Filtry
wszystkich: 905
-
Katalog
Wyniki wyszukiwania dla: INFILL ANGLE
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublikacjaIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
Facile formation of self-organized TiO2 nanotubes in electrolyte containing ionic liquid - ethylammonium nitrate and their remarkable photocatalytic properties
PublikacjaThe oriented TiO2 nanotube arrays (NTs) are identified as a stable, active and recyclable photocatalytic surface. However, their photoactivity is strictly depended on morphology (especially length), which could be controlled by anodic oxidation parameters, including electrolyte properties. To control the morphology, were successfully synthesized a series of NTs by a novel approach where ionic liquid (IL), ethylammonium nitrate...
-
Detection of the Incoming Sound Direction Employing MEMS Microphones and the DSP
PublikacjaA 3D acoustic vector sensor based on MEMS microphones and its application to road traffic monitoring is presented in the paper. The sensor is constructed from three pairs of digital MEMS microphones, mounted on the orthogonal axes. Signals obtained from the microphones are used to compute sound intensity vectors in each direction. With this data, it is possible to compute the horizontal and vertical angle of an incoming sound....
-
Microporous Polyurethane Thin Layer as a Promising Scaffold for Tissue Engineering
PublikacjaThe literature describes that the most efficient cell penetration takes place at 200–500 µm depth of the scaffold. Many different scaffold fabrication techniques were described to reach these guidelines. One such technique is solvent casting particulate leaching (SC/PL). The main advantage of this technique is its simplicity and cost efficiency, while its main disadvantage is the scaffold thickness, which is usually not less than...
-
Polyurethane porous scaffolds (PPS) for soft tissue regenerative medicine applications
PublikacjaTissue engineering requires suitable polymeric scaffolds, which act as a physical support for regenerated tissue. A promising candidate might be polyurethane (PUR) scaffold, due to the ease of the PUR properties design, which can be adjusted directly to the intended purpose. In this study, we report a successful fabrication of porous polyurethane scaffolds (PPS) using solvent casting/particulate leaching technique combined with...
-
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
PublikacjaThe Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a...
-
Chitosan-Based Membranes as Gentamicin Carriers for Biomedical Applications — Influence of Chitosan Molecular Weight
PublikacjaOver the past decade, much attention has been paid to chitosan as a potential drug carrier because of its non-toxicity, biocompatibility, biodegradability and antibacterial properties. The effect of various chitosan characteristics on its ability to carry different antibiotics is discussed in the literature. In this work, we evaluated the influence of the different molecular weights of this polymer on its potential as an antibacterial...
-
Medium-sized cyclic bis(anisylphosphonothioyl)- disulfanes and their corresponding cyclic sulfane-structures and most characteristic reactions
PublikacjaCyclic 8-, 9-, 10-, and 12-membered bis(anisylphosphonothioyl)disulfanes were synthesized. Next, structurally related 7 to 9-membered cis and trans sulfanes were isolated as a result of sulfur atom extrusion from the parent cyclic disulfanes. The results of the desulfurization of the disulfanes were compared to the results obtained for desulfurization of the respective bis(anisylphosphodithioates). Cyclic disulfanes predominantly...
-
Bricks images dataset
Dane BadawczeThe set contains 200 images of various wooden bricks of various shapes and colors placed on a background (blanket) with some heart shaped patterns. Each photo is available in 300x300 and 224x224 pixels size in PNG format. Photos are divided in 10 classes – 8 types of bricks photographed form various angles + 2 additional classes (multiple bricks at...
-
Updating Finite Element Model of a Wind Turbine Blade Section Using Experimental Modal Analysis Results
PublikacjaThis paper presents selected results and aspects of themultidisciplinary and interdisciplinary research oriented for the experimental and numerical study of the structural dynamics of a bend-twist coupled full scale section of awind turbine blade structure.Themain goal of the conducted research is to validate finite elementmodel of themodified wind turbine blade section mounted in the flexible support structure accordingly to the...
