Search results for: mechanics
-
Effect of power frequency on the stress state of disc actuator
PublicationThe paper presents the concept of determinig the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics.
-
Experimental Verification of Storm Sewer Transient Flow Simulation
PublicationThe paper focuses mainly on laboratory investigations of transient and transcritical flow in a single pipe of a sewer system. The aim of this paper is to present a comparison between pressure values calculated by an improved McCormack scheme and those measured at the hydraulic laboratory of the Gdansk University of Technology, which were observed inside a pipe in an experiment for water flow with pressurization. The analysis proves...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublicationThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Model of pressure distribution in vortex flow controls
PublicationThe paper is devoted to the vortex valve. Existing devices are described by CFD-methods, or by means of simple empirical relations. A rational method of the considered object design is proposed, on the base of the input and dissipation energy balance., what gives a simple algebraic equation. Conformity between calcul;ated and measured parameters of the vortex valve allows for acceptation of the proposed concept.
-
A Comparison of Simplified Two-dimensional Flow Models Exemplified by Water Flow in a Cavern
PublicationThe paper shows the results of a comparison of simplified models describing a two-dimensional water flow in the example of a water flow through a straight channel sector with a cavern. The following models were tested: the two-dimensional potential flow model, the Stokes model and the Navier-Stokes model. In order to solve the first two, the boundary element method was employed, whereas to solve the Navier-Stokes equations, the...
-
Simplified probabilistic analysis of settlement of cyclically loaded soil stratum using point estimate method
PublicationThe paper deals with the probabilistic analysis of settlement of a non-cohesive soil layer subjected to cyclic loading. Originally, the settlement assessment is based on deterministic compaction model which requires integration of a set of differential equations. However, making use of the Bessel functions the settlement of the soil stratum can be calculated by means of simplified algorithm. The compaction model parameters were...
-
Whirling system of water exchangein breeding pools
PublicationTo secure the proper conditions of life for sea mammals existing in closed systems one has to maintain the character of the breeding basins (i.e. shape, dimensions, facing of walls and bottom, quality and motion of water) as natural as possible. An appropriate system of water exchange plays a very important role here. A full renewal of water is time-consuming, expensive and troublesome, so can be made only periodically, and should...
-
Buckling of thin-walled columns accounting for initial geometrical imperfections
PublicationThe paper is devoted to the effect of some geometrical imperfections on the critical buckling load of axially compressed thin-walled I-columns. The analytical formulas for the critical torsional and flexural buckling loads accounting for the initial curvature of the column axis or the twist angle respectively are derived. The classical assumptions of theory of thin-walled beams with non-deformable cross-sections are adopted. The...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublicationWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Galerkin formulations of isogeometric shell analysis: Alleviating locking with Greville quadratures and higher-order elements
PublicationWe propose new quadrature schemes that asymptotically require only four in-plane points for Reissner–Mindlin shell elements and nine in-plane points for Kirchhoff–Love shell elements in B-spline and NURBS-based isogeometric shell analysis, independent of the polynomial degree p of the elements. The quadrature points are Greville abscissae associated with pth-order B-spline basis functions whose continuities depend on the specific...
-
The protocol for using elastic wall model in modeling blood flow within human artery
PublicationMedical diagnostic tools will play a major role in the future for an effective patient treatment and reduction their mortality, related to the cardiovascular system diseases (CVDs). There is an urgent need for developing diagnostic procedure to be robust, reliable, accurate and efficient, in the framework of a paradigm shift. Application of numerical techniques is seen as a perspective tool for such purpose. Nevertheless, existing...
-
Numerical Analysis of Turbulent Flow over a Backward-facing Step in an Open Channel
PublicationComputational examinations of the flow field in an open channel having a single Backward--Facing Step (BFS) with a constant water depth of 1.5 m were performed. The effects of the expansion ratio, and the flow velocity along the reattachment length, were investigated by employing two different expansion ratios of 1.5 and 2, and eight various flow velocities of 0.5, 1, 2, 3, 4, 5, 7.5 and 10 m/sec in the Computational Fluid Dynamic...
-
Efficient and robust quadratures for isogeometric analysis: Reduced Gauss and Gauss–Greville rules
PublicationThis work proposes two efficient quadrature rules, reduced Gauss quadrature and Gauss–Greville quadrature, for isogeometric analysis. The rules are constructed to exactly integrate one-dimensional B-spline basis functions of degree p, and continuity class C^{p−k}, where k is the highest order of derivatives appearing in the Galerkin formulation of the problem under consideration. This is the same idea we utilized in Zou et al....
