Wyszukiwarka
Filtry
wszystkich: 1068
-
Katalog
- Publikacje 850 wyników po odfiltrowaniu
- Czasopisma 8 wyników po odfiltrowaniu
- Konferencje 2 wyników po odfiltrowaniu
- Osoby 24 wyników po odfiltrowaniu
- Projekty 2 wyników po odfiltrowaniu
- Aparatura Badawcza 1 wyników po odfiltrowaniu
- Kursy Online 16 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 164 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: INTERFACIAL SLIDING
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 10MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
Interface analysis of compatibilized polymer blends
PublikacjaThis chapter seeks to address the interface location in the compatibilized polymer blends and paves the way for quantitative analysis of interface in terms of interfacial tension and interfacial adhesion to provide support for understanding the relationship between morphology and ultimate properties in the compatibilized polymer blends through the lens of interface. Since understanding and analysis of interfacial phenomena in the...
-
A method for evaluating the performance of a marine piston internal combustion engine used as the main engine on a ship during its voyage in different sailing conditions
PublikacjaPrzedstawiono metodę oceny działania tłokowych silników spalinowych napędu głównego staków morskich, nazywanych silnikami głównymi, działających w typowych warunkach ich eksploatacji. Warunki te zostały opisane z uwzględnieniem pola osiągów tego rodzaju silników. Metoda ta umożliwia obliczenie wartości działania w wyniku zastosowania rachunku całkowego. Znamienne jest to, że działanie wspomnianych silników spalinowych zostało przyrównane...
-
Optical and structural properties of polycrystalline CVD diamond films grown on fused silica optical fibres pre-treated by high-power sonication seeding
PublikacjaIn this paper, the growth of polycrystalline chemical vapour deposition (CVD) diamond thin films on fused silica optical fibres has been investigated. The research results show that the effective substrate seeding process can lower defect nucleation, and it simultaneously increases surface encapsulation. However, the growth process on glass requires high seeding density. The effects of suspension type and ultrasonic power were...
-
Mariusz Kaczmarek dr hab. inż.
OsobyReceived M.Sc., Eng. in Electronics in 1995 from Gdansk University of Technology, Ph.D. in Medical Electronics in 2003 and habilitation in Biocybernetics and Biomedical Engineering in 2017. He was an investigator in about 13 projects receiving a number of awards, including four best papers, practical innovations (7 medals and awards) and also the Andronicos G. Kantsios Award and Siemens Award. Main research activities: the issues...
-
Mo-P5:335 Influence of life style knowledge on the occurrence of cardiovascular risk factors in adults living in Krakow - South Poland
Publikacja -
Exploring educational traditions and experiences of block residents engaging in urban food self-production: a case study of Urban Living Lab
Publikacja -
<p>Analysis of the degree of acceptance of illness among older adults living in a nursing home undergoing rehabilitation – an observational study</p>
Publikacja -
Costs and cost‐effectiveness of the meeting centres support programme for people living with dementia and carers in Italy, Poland and the UK: The MEETINGDEM study
Publikacja -
Towards evaluation of the Second Generation Intact Stability Criteria - examination of a fishing vessel vulnerability to surf-riding, based on historical capsizing
PublikacjaThe Second Generation Intact Stability Criteria (SGISC) are the latest achievements in the field of intact ship stability assessment. The criteria are the result of massive international cooperative efforts and extensive research that lasted more than 15 years. Even though they are based on a solid scientific foundation, the trial period has commenced to collect user experience and further validation. One of possible approaches...
-
Impact of the “Sling Shot” Supportive Device on Upper-Body Neuromuscular Activity during the Bench Press Exercise
Publikacja -
DLC coating in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h. The test was augmented...
-
DLC coating in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h. The test was augmented...
-
Revitalisation Living Lab as a Format to Accelerate an Energy Transition in Polish Rural Areas: The Case Studies of Metropolitan Outskirts Gdańsk-Orunia and Lubań
PublikacjaThe paper deals with the issue of energy transition in the revitalization process dedicated to the rural and semi-rural areas of the Pomerania Region (PR). Two distinct areas, located in sub- and ex-urban zones of the Gdańsk-Gdynia-Sopot Metropolitan Area (OMGGS), in which bottom-up community initiatives have been playing a key role in the transformation, have been focused on. The village of Lubań (Municipality of Nowa Karczma)...
-
A Comparison of Electromyographic Inter-Limb Asymmetry during a Standard versus a Sling Shot Assisted Bench Press Exercise
Publikacja -
An Analysis of the Relationship between the Architecture and the Structure of a Vessel on the Example of the Reconstruction Design Process of the Historical Sailing Yacht "General Zaruski" Carried Out between 2009 and 2012
PublikacjaThe article analyzes the relation between architecture and structure of a vessel on the example of the reconstruction design of a wooden sailing yacht "General Zaruski" built in Ekanӓs, Sweden in 1939. Based on the documentation of "Kaparen" (sister yacht), "Mloda Gwardia" (ex "General Zaruski") and the reconstruction classification project made by the authors, the impact of functional, spatial and aesthetic design objectives (e.g....
-
In Situ Random Microseeding and Streak Seeding Used for Growth of Crystals of Cold-Adapted beta-D-Galactosidases: Crystal Structure of betaDG from Arthrobacter sp. 32cB
PublikacjaThere is an increasing demand for cold-adapted enzymes in a wide range of industrial branches. Nevertheless, structural information about them is still scarce. The knowledge of crystal structures is important to understand their mode of action and to design genetically engineered enzymes with enhanced activity. The most difficult task and the limiting step in structural studies of cold-adapted enzymes is their crystallization,...
