Search
Search results for: COLD C
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Active Dynamic Infrared Thermal Imaging in Burn Depth Evaluation
PublicationThe aim of this study was to find the relationship between active dynamic thermography (ADT) with cold excitation and burn depth. This new modality of evaluation of burns seems to be an attractive proposal for quantitative classification, allowing proper choice of burn wound treatment: conservative or surgical, especially compared with static thermography. The work was an in vivo experiment on domestic pigs, and a small number...
-
Stability of an Innovative Cold-Formed GEB Section
PublicationThis paper is focused on the numerical analysis and experimental test of stability of the cold-formed profile with an innovative GEB cross-section. For the shell model of the axially compressed member, the linear buckling analysis and the nonlinear static analysis were carried out. In the numerical research, the buckling load and the limit load for variable section heights were obtained. Some of the results were compared with the...
-
Comparison of perforator location in dynamic and static thermographic imaging with Doppler ultrasound in breast reconstruction surgery
PublicationThis paper co mpares the effectiveness of the dTnorm and t90_10 parametrizations in dynamic thermography for imaging location of perforators in TRAM flaps in the intraoperative period. The results were compared with the location detected in a Doppler ultrasound examination. Cold and heat stimulation was used in dynamic thermography. Additionally, these results were compared with static...
-
Structural studies of a cold-adapted dimeric Beta-D-galactosidase from Paracoccus sp. 32d
PublicationThe crystal structure of a novel dimeric [beta]-D-galactosidase from Paracoccus sp. 32d (Par[beta]DG) was solved in space group P212121 at a resolution of 2.4 Å by molecular replacement with multiple models using the BALBES software. This enzyme belongs to glycoside hydrolase family 2 (GH2), similar to the tetrameric and hexameric [beta]-D-galactosidases from Escherichia coli and Arthrobacter sp. C2-2, respectively. It is the second...
-
TSR method for burns investigation approach
PublicationThe article presents the possibilities of applying the TSR method for the diagnosis of burn wounds. The wound area is stimulated by cold gas and a sequence of thermograms of heating the tissue is recorded. Next, TSR algorithms are used to determine the parameters that allow the wound to be classified into one of the classes: the wound heals within three weeks, the wound will not heal in three weeks. The method was...
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublicationThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Local buckling and initial post-buckling behaviour of channel member flange - analytical approach
PublicationThe local buckling and initial post-buckling behaviour of the cold-formed channel member flange is investigated. The governing nonlinear differential equation for axially compressed columns and beams undergoing pure bending is derived using the stationary total potential energy principle. The critical stress and initial post-buckling equilibrium path is determined by means of a perturbation approach. The results obtained allow...
-
Load carrying capacity of the eccentric joint in the truss made of open cross-sections
PublicationThe influence of eccentricity at intersections of truss members on the load carrying capacity of the truss joint is presented in the paper. The research truss elements were designed as cold-formed open cross section. Analytical calculations, numerical analysis and experimental research were conducted to reveal how the eccentricity affects the effort of material in the joint area. The results of analysis and investigations are compared...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Effect of long-term cold storage on physicochemical attributes and bioactive components of kiwi fruit cultivars
PublicationVarious kiwi fruit cultivars, bred in Korea, were kept in cold storage for 8–24 weeks for possible increase of their quality. Firmness significantly decreased at initial time in all cultivars.The rate of softeningwas the slowest in “Hayward”, followed by “Hort16A”, “Haenam”, “Daheung”, “Bidan”, “Hwamei”, and “SKK 12”. Sensory value increased with decreasing of firmness. Soluble solids content increased with storage time while acidity gradually...
-
Mercury in various components of the environment (Gulf of Gdańsk, southern Baltic Sea)
PublicationTotal mercury concentration was determined monthly form January 2012 to May 2013 in the water (microlayer and the surface), plankton, epilithon, epiphyton, benthos and sediment. The study was conducted in the coastal zone of the Gulf of Gdańsk. The abundance and biomass of plankton, benthos; the concentration of suspended particulate matter, particulate organic carbon and nitrogen; δ13C and δ15N in the suspended matter; sediment...
-
The validation process of truss model with joint eccentricities
PublicationNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
CLASSIFICATION OF RESTRAINTS IN THE OPTIMIZATION PROBLEM OF A COLD-FORMED PROFILE
PublicationThis work describes the restraints in the optimization problem. This is an important and complicated issue because it requires taking into account a vast range of information related to the design and production. In order to describe the relations of a specific optimization problem, it is essential to adopt appropriate criteria and to collect information on all kinds of restraints, i.e. boundary conditions. The following paper...