-
An isogeometric finite element formulation for geometrically exact Timoshenko beams with extensible directors
PublicationAn isogeometric finite element formulation for geometrically and materially nonlinear Timoshenko beams is presented, which incorporates in-plane deformation of the cross-section described by two extensible director vectors. Since those directors belong to the space R3, a configuration can be additively updated. The developed formulation allows direct application of nonlinear three-dimensional constitutive equations without zero...
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublicationThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
A selectively reduced degree basis for efficient mixed nonlinear isogeometric beam formulations with extensible directors
PublicationThe effect of higher order continuity in the solution field by using NURBS basis function in isogeometric analysis (IGA) is investigated for an efficient mixed finite element formulation for elastostatic beams. It is based on the Hu–Washizu variational principle considering geometrical and material nonlinearities. Here we present a reduced degree of basis functions for the additional fields of the stress resultants and strains...
-
Large rotations in first-order shear deformation FE analysis of laminated shells
PublicationAbstrakt: Teoria powłok o skończonych obrotach w ramach modelu ścinania pierwszego rzędu stanowi podstawę zaprezentowanego w pracy algorytmu MES statycznej, geometrycznie nieliniowej analizy konstrukcji warstwowych. Szczególną uwagę zwrócono na właściwy opis skończonych obrotów przy zastosowaniu kątów Eulera oraz procedurę uaktualniania parametrów obrotowych. Przedstawiono sformułowanie przyrostowe w stacjonarnym opisie Lagrange´a....
-
Soft soil overconsolidation and CPTU dissipation test
PublicationOkreślenie stanu naprężeń oraz historii naprężeń w słabym podłożu pod wałem przeciwpowodziowym na podstawie badań CPTU i DMT. Przeprowadzono badania dysypacji nadwyżki ciśnienia wody w porach w podłożu pod wałem oraz po stronie odpowietrznej i odwodnej. Kształt krzywej dysypacji zależy od prekonsolidacji gruntu słabego. Przedstawiono sposoby określania współczynnika konsolidacji oraz współczynnika filtracji w gruntach słabych w...
-
Application of potential theory in calculating wave-induced vertical forces on horizontal cylinders near a plane boundary
PublicationHydrodynamiczne obciażenia wywołane falowaniem morskim działajace na poziomo ułożoną przy dnie rurę, rozpatrywane są w ujęciu dyfrakcyjnym przy założeniu istnienia funkcji potencjału. Potencjał zdefiniowano jako superpozycję potencjału fali inicjującej oraz potencjału perturbacji spowodowanej istnieniem obiektu przy dnie. Wyniki rozwiązań teoretycznych porównano z wynikami doswiadczeń przeprowadzonych w Wielkim Kanale falowym w...
-
Numerical simulations of triaxial test with sand using DEM. Archives of Hydro-Engineering and Environmental
PublicationW artykule przedstawiono wyniki symulacji badania trójosiowego dlamateriałów granulowanych. Obliczenia wykonano przy zastosowaniu metodyDEM. Pokazano wpływ momentów kontaktowych na wytrzymałoć próbki. Zbadanowpływ parametrów mikroskopowych na zachowanie się materiału. Wynikiporównano z doswiadczeniami.
-
Size effects in problems of footings on sand within micro-polar hypoplasticity.
PublicationW artykule przedstawiono obliczenia efektów skali na nośność fundamentu na piasku. Obliczenia wykonano przy pomocy mikropolarnego prawa hipoplastycznego. W obliczeniach wykorzystano stochastyczne rozkłady początkowego wskaźnika porowatości według rozkładu Gaussa oraz różne wymiary fundamentu.
-
Effect of grain crushing on shear localization in granular bodies within micro-polar hypoplasticity
PublicationW artykule przedstawiono efekt miażdżenia ziaren na zachowanie się materiału granulowanego podczas ścinania nieskończenie długiej warstwy piasku. Obliczenia wykonano przy pomocy mikropolarnego prawa hipoplastycznego rozszerzonego o efekt miażdżenia ziaren w oparciu o teorię mechaniki zniszczenia. Zbadano wpływ wstępnego zagęszczenia i poziomu naprężeń na strefy lokalizacji.
