Filters
total: 6705
filtered: 5901
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: NANOFLUIDS NUMERICAL METHODS
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublicationA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublicationThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublicationEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
Prediction of Weld Deformations by Numerical Methods - Review
PublicationThe welding process is the basic technique of joining in the shipbuilding industry. This method generates welding distortions that cause a lot of problems during the manufacturing process due to both the time and cost of straightening as well as their influence on later stages of production. Proper preparation of welding processes plays a growing role in the shipbuilding industry and the development of calculating tools is being...
-
Numerical methods for the assessment of bridge safety barriers
PublicationThe paper presents a numerical study of the bus crash test for bridge safety barriers. The analysis is conducted with the use of explicit code LS-DYNA. The problem of hourglass effect in shell elements is discussed. The simulations of bus impact against the barrier show that the analyzed barrier withstands the impact forces and restrains the bus trajectory to the bridge road.
-
Numerical-analytic methods for differential-algebraic systems
PublicationMetodę numeryczno-analityczną połączoną z metodą porównawczą zastosowano do układów równań różniczkowo-algebraicznych z linowymi warunkami brzegowymi otrzymując warunki dostateczne na istnienie rozwiązania. O prawych stronach zagadnienia zakładano warunek Lipschitza. Otrzymano oszacowania błędów. Problem z odchylonymi argumentami był również przedmiotem rozważań tej pracy.
-
Monotone and numerical analytic- methods for differential equations.
PublicationPraca dotyczy problemu różniczkowo-całkowego (typu Fredholma) z ogólnym warunkiem początkowo-brzegowo-całkowym. W pierwszej części pracy, stosując metodę iteracji monotonicznych, sformułowano warunki dostateczne które gwarantują, że dyskutowany problem ma rozwiązanie ekstremalne w zbiorze generowanym przez dolne i górne rozwiązania. Rozważania teoretyczne poparto przykładem i dyskusją. W drugiej części pracy zastosowano metodę...
-
Identification of ship’s hull mathematical model with numerical methods
PublicationThe modern maritime industry is moving toward the development of technology that will allow for full or partial autonomy of ship operation. This innovation places high demands on ship performance prediction techniques at the design stage. The researchwork presented in the article is related to the design stage of the ship and concerns methods for prognosis and evaluation of the specific operational condition of the ship, namely...
-
Numerical methods for systems of nonlinear differential functional equations
PublicationPraca dotyczy zagadnień początkowo brzegowych dla nieliniowych układów różniczkowo funkcyjnych. Rozważana jest aproksymacja rozwiązań rozważanego problemu różniczkowo funkcyjnego przez rozwiązania odpowiedniego problemu różnicowego. W pracy analizowana jest zbieżność prezentowanych metod. Dowód zbieżności opiera się na technice porównawczej z nieliniowym oszacowaniem typu Perron'a dla danych operatorów.
-
The use of numerical methods for the analysis of phase phenomena in multi element antennas.
PublicationW artykule zostały zaprezentowane wyniki analizy wpływu wzajemnej i własnej impedancji promieniowania na fazę sygnału odbieranego przez antenę wieloelementową. Obliczenia dokonano dla elektrycznego modelu zastępczego Mason`a przetwornika ultradźwiękowego.
-
A new open-source software developed for numerical simulations usingdiscrete modeling methods
PublicationThe purpose of this work is to present the development of an open-source software based on a discrete description of matter applied to study the behavior of geomaterials. This software uses Object Oriented Programming techniques, and its methodology design uses three different methods, which are the Discrete Element Method (DEM) [F. Donzé, S.A. Magnier, Formulation of a three-dimensional numerical model of brittle behavior, Geophys....
-
Use of numerical methods in the analysis of traction energy systems—an overview of the practical examples
PublicationA characteristic feature of trolleybus transport is the random nature of traffic caused by congestion. It predestinates statistical and numerical methods for the analysis of trolleybus energy system. There are presented 3 methods of trolleybus traction system analysis: simulation of supply system based on Monte Carlo method, analysis of energy recovery potential based on statistical data analysis and benchmark of trolleybus supply...
