Filtry
wszystkich: 2779
-
Katalog
- Publikacje 1968 wyników po odfiltrowaniu
- Czasopisma 27 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Osoby 38 wyników po odfiltrowaniu
- Kursy Online 31 wyników po odfiltrowaniu
- Wydarzenia 3 wyników po odfiltrowaniu
- Oferty 1 wyników po odfiltrowaniu
- Dane Badawcze 710 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SOLAS CONVENTION
-
A method for preliminary estimation of the length of midship body block to be inserted during ship’s conversion
PublikacjaThe paper presents a method for preliminary estimation of the length of the midship body block, which inserted in the original hull, increases the deadweight of the ship in line with a required quantity. The method may be useful for establishing the scope of conversion to better adjust the ship for transportation tasks. The problem is formulated by using a mathematical model so selected that its solution, under set of assumptions,...
-
Thermochemical conversion strategies of biomass to biofuels, techno-economic and bibliometric analysis: A conceptual review
Publikacja -
Ultraviolet to near-infrared down-conversion in Bi3+–Yb3+ co-doped YAM phosphor
Publikacja -
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Conventional and advanced bending strength analysis of common and castellated, homogeneous and hybrid I-beams
PublikacjaAnaliza wytrzymałości na zginanie belek dwuteowych
-
The influence of the motor filtrers on harmonic current emmision in the pro-ective connection of drive systems.
PublikacjaThis paper contains detailed analysis of currents in protective wire in engine supplied from frequency converter without any external filters added. It was found that the peak value of current in protective conductor of engine was about 1500 mA at frequencies 5 Hz 50 Hz. In the continuation of research the dU/dt type motor filter and the sinusoidal filter were tested. It was found that the current in protective wire decreased...
-
Sustainable Management of Food Wastes Through Cavitation-Assisted Conversion into Value-Added Products
PublikacjaMore than 30% of worldwide food consumption is thrown out as food wastes causing serious environmental, economic, and social problems. Therefore, it is required to develop sustainable food waste management methods leading to an enhancement in social and economic benefits and mitigation of environmental impacts. Anaerobic digestion can be regarded as one of those effective methods that can be employed for the conversion of food...
-
Bio and slide bearings, their lubrication by non-Newtonian oils and applications in non-conventional systems
PublikacjaProject MTK-CT-2005-2008-517226Praca opisuje główne kierunki badawcze projektu europejskiego ToK, którego autor jest koordynatorem z ramienia Politechniki Gdańskiej.
-
Comparison of berry quality in highbush blueberry cultivars grown according to conventional and organic methods
Publikacja -
A Conception of Pairwise Comparisons Model for Selection of Appropriate Body Surface Area Calculation Formula
PublikacjaBody surface area (BSA) may be computed using a variety of formulas, but the computed BSA differs from real BSA values for particular subjects. This is presented in the paper by computing BSA values for selected subject and comparing them to the real BSA value obtained with the use of a 3D body scanner. The results show inequalities in the relevant BSA computing formulas. Hence, there is a need to determine a method that will allow...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublikacjaThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Engineering TADF, Mechanochromism, and Second Harmonic Up- conversion Properties in Regioisomeric Substitution Space
PublikacjaThis research article explores the distinct TADF efficiency of three donor-acceptor based regio-isomers: DPAOCN (ortho- isomer), DPAMCN (meta-isomer), and DPAPCN (para-isomer). DPAPCN exhibits maximum TADF efficiency in both solution and solid-state with an impressive reverse inter-system crossing (RISC) rate of ~ 106 s-1; the underlying cause being the minimum singlet-triplet splitting energy or ∆EST and maximum SOC (spin-orbit...
-
Influence of conductive carbon and MnCo2O4 on morphological and electrical properties of hydrogels for electrochemical energy conversion
PublikacjaIn this work, a strategy for one-stage synthesis of polymer composites based on PNIPAAm hydrogel was presented. Both conductive particles in the form of conductive carbon black (cCB) and MnCo2O4 (MCO) spinel particles were suspended in the three-dimensional structure of the hydrogel. The MCO particles in the resulting hydrogel composite acted as an electrocatalyst in the oxygen evolution reaction. Morphological studies confirmed...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublikacjaThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
Smart Decisional DNA Technology to Enhance Industry 4.0 Environment in Conjunction with Conventional Manufacturing
PublikacjaKnowledge-based support has become an indispensable part not only to the traditional manufacturing set-ups but also to the new fast-emerging Industry 4.0 scenario. In this regard, successful research has been performed and extensively reported to develop Decisional DNA based knowledge representation models of engineering object and engineering process called Virtual engineering object (VEO), Virtual engineering process (VEP) and...
