Wyniki wyszukiwania dla: CHROMIUM EVAPORATION
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Wpływ podwyższonych temperatur na napawane warstwy na bazie kobaltu = The elevated temperatures influence on the cobalt base cladding layer
Publikacjaw pracy przeanalizowano wpływ temperatur utleniania (850, 950 i 110 stopni C) na mikrostrukturę i twardośc napawanych plazmowo warstw zykonanych z proszku na bazie kobaltu zdodatkiem 28,8% chromu, 4,9% wolframu, 2,2% niklu, 2,09% żelaza, 1,2% krzemu i 1,2% węgla. W wyniku utleniania na powierzchni napoiny powstaje warstwa tlenku chromu stanowiaca dobrą ochronę w niższych temperaturach, jednak w temperaturach wyższych ulega ona...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublikacjaIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
FEM approach to modeling of an irregular trabecular structure
PublikacjaThe aim of the study is elaboration of a method for creating irregular scaffolds that can be used to model the behaviour of trabecular bone placed in the proximal epiphysis of the femur. The scope of the study encompasses creating six numerical models of irregular scaffolds (two solid irregular scaffolds, two shell irregular scaffolds and two shell irregular scaffolds with fortification) and performing numerical analysis of the...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublikacjaThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Development of Microstructured Carbon Coatings by Substrate-Catalytic CVD
PublikacjaCarbon nanostructured films were synthesized by chemical vapor deposition (CVD) on H18 stainless steel (AISI 440C) sheets with an H2/CH4/N2 gas mixture at various substrate temperatures. During the synthesis, the iron and chromium oxide layer was formed between the steel and carbonaceous layer. The carbon films exhibited wall-like and spherical morphologies and structures, as characterized by scanning electron microscopy and Raman...
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublikacjaA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Water Resources Management 2022/2023
Kursy OnlineWater Resources Management as defined for purpose of this course includes both water use and water excess management. The fundamental water resources engineering processes are the hydrologic processes and the hydraulic processes. The common threads that relate to the explanation of these processes are the fundamentals of fluid mechanics. The hydrologic processes include rainfall, evaporation, infiltration, rainfall-runoff and routing,...
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublikacjaThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Accumulation of radioisotopes and heavy metals in selected species of mushrooms
PublikacjaSeven species of forest mushrooms from different regions of Poland (edible: Imleria badia, Cantharellus cibarius, Xerocomus subtomentosus, Suillus luteus and inedible by humans but being food for animals: Paxillus involutus, Tylopilus felleus and Russula emetica) were analyzed for radioisotope activity (Cs-137, K-40, Bi-214 and Pb-210) as well as concentrations of heavy metals (aluminum, chromium, cadmium, manganese, iron, lead,...
-
Ceramic composites for single-layer fuel cells
PublikacjaComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublikacjaDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Quadratic Cohen representations in spectral analysis of serration process in Al–Mg alloys
PublikacjaImportant from mechanical point of view the Portevin–Le Chatelier serration phenomenon is being characterized by a complicated spectral profile. As a typical example of nonstationary processes it demands a special treatment allowing to follow the evolution of energy of stress fluctuations as a function of strain. The authors suggest the utilization of a compact system of quadratic transformations, known as Cohen class, as a technique...
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublikacjaIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...
-
Morphology, surface properties and photocatalytic activity of the bismuth oxyhalides semiconductors prepared by ionic liquid assisted solvothermal method
PublikacjaThis is the first report of the effect of the ILs cation type (imidazolium, pyridinium and pyrrolidinium) on the morphology, surface properties and photoactivity of BiOX semiconductors type obtained by solvothermal method in glycerol. The various ionic liquids (IL) cation type as a halogen source and templating agent for the synthesis of the bismuth oxyhalides nanoparticles has been systematically investigated. The role of ILs...
