Search
Search results for: OPERATING SYSTEM
-
Study of the Performance of DSSS UAC System Depending on the System Bandwidth and the Spreading Sequence
PublicationA signal transmitted in an Underwater Acoustic Communication (UAC) system operating in a shallow-water channel suffers from strong time dispersion due to multipath propagation. This causes the Inter-Symbol Interference (ISI) observed in the received signal, which significantly limits the communication system’s reliability and transmission rate. In such propagation conditions, the Direct-Sequence Spread Spectrum (DSSS) method is...
-
RESOURCE ALLOCATION IN DAB+ BROADCASTING SYSTEM
PublicationWith over two billion receivers operating worldwide, radio transmission is by far the most accessible medium. It has been a part of our lives since the 1920’s and has become one of the most trusted and friendly mass media. Today, its popularity is still strong, despite the outcome of many electronic media. In order to transform the radio into a viable medium of the 21st century, it will have to migrate from analogue to digital...
-
Carbon dioxide potential reduction using Start-Stop system in a car
PublicationOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Identification and non-integer order modelling of synchronous machines operating as generator
PublicationThis paper presents an original mathematical model of a synchronous generator using derivatives of fractional order. In contrast to classical models composed of a large number of R-L ladders, it comprises half-order impedances, which enable the accurate description of the electromagnetic induction phenomena in a wide frequency range, while minimizing the order and number of model parameters. The proposed model takes into account...
-
Prediction of CO2 emissions of a car using the discrete map of the operating conditions
PublicationW pracy przedstawiono propozycję opisu warunków eksploatacji pojazdów w wybranej aglomeracji miejskiej z użyciem dyskretnej mapy warunków eksploatacji. Mapa taka umożliwia prognozowanie wybranych parametrów eksploatacyjnych pojazdów dla przyjętych dróg przejazdu oraz różnych jednostek napędowych. Głównymi parametrami wyznaczanymi z użyciem dyskretnej mapy warunków eksploatacji są: całkowita energia przeznaczana do napędu wybranego...
-
Comparative analysis of earthships and conventional buildings in terms of investment and operating costs
PublicationThe aim of the master's thesis is to present the idea of earthships and compare them with conventional buildings in terms of investment and operating costs. Earthships are buildings erected from tires and other wastes whose characteristic feature is their self-sufficiency. The first part of the master's thesis is to discuss the basic issues related to the earthship building. The beginnings of tire homes and their development are...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublicationA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublicationThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
The concept of stream and system reliability on the example of the bakery industry
PublicationThis article presents a new concept of technological system reliability based on the analysis of the relationship of associations of elements of energy streams, matter, information, time and finance. The method of stream specification and the method of determining the reliability values of significant and supporting relationships are given. Relevant relationships between elements of system streams were defined as having one-time...
-
Numerical analysis of the flow rig for UWS spray examination in exhaust system-relevant conditions
PublicationIn the present study, a flow rig with optical access intended for spray investigations in exhaust system-relevant conditions was analysed in terms of flow and temperature in the spray area using numerical simulations. The operation of the rig was examined for a wide range of exhaust mass flow rates, temperatures and various forms of UWS (urea-water solution) spray plumes. The locations of the injector and thermocouple were verified....
-
Linux scheduler improvement for time demanding network applications, running on Communication Platform Systems
PublicationCommunication Platform Systems as ex. ATCA standard blades located in standardized chassis provides high level communication services between system peripherals. Each ATCA blade brings dedicated functionality to the system but can as well exist as separated host responsible for servicing set of task. According to platform philosophy these parts of system can be quite independent against another solutions provided by competitors....
-
Modelling and Control of a Brushless Multiphase Doubly-Fed Induction Generator in a Stand-Alone Wind Generation System
PublicationThe development of the novel multiphase brushless doubly-fed generator system and voltage controller for stand-alone mode configuration is proposed in this paper. The generator system is based on the new machine construction with multiphase control winding and traditional three-phase power winding. The dynamic model of multiphase brushless doubly-fed generator is presented, and the control strategy for voltage amplitude and frequency...
-
Design of synchronous generator two inputs regulator based on hinf control theory.
PublicationThe power system is highly nonlinear system, its dynamics depends on system network configuration, system loading… etc. To overcome the above mentioned difficulties and fulfill the performance requirements the different control methods are considered and tested for design of synchronous generator control system. Application of the H optimization method to synchronous generator regulator based on measurement of generator voltage...
