Filtry
wszystkich: 701
wybranych: 596
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: ŻÓŁTOWSKI
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry - How to apply optical technologies in the diagnosis of reinforced concrete elements?
PublikacjaThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublikacjaWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublikacjaAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublikacjaA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublikacjaThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublikacjaThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Wzrost sprawności turbiny gazowej przez zastosowanie idei Szewalskiego
PublikacjaW artykule przedstawiono wpływ zastosowania upustu na sprawność turbiny gazowej. Upust w turbinie zrealizowano według idei prof. Roberta Szewalskiego, która polega na zastosowaniu upustu międzystopniowego w turbinie gazowej do podgrzewu powietrza zasilającego komorę spalania. Dzięki przeprowadzonej modyfikacji osiąga się wzrost sprawności obiegu oraz spadek zużycia paliwa. Analiza numeryczna obiegu cieplnego przed i po modernizacji...
-
Termodynamiczne uzasadnione modernizacje obiegów cieplnych dla technicznego wykorzystania odnawialnych źródeł energii
PublikacjaW artykule przedstawiono dwa warianty rozwoju istniejących obiektów energetycznych na przykładzie dwóch miast: Ustki i Gorzowa. Oba warianty jak najbardziej są uzasadnione termodynamicznie. W przypadku Ustki wykorzystanie energii geotermalnej do produkcji energii elektrycznej w binarnej siłowni geotermalnej jest jednak nieekonomiczne. Dla Gorzowa zaproponowano modernizację turbiny GT8C w miejsce elektrociepłowni. Wtrysk pary do...
-
Teledetekcyjne badanie konstrukcyjnych elementów żelbetowych z użyciem naziemnego skaningu laserowego
PublikacjaWspółczesna technologia naziemnego skaningu laserowego (TLS) z użyciem skanerów geodezyjnych o zasięgu większym niż 50 metrów pozwala na pomiar geometrii elementów konstrukcyjnych z dokładnością bliską 1 mm. Autorzy, w oparciu o badania laboratoryjne i doświadczenia własne, prezentują rozwiązanie pozwalające na wstępną ocenę belek żelbetowych jako podstawowych elementów konstrukcyjnych budowli typu mosty, wiadukty, budynki wielkopowierzchniowe. Przedmiotem...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublikacjaThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Modelowanie osiągów niskoemisyjnych ogniw paliwowych za pomocą modeli matematycznych typu CFM.
PublikacjaW artykule przedstawiono matematyczny model rurkowego ogniwa paliwowego i jego implementację do własnego kodu typu CFM (Computational Flow Mechanics) o nazwie COM-GAS. Kody numeryczne CFM pozwalają przewidzieć podstawowe parametry ogniwa takie jak: prąd, napięcie, skład spalin etc. Napięcie generowane przez ogniwo paliwowe wyznaczono na podstawie rozszerzonego równania Nernsta. Skład spalin oszacowano opierając się o stałą równowagi...
-
Remote sensing and photogrammetry techniques in diagnostics of concrete structures
PublikacjaRecently laser scanning technologies become widely used in many areas of the modern economy. In the following paper authors show a potential spectrum of use Terrestrial Laser Scanning (TLS) in diagnostics of reinforced concrete elements. Based on modes of failure analysis of reinforcement concrete beam authors describe downsides and advantages of adaptation of terrestrial laser scanning to this purpose, moreover reveal under which...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publikacjan the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublikacjaThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
Activated biochars reduce the exposure of polycyclic aromatic hydrocarbons in industrially contaminated soils
Publikacja -
Optoelectronic properties of the metal-tetracene interface investigated by current noise measurement under monochromatic irradiation.
PublikacjaZaprezentowano badania prądów ograniczonych elektrodowo w warstwach tetracenu. Szczególną uwagę zwrócono na zależność szumów elektrycznych od przyłożonego napięcia i padającego światła.