-
Effect of Base-Connection Strength and Ductility on the Seismic Performance of Steel Moment-Resisting Frames
PublikacjaColumn-base connections in steel moment-resisting frames (SMFs) in seismic regions are commonly designed to develop the capacity of adjoining column with an intent to develop a plastic hinge in the column member, rather than in the connection (i.e., a strong-base design). Recent research has shown base connections to possess high ductility, indicating that this practice may be not only expensive but also unnecessary. This suggests...
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublikacjaDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
BODIPY‐Perylene Charge Transfer Compounds; Sensitizers for Triplet‐Triplet Annihilation Up‐conversion
PublikacjaBODIPY heterochromophores, asymmetrically substituted with perylene and/or iodine at the 2 and 6 positions were prepared and investigated as sensitizers for triplet-triplet annihilation up conversion (TTA-UC). Single-crystal X-ray crystallographic analyses show that the torsion angle between BODIPY and perylene units lie between 73.54 and 74.51, though they are not orthogonal. Both compounds show intense, charge transfer absorption...
-
Applied Solar Energy (English translation of Geliotekhnika)
Czasopisma -
Examination of the Effect of Selected Factors on the Photovoltaic Response of Dye-Sensitized Solar Cells
Publikacja -
Wind and Solar Power Plant End-of-Life Equipment: Prospects for Management in Ukraine
Publikacja -
Operational Properties Investigation of The Flat-Plate Solar Collector with Poliuretane Foam Insulation
Publikacja -
Modeling of TiO2-Based Electron-Selective Contacts for Crystalline Silicon Solar Cells
Publikacja -
Four-body recombination in organic bulk heterojunction solar cells: an alternative interpretation
PublikacjaWe demonstrate a new interpretation of the previously reported quadrimolecular recombination in organic bulk heterojunction solar cells. It is suggested that the recently described (Szmytkowski 2012 Phys. Status Solidi RRL 6 300) interaction between exciton and electron–hole Langevin bound pair formed across the donor–acceptor interface is a four-particle process. This is in opposition to the treatment of this effect as a three-particle...
-
Chemical, thermal and laser processes in recycling of photovoltaic silicon solar cells and modules
PublikacjaIn recent years, photovoltaic power generation systems have been gaining unprecedented attention as an environmentally beneficial method to solve the energy problem. From the economic point of view the pure silicon, which can be recapture from the used cells, is the most important material due to its cost and shortage. In the paper selected methods of used or damaged module and cells recycling and experimental results are presented....
-
Influence of excitons interaction with charge carriers on photovoltaic parameters in organic solar cells
PublikacjaWe report on theoretical analysis of excitons annihilation on charge carriers in organic solar cells. Numerical calculations based on transient one-dimensional drift-diffusion model have been carried out. An impact of three quantities (an annihilation rate constant, an exciton mobility and a recombination reduction factor) on current density and concentrations of charge carriers and excitons is investigated. Finally, we discuss...
-
Estimation of Solar Energy Influx to the Sea in the Light of Fast Satellite Technique Development
Publikacja -
Spray deposited carbon nanotubes counter electrodes for dye-sensitized solar cells
PublikacjaCarbon nanotubes due to their catalytic properties are a promising alternative to platinum counter electrodes (CE) for dye-sensitized solar cells (DSSC). In this study, counter electrodes were made from double-walled carbon nanotube (DWCNT) ink using the spray printing technique and afterwards thermally treated at temperatures ranging from 120 to 300 °C. Morphology and structure was studied using scanning electron microscopy and...
-
Spray-deposited carbon-nanotube counter-electrodes for dye-sensitized solar cells
PublikacjaCarbon nanotubes due to their catalytic properties are a promising alternative to platinum counter electrodes (CE) for dye-sensitized solar cells (DSSC). In this study, counter electrodes were made from double-walled carbon nanotube (DWCNT) ink using the spray printing technique and afterwards they were thermally treated at temperatures ranging from 120 to 300 °C. Morphology and structure was studied using scanning electron microscopy...
-
Advancing Solar Energy: Machine Learning Approaches for Predicting Photovoltaic Power Output
PublikacjaThis research is primarily concentrated on predicting the output of photovoitaic power, an essential field in the study of renewable energy. The paper comprehensively reviews various forecasting methodologies, transitioning from conventional physical and statistical methods to advanced machine learning (ML) techniques. A significant shift has been observed from traditional point forecasting to machine learning-based forecasting...
-
Temperature effect on the current-voltage characteristic fill factor for the silicon solar cells
PublikacjaW pracy przedstawiono badania wpływu temperatury pracy krzemowych ogniw fotowoltaicznych na wartość współczynnika wypełnienia charakterystyki prądowo- napięciowej (FF). Efekty dyfuzyjne w obszarze złącza oraz rekombinacja nośników ładunku ograniczają wartość współczynnika wypełnienia charakterystyki. Spadek tej wartości wynika głównie ze wzrostu wartości rezystancji szeregowej rs. Na rezystancję szeregową składają się: opór emitera...