-
Comparison of AHP and Numerical Taxonomy Methods Based on Biogas Plant Location Analysis
PublicationThe paper presents a comparison of the multi-criteria Analytic Hierarchy Process (AHP) method and numerical taxonomy in biogas plant location selection. Biogas plants are sources that will significantly contribute to the implementation of the provisions of the energy and climate package for Poland by 2030. Increasing the share of energy produced from renewable sources, e.g. biogas plants, will increase the country’s energy security....
-
Numerical methods for nonlinear first-order partial differential equations with deviated variables
PublicationKlasyczne rozwiązania zagadnień początkowych dla nieliniowych równań cząstkowych z odchylonym argumentem aproksymowano za pomocą rozwiązań układów quasiliniowych równań różnicowych określonych na piramidzie Haara. Podano warunek dostateczny zbieżności metody. Stabilność schematu różnicowego wykazano metodą porównawczą. Przedstawiono metodę rozwiązywania nieliniowych równań różniczkowych cząstkowych z odchylonym argumentem bazującą...
-
Critical review of propeller performance scaling methods based on model experiments and numerical calculations
PublicationThe article presents the results of experimental and theoretical investigation of propeller scale effects. The objective of this investigation is to test the adequacy of the methods currently used and to develop possible improvement of the methods.New approaches to the problem and new procedures to account for the propeller scale effects are suggested. The description of the underlying experimental and theoretical research is included.
-
Comparision of two numerical methods for buried steel culverts made of corrugated shell sheets.
PublicationW pracy omawia się dwie metody analizy statycznej obudowy tuneli i przepustów dużej średnicy. Pierwsza z nich, metoda sprężyn polega na modelowaniu ośrodka gruntowego radialnymi sprężynami reprezentującymi odkształcalność gruntu. Drugie podejście oparte jest na zastosowaniu metody elementów skończonych i programu SOFISTIC. W układzie obudowa - grunt obudowę modeluje się zwykłymi ramowymi elementami sprężystymi a otaczający...
-
Impact of Energy Slope Averaging Methods on Numerical Solution of 1D Steady Gradually Varied Flow
PublicationIn this paper, energy slope averaging in the one-dimensional steady gradually varied flow model is considered. For this purpose, different methods of averaging the energy slope between cross-sections are used. The most popular are arithmetic, geometric, harmonic and hydraulic means. However, from the formal viewpoint, the application of different averaging formulas results in different numerical integration formulas. This study...
-
Numerical Solution of the Two-Dimensional Richards Equation Using Alternate Splitting Methods for Dimensional Decomposition
PublicationResearch on seepage flow in the vadose zone has largely been driven by engineering and environmental problems affecting many fields of geotechnics, hydrology, and agricultural science. Mathematical modeling of the subsurface flow under unsaturated conditions is an essential part of water resource management and planning. In order to determine such subsurface flow, the two-dimensional (2D) Richards equation can be used. However,...
-
Energy conversion in systems-contained laser irradiated metallic nanoparticles - comparison of results from analytical solutions and numerical methods
PublicationThis work introduces the theoretical method of metallic nanoparticles’ (NPs’) heat and mass transfer where the particles are coated on a surface (base), together with considering the case wherein nanoparticles move freely in a pipe. In order to simulate the heat transfer, energy and radiative transfer equations are adjusted to the considered issue. NPs’ properties are determined following the nanofluidic theories, whereas absorption...
-
Effect of grain crushing on shear localization in granular bodies during plane strain compression. Int. J. Numerical and Analytical Methods in Geomechanics
PublicationArtykuł omawia wpływ miażdżenia ziaren na lokalizacje odkształceń stycznych w materiałach granulowanych podczas ściskania dwuosiowego. Obliczenia MES wykonano przy zastosowaniu mikropolarnego prawa hipoplastycznego uwzględniającego zmianę średniej średnicy ziarna pod wpływem ciśnienia i ścinania. Obliczenia pokazały wpływ miażdżenia ziaren na szerokość lokalizacji.
-
Numerical aspects of improvement of the unsteady pipe flow equations
PublicationW pracy dokonano analizy zaproponowanych w ostatnich latach metod opisu oporów ruchu w przepływie nieustalonym w przewodach pod ciśnieniem. Wykazano,że modyfikacja współczynnika oporów liniowych nie może zapewnić pozytywnych efektów oraz ,że poprawa wyników wykazywana przez autorów modyfikacji wynika z błędu dyfuzji numerycznej generowanej przez metodę rozwiązania.
