Filters
total: 1212
-
Catalog
displaying 1000 best results Help
Search results for: maritime%20transportation
-
NEW CONCEPT OF HYBRID PROPULSION WITH HYDROSTATIC GEAR FOR INLAND WATER TRANSPORT
PublicationThe article presents the development of author’s concept of a diesel/hydraulic propulsion system for inland watercraft. Due to specific nature of vessel navigation on rivers, classical propulsion systems with shaft lines can be effectively replaced by systems with hydraulic power transmission. A solution is also presented of a hybrid design with extra electric port having the form of a pumping system driven from a battery of accumulators....
-
CFGFRPT Piles with a Circular Cross-Section and their Application in Offshore Structures
PublicationThe possibilities of using concrete piles in a polymer composite reinforced with glass fibres in offshore facilities were shown. Laboratory tests of CFGFRPT type piles compressed axially and in eccentric compression for the analysis of CFGFRPT piles were used. Methods of analysis of dynamic systems for mathematical modelling of the displacement of the hammer in the pile driving process were applied. The possibilities of combining...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublicationThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublicationThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Model Predictive Super-Twisting Sliding Mode Control for An Autonomous Surface Vehicle
PublicationThis paper presents a new robust Model Predictive Control (MPC) algorithm for trajectory tracking of an Autonomous Surface Vehicle (ASV) in presence of the time-varying external disturbances including winds, waves and ocean currents as well as dynamical uncertainties. For fulfilling the robustness property, a sliding mode control-based procedure for designing of MPC and a super-twisting term are adopted. The MPC algorithm has been...
-
Numerical Analysis of an Impact of Planned Location of Sewage Discharge on Natura 2000 Areas – The Dead Vistula Region Case Study
PublicationThis article presents results of an analysis of impact of a designed discharge of contaminated water into the Dead Vistula (Wisła Martwa) in the region of the Isthmus (Przesmyk) with the aim of determination of a possible effect of the pollution onto protected areas of Natura 2000 (bird habitats and sites, especially the Bird Paradise – Ptasi Raj) nature reserve. The analysis was conducted on the basis of the two-dimensional modelling...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Multi-objective weather routing of sailboats considering wave resistance
PublicationThe article presents a method to determine the route of a sailing vessel with the aid of deterministic algorithms. The method assumes that the area in which the route is to be determined is limited and the basic input data comprise the wind vector and the speed characteristic of the vessel. Compared to previous works of the authors, the present article additionally takes into account the effect of sea waves with the resultant resistance...
-
Bearing estimation using double frequency reassignment for a linear passive array
PublicationThe paper demonstrates the use of frequency reassignment for bearing estimation. For this task, signals derived from a linear equispaced passive array are used. The presented method makes use of Fourier transformation based spatial spectrum estimation. It is further developed through the application of two-dimensional reassignment, which leads to obtaining highly concentrated energy distributions in the joint frequency-angle domain...
-
Theoretical Model of Acoustic Wave Propagation in Shallow Water
PublicationThe work is devoted to the propagation of low frequency waves in a shallow sea. As a source of acoustic waves, underwater disturbances generated by ships were adopted. A specific feature of the propagation of acoustic waves in shallow water is the proximity of boundaries of the limiting media characterised by different impedance properties, which affects the acoustic field coming from a source situated in the water layer “ deformed”...
-
Features of load and wear of main propulsion devices on sea-going ships with piston combustion engines and their impact on changes in technical states of the systems
PublicationThe paper presents the specificity of operation of propulsion systems of seagoing ships which causes the need to control the load on them, especially on their engines called main engines. The characteristics of the load on the propulsion systems, especially on the main engines as well as on the shaft lines and propellers driven by the engines, along with the process of wear in tribological joints (sliding tribological systems)...
-
Design of Structure of Tension Leg Platform for 6 MW Offshore Wind Turbine Based On Fem Analysis
PublicationThe article presents the calculation and design stages of the TLP platform serving as a supporting construction of a 6 MW offshore wind turbine. This platform is designed to anchor at sea at a depth of 60 m. The authors presented the method of parameterization and optimization of the hull geometry. For the two selected geometry variants, the load and motion calculations of the platform subjected to wind, wave and current under...
