Forecasting Impact of Traffic-Induced Vibrations Transmitted through the Ground on Residential Buildings
PublikacjaTraffic–induced vibrations may constitute a considerable load to buildings. In this paper, vibrations transmitted through the ground caused by wheeled vehicles are considered. This phenomenon may cause cracking of plaster, cracks in load-bearing elements or even, in extreme cases, collapse of the whole structure. Measurements of vibrations of real structures are costly and laborious. Therefore, the aim of the present paper is to...
-
Application of Support Vector Machine for Determination of Impact of Traffic-Induced Vibrations on Buildings
PublikacjaThe aim of the article is to present an algorithm of Support Vector Machine created to forecast the impact of traffic-induced vibrations on residential buildings. The method is designed to classify the object into one of two classes. The classification into the first class means that there is no impact of vibrations on the building, while classification to the second class indicates the possible influence and suggests the execution...
-
Effect of Pendolino high-speed rail on the structure of buildings located the proximity of the railway tracks
PublikacjaThe following research focuses on the dynamic analysis of the impact of the high-speed train inducted vibrations on the structures located near railway tracks. The office complex chosen as the subject of calculations is located in the northern part of Poland, in Gdańsk, in the proximity of Pendolino, the high speed train route. The high speed trains are the response for the growing needs for more efficient railway system. However...