-
Excitonic stimulation of current flowing along thin tetracene layer
PublikacjaW pracy badane były prądy będące wynikiem oddziaływania ekscytonów tripletowych ze spułapkowanymi nośnikami ładunku w warstwach tetracenu. Badane próbki oświetlane były od strony podłoża oraz od strony przeciwległej podłożu.
-
System SETI-1 jako wspomaganie administrowania Wydziałem ETI PG
PublikacjaArtykuł przedstawia zakres prac i osiągnięcia zespołów zajmujących się informatyzacją administracji Wydziału ETI PG. Tworzony system (robocza nazwana SETI-1) znajduje się aktualnie w początkowej fazie implementacji (zakończono fazy specyfikowania wymagań, analizy i planowania).Autorzy artykułu pracują w tzw. grupach dziedzinowych - odpowiedzialnych za zdefiniowanie i oprogramowanie funkcjonalności systemu przeznaczonych bezpośrednio...
-
Analiza stanu technicznego hali Olivia po 40 latach użytkowania
PublikacjaW artykule przedstawiono stan techniczny konstrukcji hali ''Olivia'' w Gdańsku. Obiekt ten, wybudowany 40 lat temu, znajduje się obecnie w stanie przedawaryjnym. Stalowe, sprężone dźwigary dachowe są unikalnym nie tylko w skali kraju, rozwiązaniem konstrukcyjnym. Przeprowadzono szczegółowy przegląd techniczny całego obiektu, nie wyłączając kanałów kablowych. Z uwagi na nietypowy schemat statyczny dźwigarów dachowych, wykonano 2...
-
Synthesis and structure determination of 2,3-diaryl-9,9-dioxo-1H-9-thia-1,4,4a,7,10-pentaazaphenanthrene-2-ols
Publikacja3-Amino-1,1-dioxopyrido[4,3-e]-1,4,2-dithiazine has been synthesized and applied to the synthesis of 3-amino-2-(4-thioxo-1,4-dihydropyridin-3-ylsulfonyl)guanidine. The reaction of the aminoguanidine with the appropriate 1,2-diarylethane-1,2-diones afforded 2,3-diaryl-9,9-dioxo-1H-9-thia-1,4,4a,7,10-pentaazaphenanthrene-2-ol derivatives. The structure of these compounds, which represent a novel heterocyclic ring system, was confirmed...
-
Analiza zmienności generacji energii elektrycznej w okresie pierwszych pięciu miesięcy 2019 r. ze szczególnym uwzględnieniem generacji energii ze źródeł wiatrowych
PublikacjaW artykule przedstawiono zagadnienia związane z szeroko pojętym rozwojem energetyki wiatrowej. Omówiono stan rozwoju energetyki wiatrowej na świecie. Na podstawie dostępnych badań przybliżono także zagadnienia związane z czynnikami wpływającymi na rozwój odnawialnych źródeł energii oraz ich oddziaływanie na środowisko naturalne. Główny nacisk położono jednakże na analizę zjawisk w pracy Krajowego Systemu Elektroenergetycznego (KSE)...
-
A role of the heat and work uncompensatedtransformations in the balance of entropy and theturbomachinery efficiency
PublikacjaIn the paper we have presented a procedure of estimating a role of the uncompensated transformation of heat and work in ow of viscous and heat conducting uid. The procedure was introduced by Professor Romuald Puzyrewski and is essential in local, in time and space, balance of entropy. Furthermore this unique approach leads to redenition the eciency of uid-ow machinery in three-dimensional modeling using CFD (Computational Fluid...