-
Design of synchronous generator voltage regulator based on h control theory
PublicationThe power system is highly nonlinear system, which dynamics depends on system network configuration, system loading…etc. To overcome the above mentioned difficulties and to fulfill the performance requirements the different control methods are considered and tested for application to generating control unit. Application of the H optimization method to automatic voltage regulator is studied in this paper. Simulation results have...
-
Selected Issues of Hybrid Outboard Motors
PublicationThe aim of the research reported in the article was designing a hybrid drive system based on an outboard internal combustion engine offered by a selected producer and testing its operating characteristics. The article presents different designs of this type of drive which can be found in the literature and are available in the market. The designed hybrid outboard drive system was tested both on the laboratory test rig and in real...
-
Mobilny system do detekcji obiektów ferromagnetycznych z magnetometrami pompowanymi optycznie
PublicationW pracy przedstawiono mobilny system do detekcji obiektów ferromagnetycznych. Każdy obiekt ferromagnetyczny zaburza w swoim otoczeniu równomierność pola magnetycznego Ziemi. Zaburzenie to może być zmierzone za pomocą precyzyjnych magnetometrów. W prezentowanym mobilnym systemie zastosowano magnetometry pompowane optycznie pracujące w układzie różnicowym. W pracy opisano magnetometryczny system do detekcji obiektów ferromagnetycznych,...
-
Low-Power WSN System for Honey Bee Monitoring
PublicationThe paper presents a universal low-power system for biosensory data acquisition in scope of bees monitoring. We describe the architecture of the system, energy-saving components as well as we discuss the selection of used sensors. The work focuses on energy optimization in a scope of wireless communication. A custom protocol was implemented, which is the basis for presented energy-efficient devices. Data exchange process during...
-
Loosely-Tied Distributed Architecture for Highly Scalable E-Learning System
PublicationVast majority of modern e-learning products are based on client-server architecture and utilization of web-based technologies (WBT). Such approach permits easy creation of e-learning systems that do not require a complex, operating system dependant client software. Unfortunately there are also drawbacks of such solution. Because of the majority of mechanisms are located on the server, its usage levels trend to build up quickly...
-
Analysis and assessment of the acoustic emission suitability for determination of the energy states of a tribological system in the form of a four-ball tester friction node
PublicationThe present operating safety and cost reduction requirements of the compression ignition engines make it necessary to search for new methods of detecting their defects, e.g. by the analysis of acoustic emission signals coming from the slide bearings. The paper presents non-destructive measurements of acoustic emission (AE) in order to obtain information on the processes taking place in a tribological system under the continuously...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
An optimization approach to coexistence of Bluetooth and Wi-Fi networks operating in ISM environment
PublicationW artykule rozważono problem wzajemnych interferencji pomiedzy urządzeniami standardów IEEE 802.11b oraz Bluetooth (BT). Zaproponowano model optymalizacyjny bazujący na podejściu programowania liniowego. Uzyskano znaczącą porawę wykorzystania pasma ISM w przypadku koegzystencji sieci rozważanych standardów.
-
Measurement of the earth fault loop impedance in a low voltage network with operating loads
PublicationW artykule przedstawiono problematykę dokładności pomiaru impedancji pętli zwarciowej w sieciach z obciążeniami roboczymi. Klasyczne metody pomiarowe i mierniki mogą powodować błędy pomiaru przekraczające dopuszczalną wartość. Z tego powodu może wystąpić ryzyko porażenia prądem elektrycznym, ponieważ przy doziemieniu nie będzie spełniony warunek samoczynnego wyłączenia zasilania. Błędy pomiaru w sieci z obciążeniami roboczymi można...
-
a rule for vibration surveillance of manipulators in order to improve operating parameters of industrial robots
PublicationPrzedmiotem rozważań są drgania układu nośnego manipulatora IRb-6. Proponowane podejście ma na celu minimalizację poziomu drgań końcówki manipulatora. Dla niestacjonarnego układu sterowanego, którego zachowanie opisano we współrzędnych uogólnionych, zdefiniowano energetyczny wskaźnik jakości uwzględniający energię kinetyczną i potencjalną układu, a także - chwilową energię sygnału sterującego. Dalsze rozważania dotyczą tymczasowego...
