Filters
total: 620
filtered: 481
-
Catalog
Chosen catalog filters
Search results for: Impact test
-
Test limitations induced by fault-driven instability of analog circuits.
PublicationCelem pracy jest ocena ograniczeń testowania uszkodzeń parametrycznych wynikajacych z utraty stabilności przez testowany układ analogowy. Zastosowano metody zapożyczone z teorii sterowania: liniową transformacje frakcyjną i analizę metodą strukturalnych wartości szczególnych. Przykładowej analizie poddano filtr typu leapfrog. Do obliczeń wykorzystano środowisko Matlab/Simulink. Wyniki obliczeń wykazały dużą podatność testowanego...
-
Design of poroelastic wearing course with the use of direct shear test
PublicationPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Investigation method of large-volume tire with mobile test rig
PublicationThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublicationThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
Eurozone or National Inflation Projections: Which has Greater Impact on Consumer Expectations?
PublicationWe compare the dependence of consumer inflation expectations on European Central Bank (ECB) inflation projections with that on national central bank (NCB) projections in four economies: Austria, Belgium, Finland, and Germany. We aim to assess whether the information published by central banks affects consumers, and whether inflation projections published by NCBs are more relevant to consumers than those published for the entire...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublicationThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublicationThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
Flow cytometric approach to evaluate the impact of hydro-technical concrete compounds’ release to the freshwater microbiome
PublicationThe aim of this research was to test the potential of applying a flow cytometric procedure to evaluate the impact of concrete compounds’ release to the freshwater microbiome. Cells from the collected samples were stained with a fluorogenic redox indicator dye that measures the redox potential of microbial cells. This novel approach was combined with the assessment of microorganisms’ penetration into the internal structures of concrete...
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublicationThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
<title>FPGA-based cavity simulator for Tesla test facility</title>
Publication -
Comparison of single microjet cooling with water, ethanol and HFE7100 as test fluids
PublicationThe paper presents the investigation of a single microjet cooling forming an thin liquid film on the impingement surface of specially designed rig. The basis of microjet technology is to produce laminar jets, which when impinging the surface have a very high kinetic energy at the stagnation point. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm in width....
-
A Test-Bed Analysis of Simultaneous PMIPv6 Handover in 802.11 WLANs Environment
PublicationProviding mobility in access networks is a challenge that we have to deal with. Due to networks’ convergence and migration to all-IP networks, mobility management at the network layer is required. However, there is a need for cooperation mechanisms between the network layer and lower layers to support multimedia services and make handover more efficient. This paper presents experimental research on simultaneous handover performance...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Evaluation of Thermal Stresses in Asphalt Layers Incomparison with TSRST Test Results
Publication -
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublicationThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
Determination of the bearing capacity of pile foundations based on CPT test results
PublicationAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
The relationships between asphalt mix rutting resistance and MSCR test results
PublicationW publikacji przedstawiono badania wpływu rodzaju asfaltu na odporność i deformacje. Wykazano, że w przypadku betonów asfaltowych jest lepsza korelacja pomiędzy cechami asfaltów a odpornością na deformacje niż w przypadku mieszanek mineralno-asfaltowych o nieciągłym uziarnieniu.
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Load Test of Railway Viaduct Built Using Crosswise Launching Technology
Publication -
Low Power Baseband Processor for M2M Reconfigurable Radio Test Platform
PublicationSoftware Defined Radio (SDR) is becoming more andmore frequently used technique for wireless communication. Itfacilitates as fast prototyping and is a versatile method fordeveloping new communication systems. SDR can be realizedbased on high computational capacity platform, where powerconsumption is no a primary concern like i.e. DVB or BTStransmitters. Another trend are low power systems, whereavailable power in reduced and more...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublicationThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
On the influence of shell element properties on the response of car model in crash test
PublicationIt goes without saying that numerical simulations play important role in the modern engineering practice. Contemporary CAD environments combined with FEM solvers, along with computer power of modern processors, give the engineer fast and efficient tool. Ultimately, however it is the user alone who is responsible for the correctness of the results. As long as the FEM calculations remain in the sphere of academic exercise, the inevitable...
-
Comparison of a tribological model and real component test methods for lubricated contacts
Publication -
Influence of Silicon Additives on Tribological and Rheological Test Results for Vegetable Lubricants
Publication -
Gendered Self-Views Across 62 Countries: A Test of Competing Models
Publication -
Bacterial luminescence test screening of highly polluted areas in the Odra River
PublicationW pracy przedstawiono wyniki badania ekotoksyczności wód i osadów z dorzecza Odry w obrazie testu z zastosowaniem bakterii Vibrio Fischerii. Badania przesiewowe wskazują, że silnie zanieczyszczone są miejsca w okolicy Brzegu Dolnego, ujścia Nysy Kłodzkiej i Małej Panwi.