-
Dynamic deformations tests of Ni3Al based intermetallic alloy by using the split Hopkinson pressure bar technique
Publikacja -
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublikacjaThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Effect of Genetically Modified Feeds on Physico-Chemical Properties of Pork
Publikacja -
Effect of protein-xanthophylls (PX) concentrate of alfalfa supplementation on physico-chemical properties of turkey breast and thigh muscles during ageing
Publikacja -
From fluid mechanics backgrounds to modern field theory
PublikacjaOur presentation keeps a historical line of reasoning, since we start from old concepts of fluid mechanics and finish on concepts of modern field theory. We want to show that some facts from the nature phenomena, which have firstly been discovered on the ground of fluid mechanics, were next incorporated into physics and later become the important pattern for whole mathematical physics. Especially, well-known continuum models, which...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublikacjaThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Multi-layered mineral glass units used as viewport elements of underwater ship structures
PublikacjaIn the paper, Authors deals with viewport elements of underwater marine constructions. If a single-plate viewport constructions are considered, big thicknesses of the glass plate are required to resist the pressure. To build the viewports from the commercially accessible glass panes, multi-layered glass units are proposed in the paper. Numerical calculations are presented, summarized and compared with experimental tests. Focusing...
-
Zagregowana miara oceny stanu dojrzałości organizacji w procesach jej ewolucji.
PublikacjaCelem artykułu jest wskazanie na koniecznośc opracowywania zagregowanych miar pozwalających na ocenę stanu dojrzałości organizacji informatycznych w odniesieniu do procesów ewolucji takich organizacji. Autorzy zwracają uwagę na to, jak w oparciu o wykorzystanie miary złożoności projektu oceniać gotowość organizacji do ewolucyjnych i transformacyjnych zmian. Artykuł został podzielony na cztery główne części. W pierwszej z nich została...
-
Wykorzystanie miar złożoności projektu do oceny stanu ewolucji organizacji informatycznej.
PublikacjaCelem artykułu jest ocena możliwości wykorzystania miar złożoności projektu do oceny stanu ewolucji organizacji informatycznej. Stan ewolucji organizacji informatycznej ma znaczenie dla powszechnego obecnie zjawiska zwinnej transformacji, tak ważnej dla obniżenia ryzyka realizacji projektów informatycznych. Autorzy pracy przedstawili na wstępie problematykę procesów ewolucji organizacji informatycznych w kontekście zmian transformacyjnych....
-
Synchro-photogrammetry in the measurement of objects in motion - the case study
PublikacjaSynchronous photographs and digital photogrammetry methods in a measurement of objects in motion - the experiment. In the following paper, a case study example of a photogrammetric method based on synchronous digital photographs has been presented. This measurement method is an effective solution for tracking of moving objects, dynamic studies and dimensioning of geometry movements. Nowadays, the use of synchronous photography...
-
Building Project and Project Team Characteristics For Creating Hybrid Management Processes
PublikacjaThis paper introduces a method of building the characteristic of Software Development Project. Project characteristic is determined on the basis of several factors such as the complexity of Software Development Project and Project Team, results of historical projects and information on processes and methodologies, which are implemented in analyzed organizations. Information on project complexity can be applied to many different...
-
Trigger-based Model to Assess the Readiness of IT Organizations to Agile Transformation
PublikacjaThe process of change the method of project management from waterfall to agile is called “agile transformation” (AT). The decision to agile transformation is undertaken based on many different factors. Many companies decide to abandon classic, waterfall methodology for agile without prior analysis. This approach makes the processes of agile transformation is hard to control and frequently the implementation of agile fails. The...
-
The Reference Model of Tools Adaptation in the Perspective of Technological Agile Transformaton in IT Organizations
PublikacjaThe scientific aim of the presented paper is the analysis of agile transformation processes in IT organizations in technological perspective of such transformation. The phenomenon of agile transformation becomes a complex challenge for an IT organization, since it has not been analysed in detail so far. There is not any research on the readiness of IT organizations for the realization of agile transformation processes, and such...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublikacjaThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublikacjaThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublikacjaImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Analiza zmienności generacji energii elektrycznej w 2019 r. ze szczególnym uwzględnieniem generacji energii ze źródeł wiatrowych II połowa roku i okres pandemii w 2020 jako czynnik nieprzewidywalny
PublikacjaW artykule przedstawiono zagadnienia związane z szeroko pojętym rozwojem energetyki wiatrowej. Omówiono stan rozwoju energetyki wiatrowej na świecie. Na podstawie dostępnych badań przybliżono także zagadnienia związane z czynnikami wpływającymi na rozwój odnawialnych źródeł energii oraz ich oddziaływania na środowisko naturalne. Główny nacisk położono jednakże na analizę zjawisk w pracy Krajowego Systemu Elektroenergetycznego (KSE)...