-
The Issue of Operating Security Systems in Terms of the Impact of Electromagnetic Interference Generated Unintentionally
Publication -
Galvanic isolation circuit for measuring systems operating in environments with strong electromagnetic disturbances
Publication -
A XAS study of a highly diluted Pt electrocatalyst operating in PEM fuel cells
PublicationWe present an X-ray absorption spectroscopy (XAS) study of a low Pt content catalyst layer(Pt loading 0.1 mg c2) operating at the cathode of a proton exchange membrane fuel cell(PEMFC). This catalyst is based on the use of a mesoporous inorganic matrix as a support forthe catalyst Pt nanoparticles. Due to the high Pt dilution, in situ measurements of itsstructural properties by XAS are challenging and suitable experimental strategies...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
Operating and economical conditions of cooling water control for marine steam turbines condensers
PublicationW pracy dokonano analizy ekonomicznej i eksploatacyjnej sterowania pracą pomp wody chłodzącej skraplacze turbin okrętowych. Wzięto pod uwagę cechy konstrukcyjne pomp wody chłodzącej skraplacze główne i najnowsze wyniki badań dla takich pomp w zastosowaniach lądowych. Uwagę skupiono przede wszystkim na turbinowych parowych siłowniach okrętowych.
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublicationIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Rapid redesign of multiband antennas with respect to operating conditions and material parameters of substrate
PublicationThis work addresses geometry parameter scaling of multi-band antennas for Internet of Things applications. The presented approach is comprehensive and permits re-design of the structure with respect to both the operating frequencies and material parameters of the dielectric substrate. A two-step procedure is developed with the initial design obtained from an inverse surrogate model constructed using a set of appropriately prepared...
-
Józef Kotus dr hab. inż.
People -
Modular power converter with superconducting magnetic energy storage for electric power distribution system — Analysis and simulation
PublicationThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. This paper presents a modular approach of 300 kVA power converter operating with superconducting magnetic energy storage (SMES), which gives high dynamics together with high power and suitable capability for instantaneous energy storage. Analysis and simulation studies of selected power converter...
-
Android OS: A Review
PublicationDue to the technological development, mobile terminals have evolved into functionally sophisticated devices such as smartphones and tablets. The Android platform has become one of the most popular operating system with millions of new users each year. Despite many studies, none have provided a comprehensive description of this operating system. In this paper we present a review of the Android OS. We describe the platforms history...
-
The semi-Markov model of the process of appearance of sea-going ship propupsion system ability and inability states in application to determining the reliablity of these systems
PublicationThe article presents possible application of the theory of semi-Markov processes in creating the eight-state model of the process of appearance of the propulsion systems ability and inability states on sea-going vessels performing transportation tasks in a relatively long operating time t (t → ∞). The model has been proved to be able to be successfully used for determining the reliability of the abovementioned systems. The probability...
-
Robustness Analysis of a Distributed MPC Control System of a Turbo-Generator Set of a Nuclear Plant – Disturbance Issues
PublicationTypically, there are two main control loops with PI controllers operating at each turbo-generator set. In this paper, a distributed model predictive controller with local quadratic model predictive controllers for the turbine generator is proposed instead of a set of classical PI controllers. The local quadratic predictive controllers utilize step-response models for the controlled system components. The parameters of these models...
-
Power Hardware-In-the-Loop Approach for Autonomous Power Generation System Analysis
PublicationThe article presents the Power Hardware-In-the-Loop (PHIL) dynamic model of a synchronous generator of 125 kVA for autonomous power generation system analysis. This type of system is typically composed of electrical energy sources in the form of several diesel generator units with synchronous machines, the main distribution switchboard and different loads. In modern power distribution systems, the proposed power management strategies...
-
The structure of the Polish banking sector in 2004-2018
Open Research DataDynamic changes in the banking system in the 1990s contributed to the relative stability of the number of banks in all sectors (state-owned, private, cooperative) after 2004. The total number of banks (including credit institutions) has decreased since 2004 from 653 to 612 in 2018 - it should therefore be noted that in the analyzed period the Polish...
-
Subjective Quality Evaluation of Speech Signals Transmitted via BPL-PLC Wired System
PublicationThe broadband over power line – power line communication (BPL-PLC) cable is resistant to electricity stoppage and partial damage of phase conductors. It maintains continuity of transmission in case of an emergency. These features make it an ideal solution for delivering data, e.g. in an underground mine environment, especially clear and easily understandable voice messages. This paper describes a subjective quality evaluation of...
