Filtry
wszystkich: 2963
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PAINT COATINGS
-
Fe-modified Mn2CuO4 spinel oxides: coatings based on abundant elements for solid oxide cell interconnects
PublikacjaThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublikacjaThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
In Vitro Studies on Nanoporous, Nanotubular and Nanosponge-Like Titania Coatings, with the Use of Adipose-Derived Stem Cells
PublikacjaIn vitro biological research on a group of amorphous titania coatings of different nanoarchitectures (nanoporous, nanotubular, and nanosponge-like) produced on the surface of Ti6Al4V alloy samples have been carried out, aimed at assessing their ability to interact with adipose-derived mesenchymal stem cells (ADSCs) and affect their activity. The attention has been drawn to the influence of surface coating architecture and its physicochemical...
-
Porous material-based sorbent coatings in Solid-phase microextraction technique: Recent trends and future perspectives
PublikacjaThe use of porous materials as sorbents in sample preparation techniques has gained recent scientific attention in the context of developing novel fibers for the Solid-phase microextraction (SPME) technique. SPME requires the appropriate selection of a robust sorbent for successful utilization under variable conditions. A deeper understanding of the nature of newly developed porous SPME coatings and the impact of their structures...
-
Electrochemically assisted deposition of hydroxyapatite on Ti6Al4V substrates covered by CVD diamond films — Coating characterization and first cell biological results
PublikacjaAlthough titaniumand its alloys are widely used as implant material for orthopedic and dental applications they show only limited corrosion stability and osseointegration in different cases. The aim of the presented research was to develop and characterize a novel surface modification system from a thin diamond base layer and a hydroxyapatite (HAp) top coating deposited on the alloy Ti6Al4V widely used for implants in contact with bone....
-
Behavioural genetics in Polish print news media between 2000-2014
Publikacja -
Fixed point theorems for weakly commuting and compatible multi-valued mappings.
PublikacjaW pracy podano twierdzenia o wspólnych punktach stałych czwórki odwzorowań: dwóch jednowartościowych T i S oraz dwóch wielowartościowych F i G, spełniających nieliniowy uogólniony warunek kontrakcyjny, przy pewnych założeniach dotyczących uogólnionej komutatywności T,S i F,G. W pracy zamieszczono przykłady ilustrujące udowodnione twierdzenia.
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublikacjaThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Investigation into Locking Point of Asphalt Mixtures Utilizing Superpave and Marshall Compactors
Publikacja -
Photodegradation of Benzo-[a]-pyrene on the Surface of the Photocatalytic Paints and Analysis of the Degradation Products
Publikacja -
Large elastic deformations of laminated cylindrical panels under point load
PublikacjaTematem pracy jest numeryczna analiza sprężysta cylindrycznych powłok kompozytowych w zakresie dużych obrotów. Analizując serię wielowarstwowych cylindrycznych powłok kompozytowych o brzegach utwierdzonych i obciążonych centralnie siła skupioną z pewnym zaskoczeniem zaobserwowano, że w przypadku określonych schematów uwarstwienia, nastąpić może wzrost wielkości obciążenia krytycznego mimo redukcji globalnej sztywności konstrukcji.
-
Influence of Aggregate Gradation on the Compactability of Asphalt Mixtures Utilizing Locking Point
Publikacja -
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublikacjaIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Reconstruction Methods for 3D Underwater Objects Using Point Cloud Data
PublikacjaExisting methods for visualizing underwater objects in three dimensions are usually based on displaying the imaged objects either as unorganised point sets or in the form of edges connecting the points in a trivial way. To allow the researcher to recognise more details and characteristic features of an investigated object, the visualization quality may be improved by transforming the unordered point clouds into higher order structures....
-
Fixed point indices of iterations of C^1 maps in R^3
PublikacjaW przypadku gładkiego odwzorowania w R^3 dowiedziona została hipoteza Chowa, Malleta-Pareta i Yorka dotycząca postaci ciągów indeksow iteracji oraz podano kompletny opis możliwych ciągów indeksow.
-
Influence of Asphalt Binder on the Compactability of Asphalt Mixtures Using Locking Point
PublikacjaCompaction is an important process for the asphalt mixture service life. A properly compacted mixture is crucial for long-lasting pavement. The objective of this study was to evaluate the influence of asphalt binders on the compactability of the asphalt mixtures by utilizing the concept of the locking point. To achieve this objective, two compaction methods (impact and gyration), different temperatures and asphalt content, and...