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublicationThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
An isogeometric finite element formulation for boundary and shell viscoelasticity based on a multiplicative surface deformation split
PublicationThis work presents a numerical formulation to model isotropic viscoelastic material behavior for membranes and thin shells. The surface and the shell theory are formulated within a curvilinear coordinate system,which allows the representation of general surfaces and deformations. The kinematics follow from Kirchhoff–Love theory and the discretization makes use of isogeometric shape functions. A multiplicative split of the surface...
-
Large eddy simulations of wall-bounded flows using a simplified immersed boundary method and high-order compact schemes
Publication -
Four-node semi-EAS element in six-field nonlineartheory of shells
PublicationW pracy sformułowano 4-węzłowy powłokowy element skończony dla konstrukcji powłokowych. Element opracowano w ramach nieliniowej 6-parametrowej teorii powłok z niesymetrycznymi miarami odkształceń membranowych. Kinematyka powłoki jest opisana przez dwa pola: translacji i obrotów, przy czym wszystkie trzy parametry obrotu traktowane są jako niezależne. W wyniku tego sformułowany element nadaje się do analizy struktur powłokowych...
-
Analysis of the incompressibility constraint in the smoothed particle hydrodynamics method
Publication -
Generation of large finite-element matrices on multiple graphics processors
PublicationThis paper presents techniques for generating very large finite-element matrices on a multicore workstation equipped with several graphics processing units (GPUs). To overcome the low memory size limitation of the GPUs, and at the same time to accelerate the generation process, we propose to generate the large sparse linear systems arising in finite-element analysis in an iterative manner on several GPUs and to use the graphics...
-
A general isogeometric finite element formulation for rotation‐free shells with in‐plane bending of embedded fibers
PublicationThis article presents a general, nonlinear isogeometric finite element formulation for rotation-free shells with embedded fibers that captures anisotropy in stretching, shearing, twisting, and bending - both in-plane and out-of-plane. These capabilities allow for the simulation of large sheets of heterogeneous and fibrous materials either with or without matrix, such as textiles, composites, and pantographic structures. The work...
-
A new finite element with variable Young's modulus
PublicationThe Finite Element Method (FEM) is a numerical technique that is well-established in the field of engineering. However, in biological sciences, it is justtaking its first steps. Bone tissue is an example of biological material which isexposed to high loads in its natural environment. Practically every movementof the body results in changing stress levels in the bone. Nature copes with thisvery well but when human intervention is...
-
Modelling hydraulic and capillary-driven two-phase fluid flow in unsaturated concretes at the meso-scale with a unique coupled DEM-CFD technique
PublicationThe goal of the research was to demonstrate the impact of thin porous interfacial transition zones (ITZs) between aggregates and cement matrix on fluid flow in unsaturated concrete caused by hydraulic/capillary pressure. To demonstrate this impact, a novel coupled approach to simulate the two-phase (water and moist air) flow of hydraulically and capillary-driven fluid in unsaturated concrete was developed. By merging the discrete...
-
Neohypoplasticity Revisited
Publication -
Non-coaxiality and stress-dilatancy rule in granular materials: FE-investigation within micro-polar hypoplasticity
PublicationW artykule przedstawiono wyniki numerycznej analizy nieosiowości i zasady naprężenie-dylatancja w materiałach granulowanych podczas ściskania dwuosiowego. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego modelu hipoplastycznego.
-
Deterministic and statistical size effect during shearing of granular layer within a micro-polar hypoplasticity
PublicationArtykuł omawia deterministyczny i statystyczny efekt skali w materiałach granulowanych podczas ścinania cienkiej warstwy piasku między dwoma bardzo szorstkimi ścianami. Obliczenia wykonano metodą elementów skończonych na bazie mikropolarnego prawa hipoplastycznego. Przyjęto różne metody redukujące ilość realizacji pól losowych dla początkowego wskaźnika porowatości..
-
Modeling of bearing capacity of footings on sand within stochastic micro-polar hypoplasticity.
PublicationAnalizowano numerycznie efekt wstępnego rozkładu wskaźnika porowatości na wytrzymałość i strefy ścinania w problemach fundamentów na piasku w skali modelowej. Obliczenia wykonano przy zastosowaniu stochastycznej metody elementów skończonych i mikropolarnego modelu hipoplastycznego. Wskaźnik porowatości miał formę skorelowanych pól stochastycznych. Dodatkowo obliczono efekt skali dla 3 różnych szerokości fundamentów.