-
Dynamic Signal Strength Mapping and Analysis by Means of Mobile Geographic Information System
PublicationBluetooth beacons are becoming increasingly popular for various applications such as marketing or indoor navigation. However, designing a proper beacon installation requires knowledge of the possible sources of interference in the target environment. While theoretically beacon signal strength should decay linearly with log distance, on-site measurements usually reveal that noise from objects such as Wi-Fi networks operating in...
-
Multiregional PI control strategy for dissolved oxygen and aeration system control at biological wastewater treatment plant
PublicationThe dissolved oxygen is a key parameter for biological processes at wastewater treatment plant. The dissolved oxygen tracking problem is one of the most complex and fundamental issue of biological processes. The paper proposes a new multiregional control strategy for dissolved oxygen tracking problem. The aeration system is included in overall control structure. The control mechanism within the operating point area is based on...
-
System do prototypowania bezprzewodowych inteligentnych urządzeń monitoringu audio-video
PublicationW komunikacie przedstawiono system prototypowania bezprzewodowych urządzeń do monitoringu audio-video. System bazuje na układach FPGA Virtex6 i wielu dodatkowych wspierających urządzeniach jak: szybka pamięć DDR3, mała kamera HD, mikrofon z konwerterem A/C, moduł radiowy WiFi, itp. Funkcjonalność systemu została szczegółowo opisana w komunikacie. System został zoptymalizowany do pracy pod kontrolą systemu operacyjnego Linux, zostały...
-
The excitation controller with gain scheduling mechanism for synchronous generator control
PublicationThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
Effect of Hybrid Modulation on Performance of Wireless Battery Charger Operating in CC/CV Mode
Publication -
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part I)
PublicationW artykule przestawnie są problemy rozruchu i działania zespołów i układów hydraulicznych w niskich temperaturach otoczenia. Z tych powodów autor przebadał hydrauliczne zespoły i układy w warunkach szoku termicznego (oziębione zespoły zasilano gorącym czynnikiem roboczym). Określono parametry rozruchu w tych warunkach kilku zespołów oraz układów hydraulicznych, przy których ich eksploatacja jest bezpieczna. Badania eksperymentalne...
-
Assessment of the Resistance Value of Trash Racks at a Small Hydropower Plant Operating at Low Temperature
Publication -
1.2V low-power four-quadrant CMOS transconductance multiplier operating in saturation region.
PublicationW pracy opisano niskomocową strukturę układową liniowego transkonduktancyjnego mnożnika czteroćwiartkowego pracującego w zakresie nasycenia. Układ analizowano z uwzględnieniem standardowego 0,35-mikrometrowego procesu CMOS. Przeprowadzone symulacje przy pomocy programu SPICE wykazały wysoką liniowość w odniesieniu do obu wejść sterujących X, Y. Np. dla sygnału harmonicznego 1 MHz; 0,3Vp-p na wejściu Y uzyskano zniekształcenia...
-
The modal control vibration surveillance of manipulators as a mean of improving operating parameters of industrial robots.
PublicationNowe zastosowania robotów, a przede wszystkim - operacje szybkiego montażu, technika kosmiczna oraz operacje manipulacyjne dużymi masami (niekiedy przekraczającymi masę własną manipulatora), stawiają przed robotami coraz to większe wymagania dotyczące m.in. dużej dokładności i powtarzalności pozycjonowania. Spełnienie powyższych wymagań, bez redukcji poziomu drgań występujących w układzie nośnym manipulatora, jest trudne do uzyskania....
-
Dynamic impedance measurements of the Direct Methanol Fuel Cell cathode at various operating temperatures
PublicationThis article discusses the application of impedance analysis for diagnosing the cathode of a direct methanol fuel cell at various operating temperatures. The Dynamic Electrochemical Impedance Spectroscopy technique coupled with a linear current scan was applied for this purpose. This technique allowed the observation of changes in the cathode's properties in the fuel cell operating under real working conditions. An equivalent model...
-
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part II)
PublicationPodczas rozruchu zespołów hydraulicznych w warunkach szoku termicznego dochodzi do dynamicznej zmiany wymiarów elementów tych zespołów. Odkształcenia elementów powodują zmianę efektywnego luzu między współpracującymi elementami. Na zmiany luzu ma pływ między innymi: różnica temperatur pomiędzy gorącym olejem a zimnym zespołem hydraulicznym, natężeniem przepływu czynnika roboczego, konstrukcji zespołu, rodzaju materiału i kształtu...