Filtry
wszystkich: 1736
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CA-LOOPING
-
Emissivity of the one-plate lapping machine tool
PublikacjaPrzedstawiono wyniki badań własnych emisyjności docieraka żeliwnego docierarki jednotarczowej. Omówiono konstrukcje produkowanych docierarek jednotarczowych wyposażonych w system kontroli temperatury lub chłodzenia tarczy docierającej. Podano warunki pomiarów temperatury przy użyciu kamery termowizyjnej typu V-20II firmy VIGO System S.A.
-
Modeling of the internal combustion engine cooling system
PublikacjaThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Polaron hopping conduction in manganese borosilicate glass
PublikacjaA study on a novel material - manganese borosilicate glass without alkali metals, was reported. It was found that the obtained samples containing high amount of manganese oxide (60MnO–xSiO2–(40 − x)B2O3, x = 5, 10, 15, 20 and 30 mol%) were amorphous and homogeneous. XPS measurements showed that most of manganese ions are at oxidation level of Mn2 + ions and the mean oxidation level slightly moves toward higher value, with increasing...
-
Scheelite-Type Wide-Bandgap ABO4 Compounds (A = Ca, Sr, and Ba; B = Mo and W) as Potential Photocatalysts for Water Treatment
PublikacjaIn the present study, alkaline-earth metal scheelite-type compounds ABO4 (A = Ca, Sr, Ba, B = Mo, W) synthesized by a hydrothermal method were systematically studied. The as-obtained photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer-Emmett-Teller surface area analysis (BET), UV–Vis diffuse reflectance spectroscopy (DR/UV-Vis), photoluminescence, and thermoluminescence (TL)...
-
Cobalt doping of nickel ferrites via sol gel approach: effect of doping on the structural and dielectric properties
Publikacja -
Solid phase extraction with flame atomic absorption spectrometry for determination of traces of Ca, K, Mg and Na in quality control of white sugar
Publikacja -
Test loading of the longest span arch bridge in Poland
PublikacjaBridge structures undergo thorough examination during test loading before they come into use. The aim of the examination is to check the correctness of the working structure and construction design assumptions. Test loading on the bridge is preceded by examination specification. This paper describes computational model and test loading results carried out during examibation of the bridge over the Vistula within the bypass of Puławy...
-
Microgrinding of flat surfaces on single-disc lapping machine
PublikacjaW pracy przedstawiono możliwości zastosowania specjalnych narzędzi do mikroszlifowania na docierarce jednotarczowej. Jedno z zastosowanych narzędzi posiada warstwę ścierniwa diamentowego (D64) nałożoną metodą galwaniczną. Drugie przetestowane narzędzie zbudowane zostało z diamentowych pastylek ściernych (D3/2). Przedstawiono analizę kinematyczną i wyniki ubytku materiałowego oraz osiągnięte parametry chropowatości.
-
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaW pracy przedstawiono model zużycia narzędzia w docieraniu dwutarczowym. Wyprowadzono równania opisujące kontakt przedmiotu z narzędziem. Przedstawiono wyniki analiz symulacyjnych dla różnych parametrów kinematycznych - dla układu współbieżnego i przeciwbieżnego.
-
Probability of flooding a compartment (the pi factor) - a critique and a proposal
PublikacjaArtykuł podaje krytyczny przegląd stanu wiedzy dot. obliczania prawdopodobirństwa zatopienia przedziału (mnożnika pi), ze szczególnym uwzględnieniem projektu badawczego ''Harder'' oraz podaje poprawne rozwiązanie dotyczące tego mnożnika. Kończy się propozycją przepisu do zamieszczenia w konwencji SOLAS.
-
Influence of aggregates angularity on the locking point of asphalt mixtures
Publikacja -
Technological aspects of microgrinding with single-disc lapping kinematics
PublikacjaPrzedstawiono wyniki badań mikroszlifowania powierzchni płaskich na docierarce jednotarczowej. Badano stan powierzchni narzędzia wykonanego na bazie mikroziaren diamentowych D65/50 naniesionych galwanicznie na podłoże stalowe. Analizowano wydajność obróbki oraz chropowatość powierzchni elementów ze stali 18G2A.
-
Microgrinding of flat surfaces on a single-disc lapping machine
PublikacjaW referacie przedstawiono wyniki badań eksperymentalnych mikroszlifowania z kinematyką docierania jednotarczowego. Przedstawiono propozycję narzędzia z wkładkami ściernymi z ziarnem diamentowym D3/2 i spoiwem żywicznym. Omówiono kinematykę docierania jednotarczowego i sposób oceny krzywizny rys obróbkowych.
