Filtry
wszystkich: 538
wybranych: 470
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: Copts
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublikacjaThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
Warstwowy system zabezpieczeń w przemysłowych instalacjach podwyższonego ryzyka
PublikacjaRozdział poświęcono aktualnym zagadnieniom analizy i projektowania warstw zabezpieczeń w kontekście oceny ryzyka i zarządzania bezpieczeństwem funkcjonalnym w cyklu życia z wyróżnieniem trzech warstw: (1) podstawowego systemu sterowania BPCS (basic process control system), (2) człowieka-operatora korzystającego opcjonalnie z systemu alarmowego AS (alarm system) oraz (3) przyrządowego systemu bezpieczeństwa SIS (safety instrumented...
-
Mathemathical model of radial passive magnetic bearing
PublikacjaIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublikacjaBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Adapting new tools of urban freight management based on Gdynia’s dedicated delivery bays example – an analysis of the process
PublikacjaThe article presents an analysis of a process which ultimately helped Gdynia to designate pilot delivery sites in its downtown area using international experience. A verification was conducted of policy transfer theory and its practical implementation based on an URBACT Freight Tails project. While the choice of the solution was based on critical analysis of existing practical examples, it needed to be adapted to the local conditions...
-
RSS-Based DoA Estimation Using ESPAR Antenna Radiation Patterns Spline Interpolation
PublikacjaIn this paper, it is shown how power pattern crosscorrelation (PPCC) algorithm, which relies on received signal strength (RSS) values recorded at electronically steerable parasitic array radiator (ESPAR) antenna output port, used for direction-of-arrival (DoA) estimation, can easily be improved by applying spline interpolation to radiation patterns recorded in the calibration phase of the DoA estimation process. The proposed method...
-
A novel calibration method for RSS-based DoA estimation using ESPAR antennas
PublikacjaIn this paper, we introduce a new calibration method that can successfully be used in direction of arrival (DoA) estimation using electronically steerable parasitic array radiator (ESPAR) antennas and employing power-pattern cross-correlation (PPCC) algorithm, which relies on received signal strength (RSS) values recorded at the antenna output port. Instead of the commonly used two-step approach, during which ESPAR antenna calibration...
-
RSS-based DoA Estimation Using ESPAR Antennas and Interpolated Radiation Patterns
PublikacjaIn this letter, it is shown how an algorithm, which employs received signal strength (RSS) values in order to estimate direction-of-arrival (DoA) of impinging signals in wireless sensor network (WSN) nodes equipped with electronically steerable parasitic array radiator (ESPAR) antennas, can easily be improved by applying an interpolation algorithm to radiation patterns recorded in the calibration phase of the DoA estimation process....
-
Adaptive stochastic and hybrid nonlinear optimization algorithms for improving the effectiveness of the biological processes at WWTP
PublikacjaWastewater treatment plays an important factor in the modern world. Insufficient treatment may result in environmental pollution which can further lead to disasters and diseases. However, processes that take place inside wastewater treatment plants (WWTP) are highly complex in nature, therefore it is difficult to design an efficient, optimal control system. The problem regarding biochemical reactions inside Sequential Batch Reactor...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Failures and a concept of corrosion protection system for spiral classifiers at KGHM Polska Miedź S.A. Ore Concentration Plant
PublikacjaThe Ore Concentration Plant, where the process of flotation is carried out as well as the final production of copper concentrate, plays a key role in the entire production line of KGHM Polska Miedź S.A. Majority of operations related to the run-of-mine preparation to copper flotation enrichment are carried out in a water environment. The maintaining of production process continuity requires to pursue minimisation of many production...
-
Początek Gdyńskiego Systemu Wodociągowego Planowanie i budowa lokalnego układu wodociągowego na Kępie Oksywskiej (1929 – 1932. Część II.