-
Influence of Ionic Liquid Structure on Supported Ionic Liquid Membranes Effectiveness in Carbon Dioxide/Methane Separation
PublikacjaThis paper indicates the possibility of application of imidazolium ionic liquids immobilized in polymeric supports—supported ionic liquid membranes—in CO2 separation from gaseous streams (e.g., biogas). Imidazolium salts containing alkyl fluoride anions, bis(trifluoromethylsulfonyl)imide and trifluoromethanesulfonate, selectively separating CO2 were used. The permeability of CO2 through membranes was investigated under gas pressure...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublikacjaThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Comparison of 3D Point Cloud Completion Networks for High Altitude Lidar Scans of Buildings
PublikacjaHigh altitude lidar scans allow for rapid acquisition of big spatial data representing entire city blocks. Unfortunately, the raw point clouds acquired by this method are largely incomplete due to object occlusions and restrictions in scanning angles and sensor resolution, which can negatively affect the obtained results. In recent years, many new solutions for 3D point cloud completion have been created and tested on various objects;...
-
Determination of aminoglycoside antibiotics: current status and future trends
PublikacjaThe use of aminoglycoside antibiotics is prevalent in medicine and agriculture. Their overuse increases their mobility in the environment, resulting in a need for reliable methods for their determination in a variety of matrices. However, the properties of aminoglycosides, in particular their high polarity, make the development of such methods a non-trivial task, inciting researchers to tackle this complex issue from different...
-
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublikacjaThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublikacjaLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
Efficient RSS-Based DoA Estimation for ESPAR Antennas Using Multiplane SDR Calibration Approach
PublikacjaIn this paper, we have introduced a new method to improve overall efficiency of direction-of-arrival (DoA) estimation scheme relying on received signal strength (RSS) values measured at the output port of electronically steerable parasitic array radiator (ESPAR) antenna. The proposed approach uses software-defined radio (SDR) setup and power pattern cross-correlation (PPCC) estimator involving multiple calibration planes. By placing...
-
Biological processes modelling for MBR systems: A review of the state-of-the-art focusing on SMP and EPS
PublikacjaA mathematical correlation between biomass kinetic and membrane fouling can improve the understanding and spread of Membrane Bioreactor (MBR) technology, especially in solving the membrane fouling issues. On this behalf, this paper, produced by the International Water Association (IWA) Task Group on Membrane modelling and control, reviews the current state-of-the-art regarding the modelling of kinetic processes of biomass, focusing on...
-
"SKONTEKSTOWANE. zamieszkiwanie krajobrazów", dwa tryptyki malarskie, akryl/ podobrazie płócienne, materiał video
PublikacjaPoruszamy się w świecie przemieszanych znaczeń. Kierowani tradycją, doświadczeniem i intuicją przemierzamy przestrzenie odnosząc je do swojego domu. W każdy otaczający krajobraz podświadomie lub celowo wpisujemy siebie. Filtrujemy obraz, dźwięk i zapach włączając wartości niesione przez życie. Dom z marzeń, dom ze wspomnień, dom, do którego tęsknimy, nasz dom: wypełniają kadry i współtworzy historię odwiedzanych miejsc. Przedstawione...
-
Tropospheric delays derived from GNSS observations during the derecho event in Poland of 11th August 2017
Dane BadawczePropagation of global navigation satellite systems (GNSS) radio signals is disturbed by the current state of the Earth's atmosphere. For this reason, advances processing of GNSS signals can be used for investigation of the atmospheric condition. In case of troposphere, the GNSS signals allow for obtain information of tropospheric delay, which is mainly...
-
Microcapsules and their applications in pharmaceutical and food industry.