-
Comparison of continuous and discontinuous constitutive models to simulate concrete behaviour under mixed mode failure conditions
PublicationW artykule porównano modele MES ciągłe i nieciągłe do symulacji zachowania betonu w warunkach mieszanego zniszczenia. W ramach modeli ciągłych zastosowano modele sprężysto-plastyczne oraz modele z redukcją sztywności sprężystej i nielokalnym osłabieniem. W ramach modeli nieciągłych zastosowano XFEM. Przedmiotem obliczeń były strefy lokalizacji i rysy w warunkach mieszanego zniszczenia wg testu doświadczalnego Nooru-Mohameda.
-
Discrete modeling of micro-structure evolution during concrete fracture using DEM
PublicationW artykule pokazano wyniki dyskretne DEM dla betonu poddanego ściskaniu i rozciąganiu jednoosiowemu. Wyniki siła-przemieszczenie i zarysowania porównano z doświadczeniami. Szczególną uwagę zwrócono na zjawiska mikrostrukturalne podczas zarysowania na poziomie kruszywa.
-
Discrete simulations of a triaxial compression test for sand by DEM.
PublicationArtykuł przedstawia wyniki symulacji dyskretnych dla ściskania trójosiowego stosując metodę elementów dyskretnych DEM. Symulacje wykonano dla piasku. Zastosowano kuli z momentami kontaktu do symulacji kształtu ziaren. Przeprowadzono analizy dla różnych zmiennych parametrów: średnica piasku, krzywa uziarnienia, kształt ziaren, wymiary próbki i warunki brzegowe.
-
Effect of gas content in macropores on hydraulic fracturing in rocks using a fully coupled DEM/CFD approach
PublicationW pracy skupiono się na wpływie zawartości gazu w makroporach skał na proces szczelinowania hydraulicznego. Proces został zasymulowany przez połączenie metody elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w ramach dwuwymiarowych (2D) warunków izotermicznych. Mechaniczne zachowanie skały zostało zasymulowane za pomocą DEM, a CFD została wykorzystana do opisu zachowanie przepływu laminarnego, dwufazowego płynu...
-
Numerical investigation of multiphase blood flow coupled with lumped parameter model of outflow
PublicationPurpose The purpose of this paper is the application of the computational fluid dynamics model simulating the blood flow within the aorta of an eight-year-old patient with Coarctation of Aorta. Design/methodology/approach The numerical model, based on commercial code ANSYS Fluent, was built using the multifluid Euler–Euler approach with the interaction between the phases described by the kinetic theory of granular flow (KTGF). Findings A...
-
A new model of fuel spray shape at early stage of injection in a marine Diesel engine
PublicationIn the cylinders of a marine diesel engine, self-ignition occurs in very shortly time after the fuel injection into the combustion chamber. Therefore, the paper present was to develop a model of diesel fuel spray for the early stage of fuel spray for in marine diesel engine. There were taken into consideration the main aspects technical such as nozzle diameter of marine engine injector and backpressure in combustion chamber. In...
-
Application of nanofluids in thermal technologies
PublicationNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Application of nanofluids in selected thermal technologies
PublicationSome peculiarities regarding convective heat transfer of nanofluids are presented. Particularly, results of the fundamental research concerning pool boiling and single phase convection of nanofluids as well as data obtained for selected heat exchangers operated with nanofluids are discussed.
-
Teoretyczno-doświadczalne modelowanie konwekcji wymuszonej nanocieczy
PublicationPrzedłożona rozprawa doktorska dotyczy badań eksperymentalnych oraz numerycznych konwekcji wymuszonej nanocieczy. Badane nanociecze wytworzone były z cieczy bazowych takich jak woda demineralizowana i mieszaniny wody z glikolem etylenowym w trzech proporcjach objętościowych 90:10, 80:20 i 60:40. Jako nanocząstki użyto Al2O3, a wytworzone nanociecze miały koncentracje masowe 0,1%, 1% i 5%. Wyznaczono eksperymentalnie dynamiczny...
-
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublicationThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublicationA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...