PublikacjaUdokumentowanie procesu inwestycyjnego przekształcenia wodociągu wiejskiego w miejski układ wodociągowy na podstawie analizy materiałów źródłowych. Ustalenie hydrogeologicznych uwarunkowań decyzji o lokalizacji ujęcia wody „Oksywie”. Identyfikacja parametrów konstrukcyjnych i kosztów budowy trzech budynków na ujęciu wody: mieszkalnego, stacji pomp i odżelaziania wody. Odtworzenie przebiegu budowy struktury sieci wodociągowej w...
-
Bypass kolejowy dla wiaduktu łukowego i kratownicowego w ciągu modernizowanej linii kolejowej E59 na odcinku Wronki – Dobiegniew
PublikacjaW artykule przedstawiono realizacje bypassu kolejowego, zlokalizowanego nieopodal miejscowości Krzyż Wielkopolski w ciągu linii kolejowej E59 na skrzyżowaniu z linią kolejową 203. Wariantowa analiza kilku zaproponowanych rozwiązań wykazała, ze wykonstruowanie bypassu na czas prowadzenia prac modernizacyjnych pozwoli na utrzymanie ciągłości ruchu kolejowego, nie stworzy nadmiernych problemów podróżnym, a jednocześnie pozwoli na...
-
Model obliczania kosztu cyklu życia obiektu na przykładzie budynku mieszkalnego jednorodzinnego
PublikacjaW artykule przedstawiono model obliczania kosztu cyklu życia budynku mieszkalnego jednorodzinnego oraz wskazano możliwości ograniczenia wydatków związanych z jego użytkowaniem w okresie trzydziestu lat. Celem prezentowanej analizy rachunku kosztu cyklu życia jest porównanie i ocena kosztów nabycia i użytkowania domu realizowanego według alternatywnych technologii z uwzględnieniem przyjętych rozwiązań w zakresie pozyskania energii,...
-
Denitrification Process Enhancement and Diversity of the Denitrifying Community in the Full Scale Activated Sludge System after Adaptation to Fusel Oil
PublikacjaImplementation of anaerobic digestion of primary sludge in modern wastewater treatment plants (WWTPs) limits the availability of organic carbon for denitrification in conventional nitrification-denitrification (N/DN) systems. In order to ensure efficient denitrification, dosage of the external carbon source is commonly undertaken. However, application of commercial products, such us ethanol or acetate, greatly increases operational...
-
BEARING SYSTEMS OF WIND TURBINES – MAINTENANCE PROBLEMS
PublikacjaW praktyce eksploatacyjnej turbin wiatrowych o tradycyjnej konstrukcji (przekładniowych) obserwowana jest duża awaryjność przekładni, a zwłaszcza łożysk tocznych szybkoobrotowych wałów przekładni. W Polsce na zlecenie właściciela dużej farmy wiatrowej, firmy Energa Wytwarzanie S.A., Politechnika Gdańska we współpracy z Politechniką Poznańską i Akademią Górniczo Hutniczą podjęły badania mające na celu diagnozowanie przyczyn uszkodzeń...
-
Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound
PublikacjaUltrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...
-
Recovery and re-use of photovoltaic solar cells from crystalline silicon
PublikacjaCrystalline silicon-type PV modules consist, in order of mass, of glass, an aluminium frame, an EVA coating, solar cells, a terminal box, back film and tapping screws. From the economic point of view, pure silicon, recoverable from spent cells, is the most important material owing to its cost and shortage. For crystalline, silicon-based PV cells, the following chemical treatments were performed: removal of the metal coating, followed...
-
Evolving gene regulatory networks controlling foraging strategies of prey and predators in an artificial ecosystem
PublikacjaCo-evolution of predators and prey is an example of an evolutionary arms race, leading in nature to selective pressures in positive feedback. We introduce here an artificial life ecosystem in which such positive feedback can emerge. This ecosystem consists of a 2-dimensional liquid environment and animats controlled by evolving artificial gene regulatory networks encoded in linear genomes. The genes in the genome encode chemical...
-
Determination of total mercury in raw petrol using cold vapour atomic absorption spectrometry
PublikacjaPresence of different forms of mercury in petroleum based products may impair the proper operation of the equipment or led to poisoning of automotive catalysts. However much more important problem is environmental pollution with mercury emitted from different types of fossil fuels. Although the average mercury concentration in petroleum based products (automotive fuels) is on the level around 1 ppb, taking into account annual...