-
Technology Concept of TLP Platform Towing and Installation in Waters with Depth of 60 m
PublicationThe article is part of the design and research work conducted at the Gdansk University of Technology, Faculty of Ocean Engineering and Ship Technology, in cooperation with a number of other research centres, which concerns offshore wind farms planned to be built in the Polish zone of the Baltic sea in the next years. One of most difficult tasks in this project is building suitable foundations for each power unit consisting of a...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
MAPPING SOUTH BALTIC NEAR-SHORE BATHYMETRY USING SENTINEL-2 OBSERVATIONS
PublicationOne of the most promising new applications of remote observation satellite systems (RO) is the near-shore bathymetry estimation based on spaceborn multispectral imageries. In recent years, many experiments aiming to estimate bathymetry in optically shallow water with the use of remote optical observations have been presented. In this paper, optimal models of satellite derived bathymetry (SDB) for relatively turbid waters of the...
-
Technical State Assessment of Charge Exchange System of Self-Ignition Engine, Based On the Exhaust Gas Composition Testing
PublicationThis paper presents possible use of results of exhaust gas composition testing of self - ignition engine for technical state assessment of its charge exchange system under assumption that there is strong correlation between considered structure parameters and output signals in the form of concentration of toxic compounds (ZT) as well as unambiguous character of their changes. Concentration of the analyzed ZT may be hence considered...
-
Visualization of a lifeboat motion during lowering along ship’s side
PublicationThis paper presents description of a computer program for motion visualization of a lifeboat lowered along ship’s side. The program is a post-processor which reads results of numerical calculations of simulated objects’ motions. The data is used to create scene composed of 3D surfaces to visualize mutual spatial positions of a lifeboat, ship’s side and water waving surface. Since the numerical data contain description of a simulation...
-
A method to assess transverse vibration energy of ship propeller shaft for diagnostic purposes
PublicationThe article discusses a key problem of ship propulsion system vibration diagnostics, which concerns assessing this part of mechanical energy transmitted from the main engine to the ship propeller which is dissipated due to propeller shaft vibration. A simplified calculation model is proposed which allows the total energy of the generated torsional vibration to be assessed from the shaft deflection amplitude measured at the mind-span...
-
Acoustic imaging of selected areas of Gdansk Bay with the aid of parametric echosounder and side-scan sonar
PublicationThe article presents and analyses the data recorded during sounding of the Gdansk Bay seabed with the aid of a parametric echosounder and a side-scan sonar. The accuracy of seabed structure examination, as a condition for obtaining valuable results, requires correct configuration of echolocation devices and proper calibration of peripheral devices, such as the survey unit geographical position sensor – GPS, the navigation unit,...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
ENERGY EFFICIENT AND ENVIRONMENTALLY FRIENDLY HYBRID CONVERSION OF INLAND PASSENGER VESSEL
PublicationThe development and growing availability of modern technologies, along with more and more severe environment protection standards which frequently take a form of legal regulations, are the reason why attempts are made to find a quiet and economical propulsion system not only for newly built watercraft units, but also for modernised ones. Correct selection of the propulsion and supply system for a given vessel affects significantly...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublicationThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions
PublicationThe focus of this paper is on process planning for large parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centres. The analysis of machining heavy mechanical components used in off-shore constructions has been carried out. Setup concepts applied and operation sequences determined in related process plans underwent studies. The paper presents in particular a reasoning approach...
-
Searching for Critical Conditions During Lifeboat Launching – Simulations
PublicationThe article describes numerical simulations of the process of lifeboat launching at the ship’s side. The research is aimed at finding the values of ship motion parameters which appear to be most dangerous for people in the lowered lifeboat due to the generated accelerations. The simplified model of ship hull motion adopted at this research stage bases on a superposition of harmonic motions with given amplitudes and periods in six...