-
Photovoltaic solar cells and modules as the source of electricity in the world and its future in Poland
PublikacjaJedną z metod ograniczenia emisji CO2 na świecie i w Polsce jest zastępowanie paliw kopalnych odnawialnymi źródłami energii. Systemy fotowoltaiczne, generujące energie elektryczną, są uważane za technologię wpisująca się w politykę zrównoważonego rozwoju dzięki znacznemu postępowi technologicznemu w zakresie ich wytwarzania i znacznej redukcji kosztów tych systemów.W artykule naświetlono postęp, jaki dokonał się w tej dziedzinie...
-
Photocatalytic water disinfection under the artificial solar light by fructose-modified TiO2
Publikacja -
Photocatalytic Water Disinfection under Solar Irradiation by d-Glucose-Modified Titania
Publikacja -
Research into GTA automatic soft soldering technology for solar energy collector components
Publikacja -
Exploring the interfacial effects at the ETL/perovskite boundary in the semitransparent perovskite solar cells
PublikacjaThe recent focus has been made on the perovskite solar cells (PSCs) with an inverted configuration, where substantial improvements have been already achieved. However, the p–i–n structure needs a buffer layer for most of the configurations to modify the work-function of a deposited electrode. Additionally and very importantly, such a layer can also serve as a protective film that improves a stability of solar cells. Here, we study...
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublikacjaLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublikacjaThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Activity and primary characterization of enzyme from Thermus ruber cells catalyzing conversion of maltose into trehalose
PublikacjaTermofilna bakteria Thermus ruber wytwarza syntazę trehalozy użyteczną do jednoetapowego przekształcania maltozy w trehalozę. Enzym ten wykazuje największą aktywność w temperaturze 65 C przy pH 6,5. Największą wydajność wytwarzania enzymu osiągano podczas hodowli drobnoustroju w temp. 55 stC w podłożu zawierającym 0,5% peptonu,0,1% ekstraktu drożdżowego oraz 0,% maltozy lub skrobi.
-
The conception of uncertainty analysis of reliability assessment of the MC type diesel engine lubricating oil system
PublikacjaOmówiono elementy składające się na niepewność oszacowania niezawodności instalacji oleju smarowego dla silników typu MC. Przedstawiono, posługując się przykładem obliczeniowym, koncepcję analizy niepewności oceny rozpatrywanej instalacji. Ponadto zaproponowano sposób interpretacji otrzymanego wyniku, obarczonego dużą niepewnością, przy użyciu liczb rozmytych.
-
Highly efficient conversion of waste plastic into thin carbon nanosheets for superior capacitive energy storage
Publikacja -
Old Problems - New Solutions: Conversion of Capitals as a Tool for Shaping the Competitive Position in the Economic Field
PublikacjaThe acts and operations any social actor effectuates in each of the logically distinguished spheres of reality are conditioned by many factors, among which a reliable analysis of the strengths and weaknesses of an agent should be considered of utmost importance. The concept of capitals presented in this article divides the quantity of resources available to all acting agents into four main categories (which allows for determining...
-
Logistical Aspects of Energy Conversion Efficiency in Marine Steam Power Plants in Off-Design Conditions
PublikacjaThe paper presents logistical aspects of energy conversion efficiency in off-design conditions. The main part of the article is based on results of thermodynamic calculation for large propulsion steam turbine under partial loads. Calculations are made on extended mathematical model of two proposed steam turbine thermodynamic cycles using Stodola’s cone law. The conclusion based on calculation re-sults contains importance of off-design...
-
COMPARISON OF THE CONVENTIONAL AND ALTERNATIVE GRANULAR MATERIALS FOR DUAL-MEDIA FILTRATION OF GROUNDWATER: PILOT PLANT TESTING
PublikacjaNowadays, occurrence of abnormal mineral or organic natural (geogenic) compounds concentrations, in ground and infiltration water, but also quite often in surface waters, is now a common problem encountered in Poland, Europe and many other countries throughout the world. The most concern is usually paid on the removal of iron (Fe) and manganese (Mn) as well as anthropogenic compounds (in particular referring to the organic compounds...
-
Conception of Interactive Information and Decision Support System for Urban and Industrial Air Quality Management: Extension
Publikacja -
Ag modified ZnO microsphere synthesis for efficient sonophotocatalytic degradation of organic pollutants and CO2 conversion
Publikacja -
Quantitative structure activity relationships for the conversion of nitrobenzimidazolones and nitrobenzimidazoles by DT-diaphorase: implications for the kinetic mechanism
Publikacja -
Scaling of signed residue numbers with mixed-radix conversion in FPGA with extended scaling factor selection
PublikacjaA scaling technique of signed residue numbers in FPGA is proposed. The technique is based on conversion of residue numbers to the Mixed-Radix System (MRS). The scaling factor is assumed to be a moduli product from the Residue Number System (RNS) base. Scaling is performed by scaling of MRS terms, the subsequent generation of residue representations of scaled terms, binary addition of these representations and generation of residues...