PublikacjaMicroencapsulation is a process in which tiny particles or droplets are surrounded by a coating or embedded in a homogeneous or heterogeneous matrix, to generate small capsules in size range from a few to few thousand micrometers. The material inside the microcapsule is referred to as the core, internal phase, or fill, whereas the wall is sometimes called shell, coating, wall material, or membrane. It has found application in...
-
Sanctions and their role in preventing the appropriation of the creditor’s property rights in bankruptcy proceedings–the case of Poland
PublikacjaThe aim of this paper is to fill the cognitive gap regarding the role of sanc-tions in the protection of a creditor’s property rights in the event of an entrepreneur insolvency. The impact of sanctions on transaction costs, including their identifica-tion and types, as well as the impact on the protection of creditor rights, has been poorly recognized in the subject literature to date. This article investigates...
-
The Motion Analysis of Attacus Atlas Rigid Wing
PublikacjaThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
Systems of General Grants for Local Governments in Selected EU Countries Against the Background of the General Theory of Fiscal Policy
PublikacjaFiscal policy, including its expenditure aspect, is often discussed and analysed from a variety of angles in the literature on public finances, undoubtedly due to the major importance of this topic. However, not all areas of the expenditure part of fiscal policy have been subjected to in-depth analysis. One of the less discussed tools of fiscal policy consists of general purpose transfers, which are a certain type of expenditure...
-
THE PROPERTIES OF NANOSILVER – DOPED NANOHYDROXYAPATITE COATING ON THE Ti13Zr13Nb ALLOY
PublikacjaThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed...
-
Superhydrophobic sponges based on green deep eutectic solvents for spill oil removal from water
PublikacjaThe paper described a new method for crude oil-water separation by means of superhydrophobic melamine sponges impregnated by deep eutectic solvents (MS-DES). Due to the numerous potential of two-component DES formation, simple and quick screening of 156 non-ionic deep eutectic solvents using COSMO-RS (Conductor-like Screening Model for Real Solvents) computational model was used. DES which were characterized by high solubility...
-
Cytocompatibility, antibacterial, and corrosion properties of chitosan/polymethacrylates and chitosan/poly(4‐vinylpyridine) smart coatings, electrophoretically deposited on nanosilver‐decorated titania nanotubes
PublikacjaThe development of novel implants subjected to surface modification to achieve high osteointegration properties at simultaneous antimicrobial activity is a highly current problem. This study involved different surface treatments of titanium surface, mainly by electrochemical oxidation to produce a nanotubular oxide layer (TNTs), a subsequent electrochemical reduction of silver nitrate and decoration of a nanotubular surface with...
-
An integrated geotechnical and geophysical investigation of landslide in Chira town, Ethiopia
PublikacjaLandslides pose a significant threat to infrastructure, property, and human lives in many regions worldwide, including Chira town in Ethiopia. This study presents an integrated geotechnical and geophysical investigation aimed at identifying the contributing factors to landslides in Chira town, Ethiopia, with a focus on a recent landslide event. The methodology employed a combination of geotechnical and geophysical techniques to...
-
Facilitated water transport in composite reduced graphene oxide pervaporation membranes for ethanol upgrading
PublikacjaHigh purity ethanol is one of the most sought-after renewable energy sources. However, standard production methods yield ethanol of insufficient quality. Membrane processes such as pervaporation are recognized as a viable method for upgrading ethanol. Their performance and selectivity depend solely on membrane employed. Hydrophilic polyvinyl alcohol (PVA) membranes are used industrially for this purpose, but there is a trade-off...
-
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
PublikacjaThis article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring...
-
Nonconventional 1,8-Diazafluoren-9-One Aggregates for Green Light Enhancement in Hybrid Biocompatible Media
PublikacjaOrganic aggregates currently play a prominent role, mainly for their unique optoelectronic properties in the aggregated state. Such properties can be related to the aggregates’ structure and the molecular packing mode. In the literature, we have well-established models of H and J aggregates defined based on the molecular exciton model. However, unconventional aggregates, the most unrecognized forms, have been generating interest...