-
Comparison of selected algorithms for scheduling workflow applications with dynamically changing service availability
PublikacjaThis paper compares the quality and execution times of several algorithms for scheduling service based workflow applications with changeable service availability and parameters. A workflow is defined as an acyclic directed graph with nodes corresponding to tasks and edges to dependencies between tasks. For each task, one out of several available services needs to be chosen and scheduled to minimize the workflow execution time and...
-
Programmatic Simulation of Laser Scanning Products
PublikacjaThe technology of laser scanning is widely used for producing three-dimensional digital representations of geographic features. The measurement results are usually available in the form of 3D point clouds, which are often used as a transitional data model in various remote sensing applications. Unfortunately, while the costs of Light Detection And Ranging scanners have dropped significantly in recent years, they are still considered...
-
Hydrodron — New Step for Professional Hydrography for Restricted Waters
PublikacjaHydrographic surveys in restricted areas are becoming increasingly important, but often impossible to carry out with conventional hydrographic vessels. Presumably in this case an employment of unmanned vehicles is the only reasonable solution. As restricted water areas include, among others: harbours, roadsteads, rivers or lakes. The HydroDron platform, due to its mobility, can operate in the above-mentioned areas. It is adapted...
-
Thermal decomposition kinetics of dynamically vulcanized polyamide 6-acrylonitrile butadiene rubber-halloysite nanotube nanocomposites
PublikacjaThermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m‐CR) isoconversional models were used to obtain information about the kinetics of the thermal...
-
Towards solving heterogeneous fleet vehicle routing problem with time windows and additional constraints: real use case study
PublikacjaIn advanced logistic systems, there is a need for a comprehensive optimization of the transport of goods, which would reduce costs. During past decades, several theoretical and practical approaches to solve vehicle routing problems (VRP) were proposed. The problem of optimal fleet management is often transformed to discrete optimization problem that relies on determining the most economical transport routes for a number of vehicles...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublikacjaNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Modeling sequencing batch reactor operational conditions depending on oxygen concentration
PublikacjaSequencing batch reactors (SBR) can be used as a fill-and draw activated sludge system for wastewater treatment with considerable operating flexibility and the possibility to conduct experiments under standard conditions and extreme case scenarios. Mathematical modeling and computer simulations provide an opportunity to implement existing wastewater processes in modeling software and evaluate different modifications at low costs...
-
Expedited Feature-Based Quasi-Global Optimization of Multi-Band Antenna Input Characteristics with Jacobian Variability Tracking
PublikacjaDesign of modern antennas relies—for reliability reasons—on full-wave electromagnetic simulation tools. In addition, increasingly stringent specifications pertaining to electrical and field performance, growing complexity of antenna topologies, along with the necessity for handling multiple objectives, make numerical optimization of antenna geometry parameters a highly recommended design procedure. Conventional algorithms, particularly...
-
APPLICATION OF APRIORI ALGORITHM IN THE LAMINATION PROCESS IN YACHT PRODUCTION
PublikacjaThe article specifies the dependence of defects occurring in the lamination process in the production of yachts. Despite great knowledge about their genesis, they cannot be completely eliminated. Authentic data obtained through cooperation with one of the Polish yacht shipyards during the years 2013–2017 were used for the analysis. To perform a simulation, the sample size was observed in 1450 samples, consisting of 6 models of...
-
Mobile Cloud computing architecture for massively parallelizablegeometric computation
PublikacjaCloud Computing is one of the most disruptive technologies of this century. This technology has been widely adopted in many areas of the society. In the field of manufacturing industry, it can be used to provide advantages in the execution of the complex geometric computation algorithms involved on CAD/CAM processes. The idea proposed in this research consists in outsourcing part of the load to be com- puted in the client machines...
