Filtry
wszystkich: 1962
wybranych: 1377
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: motor transportation
-
Asymmetrical Modes in Polyphase Motors and Drives
PublikacjaThe effect of power supply and/or motor asymmetry on the phase-load distribution and the ripple of electromagnetic torque in a polyphase drive is studied by the method of symmetrical components. It is shown that the presence of asymmetry causes the mapping of all harmonics in the supply voltage into all planes of symmetrical components and eliminates the possibility of independent control of harmonics. The dynamic model of a five-phase...
-
Selected Issues of Hybrid Outboard Motors
PublikacjaThe aim of the research reported in the article was designing a hybrid drive system based on an outboard internal combustion engine offered by a selected producer and testing its operating characteristics. The article presents different designs of this type of drive which can be found in the literature and are available in the market. The designed hybrid outboard drive system was tested both on the laboratory test rig and in real...
-
The application of Gabor transformation in the harmonic analysis of corrosion processes
Publikacja -
Fast impedance measurement method using Laplace transformation
PublikacjaArtykuł przedstawia metodę pomiaru impedancji wykorzystującą rzeczywisty uskok jednostkowy step jako sygnał pobudzenia i transformację Laplace jako narzędzie analizy sygnału odpowiedzi testowanego obiektu. Metoda jest dedykowana do badania różnych obiektów technicznych (np. powłok antykorozyjnych, czujników gazu, ceramik, tkanek biologicznych itp.) gdy czas pomiaru nie może być długi. Przedstawiona metoda jest znana ale niezbyt...
-
Kerogen to bitumen transformation with respect to host rock environment
PublikacjaResearch focuses on analyzing the role of rock constituents in kerogen transformation. It includes mineral and organic matter characterization, kerogen and bitumen isolation, quantification, and determination of the critical factors of transformation ratio concerning generating mobile versus less mobile hydrocarbons. The results indicate that the ratio mainly depends on the distribution and type of kerogen in the basin, and secondly...
-
Redesigning Informal Beirut: Shaping the Sustainable Transformation Strategies
PublikacjaLebanon is distinguished by its strategic geographical location among the Arab countries. Beirut, as the capital city and the major commercial and cultural centre of the country, is a point of interest for migrants. The region has witnessed many changes since the end of World War II, which have resulted in internal and external conflicts, migrations, the centralization of the country’s economy, etc. Furthermore, the city has witnessed...
-
Digital transformation and economic growth - DESI improvement and implementation
PublikacjaThe paper aims to improve the methodology of the Digital Economic and Society Index (DESI), the European Commission’s newest index to assess the development of the digital economy. In particular, we investigate whether methodological changes to the structure of DESI improve its ability to capture the digital transformation of EU economies. Using the sensitivity- based analysis, we check whether the selection of weights of individual...
-
Towards better understanding of context-aware knowledge transformation
PublikacjaConsidering different aspects of knowledge functioning, context is poorly understood in spite of intuitively identifying this concept with environmental recognition. For dynamic knowledge, context especially seems to be an essential factor of change. Investigation on the impact of context on knowledge dynamics or more generally on the relationship between knowledge and its contextual interpretation is important in order to understand...
-
The role of organic and mineral constituents on kerogen transformation ratio
PublikacjaThe main aim of this dissertation is to determine the role of mineral and organic matter constituents in kerogen transformation ratio. Practical aspects of the work include application of the results in the assessment of hydrocarbon production potential; to make process of hydrocarbon recovery more predictable consistent and efficient. The work used shale from the Vaca Muerta formation from the Nequen basin in Argentina. The formation...
-
The transformation of the Chinese stock market between 1990 and 2012
PublikacjaThe main purpose of this paper is to examine the transformation of the stock market in the People’s Republic of China (i.e. concentrated on stock exchanges in Shanghai and Shenzhen; the stock exchange in Hong Kong was omitted) from its beginnings in the early 1990s, through rapid development over the next two decades, up to the financial crisis of 2008 (the period examined is 1990–2012). The paper presents a short history of the...
-
Application of the wavelet transformation to estimation of intensity of pitting corrosion
PublikacjaAnalizie poddane zostały dane szumowe odpowiadające korozji wżerowej. Stwierdzona została korelacja pomiędzy intensywnością rejestrowanego szumu a ubytkiem masy elektrod stalowych. Na bazie przekształcenia falkowego zaproponowany został parametr charakteryzujący zaatakowanie wżerowe. Stwierdzono, że z grupy wytypowanych wskaźników prezentowany parametr wskazuje najlepszą korelację z wielkościami ubytków mas elektrod.
-
On the use of bilinear transformation for parameter identification of anticorrosion coatings
PublikacjaW artykule przedstawiono metodę identyfikacji parametrów powłok antykorozyjnych modelowanych wieloelementowymi układami zastępczymi. Metoda wykorzystuje właściwości przekształcenia biliniowego, które umożliwia przedstawienie funkcji układowej wieloparametrowego modelu jako funkcji każdego indywidualnego parametru. Odwrotne przekształcenie biliniowe pozwala na wyznaczenie wartości każdego z parametrów modelu z osobna na podstawie...
