Search
Filters
total: 177
filtered: 156
Chosen catalog filters
Search results for: TEST STAND
-
Test Stand for Metamaterials Dynamic Properties Examination
Publication -
Test Stand for Multi-option Stretching of Soft Tissues
PublicationThe paper presents the genesis of the design and possibilities of the test stand for stretching soft tissues as well as examples of tests carried out on this device.
-
Test Stand for Multi-option Stretching of Soft Tissues
PublicationThe paper presents the genesis of the design and possibilities of the test stand for stretching soft tissues as well as examples of tests carried out on this device.
-
The automation of test stand for engine cooling system testing
PublicationW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublicationThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...
-
The Control System Based on FPGA Technology For Fatigue Test Stand MZGS-100 PL
Publication -
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublicationThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublicationThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
LABORATORY STAND FOR INVESTIGATIONS OF THE QUICK - CHANGING TEMPERATURE OF GAS FLOWING IN THE PISTON COMPRESSOR OUTLET CHANNEL
PublicationThis paper presents a laboratory stand, created as a part of work on the doctor dissertation, intended for investigation of heat and flow processes taking place in the Espholin H3S piston compressor outlet channel. The test stand elements and their configuration within the stand are described. Discussed are also problems connected with the quick-changing measurement technique, solutions which have been proposed so far in that technology...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublicationIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Fault detection in electronic circuits using test buses
PublicationA survey of test buses designed for diagnostics of digital and analog electronic circuits is presented: the IEEE 1149.1 bus for digital circuits, the IEEE 1149.4 bus for mixed-signal and the IEEE 1149.6 bus for AC coupled complex digital circuits. Each bus is presented with its structure, solution of key elements, particularly boundary registers and a set of test instructions. Diagnosis with the use of the described buses is...
-
Report no WOiO/II/67/2015 - Expertise about load capacity of twistlock foundation and sliding foundation
PublicationCustomer delivered to Laboratory 17 elements - twist lock foundations and sliding lock foundations (ship equipment for container lashing). Elements were selected from production series. Each element was loaded for braking load. After test visual inspection had been performed. The expertise contains: description of tested elements, test assumptions, test stand, results and conclusions
-
Measurement Stand and Methodology for Research of the Off-Body and Body-to-Body Radio Channels in WBANs with Different Diversity Schemes
PublicationThe concept of an experimental test bed for system loss and channel impulse response measurements for off-body and body-to-body radio channels in wireless body area networks (WBANs) is fully described. The possible measurement scenarios that may occur in investigation of off-body and body-to-body channels are classified and described in detail. Additionally, an evaluation is provided of the standard and expanded uncertainties of...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublicationThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
CAPABILITY OF IDENTIFYING AND PREDICTING THE TECHNICAL CONDITION OF PLATE HEAT EXCHANGERS IN OPERATION
PublicationThe paper presents a test stand for plate heat exchangers, allowing to identify the technical condition and to predict durability of the heat exchangers used aboard the sea-going ships: ”Oceanograf”, ”Władysław Orkan”and a passenger-car ferry, under the condition that they are of the same type and manufactured by the same company. In the first part three different installations with plate heat exchangers in the engine rooms...
-
Simple design criteria and efficiency of hydrodynamic vortex separators
PublicationVortex separators are locally applied for waste water treatment in different systems - from storm waste water sewerage to water treatment in fish ponds. However, the methods for separator design presented in the literature are questionable. The paper presents two simple and functional criteria that were employed to construct a laboratory test stand. The test results gave positive feed back on the efficiency of vortex separators.
-
Experimental Investigation of the Performance of an Innovative Implantable Left Ventricular Assist Device—Proof of Concept
PublicationThis paper presents the results of experimental performance of an innovative left ventricular assist device working on a specially designed test stand. The introduced invention is mainly applied for supporting the heart in patients with end-stage heart failure accompanied by mitral valve regurgitation and pulmonary hypertension. Moreover, the developed device has the form of a flexible balloon forming an intracardiac inert gas-filled...
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublicationThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Application of the F-statistic of the Fisher-Snedecor distribution to analyze the significance of the effect of changes in the compression ratio of a diesel engine on the value of the specific enthalpy of the exhaust gas flow
PublicationThe paper discusses the impact of changes in the compression ratio on the operating parameters of a diesel engine, e.g. on the temperature of exhaust gases. It presents the construction of the laboratory test stand, on which experimental measurements were realized. It is characterized how the actual changes of the compression ratio were introduced to the existing engine. The program of experimental investigations taking into account...