-
Ocena odporności powłok na bazie DLC na doraźne uszkodzenie w warunkach tarcia ślizgowego ze smarowaniem wodą i solą fizjologiczną = Evaluation of DLC based coatings resistance to instanteneous damage under sliding friction conditions with distilated water or saline lubrication
PublikacjaWykonano serię testów w celu wyznaczenia granicznych warunków wymuszenia, zdefiniowaego jako średnie naciski powierzchniowe oraz prędkość ślizgania, po przekroczeniu których następuje gwałtowne zniszczenie powłoki. Na podstawie wyników pomiarów opracowano aproksymowane charakterystyki granicznych wymuszeń w układzie p - v oraz pokrewnych dla badanych materiałów, smarów i zakresu parametrów wymuszenia.
-
CrN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A23/#B22
Dane BadawczeWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 12 min. The...
-
TiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B39/#A41
Dane BadawczeWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
TiN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A45/#A47
Dane BadawczeWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 20 min. The test...
-
SiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B34/#A33
Dane BadawczeWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
TiN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A45/#B45
Dane BadawczeWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 90 min. The test...
-
TiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A41/#B39
Dane BadawczeWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The...
-
CrN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B22/#A23
Dane BadawczeWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 6 min. The test...
-
SiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A33/#B34
Dane BadawczeWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
Information Hiding and Multimedia Security Workshop
Konferencje -
Ocena wybranych własności materiałowych polimerowej warstwy ślizgowej hydrodynamicznego łożyska wzdłużnego = An estimation of selected material properties of the hydrodynamic thrust bearing polymer lining
PublikacjaZaprezentowano metody pomiaru najważniejszych własności mechanicznych i cieplnych polimerowego pokrycia segmentowego łożyska wzdłużnego, do których zaliczyć należy moduł sprężystości wzdłużnej oraz współczynnik przewodności cieplnej materiału dodatkowym utrudnieniem planowanego zadania jest fakt, że próbka do badań dostępna będzie jedynie w formie wycinka z segmentu łożyskowego, z tego powodu nie jest możliwe zastosowanie ogólnie...
-
Aiding (opponent) flow of hybrid copper–aluminum oxide nanofluid towards an exponentially extending (lessening) sheet with thermal radiation and heat source (sink) impact
Publikacja -
Julita Wasilczuk dr hab.
OsobyUrodzona 5 kwietnia 1965 roku w Gdańsku. W latach 1987–1991 odbyła studia na Wydziale Ekonomiki Transportu Uniwersytetu Gdańskiego (obecnie Wydział Ekonomii). Od 1993 roku zatrudniona na nowo utworzonym Wydziale Zarządzania i Ekonomii, Politechniki Gdańskiej, na stanowisku asystenta. W 1997 roku uzyskała stopień doktora nauk ekonomicznych na WZiE, a w 2006 doktora habilitowanego nauk ekonomicznych w dyscyplinie nauki o zarządzaniu,...
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
TiN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B48/#A45
Dane BadawczeWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 12 min....
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B37/#A35
Dane BadawczeWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
CrN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B21/#A21
Dane BadawczeWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 25 min....
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B41/#A39
Dane BadawczeWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 9 min....
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A39/#B41
Dane BadawczeWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A35/#B37
Dane BadawczeWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
TiN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A45/#B48
Dane BadawczeWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 12 min....
-
CrN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A25/#B21
Dane BadawczeWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 9 min....
-
On the Bending of Multilayered Plates Considering Surface Viscoelasticity
PublikacjaWe discuss the bending resistance of multilayered plates taking into account surface/interfacial viscoelasticity. Within the linear surface viscoelasticity we introduce the surface/interfacial stresses linearly dependent on the history of surface strains. In order to underline the surface viscoelasticity contribution to the bending response we restrict ourselves to the elastic behaviour in the bulk. Using the correspondence principle...
-
Przemysław Krata dr hab. inż.
Osoby -
Rewitalizacyjny Living Lab jako metoda generowania i wdrażania innowacji na rzecz odnowy inteligentnego miasta na przykładzie dzielnicy Orunia w Gdańsku
PublikacjaW artykule poruszono kwestię możliwości wykorzystania w uspołecznieniu formuły pracy nad rewitalizacją modelu living lab tzw. żywego (żyjącego) laboratorium. Na tle przykładów praktyki zagranicznej (USA, Niemcy) dokonano odniesienia do doświadczeń polskich zebranych przez Autorkę w ramach współpracy ze społecznością gdańskiej dzielnicy Orunia - św. Wojciech. Zespół naukowy KUiPR WAPG Katedry Urbanistyki i Planowania Regionalnego...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Rotating rod and ball
PublikacjaWe consider a mechanical system consisting of an infinite rod (a straight line) and a ball (a massless point) on the plane. The rod rotates uniformly around one of its points. The ball is reflected elastically when colliding with the rod and moves freely between consecutive hits. A sliding motion along the rod is also allowed. We prove the existence and uniqueness of the motion with a given position and velocity at a certain time...
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Osiągnięcia leksykografów polskich na obczyźnie od wieku XVI do roku 1959 [The achievements of Polish lexicographers living abroad between the 16th century and the year 1959]
Publikacja -
[P4–544]: MEETINGDEM REPORTING ON THE IMPLEMENTATION, EFFECTIVENESS AND COST‐EFFECTIVENESS OF THE DUTCH MEETING CENTRES SUPPORTS PROGRAMME FOR PEOPLE LIVING WITH DEMENTIA AND FAMILY CARERS IN THREE EUROPEAN COUNTRIES
Publikacja -
International Conference on the Simulation and Synthesis of Living Systems
Konferencje -
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09A - full-run
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...