-
Reliability Analysis of Sea Cliff Slope Stability by Point Estimate Method
PublikacjaThe paper presents a reliability analysis of a sea cliff slope. The cliff, located in Jastrzębia Góra, is characterised by a complicated geological structure. Although currently stable, it is in fact close to the limit state. The objective of this paper is to present the point estimate method (PEM) of determining the mean value and standard deviation of the safety factor of the slope. Assuming its normal distribution, these statistical...
-
Reliability Analysis of Sea Cliff Slope Stability by Point Estimate Method
PublikacjaThe paper presents a reliability analysis of a sea cliff slope. The cliff, located in Jastrzębia Góra, is characterised by a complicated geological structure. Although currently stable, it is in fact close to the limit state. The objective of this paper is to present the point estimate method (PEM) of determining the mean value and standard deviation of the safety factor of the slope. Assuming its normal distribution, these statistical...
-
From a Point Cloud to a 3D Model - an Exercise for Users of AutoCAD and Revit
PublikacjaThe paper presents a proposal of the topic of an exercise for students of building faculties as part of classes on 3D modelling. The task consists in creating a three-dimensional model based on the measurement obtained with the Leica P30 laser scanner. Due to the maximum number of points in the cloud in the presented programs, the output files must be properly cleared and reduced. The point cloud was pre-processed in Cyclone software....
-
An Optimal Power Point Tracking Algorithm in a Solar PV Generation System
PublikacjaThe non-linearity in I-V characteristics of a PV panel requires to be operated at knee point to extract maximum power. In order to operate the panel at optimal point, maximum power point tracking (MPPT) algorithm is employed in the control structure. The main objective of MPP tracking is to keep the operation at knee point of I-V characteristics under varying condition of temperature and solar insolation. Under non uniform solar...
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublikacjaW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
High-temperature oxidation of the Crofer 22 H ferritic steel with Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings under thermal cycling conditions and its properties
PublikacjaThe aim of the presented study was to deposit protective-conducting Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings on the Crofer 22 H ferritic steel by means of electrophoresis and to evaluate their physicochemical properties after high-temperature oxidation under thermal cycling conditions. When the Crofer 22 H steel – whether uncoated or coated with the two spinels – was oxidized in 48-h cycles involving a temperature of...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Fixed Point Theory and Applications
Czasopisma -
Journal of Print and Media Technology Research
Czasopisma -
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublikacjaMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
Effects of Micro-Arc Oxidation Process Parameters on Characteristics of Calcium-Phosphate Containing Oxide Layers on the Selective Laser Melted Ti13Zr13Nb Alloy
PublikacjaTitania-based films on selective laser melted Ti13Zr13Nb have been formed by micro-arc oxidation (MAO) at different process parameters (voltage, current, processing time) in order to evaluate the impact of MAO process parameters in calcium and phosphate (Ca + P) containing electrolyte on surface characteristic, early-stage bioactivity, nanomechanical properties, and adhesion between the oxide coatings and substrate. The surface...
-
XPS measurements of the iron elements covered by chromium
Dane BadawczeAnticorrosive coatings are an important issue in modern materials engineering. One of the most commonly used, for that coating materials, is chrome. Three metal elements were measured, named as Turcja, WB Tech and Nomet. Names were given according to producer of elements. XPS measurements of the Cr 2p region give an ansver concering on surface chemical...
-
Treatment of chronic pain in oncology: cooperation between the oncologist and psychooncologist
Publikacja -
The effectiveness of therapeutic massage in neck pain – prospective, preliminary studies
Publikacja -
Structure and properties of the Ti+Ti(C,N) coatings obtained in the PVD process on sintered high speed steel
Publikacja -
The influence of plasma-sprayed coatings on surface properties and corrosion resistance of 316L stainless steel for possible implant application
Publikacja -
Influence of Ultrasound on the Characteristics of CaP Coatings Generated Via the Micro-arc Oxidation Process in Relation to Biomedical Engineering
PublikacjaOver the past decade, bone tissue engineering has been at the core of attention because of an increasing number of implant surgeries. The purpose of this study was to obtain coatings on titanium (Ti) implants with improved properties in terms of biomedical applications and to investigate the effect of ultrasound (US) on these properties during the micro-arc oxidation (MAO) process. The influence of various process parameters, such...