-
Context-aware User Modelling and Generation of Recommendations in Recommender Systems
PublicationRecommender systems are software tools and techniques which aim at suggesting new items that may be of interest to a user. This dissertation is focused on four problems in recommender systems domain. The first one is context-awareness, i.e. how to obtain relevant contextual information, how to model user preferences in a context and use them to make predictions. The second one is multi-domain recommendation, which aim at suggesting...
-
Potential energy surfaces of the low-lying electronic states of the Li+LiCs system
PublicationAb initio quantum chemistry calculations are performed for the mixed alkali triatomic system. Global minima of the ground and first excited doublet states of the trimer are found and Born-Oppenheimer potential energy surfaces of the Li atom interacting with the LiCs molecule were calculated for these states. The lithium atom is placed at various distances and bond angles from the lithium-caesium dimer. Three-body nonadditive forces...
-
The biotic and abiotic mercury at the coastal zone of Gulf of Gdańsk
Open Research DataConcentration of neurotoxin Hg (mercury) was determined monthly form 01.2012 to 05.2013 (total and suspended) in the surface microlayer and the surface water as well as in: phytoplankton, zooplankton, epilithon, epifithon, phytobenthos (macroalgae and angiosperms), zoobenthos, and in the sediment. The study was conducted in the coastal zone of the Puck...
-
Deflection measurement of field section with pavement with base course made of Cement Bitumen Treated Material Mixture C3E4 (28, 180, 270, 365 days after compaction)
Open Research DataDataset presents data of deflections determined for pavement with base course made of cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in stationary plant and compacted...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Normal stress distribution in built‑up cold‑formed column in relation to interconnecting bolt spacing
PublicationIn order to increase a stiffness of cold-formed steel (CFS) elements it is practised to built-up the cross-section. In the analysed case, a main element is strengthened by adding extra chord in contact partially along the column. This additional chord acts as a longitudinal stiffener connected with the main section by series of bolts. Authors check whether rules applied over the years, for hot-rolled elements, can be indiscriminately...
-
Stability and limit load analysis of a cold-formed channel section column
PublicationThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublicationDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
WSPÓŁPRACA BLOKU GAZOWO-PAROWEGO Z OBIEGIEM ORC = Combinded power plant in cooperation with ORC
PublicationIn the paper presented is the idea of a combined gas and steam power plant cooperation with a low temperature organic Rankine cycle ORC unit. Considerations presented in the paper are accomplished for the Gorzów CHP. The intention of present analysis is heat recovery of low temperature energy and its further use in ORC cycle in order to produce electricity, without increase in fuel consumption. Waste energy is recovered from the...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Beta-galactosidases from a psychrotolerant Arthrobacter isolates and their potential use
PublicationEnzymes from extremophiles, especially psychrophiles and psychrotolerant microorganisms are currently intensively studied because of their unusual structural and functional properties. One of these enzymes is a cold-adapted - galactosidase (EC 3.2.1.23) which catalyzes the hydrolysis of - 1,4-glycosidic bonds in -galactosides. The most common - galactoside is lactose, a disaccharide which makes up 2-7% of milk. The majority of...
-
Buckling and initial post-local buckling behaviour of cold-formed channel member flange
PublicationThe initial post-buckling behaviour of a cold-formed channel member flange after its local buckling is investigated. An axially compressed column or beam subjected to pure bending is considered. The member material is assumed to follow a linear stress-strain relationship. The governing non-linear differential equation of the problem is derived using the minimum total potential energy principle. An approximate solution for the equation...
-
Local buckling of compressed flange of cold-formed channel members made of aluminum alloy
PublicationThe paper deals with local buckling of a compressed single flange of thin-walled channel cold- formed columns and beams made of aluminum alloy. Material is described by means of the Ramberg-Osgood constitutive equation. Axial compression of the columns and beams undergoing bending is taken into consid- eration. A simple model of the member flange in the form a long beam elastically connected to the web is used to find the critical...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Optimization of the femtosecond laser impulse for excitation and the spin-orbit-mediated dissociation in the NaRb molecule
Open Research DataHigh accuracy ab initio potential energy curves (1tSigma+, 2sSigma+, 1tPi), electronic transition dipole moment function (1tSigma+ - 1tPi), and spin-orbit coupling (2sSigma+ - 1tPi) have been calculated for the NaRb molecule. The time-dependent excitation and dissociation processes in the polar alkali diatomic NaRb molecule and the quantum properties...