-
Environmental aspects of coastal earth structures made of soil-ash composites
PublicationThis paper presents an innovative technology of building the coastal dams with the use of soil-ash composites. A natural- scale test stand and results of the performed environmental tests are presented ; they have been compared with standards for purity of soils and waters. Also, an analysis of the obtained results and discussion of trends and anomalies in the observations, are given.
-
PROBLEMS OF EXPERIMENTAL DETERMINATION OF COEFFICIENTS OF THE WEAR OF SHIP PIPING SYSTEMS
PublicationThe article presents series of considerations relating to experimental evaluation of the reliability of ship piping systems. The aim of this study is to attempt to answer the following questions: What should be the tested element? How to choose the diameter of the tested item? What should be the result of measurements and calculations? How to measure? How to choose the duration of the test? How to choose the sample size and elaborate...
-
Novel condition monitoring of induction motor bearings via motor current signature analysis
PublicationThe paper authors are researching the assessment of bearing conditions in induction motors. The methods developed by the authors are based on measurements and analysis of the motor supply current, which is particularly attractive in the absence of access to the engine. The article provides an overview of selected methods of induction motor bearings diagnostic based on Motor Current Signature Analysis (MCSA). However, there is no...
-
Stanowisko do diagnostyki i regulacji wyzwalaczy przekaźników w obwodach lokomotyw elektrycznych
PublicationFast circuit breaker and protective relays play an important role of protecting locomotive’s electrical circuits from damage caused by short circuit or overload. Undisturbed operation and proper circuit protection depends on the technical condition and fine calibration of the over-current trips. Therefore the relays should be subject to periodic inspection and adjustment due to locomotive maintenance schedule. A test stand for...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublicationThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Analiza i ocena poprawności działania węzła tarcia w aspekcie II zasady termodynamiki
PublicationW artykule przedstawiono autorską metodę sprawdzania poprawności działania węzła tarcia traktowanego jako układ tribologiczny w aspekcie II zasady termo-dynamiki na podstawie analizy i oceny wyników badań laboratoryjnych wykonanych na stanowisku badawczym. Jako stanowisko wykorzystany został zmodyfikowany węzeł tarcia aparatu czterokulowego T-02. Zaprezentowano algorytm, według którego zostały wykonane badania empiryczne. Wykazano,...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublicationThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
A novel concept of H2/O2 steam generator
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublicationThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
Rotor Blade Geometry Optimisation in Kaplan Turbine
PublicationThe paper presents the description of method and results of rotor blade shape optimisation. The rotor blading constitutes a part ofturbine flow path. Optimisation consists in selection of the shape that minimises ratio of polytrophic loss. Shape of the blade isdefined by the mean camber line and thickness of the airfoil. Thickness is distributed around the camber line based on the ratio ofdistribution. Global optimisation was done...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Metodologia badania zaworów hamulcowych
PublicationArtykuł opisuje metodologię statycznego i dynamicznego badania zaworów hamulcowych. Stanowisko badawcze zaprojektowano i zbudowano na Politechnice Gdańskiej jako część projektu badawczo-rozwojowego pt.: „Zaprojektowanie i zbadanie innowacyjnych podsystemów ładowarek kołowych firmy Hydro-Metal”, dofinansowanego przez PARP w ramach programu „Bon na innowacje”. Ponadto przedstawiono szczegóły konstrukcyjne i funkcje najczęściej spotykanych zaworów...
-
Monitoring of current collectors on the railway line
PublicationProper cooperation the current collectors and the overhead line is a pre-requisite for reliable and safe operation of railway transport. Instances of maladjustment and, in some cases, damage to the current collectors, occur between periodic inspections of the rolling stock. In order to detect such anomalies quickly, the test stand was developed, with the aim of monitoring the technical state of the current collectors under operating...
-
Demonstrator testera wbudowanego BIST dla układów w pełni różnicowych
PublicationPrzedstawiono demonstrator testera wbudowanego, przeznaczony do pracy na stanowisku dydaktycznym w laboratorium z przedmiotu Zaawansowane Metody Pomiarowe i Diagnostyczne. Na stanowisku studenci zapoznają się z technologią BIST (ang. Built-In Self-Test), która jest przykładem wdrożenia strategii projektowania dla testowania.
