displaying 1000 best results Help
Search results for: VIBRATION CORRELATION TECHNIQUE
-
Analysis of pesticide residue in tomato samples using analytical protocol based on application of QuEChERS technique and GC-ECD system
PublicationQuEChERS sample preparation method was used for the determination of 10 pesticides and their metabolites in tomato samples, coupled to gas chromatography with electron capture detector (GCECD). The experimental parameters including oven temperature program, amount of the sample and purifying agent were optimized. The GC-ECD method was validated in terms of linearity, selectivity and recovery. The limits of detection (LODs) of the...
-
Identification of predicted genes expressed differentially in pituitary gland tissue of young growing bulls revealed by cDNA-AFLP technique
Publication -
Extended-spectrum beta-lactamase-producing Klebsiella pneumoniae in a neonatal unit: control of an outbreak using a new ADSRRS technique
PublicationSzczepy Klebsiella pneumoniae (EPKP)produkujące beta-laktamazy o rozszerzonym spektrum substratowym (ESBL)stanowią często problem zakażeń na oddziałach noworodkowych. Izolaty od 149 pacjentów poddano typowaniu nową metodą opartą na zjawisku supresji PCR, ADSRRS-fingerprinting, wykazując pochodzenie klonalne badanych szczepów. Użyteczność techniki ADSRRS-finerprinting została potwierdzona innymi metodami - RAPD i PFGE.
-
Computer simulation of vibration surveillance of discretely idealised mechanical systems. Part I: Optimal control at the energy performance index for open non-stationary systems
PublicationPraca dotyczy sposobów nadzorowania drgań mechanicznych z wykorzystanie elementów teorii sterowania, optymalizacji dynamicznej, nowoczesnych metod symulacji komputerowej oraz technik pomiarowych. Do modelowania niestacjonarnego układu sterowanego zastosowano mieszaną metodą sztywnych i odkształcalnych elementów skończonych. Opracowano metodę nadzorowania drgań w dziedzinie czasu, z wykorzystaniem sterowania optymalnego przy energetycznym...
-
Two-phase water-air flow measurement using gamma-ray absorption technique – plug flow
Open Research DataThe attached datasets contains the measurement results of the air-water flow in a horizontal pipeline. Flow type: plug flow. The data shows the pulse counts of the two radiometric sets. Each of these kits consisted of a QSA Global Am-241 gamma ray source and a Tesla SKG-1 type NaI(Tl) scintillation probe. The pulses were recorded using a dedicated EC...
-
Two-phase water-air flow measurement using gamma-ray absorption technique – slug flow
Open Research DataThe attached datasets contains the measurement results of the air-water flow in a horizontal pipeline. Flow type: slug flow. The data shows the pulse counts of the two radiometric sets. Each of these kits consisted of a QSA Global Am-241 gamma ray source and a Tesla SKG-1 type NaI(Tl) scintillation probe. The pulses were recorded using a dedicated EC...
-
Two-phase water-air flow measurement using gamma-ray absorption technique –bubble flow
Open Research DataThe attached datasets contains the measurement results of the air-water flow in a horizontal pipeline. Flow type: bubble flow. The data shows the pulse counts of the two radiometric sets. Each of these kits consisted of a QSA Global Am-241 gamma ray source and a Tesla SKG-1 type NaI(Tl) scintillation probe. The pulses were recorded using a dedicated...