-
D.C. electrical measurements of Bi2VO5.5 ceramic measured at high temperature region
Open Research DataD.C. electrical properties of Bi2VO5.5 ceramic was measured.
-
Structure of EstA esterase from psychrotrophic Pseudoalteromonas sp. 643A covalently inhibited by monoethylphosphonate.
PublicationThe crystal structure of the esterase EstA from the cold-adapted bacteriumPseudoalteromonas sp. 643A was determined in a covalently inhibited form at aresolution of 1.35 A˚. The enzyme has a typical SGNH hydrolase structureconsisting of a single domain containing a five-stranded beta-sheet, with threehelices at the convex side and two helices at the concave side of the sheet, and isornamented with a couple of very short helices...
-
Natural ventilation performance of family building in cold climate during windy days
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the fresh air inside a building. A prediction of performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long term cost savings. The paper presents results of performance (air change rate ACH) and effectiveness (CO2 concentration in the breathing...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublicationIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
LE STIME ECONOMICHE DELLA CIA E L’IMPREVEDIBILE FINE DELL’URSS
PublicationIn this article, we will analyze the debate that took place around the assessments that the CIA gave of the economic situation in the Soviet Union, a clearly decisive key to understanding the overall health of the main political-military opponent of the United States. The article will include the discussions that flared up in the American political establishment starting in 1990, after the fall of the Berlin Wall and the initial...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Natural ventilation performance of family building in cold climate during windless time
PublicationIn this paper, the field measurements results are presented on the stack ventilation effect. The paper presents the results of performance (air change rate ACH) natural ventilation for building with inlet gap measured for the transitional season (between heating and summer season). The measurements were performed during a windless time. The house was located in northern Poland, in a cold climate region. The measurement system...
-
Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique
PublicationThe paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Comparison of the exponential thermal transient parameterization methods with the SMTP method in the unipedicled DIEP flap computer modelling and simulation
PublicationThe aim of this paper is to compare the spatial contrast of the image descriptors obtained via three different thermal transient parameterization methods in Active Dynamic Thermography. The thermal constants and amplitude values of the one- and two- exponential parametrization are compared to the Simplified Magnitude-Temporal Parametrization method (SMTP). The comparison is performed using the data obtained by simulating the cold...
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublicationThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
Beta-Galactosidases of Pseudoalteromonas sp. – Characteristics and application for lactose hydrolysis and galactopyranosides synthesis
PublicationBeta-galactosidase [EC 3.2.1.23] is an enzyme that catalyzes the hydrolysis of O-glycosidic linkages in galactosides. It has biotechnological applications in the dairy industry for the production of milk with a low content of lactose and galactooligosacharides for use in healthy food. The transgalactosylation activity of beta-galactosidase can be used in the synthesis of alkyl galactopyranosides. Due to the fact that conditions of...
-
Imaging of morphological and physicochemical changes occuring in the structure of austenitic steel due to the thermal sensitization
Open Research DataIn polycrystalline materials, grain boundaries are always where phenomena such as surface diffusion, sedimentation and corrosion occur. They have a significant impact on the macroscopic properties of the construction material [1]. In addition to inhomogeneities such as manganese sulphide inclusions formed during the metallurgical process, interfacial...
-
Linear impedance of Bi2VO5.5 ceramic of thickness 2.88 mm measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of Bi2VO5.5 ceramic of thickness 2.88 mm was measured by impedance spectroscopy method.
-
Linear impedance of Bi2VO5.5 ceramic of thickness 2.52 mm measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of Bi2VO5.5 ceramic of thickness 2.52 mm was measured by impedance spectroscopy method.
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublicationThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Rotational state-changing collisions of C2H− and C2N− anions with He under interstellar and cold ion trap conditions: A computational comparison
PublicationWe present an extensive range of quantum calculations for the state-changing rotational dynamics involving two simple molecular anions that are expected to play some role in the evolutionary analysis of chemical networks in the interstellar environments, C2H− (X1Σ+) and C2N− (X3Σ−), but for which inelastic rates are only known for C2H−. The same systems are also of direct interest in modeling selective photo-detachment experiments...
-
Buckling Analysis of Cold Formed Silo Column
PublicationThe paper is devoted to stability analysis of different models of steel cold formed silo column. The steel cylindrical silos are often composed of corrugated walls and vertical open-sectional columns uniformly placed along the silo circumference. Both the whole 3D silo, a simplified model consisting of one column with a part of the silo walls, and a single column resting on elastic foundation provided by the silo walls were analyzed....