Publikacje
Filtry
wszystkich: 484
Katalog Publikacji
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Cost-Effective and Sufficiently Precise Integration Method Adapted to the FEM Calculations of Bone Tissue
PublikacjaThe technique of Young’s modulus variation in the finite element is not spread in biomechanics. Our future goal is to adapt this technique to bone tissue strength calculations. The aim of this paper is to present the necessary studies of the element’s integration method that takes into account changes in material properties. For research purposes, a virtual sample with the size and distribution of mechanical properties similar...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part II: Statistical Analysis and Interpretation of Tests
PublikacjaThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, and vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate (PET) bottles are increasingly used in this technology. In this paper, the main aim is to describe and interpret the results of statistical analysis of the influence of the temperature of...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublikacjaA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublikacjaDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Research on operational characteristics of tyres with run flat insert
PublikacjaThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
A literature survey of the influence of preform reheating and stretch blow moulding with hot mould process parameters on the properties of PET containers – part 2.
PublikacjaThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminised water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Wavelet Transform Analysis of Heart Rate to Assess Recovery Time for Long Distance Runners
PublikacjaThe diagnostics of the condition of athletes has become a field of special scientific interest and activity. The aim of this study was to verify the effect of a long (100 km) run on a group of runners, as well as to assess the recovery time that is required for them to return to the pre-run state. The heart rate (HR) data presented were collected the day before the extreme physical effort, on the same day as, but after, the physical...
-
Simple Computational Methods in Predicting Limit Load of High-Strength Cold-Formed Sections due to Local Buckling: A Case Study
PublikacjaCold-formed thin-walled sections are prone to local buckling caused by residual stresses, geometrical imperfections and inconsistency of material properties. We present a real case of buckling failure and conduct a numerical and experimental study aimed to identify methods capable of predicting such failures. It is important because designers of structures are getting more FEA-oriented and tend to avoid lengthy procedures of cold-formed...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublikacjaThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
THE DETERMINATION OF ABRASION RESISTANCE OF SELECTED BIOMATERIALS FOR THE FRICTION PAIRS IN THE HIP JOINT ENDOPROSTHESIS
PublikacjaThe key requirement for the modern endoprosthesis is high durability of the friction components, which results in long and trouble-free operation in the human body. The durability of currently used endoprosthesis is often limited by tribological wear processes of friction components (e.g. between the head and the acetabular component in a hip joint endoprosthesis) [8, 19, 23, 24]. In order to compare the tribological wear, tribological...
-
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part I: Research Methodology and Results
PublikacjaThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate bottles, commonly called PET, are increasingly used in this technology. In this paper, the main aim is to describe the statistical analysis methodology of the influence of the temperature of the...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublikacjaIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublikacjaThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublikacjaThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublikacjaPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublikacjaThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublikacjaIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulation and evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modeling and solution rely on finite element methods and cover the simulation of the structure’s properties along with the influence of the marine environment – sea currents, wave and wind loading,...
-
A literature survey of the influence of preform reheating and stretch blow molding with hot mold process parameters on the properties of PET containers. Part I.
PublikacjaThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminized water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublikacjaLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublikacjaPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublikacjaThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
Tire camber angle influence on tire-pavement noise
PublikacjaTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublikacjaRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublikacjaIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublikacjaJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Rehabilitation device supporting active and passive upper limb exercises
PublikacjaThis article presents a mechatronic solution for rehabilitation devices supporting active and passive exercises in persons with motor dysfunctions of the upper limbs in the area of the elbow and shoulder joints. A planar positioner integrated with original software and a control system, served as the basis for creating the present solution. Bellman’s programming method was applied to optimize the motion trajectory of the planar...
-
Heavy Duty Vehicle Fuel Consumption Modelling Based on Exploitation Data by Using Artificial Neural Networks
PublikacjaOne of the ways to improve the fuel economy of heavy duty trucks is to operate the combustion engine in its most efficient operating points. To do that, a mathematical model of the engine is required, which shows the relations between engine speed, torque and fuel consumption in transient states. In this paper, easy accessible exploitation data collected via CAN bus of the heavy duty truck were used to obtain a model of a diesel...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublikacjaDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublikacjaThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublikacjaAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
The non-invasive evaluation of heart function in patients with an acute myocardial infarction: The role of impedance cardiography
PublikacjaBackground: The purpose of this study was to analyze hemodynamic changes in patients treated with percutaneous coronary intervention (PCI) at an early stage of acute myocardial infarction (AMI) and at one-month follow-up. Methods: Patients with AMI (n = 27) who underwent PCI were analyzed using impedance cardiography (ICG). ICG data were collected continuously (beat by beat) during the whole PCI procedure and thereafter at every...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publikacjaequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Mechanical properties of the human stomach under uniaxial stress action
PublikacjaThe aim of this study was to estimate the range of mechanical properties of the human stomach in order to use the collected data in numerical modelling of surgical stapling during resections of the stomach. The biomedical tests were conducted in a self-developed tensile test machine. Twenty-two fresh human stomach specimens were used for the experimental study of its general strength. The specimens were obtained from morbidly obese...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...