-
The application of Gabor transformation in the harmonic analysis of corrosion processes.
PublikacjaZaproponowana została nowa metoda analizy widmowej niestacjonarnych procesów korozyjnych. Analizie poddany został układ modelujący pierwszorzędową reakcję elektrodową. Wykazano, że w przypadku pobudzenia układu liniowo zmieniającym się potencjałem z nałożoną składową sinusoidalną przekształcenie Fouriera nie odzwierciedla zmian amplitudy powstających składowych harmonicznych. Jako rozwiązanie zaproponowana została analiza...
-
Analysis of spontaneous electrochemical oscillations by the wavelet transformation method.
PublikacjaW pracy została przedstawiona nowa metoda analizy oscylacji prądu, które związane są z anodowym roztwarzaniem metali. Transformacja falkowa jest używana do rozdzielenia i analizy spektralnej pojedynczych przebiegów elementarnych komponentów oscylacji elektronicznych. Zastosowana została metoda rozkładu energii oscylacji analogiczna do funkcji spektralnej gęstości mocy.Wykazano, że chaotyczne składniki (chaos Shilnikova)...
-
The transformation of Polish foreign trade in European integration process
PublikacjaW artykule analizowane są przemiany handlu zagranicznego Polski w warunkach integracji ze Wspólnotami Europejskimi. Okres analizy obejmuje lata 1980-2003 i 2004 - lipiec 2005.
-
Revolutionizing SME Management: The Digital Transformation of Financial Operations
Publikacja -
The Changing Nature of In‐Between Spaces in the Transformation Process of Cities
PublikacjaIn the in‐between spaces of cities, there are many problems of various nature and scale: functional, spatial, economic, environmental, visual, and social. There are also some hidden potentials that can be activated. The aim of the article is to explore the possibilities of solving existing problems and to show the possibilities of using the potentials of in‐between spaces with regard to the changing nature of a city. The article,...
-
Nitrogen transformation during fermentation in agricultural biogas plants
PublikacjaThe aim of the present study was to determine changes in the organic nitrogen fraction in the liquid fraction of the digestate during laboratory tests of mono- and co-digestion. Three agricultural wastes were tested: distillery residue, cattle slurry and corn silage. In the mono-fermentation tests, the initial total nitrogen concentration depended on the feedstock used. As a result of the hydrolysis and ammonification of the organic...
-
Induction Motor Multiscalar Model Based Sensorless Control Using Power Measurement
Publikacja -
Research on a control system based on stepping motor for ship's controllable pitch propellers
PublikacjaW artykule przedstawiono opis stanowiska laboratoryjnego do badania serwomechanizmów okrętowych śrub nastawnych małej mocy oraz opracowany układ sterowania zdalnego śruby z wykorzystaniem elektrycznego silnika krokowego. Przedstawiono także wyniki pierwszej serii badań układu sterowania śruby nieobciążonej dla skokowego zadawanych wartości skoku śruby przy dwóch różnych prędkościach obrotowych silnika krokowego.
-
Stability of a proportional observer with additional integrators on the example of the flux observer of induction motor
PublikacjaArtykuł opisuje zagadnienia związane ze stabilnością proporcjonalnego obserwatora Luenbergera z dodatkowymi integratorami
-
3D Hand Shape Modeling for Automatic Assessing Motor Performance in Parkinson's Disease
PublikacjaIn this paper a method for hand pattern processing to create a 3D hand model is presented. By applying a complete hand armature to the model obtained, an interpolation of three motor tests for an individual Parkinson's disease patient can be performed. To obtain the 3D hand model the top view of the hand from a web cam is analyzed. The hand contour is examined to find characteristic points that allows for dividing hand image into...
-
Properties of water in the region between a tubulin dimer and a single motor head of kinesin
PublikacjaA kinesin is a molecular motor that can perform movement on a microtubule track in a stepping-like manner. This motion is connected with processes of association and dissociation of kinesin and tubulin. Water is an important participant in these kinds of molecular interactions. This is why we have decided to investigate the dynamical and structural properties of water in the region between the kinesin catalytic domain and the tubulin...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Increasing Electric Vehicles Reliability by Non-Invasive Diagnosis of Motor Winding Faults
Publikacja -
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublikacjaIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
Selected dynamic properties of adaptive proportional observer of induction motor state variables
PublikacjaThis paper presents problems related to the design and the stability of adaptive proportional observer which is used for estimation of magnetic flux and motor speed in sensorless control systems of induction motor. The gain matrix of the observer was chosen by genetic algorithm and alternatively by pole placement method. It has been shown that adaptive proportional observer is stable if the...
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublikacjaThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
Five-phase Induction Motor Drive Operation During Stator Phase Fault
PublikacjaThe article presents the most important advantages of multi-phase electric drives. The construction of a five-phase squirrel cage induction motor together with possible stator winding distribution cases is presented, which affect the properties of such motor. Increased reliability of five-phase drives was indicated. The drive operation properties were confirmed by experimental results.
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublikacjaThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublikacjaInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublikacjaThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
The computer numerical control system with permanent magnet synchronous motor servo-drives.