-
Analysis of machining marks curvature in single disk lapping
PublikacjaW referacie przedstawiono wyniki badań symulacyjnych i eksperymentalnych dotyczących wyznaczania i oceny krzywizny śladów obróbkowych po obróbce mikroszlifowaniem z kinematyką docierania jednotarczowego.
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublikacjaThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
A System for Cooling Electronic Elements with EHD Coolant Flow
PublikacjaA system for cooling electronic components where the liquid coolant flow is forced with ion-drag type EHD micropumps was tested.
-
Experimental and theoretical investigation of microjet cooling in metalurgical applications
PublikacjaW pracy zaprezentowano model wrzącej strugi uderzającej o powierzchnię i wytwarzającej cienki film cieczowy, w którym tworzą się pęcherzyki pary.
-
The automation of test stand for engine cooling system testing
PublikacjaW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
Machining of the flat surfaces with abrasive-metallic lapping tools.
PublikacjaPrzedstawiono konstrukcje narzędzi ścierno-metalowych do obróbki powierzchni płaskich na docierarkach jednotarczowych. Przeprowadzono badania wydajności i jakości powierzchni elementów ceramicznych o małych gabarytach.
-
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaPrzedstawiono założenia modelowe do wyznaczenia zużycia profilowego narzędzia w docieraniu dwutarczowym. Rozkłady istotnych czynników kinematycznych (prędkości docierania i przyspieszenia stycznego) wpływających na zużycie docieraka zaprezentowane zostały dla różnych typów zakreślanych trajektorii.
-
An approach to fatigue assessment of metals under biharmonic loading.
PublikacjaRozpatrywane są kryteria nieograniczonej i ograniczonej trwałości zmęczeniowej metalicznych elementów poddanych biharmonicznemu naprężeniu, którego jedna składowa ma niską częstość. Założono, że składowa ta może być traktowana jako wolno zmieniające się w czasie naprężenie średnie. Kryteria zmęczeniowe sformułowano za pomocą równań Goodmana i Soderberga. Dyskutowane są wyniki przykładowych obliczeń.
-
Impact of thermal loading into the structural performance of ships: A review
PublikacjaThe presented study reviews the recent advances done regarding the impact of thermal loading on the structural performance of ships. Firstly, the studies related to the mechanical and thermal properties of typical materials used in shipbuilding are outlined. Secondly, a brief introduction to the heat transfer analysis, Finite Element modelling and thermal stresses is provided. Finally, the review of papers dealing with the structural...
-
Random field model of foundations at the example of continuous footing
PublikacjaThe purpose of the paper is to indicate an efficient method of foundation settlement analysis taking into account the variability of soil properties. The impact of the random variable distribution (Gauss or Lognormal) describing soil stiffness on foundation deposits was assessed. The Monte Carlo simulation method was applied in the computations. The settlements of the strip foundation with the subsoil described by a single random...
-
Numerical simulation of extreme flooding in a built-up area
PublikacjaPrzedstawiono dwie numeryczne symulacje propagacji gwałtownej fali powodziowej przez schematyczny model obszaru zabudowanego. Do obliczeń wykorzystano równania przepływu wody płytkiej. Wyniki obliczeń porównano z dostępnymi pomiarami wykonanymi w laboratorium hydraulicznym ENEL-CESI w Mediolanie. Uzyskano zadowalającą zgodność symulacji z eksperymentami.
-
Microgrinding of flat surfaces on single-disk lapping machine
PublikacjaW pracy przedstawiono wyniki badań mikroszlifowania z kinematyką docierania w układzie jednotarczowym z wykorzystaniem nowego narzędzia wykonanego z pastylek ściernych z ziarnem diamentowym (D3/2) i spoiwem żywicznym. Zakres pracy obejmował przeprowadzenie badań eksperymentalnych i modelowych związanych z analizą promienia krzywizny rys obróbkowych.
-
A novel degree-hour method for rational design loading
PublikacjaCooling degree-hours (CDH) received the broadest application in evaluation of the ambient air cooling efficiency in power engineering (engine intake air cooling systems) and air conditioning. The current CDH numbers are defined as a drop in air temperature multiplied by associated time duration of performance and their summarized annual number is used to estimate the annual effect achieved due to sucked air cooling in power plants...
-
Tendencies in abrasive machining with lapping kinematics - experimental studies
PublikacjaW pracy przedstawiono tendencje rozwoju obróbki ściernej z wykorzystaniem kinematyki docierania. Zaprezentowano wyniki badań szlifowania specjalnymi narzędziami w układzie docierarki jedno- i dwutarczowej.