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublikacjaThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
EXAMINATION OF SOL-GEL DERIVED HYDROXYAPATITE ENHANCED WITH SILVER NANOPARTICLES USING OCT AND RAMAN SPECTROSCOPY
PublikacjaHydroxyapatite (HAp) has been attracting widespread interest in medical applications. In a form of coating, it enables to create a durable bond between an implant and surrounding bone tissues. With addition of silver nanoparticles HAp should also provide antibacterial activity. The aim of this research was to evaluate the composition of hydroxyapatite with silver nanoparticles in a non-destructive and non-contact way. For control measurements...
-
Prediction of coking dynamics for wet coal charge
PublikacjaA one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal...
-
Novel Cold Crucible Ultrasonic Atomization Powder Production Method for 3D Printing
Publikacja: A new powder production method has been developed to speed up the search for novel alloys for additive manufacturing. The technique involves an ultrasonically agitated cold crucible installed at the top of a 20 kHz ultrasonic sonotrode. The material is melted with an electric arc and undergoes pulverization with standing wave vibrations. Several different alloys in various forms, including noble and metallic glass alloys, were...
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublikacjaConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublikacjaIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Comment on "Measurements without probabilities in the final state proposal"
PublikacjaThe final state proposal [G.T. Horowitz and J.M. Maldacena, J. High Energy Phys.2004(2),8 (2004)] is an attempt to relax the apparent tension betweenstring theory and semiclassicalarguments regarding the unitarity of black hole evaporation. The authors of [R. Bousso and D.Stanford, Phys. Rev. D89, 044038 (2014)] analyze thought experiments where an infalling observerfirst verifies the entanglement between early and late Hawking...
-
Możliwości ograniczenia zużycia energii napędowej urządzeń przez optymalizację doboru wymienników ciepła, właściwą konfigurację i kontrolę przepływu płynów roboczych
PublikacjaArtykuł poświęcony możliwości ograniczenia zużycia energii napędowej urządzeń na drodze optymalizacji doboru wymienników ciepła, właściwej konfiguracji i kontroli przepływu płynów roboczych. Przedstawiono w nim ocenę zużycia energii w systemach energetycznych o największej energochłonności w realiach Polski. Zwrócono uwagę na możliwość wykorzystania wymienników ciepła o wysokiej efektywności dla zmniejszenia oporu przenoszenia...
-
Evaluation of the Effectiveness of Methods for Delimitation of the Boundaries of Registered Parcels in the Process of Modernization of Land and Building Registration
PublikacjaIn the article, a comparative analysis of two methods for delimitation of the boundaries of registered parcels was carried out: the method of direct measurement in the field and the photogrammetric method. One of the analyzed factors was the attendance of parcels’ owners during the development of boundary recognition agreements. Research has shown that in this aspect the method of direct measurement...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublikacjaA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Metal dusting in CCR platforming unit
PublikacjaPrzedstawiono mechanizm pylenia metalu w stali 9Cr-1Mo w instalacji platformingu CCR, na postawie badań rury podgrzewacza wsadu po 10 latach pracy, przy temperaturze metalu koło 600C. W badaniach wykorzystano techniki elektronowej mikroskopii skaningowej, dyfrakcji rentgenowskiej i mikroanalizy rentgenowskiej. Wykazano, że dyfuzji wegla w głąb stali toarzyszy odrdzeniowa dyfuzja pierwiastków węglikotwórczych - chromu i molibdenu....
-
Metal dusting in CCR platforming unit
PublikacjaPrzedstawiono mechanizm pylenia metalu w stali 9Cr-1Mo w instalacji platformingu CCR, na postawie badań rury podgrzewacza wsadu po 10 latach pracy, przy temperaturze metalu koło 600C. W badaniach wykorzystano techniki elektronowej mikroskopii skaningowej, dyfrakcji rentgenowskiej i mikroanalizy rentgenowskiej. Wykazano, że dyfuzji wegla w głąb stali toarzyszy odrdzeniowa dyfuzja pierwiastków węglikotwórczych - chromu i molibdenu....