-
Investigation method and mathematical model of pressure losses in hydraulic rotary motor
PublicationTis paper presents a way of determining the coefcient k of the pressure losses Δp (fow drag) in internal ducts 8 Mp of SWSB-63 hydraulic motor. Te coefcient is determined at a fow rate equal to the theoretical capacity Q of the Pt pump feeding the motor , the losses are related to the nominal pressure p in the hydraulic system. Te investigations n followed a model of energy performance of hydraulic rotary motor, proposed by...
-
Effect of Different Structure Type Traffic On Railway Line Capacity
PublicationThe article points to methods of analyzing railway traffic conditions based on two parameters: capacity and delay of trains. The impact of the differentiated railway type structure on the capacity of the railway line was presented. Particular attention has been paid to the assessment of commonly used simplifications in analyzes.
-
Comparison of soil models in the thermodynamic analysis of a submarine pipeline buried in seabed sediments
PublicationThis paper deals with mathematical modelling of a seabed layer in the thermodynamic analysis of a submarine pipeline buried in seabed sediments. The existing seabed soil models: a “soil ring” and a semi-infinite soil layer are discussed in a comparative analysis of the shape factor of a surrounding soil layer. The meaning of differences in the heat transfer coefficient of a soil layer is illustrated based on a computational example...
-
A new modelling arrangement for testing of Catenary Anchoring Leg Mooring (CALM) system behaviour in waves
PublicationW artykule przedstawiono układ modelowy pławy cumowniczo-przeładunkoweji łańcuchów kotwicznych możliwy do realizacji w wydłużonych basenach falowych służących na co dzień do badania właściwości morskich statków. System łańcuchów kotwicznych sprowadzono do płaszczyzn równoległych do osi basenu i połączono z pławą cienkimi linkami stalowymi przechodzącymi przez bloczki kierunkujące. Opisywany układ pozwolił na przeprowadzenie badań...
-
Influence of the steam within seals and glands of the turbine on its rotor motion stability.
PublicationPrzedstawiono metodę obliczania charakterystyk dynamicznych wpływu parowych uszczelnień turbin na ich dynamikę i stateczność ruchu wirników. Zarysowano model ''masowy'' uszczelnienia. Podano przykłady zastosowań.
-
On application of the Case-Based Reasoning methods in ship automation design
PublicationW artykule przedstawiono metodę wnioskowania na podstawie przypadków oraz dwa przykłady jej zastosowania w projektowaniu statków. Pierwszy przykład dotyczy systemu projektowania koncepcyjnego statku. Drugi przykład odnosi się do projektowania układów automatyki okrętowej. Omówiono szczegółowo problemy doboru funkcji podobieństwa w metodzie wnioskowania na podstawie przypadków.
-
A concept of application of the technical state change models of devices inship operation process
PublicationPrzedstawiono warunki zastosowania modeli zmian stanu technicznego urządzeń siłowni okrętowej w trakcie eksploatacji statku, koncepcję prognozowania zasobu godzin pracy urządzeń w zmiennych warunkach pływania oraz planowania obsług profilaktycznych.
-
Ship roll damping moments
PublicationWprowadzono nieliniową formę współczynnika tłumienia kołysań bocznych statku oraz jego ekwiwalentną liniową formę. Zastępczy liniowy współczynnik tłumienia może być określony na podstawie kołysań. Przedstawiono przykładowe wyniki nieliniowego współczynnika tłumienia dla promu pasażerskiego "Polonia".
-
Deterministic and probabilistic interpretation of operation of technicalsystems with regard to their reliability
PublicationZaproponowano interpretację wartościującą działanie, które jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej dżulosekundą [dżulxsekunda]. Tak rozumiane działanie przedstawiono w ujęciu technicznym. Zaproponowano oryginalną metodę analizy i oceny działania dowolnego systemu technicznego z uwzględnieniem jego niezawodności. Szczególną uwagę zwrócono na interpretację działania silnika o zapłonie samoczynnym. Do uzasadnienia...
-
On possible lowering fuel oil consumption by differentiating loads on ship diesel engines running in parrallel.