-
Strength analysis of container ship subjected to torsional loading
PublikacjaThe objective of this work is to investigate the torsional response of a container ship, with particular consideration of the warping effect. Two different models are investigated. In the first case, the full length model of a ship is analyzed and a distributed load is applied with the use of a novel approach. The model is supported in the torsional centre of the cross-section, which is derived analytically. In the second case,...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Novel Desorber for Online Drilling Mud Gas Logging
PublikacjaThis work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was...
-
Active management of equipment cooling in hoteling data centers
PublikacjaHoteling data centers are designated for housing computing and storage units of many, usually small customers, as opposed to traditional data centers supporting own computing and storage resources of a bigger company. One of the services to be provided to consumer’s equipment is cooling. Cooling in data centers is prevalently achieved by circulating air in computer room. Efficient cooling requires delivering cold air from central...
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublikacjaPrzedstawiono zbudowane stanowisko do badań wymuszonego dawkowania zawiesiny ściernej w procesie jednostronnego docierania powierzchni płaskich. Podano przyjęty program badań oraz sposób opracowania wyników realizowanych eksperymentów.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublikacjaPrzedstawiono zbudowane stanowisko badawcze umożliwiające wymuszone dozowanie zawiesiny ściernej w operacji docierania jednotarczowego powierzchni płaskich. Podano program badań własnych oraz sposób opracowania otrzymanych wyników realizowanych eksperymentów.
-
Wear of the tool in double-disc lapping of silicon wafers
PublikacjaPrzedstawiono założenia modelowe do określania zużycia narzędzia w docieraniu krzemowych płytek półprzewodnikowych. Obliczenia zostały wykonane dla różnych parametrów kinematycznych, wpływających na zużycie narzędzia w określonych jego obszarach.
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublikacjaPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
System of monitoring of the Forest Opera in Sopot structure and roofing
PublikacjaThe authors present a solution realized in Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland) in connection with the modernization and construction of a new roof. The complicated structure of the roof of the facility and the used covering in form of membrane made of technical fabric required (for security reasons) to install the unit of devices allowing for the continuous geodetic monitoring of the facility. Monitoring...
-
Effects of cooking on the bioactivity of lotus roots and white onions
PublikacjaW pracy przedstawiono wyniki badań wpływu obróbki termicznej (gotowanie) na zawartość związków bioaktywnych i potencjału przeciwutleniającego korzenia lotosu i cebuli białej.Wyniki badań jednoznacznie wskazują na fakt, że taki proces obróbki wpływa w znaczącym stopniu na spadek stężenia związków bioaktywnych i potencjału przeciwutleniającego.
-
Determining the conditions for temperature measurements during flat lapping
PublikacjaPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Bioaccumulation of alkaline soil metals (Ca, Mg) and heavy metals (Cd, Ni, Pb) patterns expressed by freshwater species of Ulva (Wielkopolska, Poland)
Publikacja -
Allelic length of a CA dinucleotide repeat in theegfr gene correlates with the frequency of amplifications of this sequence—first results of an inter-ethnic breast cancer study
Publikacja -
Indium doping in SrCeO3 proton-conducting perovskites
Publikacja -
Efficacy of coping with work-related stress by firemen
PublikacjaThe aim of this study was efficacy of coping with work-related stress by firemen with reference to subjective health evaluation. Theoretical model of process of stress by Lazarus was applied. The group consistent of 230 line-duty firemen. Participation in traumatic events and sense of coherence both directly and indirectly, by stress, affected the health among firemen. In stress confrontation a wider array of task and emotional...
-
Looking for New Ideas of Public Space - Public Space Projects in Gdansk Reinforced by Art Activities
Publikacja -
Looking for the Optimal Location of an Eco-District within a Metropolitan Area: The Case of Tricity Metropolitan Area
PublikacjaCompact housing structures located in city centers are considered to be the most energy and environmentally eective, mainly due to the access to services, transport networks and municipal infrastructures. There is the question of why so many of the acknowledged ecological housing complexes are located on the outskirts of cities or suburbs. Numerous cities decide to introduce strategies either to densify city centers, hoping to...
-
Looking for New Ideas of Public Space – Public Space Projects in Gdansk Reinforced by Art Activities
PublikacjaRevitalization of public open spaces is a complex enterprise in Poland in terms of the art, cultural andinformation aspects of this process. Simultaneously the public space should play an important role whenbuilding the quality of revitalization programs and the quality of city development. The new art and culturalactivities are the revitalization tools, which are also the good examples of bottom up ideas helping to start aprocess...