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
The role of low-energy electrons in the charging process of LISA test masses
PublicationThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Development and test of fex, a fingers extending exoskeleton for rehabilitation and regaining mobility
PublicationThis paper presents the design process of an exoskeleton for executing human fingers' extension movement for the rehabilitation procedures and as an active orthosis purposes, together with its first clinical usability tests of a robotic exoskeleton. Furthermore, the Fingers Extending eXoskeleton (FEX) is a serial, under-actuated mechanism capable of executing fingers' extension. FEX is based on the state-of-art FingerSpine serial...
-
A method of Functional Test interval selection with regards to Machinery and Economical aspects
PublicationThis paper discusses the problem of choosing the optimal frequency of functional test, including the reliability calculations and production efficiency, but also the effect of company risk management. The proof test as a part of the functional test interval is well described for the process industry. Unfortunately, this situation is not the case for the machinery safety functions with low demand mode. Afterwards, it is presented...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublicationThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
Neurochemical changes underlying cognitive impairment in olfactory bulbectomized rats and the impact of the mGlu5-positive allosteric modulator CDPPB
PublicationThe olfactory bulbectomized (OBX) rat model is a well-established model of depression in which antidepressant drugs reverse deficits in the passive avoidance test 14 days after administration. Recently, the olfactory bulbectomized rat model has been proposed to be a model of Alzheimer’s disease (AD), and the available data indicate similarities between the changes that typically occur in AD and those observed in OBX animals. In...
-
The Impact of Thermal Stresses on Volume Resistivity: Performance Comparison between TR-XLPE and XLPE Cables
PublicationMost failures in electric power cables are attributed to the development of water trees inside the insulating materials. Thus, the development and utilization of Tree Retardant Cross-Linked Polyethylene (TR-XLPE) based cables have recently been given great attention to overcome the treeing issues. TR-XLPE cables use low-density polyethylene compounds suppressing the formation of water trees while retaining excellent electrical,...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublicationThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
Assessment of the Bulgarian Wastewater Treatment Plants’ Impact on the Receiving Water Bodies
PublicationDeterioration of water quality is a major problem world widely according to many international non-governmental organizations (NGO). As one of the European Union (EU) countries, Bulgaria is also obliged by EU legislation to maintain best practices in assessing surface water quality and the efficiency of wastewater treatment processes. For these reasons studies were undertaken to utilize ecotoxicological (Microtox®, Phytotoxkit...
-
F05 Nine Hole Peg Test As A Measure Of Visuomotor Coordination In Huntington's Disease
Publication -
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio-Tribological Applications
PublicationZaprezentowano metodę badań ogólnej charakterystyki tribologicznej cienkich powłok ceramicznych z wykorzystaniem równoległych testów na wielu stanowiskach o różnej konfiguracji styku powierzchni trących i przy ruchu o różnym charakterze (jednokierunkowym i posuwisto zwrotnym). Przedstawiono wyniki porównania przy pomocy jednoczesnej analizy wyników testów z różnych stanowisk; w wyniku testów uzyskano ranking powłok ze wskazaniem...
-
<title>JTAG test system for RPC muon trigger in the CMS experiment</title>
Publication -
Corrosion resistance of sintered duplex stainless steels in the salt fog spray test
Publication -
Automotive Validation Functions for On-line Test Evaluation of Hybrid Real-time Systems
PublicationThe aim of this paper is to present the means of black-box on-line test evaluation for hybrid real-time systems. The described procedures can be used for the model-based testing process so as to improve its effectiveness. In particular, intelligent automotive validation functions are considered, which are divided into different types depending on the nature of the evaluated issue. All provided definitions are specified on the meta-model...
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublicationThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...
-
Validation of a virtual test environment for C2X communication under radio jamming conditions
PublicationIn this paper, we propose a novel car-2-x communication security testing methodology in the physical layer of wireless systems. The approach is dedicated to automated testing of autonomous vehicles and it is essential for such complex systems operation, especially with regard to safety and security issues. It is based on scenario-driven testing in virtual and real test environments created from collected or simulated data. The...
-
Accurate and continuous adhesive fracture energy determination using an instrumented wedge test
PublicationThe wedge test and the related double cantilever beam test are practical methods of assessing structural adhesive fracture energy. In the former, and to a lesser extent the latter, a recognised problem is the difficulty of following the length of the growing crack, required to calculate fracture energy with any accuracy. We present a novel method of measurement of crack length that has the advantages of being accurate and allowing...
-
Test równoważności metod pomiarowych stosowanych do oznaczania pyłu zawieszonego PM10
PublicationW pracy przedstawiono przyczyny wystepowania różnic wartości stężeń pyłu PM10 uzyskiwanych metodą referencyjną a metodami opartymi na pomiarze w trybie on-site. Przedyskutowano metodykę wyznaczania równania bądź współczynnika korekcyjnego dla ciągłych metod pomiarowych w oparciu o unijną dyrektywę. Przeprowadzono weryfikację tej metodyki korzystając z danych uzyskanych z testu terenowego. Wyznaczono równanie korekcyjne przy pomocy...
-
Determination of PCBs in river sediment samples—proficiency test for selected Polish laboratories
Publication -
Assessment of the physical fitness of road cyclists in the step and ramp protocols of the incremental test
Publication -
Evaluating the performance of inverted pavement structure using the accelerated pavement test (APT)
Publication