-
Practical I-Voting on Stellar Blockchain
PublikacjaIn this paper, we propose a privacy-preserving i-voting system based on the public Stellar Blockchain network. We argue that the proposed system satisfies all requirements stated for a robust i-voting system including transparency, verifiability, and voter anonymity. The practical architecture of the system abstracts a voter from blockchain technology used underneath. To keep user privacy, we propose a privacy-first protocol that...
-
Development of Strategies for AOB and NOB Competition Supported by Mathematical Modeling in Terms of Successful Deammonification Implementation for Energy-Efficient WWTPs
PublikacjaNovel technologies such as partial nitritation (PN) and partial denitritation (PDN) could be combined with the anammox-based process in order to alleviate energy input. The former combination, also noted as deammonification, has been intensively studied in a frame of lab and full-scale wastewater treatment in order to optimize operational costs and process efficiency. For the deammonification process, key functional microbes include...
-
Integrated Photocatalytic Advanced Oxidation System (TiO2/UV/O3/H2O2) for Degradation of Volatile Organic Compounds
PublikacjaSeveral advanced oxidation processes (AOPs) including photocatalytic processes were studied for effective treatment of complex model wastewater containing a wide variety of VOCs. The studies revealed synergistic effects of TiO2 based processes for improved degradation of the VOCs. A peroxone combined with TiO2/UV system (TiO2/UV/O3/H2O2) with a ratio between the oxygen source from the oxidant to chemical oxygen demand (COD) of...
-
The role of stakeholders on rejection of bankruptcy applications in the case of “poverty” of the estate: A Polish case study
PublikacjaThe aim of this article is to supplement the Law and Economics area of science with regard to the scope of the ex ante effectiveness of bankruptcy law using the example of Poland. Bankruptcy law is effective in the ex ante stage when it eliminates from the market insolvent entrepreneurs who cannot even afford to cover the costs of bankruptcy proceedings. In these cases, the bankruptcy court should dismiss the petition for bankruptcy...
-
In search of the new: American volunteers’ opinions about their participation in the Teaching English in Poland (TEIP) Program
PublikacjaThe Teaching English in Poland (TEIP) program relies on summer camps during which native English speakers, American volunteers, teach Polish children and adolescents using the language immersion method – during everyday activities, sports and art classes, and similar occasions. A vital aspect of the evaluation of the program is researching its impact on the young people; however, the opinions of the volunteers regarding their...
-
Algorytmy hybrydowe optymalizacji w zastosowaniu do problemu sterowania systemami dystrybucji wody
PublikacjaW pracy analizowany jest problem optymalizującego zintegrowanego sterowania ilością i jakością w systemach dystrybucji wody. Proponowane decyzje i sterowania powinny zapewniać optymalizację przyjętego wskaźnika jakości, przy spełnieniu ograniczeń właściwych tej klasie systemów. Ostatecznie do rozwiązania złożonych zadań optymalizacji dynamicznej zaproponowane zostało podejście hybrydowe, wspomagające predykcyjne algorytmy sterowania...
-
Protection of historical heritage as part of the development of cultural tourism – a case study of the community of Kamieniec Ząbkowicki in Lower Silesia
PublikacjaBoth literature and economics show a changing approach to historical heritage. It is no longer seen as a resource that generates only high maintenance costs. Analyses of local government units (LGUs) show that historical heritage is a strength rather than a weakness. More and more often, it is considered in economic development strategies as an asset that creates new activities and functions, generates income, and creates jobs....
-
Investigating Fuel Injection Strategies to Enhance Ship Energy Efficiency in Wave Conditions
PublikacjaThe prediction of fuel consumption and resulting transportation costs is a crucial stage in ship design, particularly for conditions involving motion in waves. This study investigates the real-time fuel consumption of a container ship when sailing in waves. The overall ship performance is evaluated using a novel non-linear coupled hull-engine-propeller interaction model. A series of towing tank experiments for hull resistance in...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublikacjaIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
Methods for physical impairment constrained routing with selected protection in all-optical networks
PublikacjaIn this paper, we investigate the problem of survivable all-optical routing in WDM networks with physical impairments. One of the recent key issues in survivable optical network design refers to maximization of the ratio of routeable demands while keeping the overall network cost low. In WDM networks, this goal can be achieved by routing as many demands in all-optical way as possible. Based on the latest technical trends driven...