-
A Comparison of Simplified Two-dimensional Flow Models Exemplified by Water Flow in a Cavern
PublicationThe paper shows the results of a comparison of simplified models describing a two-dimensional water flow in the example of a water flow through a straight channel sector with a cavern. The following models were tested: the two-dimensional potential flow model, the Stokes model and the Navier-Stokes model. In order to solve the first two, the boundary element method was employed, whereas to solve the Navier-Stokes equations, the...
-
Examination method of the effect of the incidence angle of laser beam on distance measurement accuracy to surfaces with different colour and roughness
PublicationInterest in the influence of the incidence angle of a laser beam to distance measurements can be seen in many areas of science and technology: geodesy, glaciology, archaeology, machine automation, and others. This paper presents results of measurements of the effect of the incidence angle of a laser beam to distance measurements to the surfaces of different colour and roughness by Topcon's electro-optical total station with an...
-
Wpływ wybranych właściwości maszyny badawczej na wynik eksperymentu tribologicznego z tarciem ślizgowym
PublicationNiniejsza monografia stanowi podsumowanie przekrojowych badań związanych z wpływem właściwości stanowiska badawczego (tribometru) na przebieg i rejestrowane wyniki eksperymentu tribologicznego z tarciem ślizgowym ciał stałych smarowanych cieczą w warunkach tarcia bez efektów smarowania hydrodynamicznego. Autor przedstawia wyniki kompleksowych analiz właściwości dynamicznych stanowiska badawczego w kontekście efektów obserwowanych...
-
Nowa metoda diagnostyki stanu technicznego nakładek stykowych
PublicationThe current collection system, which consists of the overhead contact line and a current collector, is particularly important in electric rail vehicles, where their reliability is concerned. Faultless current collection is conditioned not only by suitable construction of these elements but also by their proper maintenance. Retaining permanent electrical contact is essential in DC systems, where current demand is relatively high. In...
-
Laboratory research on the influence of swelling clay on the quality of borehole cementing and evaluation of clay-cutting wellbore tool prototype
PublicationSwelling clay phenomenon is frequently observed during oil and gas drilling operations and has a significant impact on the quality of cementing procedure. Certain types of clayey minerals increase their volume in contact with water-based drilling fluids. After drilling is completed, borehole remains unsupported and filled with waterbased drilling fluids for several hours, before a casing string is inserted and secured with cement....
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Interaction Between Storm Water Conduit Flow and Overland Flow for Numerical Modelling of Urban Area Inundation
PublicationNowadays we can observe increasing frequency of inundations in cities. This makes accurate predicting of inundations more important than ever. Numerical modeling of this issue requires complex approach with simultaneous calculations of pipe flow and surface flow. In this paper, after a short review of known methods used for solving pipe and surface flow, we will try to answer the question if presented methods would be sufficiently...
-
Investigation of Liquid–Gas Flow in a Horizontal Pipeline Using Gamma-Ray Technique and Modified Cross-Correlation
PublicationThis article presents the application of the radioisotope absorption method in the study of two-phase water–air flow in a horizontal pipe. The measurement principle and the test stand are briefly described. The main part of the article presents the signal analysis methods applied to data obtained from scintillation detectors. Because these signals are mostly stochastic waveforms, they were analyzed statistically using the cross-correlation...
-
Reliability model of slide bearings with particular attention given to lubricating oil
PublicationThe paper presents the slide bearing with circulating lubrication as a system of series three-element structure, where lubricating oil is the weakest link. In accordance with the Pierce statement that ''strength of chain is the strength of its weakest link'', a bearing reliability model has been developed. It allows to use the lubricating oil to evaluate the probability of correct working of the whole slide bearing, i.e. the reliability....
-
AN ENERGY APPROACH TO THE FATIGUE LIFE OF SHIP PROPULSION SYSTEMS
PublicationThe conducted research investigations aimed to carry out an identification of the constructional materials fatigue state of the ship propulsions’ rotational mechanical units for diagnostic purposes. The fatigue cracks of the elements transmitting mechanical energy streams from the propulsion engines to the ship propellers or to the generators of the ship’s electric power station stand for a primary reason for the secondary, usually...