PublikacjaPrzedstawiono układ serwonapędów wieloosiowej maszyny sterowanej numerycznie. W układzie wykorzystano silniki synchroniczne z magnesami trwałymi oraz procesory synałowe DSP. Omówiono algorytmy sterowania nadrzędnego oraz problemy sterownia silnika PMSM.
-
Determination of equivalent circuit parameters of an induction motor using field calculation software
PublikacjaSimulation of the drive system comprising a power electronic converter and an induction motor requires that the equivalent circuit parameters of the motor are known. These parameters can be either measured or calculated. A method of calculation of self and mutual inductances that are parameters of a polyphase model of the motor is presented in the paper. All self-inductances and mutual inductances have been calculated using the...
-
Model and simulation tests of a squirrel-cage induction motor with oscillation of air gap
PublikacjaPrzedstawiono model matematyczny silnika, który pozwala na wprowadzanie ekscentryczności wirnika. Zaprezentowano obliczone widma prądu z wprowadzoną oscylacją wirnika, co z pewnym przybliżeniem odpowiada uszkodzeniu łożyska. Rezultaty symulacji pozwalają na określenie zależności pomiędzy oscylacją szczeliny powietrznej i składowych w widmie prądu.
-
Nonlinear control of induction motor in field weakning region with consideration of stator flux
PublikacjaMetody nieliniowgo sterowania mogą poprawić właściwości silnika indukcyjnego w stanach przejściowych wektora strumienia. Badano sterowanie oparte na modelu multiskalarnym silnika indukcyjnego w zakresie osłabiania pola. Dwie nowe zmienne wejściowe pojawiające się w modelu multiskalarnym są równe czynnej i biernej mocy silnika. Pokazano, że te wielkości mogą byc kompensowane, jeżeli rozważane są jako mierzone zakłócenia. Maksymalny...
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublikacjaDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Multiscalar Control Based Airgap Flux Optimization of Induction Motor for Loss Minimization
PublikacjaBased on the induction motor model, considering the core loss resistance that accounts for magnetic characteristic saturation, a speed control approach is devised with an adaptive full-order (AFO) speed observer. The induction motor model analysis is done sincerely in a stationary reference frame. The control approach incorporates a flux reference generator designed to meet optimal operational circumstances and a nonlinear speed...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublikacjaThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublikacjaThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublikacjaIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
Application of neural networks for identification of forcedness having effect on magnitude of turbine rotor vibration using rotor trajectory.
PublikacjaW pracy dokonano analizy zastosowania sieci neuronowych do wyznaczenia wartości wymuszeń wpływających na wielkość drgań wirnika używając trajektorii jako parametr określający drgania. Badania przeprowadzono na powietrznej, jednostopniowej turbinie modelowej. Przemieszczenia poziome i pionowe wirnika turbiny mierzono przy pomocy systemu pomiarowego i rejestrowano na oscyloskopie cyfrowym. Przeprowadzono pomiary trajektorii ruchu...
-
Pipeline system for heat transportation from nuclear power plant — An optimizing approach
Publikacja -
Fatigue tests of steel Sandwich panel. Fifth International Conference on Marine Technology and Transportation.
PublikacjaW referacie przedstawiono wyniki badań laboratoryjnych paneli SANDWICH prowadzonych w Katedrze Technologii Okrętów, Systemów Jakości i Materiałoznawstwa Wydziału OiO na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów w wynikami prezentowanymi w literaturze.
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublikacjaThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Computational investigations of acoustic radiation from end shields of small-power electric motor
PublikacjaW artykule omówiono rozwój metod modelowania własności akustycznych maszyn elektrycznych. Wskazano na pomijalny dotąd, znaczący udział drgań tarcz łożyskowych w emitowaniu hałasu przez silniki małej mocy. Na podstawie równania falowego potencjału prędkości wyprowadzono analityczne formuły do obliczeń akustycznych w polu bliskim tarczy łożyskowej. Zamieszczono uzyskane z serii obliczeń dla pracującego silnika, rozkłady ciśnienia...
-
Comparison of two methods for parameters selection of the proportional observer of induction motor state variables
PublikacjaArtykuł opisuje problemy odtwarzania prędkości obrotowej wału maszyny indukcyjnej przy wykorzystaniu estymatorów MRAS. Porównano dwie metody doboru wzmocnień obserwatora, analityczną i bazującą na algorytmach genetycznych
-
Control Systems of an Induction and Synchronous Motor Supplied by Current Source Converter Working as Generator
Publikacja -
Novel adaptive flux observer for wide speed range sensorless control of induction motor
PublikacjaA new adaptive flux observer of induction motor is presented in the paper. The Lyapunov theory is utilized for derivation of the adaptation law of rotor flux angular speed, which acts as unknown parameter in an augmented induction motor model. In the field weakening region, where stray fluxes are comparable with rotor flux magnitude, the air-gap flux stabilization is proposed. An air-gap flux multiscalar model is derived for stator...
-
The Adaptive Backstepping Control of Permanent Magnet Synchronous Motor Supplied by Current Source Inverter
Publikacja...