-
Hydrothermal modification of TiO2 nanotubes in water and alkali metal electrolytes (LiNO3, NaNO3, KNO3) – Direct evidence for photocatalytic activity enhancement
PublikacjaThe influence of hydrothermal annealing (HA) of TiO2 nanotubes (TiO2-NTs) in various baths (H2O, LiNO3, NaNO3, KNO3 performed for 4 h, 24 h, 64 h), on their photocatalytic and photoelectrocatalytic properties, was studied. The use of electrolytes was to enable the monitoring of photoactivity changes as a result of the expected impact on the population of hydroxyl groups on the surface. The assumption turned out to be correct and...
-
Polyurethanes Crosslinked with Poly(vinyl alcohol) as a Slowly-Degradable and Hydrophilic Materials of Potential Use in Regenerative Medicine
PublikacjaNovel, slowly-degradable and hydrophilic materials with proper mechanical properties and surface characteristics are in great demand within the biomedical field. In this paper, the design, synthesis, and characterization of polyurethanes (PUR) crosslinked with poly(vinyl alcohol) (PVA) as a new proposition for regenerative medicine is described. PVA-crosslinked PURs were synthesized by a two-step polymerization performed in a solvent...
-
On the relationship between the structural and volumetric properties of solvated metal ions in O-donor solvents using new structural data in amide solvents
PublikacjaThe structures of the N,N-dimethylformamide (dmf), N,N-dimethylacetamide (dma), and N,N-dimethylpropionamide (dmp) solvated strontium and barium ions have been determined in solution using large angle X-ray scattering and EXAFS spectroscopy. The strontium ion has a mean coordination number (CN) between 6.2 and 6.8, and the barium ion has a mean CN between 7.1 and 7.8 in these amide solvents. The non-integer numbers indicates that...
-
Calculation of the Effects of Implementing a DSM Electricity Demand Management Strategy Using the Example of Analysis of Changes in the Power System Load
PublikacjaThe paper presents the impact of implementing Demand Side Management (DSM) solutions through proper management and control of the process of charging and discharging electric car batteries. As a result, the daily load curves were shaped so as to fill valleys and cut down peaks. Therefore, the implementation of power demand management solutions had a significant impact on the power system operation. The impact of DSM solutions manifested...
-
Do Judges’ Delegations Affect Judicial Performance? A Transition Economy Evidence
PublikacjaThe aim of this study is to discern whether, by delegating judges from the court to the Ministry of Justice, the Minister of Justice influences the results of courts in terms of adjudication. The study used a unique set of data for the Polish judicial system over a period of five years. The research results indicate that there are three reasons for delegating judges. Firstly, the delegation system serves to fill staff shortages...
-
Gendered entrepreneurship and its impact on firm innovativeness - a literature review.
PublikacjaEntrepreneurs gain a lot of attention in recent decades. Even if a precise definition of entrepreneur and entrepreneurship remains problematic, it is clear that there is a strong link between entrepreneurship and innovativeness, as well as between entrepreneur and innovation. In the current era of globalisation, the importance of innovations is as great as never before. And so is the importance of innovativeness determinants. Investigating...
-
The American Sign Language alphabet
Dane BadawczeThe American Sign Language dataset contains all static letters of the American alphabet, meaning those that do not require movement to perform (the entire alphabet except for the letters 'J' and 'Z', which are dynamic and require hand movement).
-
Application of acoustic emission metod for measurement of joint gap and cartilage surfaces
PublikacjaW artykule przedstawiono zastosowanie emisji akustycznej do lokalizacji wczesnych uszkodzeń stawu biodrowego lub kolanowego człowieka. Ponadto metoda ta służy do pomiaru wysokości szczeliny stawu oraz struktury geometrycznej powierzchni chrząstki stawowej. Jest to metoda nieinwazyjna. Pomiary metodą emisji akustycznej stosujemy na ogół w materiałach, w których energia sprężysta zmienia się nagle. Takie zmiany energii mogą być...