-
Effect of the Combined Therapy of the Muscle Energy Technique and Trigger Point Therapy on the Biophysical Parameters of the Trapezius Muscle: a Randomized Clinical Trial
Publication -
A Salp-Swarm Optimization based MPPT technique for harvesting maximum energy from PV systems under partial shading conditions
Publication -
Production of the anticancer drug taxol by the endophytic fungus Epicoccum nigrum TXB502: enhanced production by gamma irradiation mutagenesis and immobilization technique
Publication -
The efficiency comparison of ramentaceone isolation from Drosera aliciae plants using normal and reversed phase preparative liquid chromatography technique
PublicationW pracy zaprezentowano optymalne warunki otrzymywania ramentaceonu z chloroformowego ekstraktu z rośliny D. muscipula. Opracowano i przedstawiono dwie procedury otrzymywania ramantaceonu z wykorzystaniem NP-PLC i RP-PLC. Dla produktu o określonej czystości, porównano maksymalny stopień przeładowania kolumny, efektywność procesu wyrażoną jako ilość substancji otrzymanej w jednostce czasu oraz produktywność kolumny, wyrażoną jako...
-
Analysis of pesticide residue in fruits and vegetables using analytical analytical protocol based on application of QuEChERS technique and GC-ECD system
PublicationQuEChERS sample preparation method was used for the determination of 10 pesticides and their metabolites in fruits (apple, grape) and vegetables (tomato, paprika), coupled to gas chromatography with electron capture detector (GC-ECD). The experimental parameters including amount of the sample, types of solvents, extraction time and types of sorbent at the purification stage were optimized. The GC-ECD method was validated in terms...
-
Comparison of Evaluation of Air Odour Quality in Vicinity of Petroleum Plant Using a Prototype of Electronic Nose Instrument and Fast GC Technique
PublicationThe paper presents the results of investigation on classification of the ambient air samples collected in a vicinity of the LOTOS Group S.A. petroleum plant with respect to odour. The investigations were carried out with an electronic nose prototype and a commercial electronic nose of Fast GC-type – HERACLES II. The prototype was equipped with a set of six semiconductor sensors by FIGARO Co. and a photoionization sensor of PID-type....
-
Correlation between the Reactivity and Spectroscopic Properties of N-Substituted Secondary Thioamides. New Intramolecular N• •H+• •N Binding Approach and Proton Complexes Based on Thioamide Ligation
PublicationFrom a comparison of chem. shifts and wavenumbers of several secondary thioamides and amides having monocationic substituents attached to thiocarbamoyl or carbamoyl groups by a polymethylene chain, new intramol. unconventional N···H+···N H bonding effects were discovered. It is argued that the CH2-N rotation is hindered and two +H···NHMe nonequiv. protons occur in a proton spectrum of hydrochloride RCH2C(S)NH(CH2)3NHMe-HCl...
-
Earthquake Engineering and Engineering Vibration
Journals -
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Volume optimization of high-speed surface-mounted permanent magnet synchronous motor based on sequential quadratic programming technique and analytical solution
Publication -
Experimental investigation on welding of 2.25 Cr-1.0 Mo steel with regulated metal deposition and GMAW technique incorporating metal-cored wires
Publication -
Air-coupled ultrasonic C-scan technique in impact response testing of carbon fibre and hybrid: glass, carbon and Kevlar/epoxy composites.
PublicationTradycyjnie badania nieniszczące laminatów metodą ultradźwiękową przeprowadza się w ośrodku wodnym. W pracy podano wyniki badań rozmiaru strefy zniszczeń w laminatach epoksydowych zbrojonych włóknami szklanymi, węglowymi i aramidowymi metodą ultradźwiękową z powietrzem jako ośrodkiem sprzęgającym próbkę, nadajnik i odbiornik. Wyniki porównano z wynikami badań rentgenowskich z zastosowaniem penetranta -jodku cynku. Uzyskano dobrą...
-
Zastosowanie techniki dozymetrii pasywnej do oceny jakości powietrza wewnętrznego. Application of passive sampling technique for assessment of indoor air quality
PublicationJakość powietrza wewnętrznego jest istotnym parametrem wpływającym na dobre samopoczucie i zdrowie człowieka. Kluczowego znaczenia nabiera więc jego nieustanna kontrola i oznaczanie zawartości zanieczyszczeń, które występują w nim na bardzo niskich poziomach stężeń. Do pomiarów jakości powietrza wewnętrznego często wykorzystywana jest (znana od ponad pół wieku) technika dozymetrii pasywnej. W literaturze nadal pojawiają się doniesienia...