-
Quality Improvement of Wear-Resistant Coatings in Plasma Spraying Integrated with High-Energy Heating by High Frequency Currents
Publikacja -
Mechanical and Thermal Properties of W-Ta-B Coatings Deposited by High-Power Impulse Magnetron Sputtering (HiPIMS)
Publikacja -
Characterization and Wear Response of Magnetron Sputtered W–B and W–Ti–B Coatings on WC–Co Tools
Publikacja -
Superconducting properties of an NbN-SiO2 disordered system obtained by ammonolysis of NbN-SiO2 sol-gel derived coatings
PublikacjaW pracy przedstawiono wyniki badań właściwości nadprzewodzących warstw NbN-SiO2. Warstwy uzyskano poprzez azotowanie w temperaturze 1200C otrzymanych metodą zol-żel warstw Nb2O5-SiO2, o różnym stosunku molowym Nb2O5/SiO2. Badania rezystywne przeprowadzono w zakresie temperatur 5-280K. Przeprowadzono również badania absorpcji mikrofal (MMMA). Właściwości nadprzewodzące otrzymanych próbek silnie zależą od grubości warstw jak również...
-
Electrophoretically Deposited Chitosan/Eudragit E 100/AgNPs Composite Coatings on Titanium Substrate as a Silver Release System
PublikacjaDue to the possibility of bacterial infections occurring around peri-implant tissues, it is necessary to provide implant coatings that release antibacterial substances. The scientific goal of this paper was to produce by electrophoretic deposition (EPD) a smart, chitosan/Eudragit E 100/silver nanoparticles (chit/EE100/AgNPs) composite coating on the surface of titanium grade 2 using different deposition parameters, such as the...
-
Transparent nanocomposite coatings based on epoxy and layered double hydroxide: Nonisothermal cure kinetics and viscoelastic behavior assessments
PublikacjaLayered double hydroxide (LDH) has a particular place in clay family because of its flame retardant action. The nanoplatelet-like structure of LDH makes possible development of polymer composites with cationic or anionic nature structures in which macromolecules are positioned in between nanoplatelet galleries. In this work, neat epoxy and its transparent nanocomposite coatings with sodium dodecylbenzene sulfonate (SDBS)-modified...
-
Soiling Effect Mitigation Obtained by Applying Transparent Thin-Films on Solar Panels: Comparison of Different Types of Coatings
PublikacjaDust accumulation on the front cover of solar panels is closely linked to location and orientation of photovoltaic (PV) installation. Its build-up depends on the module tilt angle, frequency of precipitation, humidity, wind strength and velocity, as well as grain size. Additionally, soil composition is determined by solar farm surroundings such as local factories, agricultural crops, and traffic. Over time, molecules of atmospheric...
-
Recent advances on spinel-based protective coatings for solid oxide cell metallic interconnects produced by electrophoretic deposition
PublikacjaThe application of ceramic protective coatings to the metallic interconnects in solid oxide cells (SOCs) is a viable and effective method to limit interconnect degradation issues. This featured letter provides a critical overview of the main outcomes of current research on the use of the electrophoretic deposition (EPD) technique to produce protective coatings for SOC metallic interconnects, specifically focusing on different approaches...
-
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublikacjaPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Interlayer defect evolution in an organic coating system on steel under hydromechanical loading
Publikacja -
Advanced coating of interior of tanks for rising environmental safety - novel applications of polyurethanes
Publikacja -
Mitigating Stripping in Asphalt Mixtures: Pretreatment of Aggregate by Thermoplastic Polyethylene Powder Coating
Publikacja -
The Biocompatibility and Self-Healing Effect of a Biopolymer’s Coating on Zn Alloy for Biomedical Applications
Publikacja -
Effect of UV radiation and chitosan coating on the adsorption-photocatalytic activity of TiO2 particles
Publikacja -
Advanced coating of interior of tanks for rising environmental safety - numerical simulation of grounding
PublikacjaZwiększanie bezpieczeństwa środowiska naturalnego podczas transportu materiałów ropopochodnych stale stanowi ważny i aktualny problem badawczy. W pracy prezentowane są wyniki badań innowacyjnych powłok ochronnych zmniejszających ryzyko rozlewu olejowego podczas kolizji środków transportu - w szczególności statków. Prace badawcze prowadzone były w ramach programu Eureka E!3614 CORET.
-
Sliding Wear Performance of AlCrN Coating on TiB2/Ti Composites at High Temperatures
Publikacja