-
ANALIZA MAGAZYNOWANIA ENERGII W UKŁADZIE CAES SPRZĘŻONYM Z GRUNTOWYM MAGAZYNEM CIEPŁA
PublikacjaElastyczne i dyspozycyjne elektrownie przyczynią się do trwającego procesu transformacji Polskich Sieci Elektroenergetycznych SA (PSE), ponieważ kompensują wahania energii elektrycznej wytwarzanej z odnawialnych źródeł energii, takich jak wiatr i fotowoltaika. W tym kontekście zasobniki CAES (Compressed Air Energy Storage) są obecnie jedyną alternatywą dla magazynów z wykorzystaniem elektrowni szczytowo-pompowych ze względu na...
-
Modification of structured bio‑carbon derived from spongin-based scaffolds with nickel compounds to produce a functional catalyst for reduction and oxidation reactions: Potential for use in environmental protection
PublikacjaThree different 3D fibrous-like NiO/Ni(OH)2/Ni‑carbonized spongin-based materials were prepared via a simple sorption–reduction method. Depending on the support used, the catalysts were composed of carbon, nickel oxide, nickel hydroxide and zero-valent nickel, with the surface content of the nickel-containing phase in the range 15.2–26.0 wt%. Catalytic studies showed promising activity in the oxidation of phenolic compounds in water...
-
The surface photoconductivity in molecular layers
PublikacjaW pracy przedstawiono rezultaty analizy fotoprądów powierzchniowych w cienkich warstwach tetracenu i pentacenu. W szczególności badano wpływ obecności defektów strukturalnych w warstwach na charakterystyki fotoprądów i transport nośników ładunku.
-
CFD COUPLING OF VOF MODEL WITH ARRHENIUS EQUATION FOR ANALYSIS OF LASER-INDUCED THERMAL DEACTIVATION OF E. COLI
PublikacjaUnderstanding bacterial deactivation at the micro-scale, particularly with E. coli, is crucial for advancing microbiology and has promising applications in biomedical research. In this research contribution, we investigate the thermal inactivation of E. coli bacteria using gold nanoparticles irradiated by a green 1-W laser within a microfluidic chamber. The microfluidic device comprises a fluidic chamber filled with a thin film...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publikacjat Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
Assessment of the Effective Variants Leading to Higher Efficiency for the Geothermal Doublet, Using Numerical Analysis‒Case Study from Poland (Szczecin Trough)
PublikacjaNumerical models of geothermal doublet allows us to reduce the high risk associated with the selection of the most eective location of a production well. Furthermore, modeling is a suitable tool to verify possible changes in operational geothermal parameters, which guarantees liveliness of the system. An appropriate selection of software as well as the methodology used to generate numerical models significantly aects the quality...
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublikacjaPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
On coertia and inertia in aspects of Natanson’s nonlinear extended thermodynamics
PublikacjaIn this article, the previously underrepresented contributions of Natanson to the field of thermodynamics have been presented. In order to identify a source of irreversibility at Nature, Natanson introduced the concept of Coertia, which is similar to inertia. Natanson’s Coertia is a fundamental property of space that is responsible for every irreversible phenomena in matter, as well as in the electromagnetic and gravitational fields....
-
Peptidoglycan hydrolases - potential weapons against Staphylococcus aureus
PublikacjaBacteria of the genus Staphylococcus are common pathogens responsible for a broad spectrum of human and animal infections and belong to most important etiological factors causing food poisoning. Because of rapid increase in prevalence of isolation of staphylococci resistant to many antibiotics, there is an urgent need for development of new alternative chemotherapeutics. A number of studies have recently demonstrated the strong...