-
Deformation measurements in granular bodies using a particle image velocimetry technique
PublicationW artykule przedstawiono wyniki pomiarów tensora odkształceń w materiałach granulowanych podczas przepływu silosowego i wyciągania ścianki z gruntu. Pomiary wykonano przy zastosowaniu techniki obrazu cyfrowego PIV wykorzystującego technikę korelacji.
-
2D lattice model for fracture in brittle materials
PublicationW artykule przedstawiono wyniki obliczeń propagacji rys w elementach betonowych przy zastosowaniu modelu dyskretnego opartego na ruszcie belkowym. Obliczenia wykonano dla różnych problemów brzegowych.
-
Stochastic FE-analysis of shear localization in 2D granular material within a micro-polar hypoplascity
PublicationW artykule przedstawiono wyniki numerycznej stochastycznej analizy wpływu rozkładu początkowego wskaźnika porowatości w materiałach granulowanych na powstawanie lokalizacji odkształceń. Obliczenia wykonano dla ścinania warstwy piasku stosując metodę elementów skończonych na bazie mikropolarnego prawa hipoplastycznego.
-
Experimental investigations of strain localization in concrete using Digital Image Correlation (DIC) technique
PublicationW artykule przedstawiono wyniki pomiarów tensora odkształceń w belkach betonowych podczas zginania. Pomiary stref pękania wykonano przy zastosowaniu techniki fotooptycznej DIC.
-
A non local hypoplastic constitutive law to describe shear localization in granular bodies.
PublicationPrzedstawiono wyniki numerycznej analizy formacji stref ścinania w materiale granulowanym podczas ściskania. Zachowanie suchego piasku podczas testów ściskania w płaskim stanie odkształcenia było analizowane z zastosowaniem metody elementów skończonych i nielokalnego hipoplastycznego prawa konstytutywnego. Podczas obliczeń numerycznych zwrócono szczególną uwagę na wpływ długości charakterystycznej na nośność i szerokość...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Toward a Method Evaluating Control Actions in STPA-Based Model of Ship-Ship Collision Avoidance Process
Publication -
A Study of the Roll Motion by Means of a Free Decay Test
Publication -
Modelling of heat and mass transfer through wooden buildings
PublicationThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Comparative analysis of switched reluctance motor control algorithms
PublicationПредмет исследования. Развитие микропроцессорной техники и силовой электроники позволило создавать недорогие и эффективные системы управления различными электромеханическими объектами, которые ранее широко не использовались из-за сложности управления. К таким устройствам можно отнести вентильно-индукторные электрические машины. Данные машины широко применяются в различных практических разработках, например, в тяговом электроприводе,...
-
Comparative analysis of switched reluctance motor control algorithms
PublicationПредмет исследования. Развитие микропроцессорной техники и силовой электроники позволило создавать недорогие и эффективные системы управления различными электромеханическими объектами, которые ранее широко не использовались из-за сложности управления. К таким устройствам можно отнести вентильно-индукторные электрические машины. Данные машины широко применяются в различных практических разработках, например, в тяговом электроприводе,...
-
Mechanisms positioned in a neighbourhood of their singular positions - velocity amplification in the electromagnetic damping. Part 2. Numerical Verification
PublicationPraca prezentuje zagadnienia występujące podczas elektromagnetycznego tłumienia drgań układów mechanicznych. Analizowano zachowania układu ciągłego i jego drgania. Aby przyśpieszyć tłumienie, wprowadzono specjalny dwuramienny mechanizm umieszczony pomiędzy elementem drgającym i elementem tłumiącym drgania. Mechanizm ustawiony jest w pobliżu swojego ustawienia osobliwego. Aby określić potencjalny kierunek zmian prowadzący do poprawić...
-
Mechanisms positioned in a neighbourhood of their singular positions - velocity amplification in the electromagnetic damping. Part 1 - Background of the mechanical structure modeling
PublicationW pracy przedstawiono metodę modelowania dynamiki drgającego hybrydowego układu mechanicznego złożonego z odkształcalnego podukładu ciągłego oraz z połączonego z nim mechanizmu. U układzie pojawiają się drgania części odkształcalnej. By je wytłumić, ich energia zamieniana jest w energię elektryczną (za pomocą prądnicy prądu stałego) i rozpraszana na oporności obecnej w układzie elektrycznym. Aby przyśpieszyć tłumienie, wprowadzony...