-
Real-time simulator of agricultural biogas plant
PublikacjaThis article presents a real-time simulator of an agricultural biogas plant. The project contains biogas and biomass circuits simulation, as well as heating circuit simulation with a complete control system and visualization interface of the whole process. The software tool used to simulate the plant work is CFD (Computational Fluid Dynamics), which enables a user to create and test simulation objects based on fundamental physical...
-
Variable Fractional Delay Filter Design Using a Symmetric Window
PublikacjaIn this paper a numerically efficient method for designing a nearly optimal variable fractional delay (VFD) filter based on a simple and well-known window method is presented. In the proposed method a single window extracted from the optimal filter with fixed fractional delay (FD) is divided into even and odd part. Subsequently, the odd part is discarded and symmetric even part of the extracted window is used to design a family...
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublikacjaOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Energy Losses Due to Imperfect Payment Infrastructure and Payment Instruments
PublikacjaOne of the strategic objectives of the European Union is a reduction in greenhouse gas emissions and improvement of energy efficiency by at least 32.5% in different areas of the economy by 2030. However, little is known about the impact of payment in retail on energy consumption. The purpose of this paper is to assess the chain of losses of time and energy, and therefore financial losses, that occur due to the imperfection of payment...
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublikacjaThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Analysis of Investments in RES Based on the Example of Photovoltaic Panels in Conditions of Uncertainty and Risk—A Case Study
PublikacjaThe aim of this study is to examine the profitability of investment in a photovoltaic microinstallation, to analyze the impact of legal changes on its profitability, and to perform a sensitivity analysis of the investment profitability to energy price changes. The novelty of the research applies to the financial analysis of two legal systems of discount called net-metering and net-billing. The two systems and the change in energy...
-
Evolutionary benefits of personality traits when facing workplace bullying
PublikacjaFacing workplace bullying negatively affects physical and mental health, and consequently quality of life and well-being. Personality traits that can help an individual survive and reproduce entail more benefits than costs. Building on two evolutionary theories, Life History Theory and Costly Signaling Theory, this study aims to provide novel insights into how and why personality traits are associated with facing workplace bullying...
-
ALGORYTMY STEROWANIA SILNIKA WYSOKOPRĘŻNEGO Z UKŁADEM COMMON RAIL
PublikacjaRozwój wiedzy i technologii związanej z procesami spalania paliwa w silniku i prowadzeniem kontrolowanego procesu spalania, skutkuje wzrostem sprawności silników i lepszą ochroną środowiska. Ciekawym rozwiązaniem technicznym jest silnik z zapłonem samoczynnym pracujący z bardzo wysokim ciśnieniem wtrysku paliwa i często z recyrkulacją spalin – silnik z układem Common Rail. Do sterowania silnika stosowane są złożone układy mechatroniczne...
-
Głowice optoelektroniczne bezzałogowych środków latających
PublikacjaBezzałogowe środki latające nie wymagają długiego i kosztownego szkolenia załóg. Koszty ich wdrożenia są wielokrotnie niższe od załogowych środków latających. Bezzałogowe środki latające są następcami załogowych pojazdów latających rozpoznawczych i obserwacyjnych. Jednym z podstawowych elementów wyposażania bezzałogowego środka latającego jest głowica optoelektroniczna. Głowice wyposażone są w systemy rejestracji i śledzenia wskazanych...
-
Deregulacja polskiego rynku pracy
PublikacjaHistorycznie ukształtowana regulacja rynku pracy związana jest z jego infrastrukturą organizacyjno-prawną, tzn. przepisami dotyczącymi płac, czasu pracy i ochrony stosunku pracy. W opinii zwolenników deregulacji utrudnia ona elastyczne dostosowywanie się do rozmiarów zatrudnienia w zależności od zaistniałej sytuacji gospodarczej, powodując wzrost bezrobocia strukturalnego i wzrost kosztów pracy. Deregulacja rynku pracy związana...