PublicationPodano możliwości zmniejszenia zużycia paliwa przez silniki okrętowe pracujące równolegle dzieki różnicowaniu ich obciążeń eksploatacyjnych. Zaprezentowano podstawy teoretyczne oraz sposób postępowania przy pomiarach zużycia paliwa w czasie rzeczywistym.
-
Influence of adjustment of gas turbine controller on ship propulsion system behaviour in rough sea conditions. Part 1. The dynamic model of propulsion system.
PublicationPrzedstawiono model dynamiki układu napędowego okrętowego, wykorzystując metodę elementów skończonych. Układ napędowy składa się z dwóch turbin gazowych napędzających poprzez przekładnię mechaniczną zębatą pędnik o nastawnym skoku. W symulacji układu napędowego można zadawać wymuszenia wartością zadaną nastaw prędkości na regulatorze, wymuszenia od falowania morza w zależności od stanu morza, jak również zmianą ustawienia skoku...
-
Accuracy Of The GPS Positioning System In The Context Of Increasing The Number Of Satellites In The Constellation
Publication -
Position accuracy evaluation of the modernized Polish DGPS
Publication -
Application of an Autonomous/Unmanned Survey Vessel (ASV/USV) in Bathymetric Measurements
Publication -
Polish DGPS System: 1995–2017 – Study of Positioning Accuracy
Publication -
A Method for The Assessing of Reliability Characteristics Relevant to an Assumed Position-Fixing Accuracy in Navigational Positioning Systems
PublicationThis paper presents a method which makes it possible to determine reliability characteristics of navigational positioning systems, relevant to an assumed value of permissible error in position fixing. The method allows to calculate: availability , reliability as well as operation continuity of position fixing system for an assumed, determined on the basis of formal requirements - both worldwide and national, position-fixing accuracy....
-
Elżbieta Marczak dr inż. arch.
PeopleElżbieta Marczak (Architect, Phd) – Assistant Professor at the Faculty of Architecture, Gdańsk University of Technology, Department of Urban Architecture and Waterscapes (since 1997). Studies at the Faculty of Architecture GUT graduated in 1995. Degree of Doctor obtained in 2006 presenting dissertation The ship’s architecture against the background of the maritime transport development. Her research and publications focus on...
-
Andrzej Wojewódka mgr inż.
People -
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublicationThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
GNSS INVENTORY OF HISTORIC NARROW-GAUGE RAILWAY LINE IN KOSZALIN UNDER EXTREMELY UNFAVORABLE MEASUREMENTS CONDITIONS FROM THE POINT OF VIEW OF SATELLITE SIGNALS AVAILABILITY
PublicationA team of academic researchers from the Gdańsk University of Technology, Gdynia Maritime University and the Polish Naval Academy have been working since 2009 on the methodology of using active GNSS geodetic networks for geodetic inventory of railways and on adapting this measurement technique for designing geometric layouts of railway and tram lines. Over the years, the team tested a variety of configurations of receivers and settings...
-
Three-dimensional geographically weighted inverse regression (3GWR) model for satellite derived bathymetry using Sentinel-2 observations
PublicationCurrent trends of development of satellite derived bathymetry (SDB) models rely on applying calibration techniques including analytical approaches, neuro-fuzzy systems, regression optimization and others. In most of the cases, the SDB models are calibrated and verified for test sites, that provide favourable conditions for the remote derivation of bathymetry such as high water clarity, homogenous bottom type, low amount of sediment...
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublicationIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
South Coast Baltic Establishing durable cross-border boating destination management on the basis of the MARRIAGE cooperation network
ProjectsProject realized in Department of Management according to STHB.02.01.00-DE-0070/16-00 agreement from 2017-02-28
-
Down-Sampling of Large LiDAR Dataset in the Context of Off-Road Objects Extraction
PublicationNowadays, LiDAR (Light Detection and Ranging) is used in many fields, such as transportation. Thanks to the recent technological improvements, the current generation of LiDAR mapping instruments available on the market allows to acquire up to millions of three-dimensional (3D) points per second. On the one hand, such improvements allowed the development of LiDAR-based systems with increased productivity, enabling the quick acquisition...