-
Victor Eremeev prof. dr hab.
People -
Mohammad Malikan dr inż.
PeopleMohammad Malikan studied Ph.D. at the Department of Mechanics of Materials and Structures at the Gdańsk University of Technology. He was the first person who graduated in the new form of the doctoral education system of Poland (Doctoral School). He has worked as a mechanical engineer and designer for several years in CAD/CAE fields in various industries, such as feed production lines, machinery, elevator, oil, etc. His main research...
-
Łukasz Skarżyński dr hab. inż.
People -
Karol Grębowski dr inż.
PeopleKarol Grębowski (M.Sc.) works as an assistant at the Department of Technical Fundamentals of Architecture Design of the Faculty of Architecture at Gdansk University of Technology. His scientific research deals with dynamic phenomena occurring during the vibration of structures, bridges, and studies the design methodology of the elements forming passive protection system of the vehicles degraded by struck or explosion in the context...
-
Krzysztof Wilde prof. dr hab. inż.
PeopleKrzysztof Wilde (born January 11th, 1966 in Gdańsk) – expert in bridge structures, structural mechanics and diagnostics of civil structures. He conducted research on vibration reduction systems for bridges exposed to dynamic loads from winds and earthquakes. At present he is interested in the field of nondestructive testing of materials and structural health monitoring systems. Hi is author or coauthor of over 200 publications...
-
Angelika Duszyńska dr inż.
PeopleAbsolwentka kierunku Budownictwo Wodne Wydziału Hydrotechniki Politechniki Gdańskiej, doktor nauk technicznych w dziedzinie Geotechnika, nauczyciel akademicki (od 2020 roku pracuje na stanowisku profesora uczelni na wydziale Inżynierii Lądowej i Środowiska PG). Prowadzi zajęcia z przedmiotów: Geoinżynieria, Geotechnika, Budowle Ziemne i Wzmacnianie podłoża, Geosyntetyki w Budownictwie, Budowle Hydrotechniczne. Od ponad 20 lat...
-
Rafał Ossowski dr inż.
PeopleRafał Ossowski (born June 8th, 1973 in Chojnice) – expert in soil mechanics and geotechnics, mainly in field of numerical modeling and research on anthropogenic soils. Author and coauthor of publications on numerical modeling in soil mechanics, field soil investigation and application of anthropogenic soils in context of so-called "green geotechnics". In 1992–1997 he studied at the Faculty of Hydrotechnics GUT (renamed: Faculty...
-
Wiktoria Wojnicz dr hab. inż.
PeopleDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) List of papers (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E., Analysis of...
-
Agnieszka Tomaszewska dr hab. inż.
People -
Izabela Lubowiecka dr hab. inż.
People -
Mateusz Kopec Dr hab. inż.
PeopleHead of the Materials and Structural Testing Laboratory in Institute of Fundamental Technological Research PAS and Academic visitor in Imperial College London. Lecturer and Master/PhD students supervisor in Doctoral School of IPPT PAN and TIB PAN, and Imperial College London. Member of Polish Materials Science Society, Member of the Board of Polish Society of Theoretical and Applied Mechanics, and Council Member of the European...
-
Magdalena Palacz dr hab. inż.
People -
Ireneusz Kreja dr hab. inż.
PeopleGraduated from the mathematical class at the Nicolaus Copernicus High School in Gdańsk (1974). Master of Sciences in Civil Engineering after studies at Gdansk University of Technology (GUT), Poland (1974-1979). Since 1979 became an employee of the GUT. In 1989 earned a Ph.D. degree in Civil Engineering (with grade "Summa cum Laude") from the GUT. In 2008 obtained a D. Sc. (Habilitation) degree in Civil Engineering (with grade...
-
Jacek Tejchman prof. dr hab. inż.
People -
Adam Dąbrowski dr inż.
PeopleAdam Dabrowski has obtained a PhD in mechanical engineering from Gdańsk University of Technology and MSc. degree in mechatronics from Technische Universität Hamburg. He has an industry experience in Institute of Aviation Engineering Design Center (Warsaw, Poland) and SICK AG (Hamburg, Germany). Additionally, as an assistant at Gdansk University of Technology he teaught courses on mechanics, space mechanisms and dynamics of space...