-
THE RESEARCH ON EGNOS SYSTEM IN CONTEXT OF THE ABILITY TO DETERMINE THE SHIP’S HULL SPATIAL ORIENTATION
PublikacjaThe European Geostationary Navigation Overlay Service (EGNOS) thanks to geostationary satellites covers an area of whole Europe, including Baltic and North Sea. It allows to fix the coordinates of object position with typical absolute accuracy of 1,5 m. Previous research have shown that relative accuracy is usually higher than absolute one [Nowak A., 2010, Nowak A., 2011], so probably it could be possible to use EGNOS to determine...
-
Joint experimental and theoretical study on low-energy elastic electron scattering by gaseous alkynes: Differential cross sections, shape resonances, and methylation effects
PublikacjaA detailed comparison of experimental and theoretical elastic cross sections for low-energy electron scattering by ethyne, taken earlier in our group by Gauf et al. [Phys. Rev. A 87, 012710 (2013)], and some of its methylated derivatives, propyne, and the isomers 1-butyne and 2-butyne, taken here, are presented. The present differential cross sections were measured at incident electron energies ranging from 1 eV to 30 eV and...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublikacjaThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
Laser-assisted modification of titanium dioxide nanotubes in a tilted mode as surface modification and patterning strategy
PublikacjaElectrochemical anodization is regarded as a facile and easily scalable fabrication method of titania nanotubes (TiO2NTs). However, due to the extended duration of calcination and further modifications, much faster alternatives are highly required. As a response to growing interest in laser modification of nanotube arrays, a comprehensive investigation of pulsed-laser irradiation and its effect onto TiO2NT properties has been carried out....
-
Principles and Practices of Corporate Governance in the Global Economy
PublikacjaThe book places ownership at the centre of all relevant choices that the company makes. In particular, it addresses the issue of governance from the perspective of ownership, and in a broader and more articulated sense than most Anglo-Saxon studies do. The authors analyse the relationship between ownership, governance, and corporate strategy, with a dual objective. On the one hand, the aim is to identify the consistency relationships...
-
The Development of a Conceptual Framework for Knowledge Sharing in Agile IT Projects
PublikacjaOrganizations must adapt their resources to meet the challenges associated with changes in the work environment in order to remain competitive in the information era. Several research findings identify knowledge sharing as a means for an organization to improve its competitiveness. Knowledge sharing can be defined in a variety of ways, but it essentially refers to the exchange of knowledge from an information giver to an information...
-
A new approach to determination of the two-mass model parameters of railway current collector
PublikacjaThe paper presents two mathematical models of railway current collectors both with two degrees of freedom. The first one, hereinafter Pantograph Articulated Model (PAM), has one degree of freedom in rotational motion and the second degree of freedom in translational motion. The second model, called henceforth as Pantograph Reference Model (PRM), has both degrees of freedom in translational motion. Differential equations of the...
-
A new approach to determination of the two-mass model parameters of railway current collector
PublikacjaThe paper presents two mathematical models of railway current collectors both with two degrees of freedom. The first one, hereinafter Pantograph Articulated Model (PAM), has one degree of freedom in rotational motion and the second degree of freedom in translational motion. The second model, called henceforth as Pantograph Reference Model (PRM), has both degrees of freedom in translational motion. Differential equations of the...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublikacjaThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
Proposal of New Tracer Concentration Model in Lung PCT Study Comparison with Commonly Used Gamma-variate Model
PublikacjaPerfusion computed tomography (pCT) is one of the methods that enable non-invasive imaging of the hemodynamics of organs and tissues. On the basis of pCT measurements, perfusion parameters such as blood flow (BF), blood volume (BV), mean transit time (MTT) and permeability surface (PS) are calculated and then used for quantitative evaluation of the tissue condition. To calculate perfusion parameters it is necessary to approximate...