-
Simulation of hybridized nanofluids flowing and heat transfer enhancement via 3-D vertical heated plate using finite element technique
PublicationThe present study probed the creation of heat energy and concentrating into Newtonian liquids across vertical 3D-heated plates. The role of the Soret and Dufour theories in concentrating and energy formulas is discussed. The role of hybrid nanoparticles is introduced to illustrate particle efciency in terms of solute and thermal energy. It is removed a viscous dissipation process and a changing magnetic feld. The proposed approach...
-
Modelling hydraulic and capillary-driven two-phase fluid flow in unsaturated concretes at the meso-scale with a unique coupled DEM-CFD technique
PublicationThe goal of the research was to demonstrate the impact of thin porous interfacial transition zones (ITZs) between aggregates and cement matrix on fluid flow in unsaturated concrete caused by hydraulic/capillary pressure. To demonstrate this impact, a novel coupled approach to simulate the two-phase (water and moist air) flow of hydraulically and capillary-driven fluid in unsaturated concrete was developed. By merging the discrete...
-
Two-phase water-air flow measurement using gamma-ray absorption technique – transitional plug – bubble flow
Open Research DataThe attached datasets contains the measurement results of the air-water flow in a horizontal pipeline. Flow type: transitional plug – bubble flow. The data shows the pulse counts of the two radiometric sets. Each of these kits consisted of a QSA Global Am-241 gamma ray source and a Tesla SKG-1 type NaI(Tl) scintillation probe. The pulses were recorded...
-
Ethylcellulose in Organic Solution or Aqueous Dispersion Form in Designing Taste-Masked Microparticles by the Spray Drying Technique with a Model Bitter Drug: Rupatadine Fumarate
Publication -
Membrane in tandem with a helical sorbent trap as continuous sampling technique of the polyvinyl chloride thermo-oxidative degradation products for their on-line gas chromatographic monitoring
Publication -
Simultaneous determination of hydrophobicity and dissociation constant for a large set of compounds by gradient reverse phase high performance liquid chromatography–mass spectrometry technique
Publication -
Multi-Technique Investigation of Grave Robes from 17th and 18th Century Crypts Using Combined Spectroscopic, Spectrometric Techniques, and New-Generation Sequencing
PublicationThe textile fragments of the funeral clothes found in the 17th and 18th century crypts were subjected to spectroscopic, spectrometric, and microbial investigation. The next-generation sequencing enabled DNA identification of microorganisms at the genus and in five cases to the species level. The soft hydrofluoric acid extraction method was optimized to isolate different classes of dyes from samples that had direct contact with...
-
Identification of lipid fraction constituents from grasshopper (Chorthippus spp.) abdominal secretion with potential activity in wound healing with the use of GC–MS/MS technique
Publication -
Elemental composition analysis of Pistacia lentiscus L., leaves collected from Mitidja plain in Algeria using instrumental neutron activation analysis (INAA) technique
Publication -
Power Grid Frequency Estimation Based on Zero Crossing Technique Using Least Squares Method to Approximate Sampled Voltage Signal Around Zero Level
Publication -
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublicationAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
Krzysztof Wilde prof. dr hab. inż.
PeopleKrzysztof Wilde (born January 11th, 1966 in Gdańsk) – expert in bridge structures, structural mechanics and diagnostics of civil structures. He conducted research on vibration reduction systems for bridges exposed to dynamic loads from winds and earthquakes. At present he is interested in the field of nondestructive testing of materials and structural health monitoring systems. Hi is author or coauthor of over 200 publications...
-
Selected Aspects of 3D Printing for Emergency Replacement of Structural Elements
PublicationThe paper presents a synthetic characterization of modern methods of manufacturing or regenerating machine elements. Considered methods are machining and additive methods, in particular 3D printing in the FDM/FFF technique. For the study, the authors made samples of the holder bracket using selected methods. Samples made by machining operations, 3D printing with various filling were tested. The paper contains a technical and economic...