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of water cooled materia
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of reference material materia (transverse direction)
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of reference material materia (longitudinal direction)
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of naturally colled material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of water cooled material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of reference material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of naturally cooled material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Identification of intermetallic phases in the structure of austenitic steel with use of Scanning Kelvin Probe Microscopy
Dane BadawczeDelta ferrite is formed in austenitic steels during the solidification of the alloy and its welds. It can also occur as a stable phase in any temperature range in high-alloy austenitic-ferritic steels. Depending on the amount, it can change into gamma and sigma phases and into ferrite with variable chromium content. The main role of delta ferrite in...
-
Preservation and Storage of Water Samples
PublikacjaOpisano metody utrwalania i przechowywanie próbek wody w celu oznaczenia zwiazków nieorganicznych, przedyskutowano wady i zalety poszczególnych metod. Omówiono utrwalanie i przechowywanie próbek wody przed wykonaniem analizy specjacyjnej związków arsenu, chromu, rteci, selenu i cyny. Omówiono również utrwalanie i przechowywanie próbek wody przy oznaczaniu związków organicznych.
-
Wpływ grubości porowatej powłoki ceramicznej na proces docierania.
PublikacjaW pracy omówiono proces docierania porowatej powłoki ceramicznej (trójtlenku chromu) w rozróżnieniu dla trzech wstępnych grubości naniesionych powłok. Przeanalizowano wpływ tego parametru na przebieg procesu i rezultaty obróbki. Wyniki badań wykazały istotny wpływ początkowej grubości powłok, w których porowatość charakteryzowała się niejednorodnością na przekroju poprzecznym badanych powłok.
-
Badania połączeń spawanych rurociągu wody pitnej we Włocławku, ang. Welding joints tests in drinking water pipeline.
PublikacjaCelem badań opisanych w pracy było określenie przyczyn korozji powstałej w strefie wpływu ciepła (SWC) w obwodowych połączeniach spawanych w rurociągu wody pitnej. Materiałem, z którego wykonano rurociąg to stal 304/304L. W obszarze złącza spawanego stwierdzono wżery inicjowane od niezgodności geometrycznych, gdzie mogły gromadzić się osady zwiększające udział chlorków bezpośrednio przy powierzchni rury, promujące tym procesy korozyjne....
-
Investigation of environmental influences to the precise GNNS solutions
PublikacjaThe results presented in this paper concern investigation of environmental influences to GNNS coordinates on the example of ASG-EUPOS network. The problem of the impact of environmental effects is crucial for observing gravity. Satellite systems are not as susceptible to changes in local hydrology or atmospheric effects, although significant influences are clearly visible in the change of coordinates. The authors analyzed daily...
-
Effect of Cr and Mn doping on ferroelectric and dielectric properties of Li1.72Na0.28Ge4O9 single crystals
PublikacjaLi1.72Na0.28Ge4O9 single crystals pure and slightly doped with chromium and manganese, obtained by Czochralski growth, were investigated for their ferroelectric and dielectric properties. The change in stoichometry of Li2− x Na x Ge4O9 (x = 0.28) crystals doped with Cr and Mn (0.1 mol.%) had an influence on the value of ferroelectric-to-paraelectric phase transition temperature, T c. The applied doping affects the T c value by...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Investigation and operation problems of metal tanks in Poland
PublikacjaThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Evaluating Gelatin-Based Films with Graphene Nanoparticles for Wound Healing Applications
PublikacjaIn this study, gelatin-based films containing graphene nanoparticles were obtained. Nanoparticles were taken from four chosen commercial graphene nanoplatelets with different surface areas, such as 150 m2/g, 300 m2/g, 500 m2/g, and 750 m2/g, obtained in different conditions. Their morphology was observed using SEM with STEM mode; porosity, Raman spectra and elemental analysis were checked; and biological properties, such as hemolysis...
-
Piotr Konieczka prof. dr hab. inż.
Osoby