-
Michał Mazur dr inż.
PeopleAktualne zainteresowania inżynieria mechaniczna, robotyka, drgania mechaniczne, analiza modalna, sterowanie, systemy czasu rzeczywistego Wybrane publikacje Kaliński K., Galewski M., Mazur M., Chodnicki M, 2017, Modelling and Simulation Of A New Variable Stiffness Holder for Milling Of Flexible Details, Polish Maritime Research, vol 24, ss. 115-124 Kaliński K. J., Mazur M.: Optimal control at energy performance index of the mobile...
-
A general method for the derivation of the functional forms of the effective energy terms in coarse-grained energy functions of polymers. III. Determination of scale-consistent backbone-local and correlation potentials in the UNRES force field and force-field calibration and validation
Publication -
New procedure of silica gel surface modification-preparation of gaseous standard mixtures of methyl chloride using the technique of thermal decomposition of the surface compound for calibration of a TD-GC-FID system.
PublicationPrzedstawiono nową procedurę modyfikacji powierzchni żelu krzemionkowego w celu wytworzenia związku powierzchniowego będącego źródłem chlorku metylu. Minimalna temperatura rozkładu (150 st. C) zapewnia trwałość chemicznie modyfikowanego złoża w temp. pokojowej. Badania prowadzono w temperaturze optymalnej (280 st.C). Stwierdzono, że powierzchnia żelu jest obsadzona jednorodnie przez związek powierzchniowy i gazowa mieszanina wzorcowa...
-
DLC coating in ring-on-ring sliding with water lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was augmented by vibration...
-
DLC coating in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h. The test was augmented...
-
DLC coating in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h. The test was augmented...
-
DLC coating in ring-on-ring sliding with water lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was augmented by vibration...
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
PublicationIn this work results of numerical simulations and experimental measurements related to the high frequency dynamics of an aluminium Timoshenko periodic beam are presented. It was assumed by the authors that the source of beam structural periodicity comes from periodical alterations to its geometry due to the presence of appropriately arranged drill-holes. As a consequence of these alterations dynamic characteristics of the beam...
-
Paweł Wierzba dr hab. inż.
PeopleDr Paweł Wierzba, E.E. M.Sc. E.E. received from WETI PG 1994 PhD in optoelectronics (with honours) from WETI PG 2001 Research Stays at VTT Technical Research Centre of Finland from 1997 to 2000 Finnish Academy Scholarship at VTT Technical Research Centre of Finland (12 months) 2002-3 Research interest area covers optical and optical fiber meaurement methods, technology of selected ceramic and liquid crystalline materials relevant...
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
Discussion of “Development of an Accurate Time integration Technique for the Assessment of Q-Based versus h-Based Formulations of the Diffusion Wave Equation for Flow Routing” by K. Hasanvand, M.R. Hashemi and M.J. Abedini
PublicationThe discusser read the original with great interest. It seems, however, that some aspects of the original paper need additional comments. The authors of the original paper discuss the accuracy of a numerical solution of the diffusion wave equation formulated with respect to different state variables. The analysis focuses on nonlinear equations in the form of a single transport equation with the discharge Q (volumetric flow rate)...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
Modeling of free vibrations and resonant frequencies of simply-supported submerged horizontal plate
PublicationA theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases...
-
Optical-Spectrometry-Based Method for Immunosuppressant Medicine Level Detection in Aqueous Solutions
PublicationIn this paper, an investigation into detecting immunosuppressive medicine in aqueous solutions using a spectrometry-based technique is described. Using optical transmissive spectrometry, absorbance measurements in the spectra range from 250 nm to 1000 nm were carried out for different cyclosporine A (CsA) concentrations in aqueous solutions. The experiment was conducted for samples both with and without interferent substances—glucose...